Wolf ICBPW482418 Installation Instructions Manual

PRO VENTILATION HOODS

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

3

ENGLISH 4

ESPÃNOL 30

FRANÇAIS 56

ITALIANO 82

DEUTSCH 108

As you follow these instructions, you will

notice WARNING and CAUTION symbols.

This blocked information is important for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

5

WOLF PRO VENTILATION HOODS

INSTALLATION REQUIREMENTS

IMPORTANT NOTE:

This installation must be

completed by a qualified installer.

Installer:

Please read the entire Installation

Instructions prior to installation. Save these

instructions for the local inspector’s refer-

ence, then leave them with the homeowner.

Homeowner:

Please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

Any questions or problems about the installa-

tion should be directed to your Wolf dealer or

visit our website at wolfappliance.com.

IMPORTANT NOTE:

This appliance must be

installed in accordance with local codes. The

correct voltage, frequency and amperage must

be supplied to the appliance from a dedicated,

grounded circuit which is protected by a

properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and

amperage ratings are listed on the product

rating plate.

Record the model and serial numbers before

installing the hood. Both numbers are listed on

the rating plate, located inside the left wall of

the hood shell. Refer to the illustrations below.

A)

Installation work and electrical

wiring must be done by qualified

person(s) in accordance with all

applicable codes and standards,

including fire-rated construction.

B)

When cutting or drilling into wall

or ceiling, do not damage electrical

wiring and other hidden utilities.

C)

Ducted fans must always be vented

to the outdoors. Regulations

concerning the discharge of air have

to be fulfilled.

D)

The air must not be discharged into

a flue that is used for exhausting

fumes from appliances burning gas

or other fuels.

WARNING – TO REDUCE THE

RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

RATING PLATE

INFORMATION

Model Number

Serial Number

Rating plate location—wall hoods

Rating plate located

inside hood shell

To reduce the risk of fire and to

properly exhaust air, be sure to

duct air outside. Do not vent

exhaust air into spaces within

walls or ceilings or into attics,

crawl spaces or garages.

Rating plate location—hood liners

Rating plate located

inside hood liner shell

6

WOLF PRO VENTILATION HOODS

LIST OF MATERIALS

WALL HOODS

The following is a list of materials shipped

with the Wolf Pro wall ventilation hood.

Stainless steel wall hood

Transition with backdraft damper—

attached inside hood (needs to be removed

prior to installation)

Control knobs—two for 610 mm deep

hoods, three for 686 mm deep hoods

Filters (installed in hood)

Grease cups (shipped loose in carton)

Halogen receptacles for lighting— bulbs not

included

Wood mounting support

Installation package (part #810555)

mounting hardware included:

(10) #8 x 76 mm Phillips drywall screws,

(12) #10 x 38 mm pan head wood screws,

(12) #12 flat washers

(4) #8 x 76 mm Phillips sheet metal screws

Installation Instructions

Use & Care Information

Wolf logo nameplate

Bottle of Signature stainless steel cleaner

PRO HOOD LINERS

The following is a list of materials shipped

with the Wolf Pro ventilation hood liner.

Stainless steel hood liner

Transition with backdraft damper (attached

inside hood liner—needs to be removed)

Filters (installed in hood liner)

Installation package (taped to filters)

includes:

(8) #10 x 51 mm Phillips head wood screws

(8) #10 washers

(4) hollow wall anchors

Installation Instructions

Use & Care Information and product

registration card

INSTALLATION CONSIDERATIONS

Wolf Pro wall ventilation hoods and hood

liners are recommended for use with all Wolf

cooking appliances.

Wolf Pro ventilation hood liners are available

to accommodate 914 mm, 1067 mm, 1219 mm,

1372 mm and 1524 mm wide hoods.

IMPORTANT NOTE:

For optimal performance,

a Pro 686 mm deep wall hood is recom-

mended for use with ranges and rangetops

that contain a charbroiler or griddle.

Proper installation is the responsibility

of the installer.

Make sure you have the tools and materials

necessary for proper installation.

IMPORTANT NOTE:

Wolf Pro ventilation

hoods and liners are shipped without the

blower assembly. Wolf internal and remote

blower assemblies are available, refer to page

27. Use only a Wolf blower with Pro wall venti-

lation hoods and hood liners.

