SportsArt N971/N973 Le manuel du propriétaire

N971/N973 OWNER’S MANUAL CONTENTS

1. INTRODUCTION ........................................................................... 2

2. SAFETY PRECAUTIONS ............................................................. 4

3. LIST OF PARTS ............................................................................. 5

4. ASSEMBLE THE PRODUCT ......................................................... 7

STEP 1 Install the Foot Covers ............................................................... 7

STEP 2 N971 Machine Assembly Instructions ............................................. 8

STEP 3 Install the Storage Tray .............................................................. 9

STEP 4 Secure the Unit............................................................................. 10

STEP 5 Cable Tension Adjustment Instructions ........................................13

STEP 6 Unit Inspection ....................................................................... 14

5. OPERATE THE PRODUCT ............................................................. 15

OPERATION Safety Operating Area ........................................................... 15

OPERATION Exercising Instructions .......................................................... 17

6. MAINTENANCE ............................................................................... 19

MAINTENANCE .Safety Precautions ......................................................... 19

MAINTENANCE Guide Rod Cleaning and Lubricating ................................. 20

MAINTENANCE Important Note ............................................................... 21

MAINTENANCE Schedule ..................................................................... 22

MAINTENANCE Task List ...................................................................... 23

MAINTENANCE Maintenance Log ............................................................ 24

7. CONSIGNES DE SÉCURITÉ IMPORTANTES ............................... 25

8. APPENDIXES ................................................................................. 26

APPENDIXES Exploded Diagram ............................................................ 26

2

1. INTRODUCTION

Congratulations on the purchase of a high quality SportsArt product, the N971/N973

Cable Cross Over / Cable Tower machine. Constructed of high quality materials

and designed for years of reliable performance, this product was made for full

commercial use.

Before this product is assembled or operated, we recommend that you familiarize

yourself with this manual. Understanding the correct assembly and operation of

this product will help ensure that exercisers obtain their tness goals safely and

successfully.

N973

3

N971

4

2. SAFETY PRECAUTIONS

This product was designed and built for optimum safety. However certain

precautions apply during the use of this product. Please note the following safety

precautions:

• Please read the entire manual before assembly and operation. Make

sure the product is installed and operated as instructed in this manual.

• Assemble and operate the product on a solid, level surface. Do not use

outdoors or near water, including pools and saunas.

• Check the product before every use. Make sure all parts are assembled,

and all fasteners are tightened. Do not use the product if it is disassembled

in any way.

• Wear proper workout clothing. Do not wear loose clothing. Do not wear

shoes with leather soles or high heels. Tie all long hair back. Do not go

barefoot on this product.

• Keep away from moving parts. Moving parts may or may not stop

immediately if an object becomes caught or impedes normal motion.

• Use this product only for its intended purpose as described in this manual.

• Be careful when mounting and dismounting the unit.

• Never operate this product if it has been damaged in any way. If it is

not working properly, or has been dropped or damaged, contact a service

technician for repairs.

• Do not use accessories or parts that are not specically recommended

by the manufacturer (SportsArt) . Such parts might cause injuries or cause

the unit to fail and void the warranty. We will not be responsible for any

safety issue that arises due to the misuse of accessories or parts. At the

same time, we will terminate the warranty terms of this equipment.

• This product is not intended for use by persons (including children 12

or younger) with reduced physical, sensory, or mental capabilities, or by

people who are otherwise decient in product knowledge or experience. If

such people use this product, they should be given training and be super-

vised at all times by someone responsible for their safety.

• Children ages 12 or younger should be supervised to ensure that they

do not play on or near the product.

• Maintenance and repair must be performed by trained service person-

nel only. Improper maintenance would not only damage the machine, but

also may present a danger to the exerciser.

• The user weight limit for this product is 227 kg (500 lb).

• Warning that any of the adjustment devices that could interfere with the

user’s movement should not be left projecting.

CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR

WORKOUT and consult your physician immediately. Work within your

recommended exercise level. DO NOT work to exhaustion. Before beginning

any exercise program, you should consult with your doctor. It is recommended that

you undergo a complete physical examination.

Over exercise may result in serious injury or death. If you feel faint, stop exercising

immediately.

*NOTE: Each machine provides a different resistance ratio of weight stack.

5

3. LIST OF PARTS

Assembly Parts

No. Name Qty. No. Name Qty.

A1 Weight StackFrame 1 A5 Connecting Tube 1

A2 118 Oval Foot Cover A 5 A6 Ground Fixing Bracket 2

A3 118 Oval Foot Cover B 5 A7 U Clip 2

A4 Storage Tray 1

N971

6

Components In the Hardware Kit

No. Name Qty. Specication Notes

10 Push rivets 10

L-shaped Allen wrench 1 (M6)

L-shaped Allen wrench 1 (M10)

Double open-end wrench 1 (8*17)

Double open-end wrench 1 (13.2*15.2)

19 Cap nut

Components on the Product

No. Name Specication Notes

20

Fix plate Foam included

Round head inner hex screws M8*P1.25*L15

Flat washer D17*d8.3*t2

Nylon hex nut M8

21

Round head inner hex screws M8*P1.25*L30 For A971

Spring washer M8 For A971

Flat washer D17*d8.3*t2 For A971

22

Mushroom top Phillips screw

(heat treatment)

M5*0.8*L15

Flat washer D13*d6*t1.0

7

4. ASSEMBLE THE PRODUCT

Follow instructions below to assemble this product. Note that in this manual

the words “left” and “right” are used to refer to the product and its parts. As

such, these designations correspond to the “left” and “right” sides of a person

in position to exercise on this product. Also, for brevity, the word “screws” or

“nuts” is used where washers and other hardware may be involved.