IMPORTANT NOTE:

Wolf recommends that

the Pro wall ventilation hood or hood liner be

installed 762 mm to 914 mm above the coun-

tertop.

If the supply cord is damaged, it must be

replaced by the manufacturer, it’s agent or

similarly qualified persons to avoid a

hazard.

610 mm Wall Hood

686 mm Wall Hood

Pro Hood Liner

7

INSTALLATION INSTRUCTIONS

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

the international

section of our

website,

wolfappliance.com.

DECORATIVE HOODS

A decorative hood can be created out of wood,

plaster, tile or metal. The shape of the decora-

tive hood is not critical. The only place where

the hood liner and outside cover must meet is

at the bottom edge of the liner. The decorative

hood and liner must fit at the bottom edge in

both width and depth.

The height of the hood liner does not have to

be the same as the height of the decorative

hood and is generally shorter.

The top depth of the hood liner, which is

305 mm standard, must be less than the

interior depth of the decorative hood. Measure

the interior depth of the hood at the top height

of the liner to make sure the liner will fit inside

the decorative hood.

The hood liner comes standard with a 102 mm

lower reveal. Be sure to include this dimension

in your decorative hood selection.

Always use the interior measurements of the

decorative hood and measure in multiple

places. Use the smallest dimensions to verify

hood liner specifications.

INSTALLATION CONSIDERATIONS

ELECTRICAL REQUIREMENTS

Wolf Pro wall ventilation hoods and hood

liners require a separate, grounded 220-240 V

AC, 50/60 Hz power supply. Locate the electri-

cal supply within the shaded area shown in the

Installation Specifications illustrations on

pages 8–9.

You must follow all building and electrical

code regulations. In addition, be aware of local

codes and ordinances when installing your

service.

DUCT COVER (WALL HOOD ONLY)

If you are installing a Wolf duct cover with the

Pro wall hood, refer to instructions on page 16

before installing the hood.

RECIRCULATING KIT

(WALL HOOD ONLY)

If you are installing the accessory recirculating

kit, refer to the instructions included with the

kit before installing the hood. Accessory kits

are available through your Wolf dealer.

HORIZONTAL DISCHARGE KIT

(WALL HOOD ONLY)

If a horizontal discharge is needed for installa-

tion of a 610 mm or 686 mm deep wall hood,

an accessory horizontal discharge kit is

required. Refer to the instructions included in

the kit for complete mounting and blower

options. Accessory kits are available through

your Wolf dealer.

8

WOLF PRO VENTILATION HOODS

457 mm

OVERALL

HEIGHT

OVERALL WIDTH

102 mm

610 mm

OVERALL DEPTH

305

mm

OVERALL WIDTH

686 mm

OVERALL DEPTH

305

mm

457 mm

OVERALL

HEIGHT

102 mm

610 mm DEEP WALL HOODS

Overall Widths 762 mm, 914 mm,

1067 mm, 1219 mm, 1372 mm,

1524 mm and 1676 mm

Overall Height

457 mm

Overall Depth 610 mm

Shipping Weight (shell only) 30–57 kg

Unit dimensions may vary to ±3 mm.

686 mm DEEP WALL HOODS

Overall Widths 762 mm, 914 mm,

1067 mm, 1219 mm, 1372 mm,

1524 mm and 1676 mm

Overall Height

457 mm

Overall Depth 686 mm

Shipping Weight (shell only) 42–74 kg

Unit dimensions may vary to ±3 mm.

OVERALL DIMENSIONS – WALL HOODS

610 mm Deep Wall Hood

686 mm Deep Wall Hood

762 mm

TO

914 mm

TO COUNTERTOP

762 mm

TO

914 mm

TO COUNTERTOP

457 mm

HEIGHT

OF HOOD

610 mm

686 mm

DEPTH OF HOOD

WIDTH OF HOOD

NOTE: 610 mm and 686 mm deep wall hoods have a vertical discharge. A horizontal discharge kit is available as a sales accessory.

E

152

mm

127

mm

LOCATION OF ELECTRICAL

INSTALLATION SPECIFICATIONS – WALL HOODS

610 mm and

686 mm Deep

Wall Hoods

9

INSTALLATION INSTRUCTIONS

PRO HOOD LINERS

Overall Widths 873 mm, 1026 mm,

1178 mm, 1330 mm

and 1483 mm

Overall Height

305 mm

Overall Depth 572 mm

Shipping Weight (shell only) 20–29 kg

Dimensions may vary to

+

–

3 mm.

OVERALL DIMENSIONS – LINERS

762 mm TO

914 mm

TO COUNTERTOP

762 mm TO

914 mm

TO COUNTERTOP

E

305 mm

HEIGHT OF LINER

572 mm

DEPTH OF LINER

WIDTH OF LINER

DECORATIVE HOOD

HOOD LINER

DECORATIVE HOOD

152

mm

127

mm

LOCATION OF ELECTRICAL

INSTALLATION SPECIFICATIONS – LINERS

TOP WIDTH

SUBTRACT 152 mm FROM OVERALL WIDTH

305 mm

OVERALL

HEIGHT

OVERALL WIDTH

102 mm

572 mm

OVERALL DEPTH

305

mm

76 mm 76 mm

Pro Hood Liners

10

C

TO CENTER

OF TRANSITION

D

A

WIDTH

OF HOOD

TO CENTER

OF TRANSITION

B

HEIGHT OF

TRANSITION

610 mm and 686 mm Deep Wall Hoods –

Transition Included

610 mm Deep Wall Hoods

Model (A) (B) (C) (D)

ICBPW302418 762 mm 229 mm 375 mm 143 mm

ICBPW362418 914 mm 229 mm 451 mm 143 mm

ICBPW422418 1067 mm 229 mm 527 mm 143 mm

ICBPW482418 1219 mm 229 mm 603 mm 143 mm

ICBPW542418 1372 mm 229 mm 679 mm 143 mm

ICBPW602418 1524 mm 229 mm 756 mm 143 mm

ICBPW662418 1676 mm 229 mm 832 mm 143 mm

686 mm Deep Wall Hoods

Model (A) (B) (C) (D)

ICBPW302718 762 mm 229 mm 375 mm 143 mm

ICBPW362718 914 mm 229 mm 451 mm 143 mm

ICBPW422718 1067 mm 229 mm 527 mm 143 mm

ICBPW482718 1219 mm 229 mm 603 mm 143 mm

ICBPW542718 1372 mm 229 mm 679 mm 143 mm

ICBPW602718 1524 mm 229 mm 756 mm 143 mm

ICBPW662718 1676 mm 229 mm 832 mm 143 mm

Letters correspond to those in the illustrations.

The illustration and chart provide dimensions

specific to Pro 610 mm and 686 mm deep wall

hood models. These dimensions are critical for

proper installation.

TRANSITION SPECIFICATIONS – WALL HOODS

The illustration and chart provide dimensions

critical for proper installation of the Pro hood

liner.

Pro Hood Liners

Model (A) (B) (C) (D)

ICBL342212 873 mm 238 mm 437 mm 152 mm

ICBL402212 1026 mm 238 mm 513 mm 152 mm

ICBL462212 1178 mm 238 mm 589 mm 152 mm

ICBL522212 1330 mm 238 mm 665 mm 152 mm

ICBL582212 1483 mm 238 mm 741 mm 152 mm

Letters correspond to those in the illustration.

A

WIDTH OF

HOOD LINER

D

C

TO CENTER

OF TRANSITION

TO CENTER

OF TRANSITION

B

HEIGHT OF

TRANSITION

TRANSITION SPECIFICATIONS – LINERS

WOLF

PRO VENTILATION HOODS

11

WALL HOOD INSTALLATION

STEP 1: INSTALL DUCTWORK

IMPORTANT NOTE:

Wolf recommends that

the Pro wall ventilation hood be installed

762 mm to 914 mm above the countertop.

IMPORTANT NOTE:

Consult a qualified HVAC

Engineer for specific ducting applications.

IMPORTANT NOTE:

All Pro 610 mm and 686

mm deep wall hoods must exhaust to the

outdoors except when used with the accessory

recirculating kit (Models ICBPW302418,

ICBPW362418, ICBPW302718 and ICBPW362718

with 1000 CMH internal blower). Always use

metal ducting. Do not use flex ducting.