STEP 1 Install the Foot Covers

(a) Attach the oval foot covers (A2) (A3) onto the weight stack frame (A1)

legs. Align the ends and using push rivets (10) to secure the foot covers

together.

Note: If the holes don’t match up while installing the oval foot covers, change

their direction and put them back in a new way. The cutout should face the

inner side of the foot tube.

8

STEP 2 N971 Machine Assembly Instructions

To assemble N971 machine, follow the steps below.

(a) Remove screws (21) from the weight stack frame (A1).

(b) Attach the connecting tube (A5) to the weight stack frame (A1), then use

screws (21) to secure the assembly.

9

STEP 3 Install the Storage Tray

Follow the instructions below to install the storage tray.

(a) Locate the position where the storage tray (A4) attaches to the weight

stack frame (A1), then remove the screws (20) from the weight stack

frame.

(b) Attach the storage tray (A4) to the weight stack frame (A1) and use

screws (20) to secure the assembly.

10

STEP 4 Secure the Unit

Please follow the instructions (a) through (c) to secure the unit and make

sure it is firmly fixed to the floor when operating.

(a) Remove screws (22) from the ground fixing bracket (A6).

(b) Insert the U clip (A11) onto the machine (Make sure the U clip is in the

correct direction as shown below), and then secure the ground fixing

bracket (A6) with screws.

(c) Secure the ground fixing bracket to the floor with the ground fixing bolt,

nut and washer.

(Note: The screw hole of ground fixing bracket is Ø9mm, make sure you use

the suitable ground fixing bolt and drill the proper hole on the floor.)

N973

11

STEP 4 Secure the Unit (Cont.)

N971

12

*If the ground has a slight incline or is uneven, slipping some kind of shim

under one of the legs as shown below. (Several shims are given away free

enclosed with the equipment).

13

STEP 5 Cable Tension Adjustment Instructions

If the cable tension is incorrect, perform the modification adjustment: First

loosen nut A as shown then adjust nut B (as shown in the figure). Note that

if the cable is too long, adjust the nut down, and vice versa. Once the cable

reaches the desired position, tighten nut A to secure the cable length.

Note: After finished adjusting the cable, the gap between nut A and B must

be within 35mm(1.4”).

14

STEP 6 Unit Inspection

After completing the assembly or regular maintenance, please follow ins-

tructions (a) through (c) to inspect the unit. If the unit is disassembled or has

been damaged in any way, it might cause injuries or cause the unit to fail.

(a) Make sure the unit is steady and is on a level surface. If not, make ad-

justments according to the instructions “Secure the Unit” in this manual.

(b) Make sure all parts are assembled and all fasteners are tightened.

(c) Please follow operating instructions to test operation and make sure that

the equipment is working properly. (Please refer to “Operate the Product”

in this manual.)

15

5. OPERATION THE PRODUCT

This section includes operational instructions.

OPERATION Safety Operating Area

(a) Safety clearance required is shown below. Do not allow access for peo-

ple to near this area when operating.

(b) Noise emission under load is higher than without load.

(c) Over exercise or improper workout position may result in serious injury.

N973

16

N971

OPERATION Safety Operating Area (Cont.)

17

SINGLE ARM BENT ROWREVERSE FLY

CHEST FLY HIGH TO LOW ROTATION

OPERATION Exercising Instructions

a) Select the appropriate weight stacks according to your recommended

exercise level.

(b) Adjust the left/right selection frame to the most comfortable position

and make sure the knob is engaged to secure the position.

(b) Perform the exercise in a controlled manner. Inhale when pushing up

against resistance and exhale when returning to original position.

* Always workout at a level that is tolerable, to stay in the proper training

zone for your body. DO NOT work to exhaustion.

* Use equipment ONLY under the supervision of trained and qualified ins-

tructors for safety reasons.

* Please follow operating instructions on the product sticker to test opera-

tion and make sure the equipment is working properly.

18

N971

PULL-UP

OPERATION Exercising Instructions (Cont.)

19

6. MAINTENANCE

This section covers maintenance topics and includes a maintenance

schedule, task list, and log.

MAINTENANCE Safety Precautions

● Please follow standard safety precautions when servicing on this pro-

duct.

● Do NOT use a damp towel to clean the product and do perform the fol-

lowing maintenances.

● Do NOT use cleaners with alcohol, ammonia, or other damaging chemi-

cals.The use of such chemicals can damage the product and void the

warranty. Never spray or pour any liquid directly onto the product. Doing

so can damage components and void the warranty.

● Use a clean, lint-free towel, dampened with a mixture of Simple Green®all-

purpose cleaner, to thoroughly clean the handlebar and the console.

● This product has moving parts that can be hazardous. Exercise caution-

when maintaining, operating, or moving this product.

● Do not use accessories or parts that are not specically recommend-

edby the manufacturer (SportsArt) . Such parts might cause injuries or

cause the unit to fail and void the warranty. We will not be responsible

for anysafety issue that arises due to the misuse of accessories or parts.

At the same time, we will terminate the warranty terms of this equipment.

● Maintenance and repair must be performed by trained service personnel

only. Improper maintenance would not only damage the machine, but

also may present a danger to the exerciser.

● Keep this product out of use until maintenance is completed.

20

MAINTENANCE Guide Rod Cleaning and Lubricating

1. Please clean and lubricate the guide rod once a week.

(a) Use a clean, lint-free towel to apply the lubricant onto the guide rods.

(b) Test the weight stacks on the guide rod and make sure the weight

stacks move smoothly.

(c) Repeat step (a) and (b) 2-3 times.

2. Ensure proper settling of the belt tension after maintenance.

La page charge ...

SportsArt N971/N973 Le manuel du propriétaire

SportsArt N971/N973 Le manuel du propriétaire

dans d''autres langues

Documents connexes