Decide where the ductwork will run between

the wall hood and the outside. A straight, short

duct run will allow the hood to perform more

efficiently. Limit the number of elbows and

transitions to as few as possible. Long duct

runs, elbows and transitions will reduce the

performance of the hood. Wolf recommends

the maximum linear duct run be no greater

than 15 m.

IMPORTANT NOTE:

There is a possibility of

noise issues, if there is a short duct run

coupled with a remote blower.

IMPORTANT NOTE:

If a horizontal discharge

is needed for installation of a 610 mm or

686 mm deep wall hood, an accessory hori-

zontal discharge kit is required. Refer to

instructions included with the kit for complete

mounting and blower options. Accessory kits

are available through your Wolf dealer.

DUCTWORK INSTALLATION

THROUGH ROOF

610 mm

DEPTH OF HOOD

NOTE: HORIZONTAL DISCHARGE REQUIRES AN ACCESSORY KIT.

762 mm TO 914 mm

COUNTERTOP

TO BOTTOM OF

HOOD

457 mm

HEIGHT OF HOOD

Ducting for 610 mm deep wall hoods

To reduce the risk of fire, use only metal

ductwork.

INSTALLATION INSTRUCTIONS

12

WOLF PRO VENTILATION HOODS

762 mm TO

914 mm

COUNTERTOP

TO BOTTOM OF

HOOD

457 mm

HEIGHT OF HOOD

DUCTWORK INSTALLATION

THROUGH ROOF

686 mm

DEPTH OF HOOD

NOTE: HORIZONTAL DISCHARGE REQUIRES AN ACCESSORY KIT.

Ducting for 686 mm deep wall hoods

WALL HOOD INSTALLATION

STEP 1: INSTALL DUCTWORK

Always install a roof or wall cap if you are not

installing a remote blower. Connect 254 mm

round metal ductwork to the cap and work

back towards the hood. Use duct sealing tape

on joints between ductwork sections.

Wolf Pro 610 mm and 686 mm deep wall

hoods come standard with a backdraft damper

included in the transition assembly. Local

codes may require the use of an additional

backdraft damper. Contact your local HVAC

professional for specific requirements. In cold

weather installations, a backdraft damper is

necessary to minimize the backflow of cold air

into the room.

Local building codes may require the use of

make-up air. Consult your local HVAC profes-

sional for specific requirements in your area.

To reduce the risk of fire and electric

shock, install this ventilation hood only

with a Wolf blower. Blower model

numbers are listed on page 27.

IMPORTANT NOTE:

The screws should be

countersunk so that they are below flush.

Install the flat metal hood retaining brackets

to the wood mounting support at the loca-

tions shown in the illustration and the chart

below. Use the provided #10 x 38 mm

screws and washers to secure these

brackets in place. The metal bracket should

be mounted 13 mm above the top of the

wood mounting support.

IMPORTANT NOTE:

The location of this wood

mounting support and retaining bracket allow

for 13 mm clearance at the top of the hood for

ease of installation. This gap will be taken up

during final mounting of the hood to the wood

mounting support.

Refer to the illustration below for the location

of mounting holes for the Pro 610 mm and

686 mm deep wall hoods.

13

INSTALLATION INSTRUCTIONS

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

the international

section of our

website,

wolfappliance.com.

If wall framing is not available, wall

anchors must be used.

113

mm

64

mm

MOUNTING

HOLES

Location of mounting holes

WALL HOOD INSTALLATION

STEP 2: WALL PREPARATION

Construct the wood wall framing flush with

the wall studs and centered in the location

that the hood will be mounted. Finish the

wall surface.

Attach the provided wood mounting

support. Refer to the illustration and the

chart below. The wood support s hould be

centered within the desired hood location.

Use the provided 76 mm screws to attach

the support to the wall. The location of

these screws should correspond to the

wood supports within the walls or the

framing.

Framing must be tied together to provide

enough structural strength to support the

weight of the hood and internal blower,

if applicable.

Failure to install the screws or fixing

device in accordance with these instruc-

tions may result in electrical hazards.

A

CENTER LINE

OF HOOD

LOCATION

B

TO BOTTOM

OF HOOD

762 mm

TO

914 mm

BOTTOM OF

HOOD TO

COUNTERTOP

A

92 mm

19 mm13 mm

HOOD RETAINING

BRACKET

Wood mounting support

Wood Mounting Support

Hood Width (A) (B)

762 mm 298 mm 384 mm

914 mm 311 mm 384 mm

1067 mm 387 mm 384 mm

1219 mm 464 mm 384 mm

1372 mm 540 mm 384 mm

1524 mm 616 mm 384 mm

1676 mm 692 mm 384 mm

14

WOLF PRO VENTILATION HOODS

WALL HOOD INSTALLATION

STEP 3: HOOD PREPARATION

IMPORTANT NOTE:

If a duct cover is to be

used, follow instructions on page 16 before

installing the wall hood. If you are installing a

recirculating kit, refer to instructions included

with the kit before installing the wall hood.

IMPORTANT NOTE:

Wolf recommends

installing the internal blower to the back plate

prior to mounting the hood.

If you are installing 1000 CMH blower

(813160), 1600 CMH blower (813161) or a

1900 CMH blower (813162), refer to the

internal blower information on page 23 and

follow installation instructions provided

with the blower assembly.

The hood assembly is shipped with the

back plate/transition attached. The

transition is shipped upside down in the top

of the hood. It must be removed and rein-

stalled in the proper position.

Remove the filters by pushing each filter up

at the angle it is placed in, and rotate down.

Remove the center filter first. Then take out

the grease cups placed on the bottom edge

of the hood coinciding with the bottom

edge of the filters. Gloves should be worn

to provide the proper grip when removing

filters.

Detach the back plate/transition assembly

from the hood by removing the screws

from the top and back of the assembly.

Refer to the illustration below.

Separate the transition from the back plate

by removing the shipping nut from the

inside of the back plate.

Position the back plate in the desired

location and mark the mounting holes on

the wood support. Drill pilot holes for the

mounting hardware.

If you are installing a remote blower, drill

an additional 22 mm hole through the wood

framing for the conduit in order to run

power to the blower. Refer to the illustra-

tion on page 20 for location of the electrical

box and to the remote blower information

on pages 25–26. Also, follow installation

instructions provided with the blower

assembly.

IMPORTANT NOTE:

Do not run wiring for the

remote blower through the ductwork.

Back plate/transition assembly

15

INSTALLATION INSTRUCTIONS

WALL HOOD INSTALLATION

STEP 4: REATTACH BACK PLATE

Follow these instructions to reattach the back

plate to the wall hood:

Attach the transition to the back plate using

the four shipping screws provided in the

hardware mounting kit.

Reinstall the shipping screws removed

previously from the top and back of the

back plate.

Use duct sealing tape to ensure a tight seal

from the transition to the back plate.

IMPORTANT NOTE:

If additional support is

required, drill supplementary mounting holes

in the back plate and use these holes to attach

the hood assembly to the wall framing.

Due to the weight of the hood, be

sure to have adequate manpower for

installation.

STEP 5: HOOD INSTALLATION

IMPORTANT NOTE:

If a backsplash is to be

used, it should be installed before the wall

hood is mounted. Refer to instructions

included with the backsplash.

Follow these instructions to install the wall

hood:

Align the mounting holes in the back plate

of the hood assembly with the metal

retaining brackets on the wood mounting

support. Refer to the illustration below for

location of the mounting holes.

Position the hood and install the #10 x

38 mm screws and washers (included in the

hardware mounting kit) through the

mounting holes on the back plate. Refer to

the illustration below. Verify that the screws

engage the wood mounting support.

Attach the transition to existing ductwork

with sheet metal screws and duct sealing

tape.

113

mm

64

mm

MOUNTING

HOLES

Location of mounting holes Hood installation

16

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

the international

section of our

website,

wolfappliance.com.

DUCT COVER INSTALLATION

WALL HOODS ONLY

Optional

Duct Cover

Mounting

Screws

Duct cover installation

Installing a duct cover assembly will

impact all aspects of the hood installa-

tion including hood location, ducting,

electrical placement and the mounting

surface.

Duct covers 152 mm, 305 mm, 457 mm and

610 mm high in widths to match all wall hoods

are available through your Wolf dealer. To

obtain local dealer information, visit our

website, wolfappliance.com.

IMPORTANT NOTE:

If an optional duct cover

is to be used with any Wolf Pro wall hood,

follow these instructions before installing the

hood:

Remove all screws from the front edge of

the back panel on the top of the wall hood.

Leave the two screws on the sides as there

is a relief in the duct cover for them.

Attach the duct cover from the inside of the

hood through the filter opening using the

screws provided.

Leave screws partially loose until all screws

are installed. Check alignment of the duct

cover with the hood and tighten the four

corner screws to secure the duct cover.

Tighten all remaining screws.

Continue with the installation of the wall

hood.

WOLF PRO VENTILATION HOODS

17

305 mm

HEIGHT OF LINER

HOOD LINER

DUCTWORK INSTALLATION

THROUGH ROOF

254 mm ROUND DUCT

SOFFIT OR CABINET

OR DUCT COVER

VERTI

C

AL DI

SC

HAR

G

E

O

NLY F

O

R VENTILATI

O

NH

OO

D LINER

S

.

VERTICAL DISCHARGE

572 mm

DEPTH OF LINER

DECORATIVE HOOD

762 mm

TO

914 mm

COUNTERTOP

TO BOTTOM OF

DECORATIVE HOOD

914 mm

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

TRANSITION

565 mm W x 229 mm D

TO 254 mm ROUND 254 mm H

DIMENSIONS INCLUDE FLANGES

ROOF CAP OR REMOTE BLOWER

HOOD LINER INSTALLATION

STEP 1: INSTALL DUCTWORK

IMPORTANT NOTE:

Wolf recommends that

the Pro ventilation hood liner be installed

762 mm to 914 mm above the countertop.

IMPORTANT NOTE:

Consult a qualified HVAC

Engineer for specific ducting applications.

IMPORTANT NOTE:

All Wolf ventilation hood

liners must exhaust to the outdoors. Always

use metal ducting. Do not use flex ducting.

Decide where the ductwork will run between

the hood liner and the outside. A straight,

short duct run will allow the hood liner to

perform more efficiently. Limit the number of

elbows and transitions to as few as possible.

Long duct runs, elbows and transitions will

reduce the performance of the hood liner. Wolf

recommends the maximum linear duct run be

no greater than 15 m. The Pro hood liner has a

vertical discharge.

IMPORTANT NOTE:

There is a possibility of

noise issues, if there is a short duct run

coupled with a remote blower.

Always install a roof or wall cap if you are not

installing a remote blower. Connect 254 mm

round metal ductwork to the cap and work

back towards the hood. Use duct sealing tape

on joints between ductwork sections.

Wolf Pro hood liners come standard with a

backdraft damper included in the transition

assembly. Local codes may require the use of

an additional backdraft damper. Contact your

local HVAC professional for specific require-

ments. In cold weather installations, a back-

draft damper is necessary to minimize the

backflow of cold air into the room.

Local building codes may require the use of

make-up air. Consult your local HVAC profes-

sional for specific requirements in your area.

To reduce the risk of fire, use only metal

ductwork.

To reduce the risk of fire and electric

shock, install this ventilation hood liner

only with a blower manufactured by

Wolf. Blower model numbers are listed

on page 27.

Ducting for Pro hood liners

INSTALLATION INSTRUCTIONS

18

HOOD LINER INSTALLATION

STEP 2: WALL PREPARATION

Construct the wood wall framing flush with

the wall studs and centered in the location

that the hood liner will be mounted.

Refer to the illustrations below for the location

of mounting holes for Pro hood liners and a

cross-section of a typical installation.

Framing must be tied together and to

ceiling joists to provide enough structural

strength to support the weight of the hood

liner and internal blower, if applicable.

Decorative

Hood

#10 Screw

Hood Liner

13 mm Drywall

Installation cross-section

If wall framing is not available, wall

anchors must be used.

70

mm

203 mm

102

mm

51

mm

Mounting holes for hood liners

WOLF PRO VENTILATION HOODS

19

INSTALLATION INSTRUCTIONS

HOOD LINER INSTALLATION

STEP 3: HOOD LINER PREPARATION

If you are installing 1900 CMH blower

(813162), refer to the internal blower infor-

mation on page 24 and follow installation

instructions provided with the blower.

The hood liner assembly is shipped with the

transition attached. The transition is shipped

upside down in the top of the hood liner. It

must be removed and reinstalled in the

proper position. Refer to the illustration on

page 18.

Remove the filters by pushing each filter up

at the angle it is placed in, and rotate down.

Remove the center filter first. Gloves should

be worn to provide the proper grip when

removing filters.

Remove the screws (8) that hold the filter

frame in place. Remove the bottom and two

sides of the filter frame and set aside for

replacing at a later time. Remove the transi-

tion by removing the (4) mounting screws.

Attach the transition onto the top of the liner

with the (4) mounting screws. Refer to the

illustrations on page 24.

Attach the transition to existing ductwork

with sheet metal screws and duct sealing

tape.

If you are installing a remote blower, drill a

22 mm hole through the wood framing for

the conduit. Refer to the remote blower

information on pages 25–26 and follow

installation instructions provided with the

blower.

IMPORTANT NOTE:

Do not run wiring for the

remote blower through the ductwork.

STEP 4: INSTALL THE HOOD LINER

IMPORTANT NOTE:

If a backsplash is to be

used, it should be installed before the hood

liner is mounted.

Position the hood liner in the desired location

on the wall. Install the #10 x 59 mm screws

through the mounting holes on the back plate.

Verify that the screws engage the wall studs or

framing. If not, wall anchors must be used.

IMPORTANT NOTE:

If additional support is

required for the hood liner, drill supplementary

mounting holes in the back plate and use these

holes to attach the hood liner assembly to the

wall framing.

Due to the weight of the hood liner, be

sure to have adequate manpower for

installation.

20

Do not remove the control knob bezel to

access hood wiring; this will damage the

bezel assembly.

Location of electrical box—wall hoods

IMPORTANT

NOTE

You must follow

all building and

electrical code

regulations. In

addition, be aware

of local codes and

ordinances when

installing your

service.

ELECTRICAL WIRING

This ventilation hood must be properly

grounded. This unit should be installed by

a qualified electrician in accordance with

all applicable local electrical codes.

Before servicing or cleaning unit, switch

power off at service panel and lock the

service disconnecting means to prevent

power from being switched on acciden-

tally. When the service disconnecting

means cannot be locked, securely fasten a

prominent warning device, such as a tag,

to the service panel.

Cord anchorage must be used at both ends

of the fixed wiring.

Remove the electrical box cover from the

back plate. Using the terminal block,

connect brown wire to power supply brown

wire, blue wire to power supply blue wire

and green/yellow striped wire to

green/yellow striped wire or bare wire.

Place all wiring connections inside the

electrical box and reinstall on the back plate

in the upper right-hand corner. Make sure

that the wires are secure and that no wires

are pinched between the cover and box.

Follow these instructions to install wiring for

all Wolf Pro wall hoods:

Run a circuit from the service panel to the

electric box on the back plate.

Maximum power requirements with motors:

220-240 V AC 50/60 Hz

2–6 Amps

0.46–1.37 kW

See unit rating label for specific power

requirements.

Wiring diagram for the unit is located on the

outside of the back panel.

Run the fixed wiring through the holes in the

back plate to the electrical box. Refer to the

illustration below for the location of the

electrical box.

IMPORTANT NOTE:

Connection of this appli-

ance should be through a fused connection

unit or a suitable isolator, which complies with

national and local safety regulations. The

on/off switch should be easily accessible after

the appliance has been installed. If the switch

is not accessible after installation (depending

on country) an additional means of disconnec-

tion must be provided for all poles of the

power supply. When switched off there must

be an all pole contact gap of 3 mm in the

isolator switch. This 3 mm contact disconnect

gap must apply to any isolator switch, fuses

and/or relays according to EN60335.

Electrical

Box

WOLF PRO VENTILATION HOODS

48 mm

89 mm

318 mm

Pro hood liner wiring location

La page charge ...

Wolf ICBPW482418 Installation Instructions Manual

Wolf ICBPW482418 Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents