Skil SR232301 Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

1-877-SKIL-999

OR

www.skil.com

Multi-Function Detail Sander

Ponceuse Multifonction de Précision

Lijadora de detalles multifuncional

Model/ Modelo/ Modèle: SR232301

2

TABLE OF CONTENTS

General Power Tool Safety Warnings .............................3-4

Additional Safety Warnings .....................................4-5

Symbols .....................................................6-9

Get to Know Your Multi-Function Detail Sander ....................10

Specications .................................................10

Operating Instructions .......................................11-16

Maintenance ...................................................17

Extension Cords ...............................................18

Troubleshooting ...............................................18

Limited Warranty of Skil Consumer Portable,

Benchtop and Hd and Shd Heavy Duty Power Tools ..................19

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

3

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

4

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool

in unexpected situations.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

ADDITIONAL SAFETY WARNINGS

Unplug the sander before changing accessories. Accidental start-ups may occur if sander

is plugged in while changing an accessory.

Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

5

Your tool is equipped with a dust canister, empty it frequently, after completion of

sanding and before storing the sander. Be extremely careful of dust disposal, materials in

ne particle form may be explosive. Do not throw sanding dust on an open re. Combustion

from mixture of varnishes, lacquers, polyurethane, oil or water with dust particles can occur if

there is a static discharge, spark introduced in the box, or excessive heat.

Always wear eye protection and a dust mask for dusty applications and when sanding

overhead. Sanding particles can be absorbed by your eyes and inhaled easily and may cause

health complications.

Do not wet sand with this sander. Liquids entering the motor housing is an electrical shock

hazard.

Do not use sandpaper intended for larger sanding pads. Larger sandpaper will extend

beyond the sanding pad causing snagging, tearing of the paper or kick-back. Extra paper

extending beyond the sanding pad can also cause serious lacerations.

Keep the cord away from the spinning pad and sandpaper. The cord can become entangled

with the pad.

GFCI and personal protection devices like electrician’s rubber gloves and footwear will further

enhance your personal safety.

Do not use AC only rated tools with a DC power supply. While the tool may appear to

work, the electrical components of the AC rated tool are likely to fail and create a hazard to the

operator.

Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control

the power tool.

Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful

not to disassemble any portion of the tool since internal wires may be misplaced or

pinched or safety guard return springs may be improperly mounted. Certain cleaning

agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

Risk of injury to user. The power cord must only be serviced by a SKIL Factory Service Center

or Authorized SKIL Service Station.

6

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in

foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

7

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Ø Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II tool

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

8

Symbol Name Designation/Explanation

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

9

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

10

GET TO KNOW YOUR MULTI-FUNCTION DETAIL SANDER

Fig. 1

Rubberized Grip

On/off Switch

Microlter Dust

Canister

Button for Changing Foot

Plates

Louver Attachment Finger Attachment Flexible Sanding Attach-

ment

Backing Pad

Ventilation Openings

SPECIFICATIONS

General

Model No. SR232301

Rated Input 120V, 60 Hz, 1.2A

11

OPERATING INSTRUCTIONS

WARNING

Disconnect the plug from the power source before any assembly,

adjustments or changing accessories. Such preventive safety measures

reduce the risk of starting the tool accidentally.

Backing Pad Removal/Installation

Your Multi-Function Detail sander is equipped

with a hook- and-loop rubber backing pad that

may be removed and attached without the

need for additional tools.

To remove, push the button for changing the

foot plates and pull the backing pad free from

the sander (Fig. 2).

Rotating Backing Pad

For maximum use of the sandpaper, rotate the

pad 120 degrees when the tip of the sandpaper

becomes worn (Fig. 3).

Installing Sandpaper

Your sander uses hook-and-loop backed sand-

paper, which rmly grips the backing pad when

applied with moderate pressure.

To change, merely peel off the old sandpaper,

remove any dust from the backing pad, and

press the new sandpaper in place. Be sure to

align the sanding sheet holes with the holes

in the backing pad to allow the dust extraction

system to function (Fig. 4).

Fig. 2

Fig. 3

Fig. 4

12

Mounting Special Sanding Attachments

When sanding in extremely tight areas, such as louvered panels, remove the hook-and-loop

backing pad and attach the desired attachment provided (Fig. 5). Install corresponding sand-

ing sheets to the sanding attachments.

Fig. 5

Turning the Sander On/Off

To turn on the sander, depress the side of the

On/Off switch marked “I”. To turn it off,

depress the side of the On/Off switch marked

“O” (Fig. 6).

Fig. 6

13

Microlter Dust Canister

The integrated dust extraction system collects sanding dust in the canister supplied with your

sander. For maximum efciency, the dust canister should be emptied frequently during opera-

tion.

WARNING

Your tool is equipped with a dust canister; empty it frequently during

use, after completion of sanding, and before storing the sander. Be

extremely careful of dust disposal; materials in ne particle form may be explosive. Do not

throw sanding dust on an open fire. Combustion from mixture of varnishes, lacquers,

polyurethane, oil or water with dust particles can occur if there is a static discharge, spark

introduced in the box, or excessive heat.

Installing and Removing Dust

Canister

WARNING

Always disconnect the plug

from the power source

before installing or removing the dust canister.

To install the microlter dust canister, align the

slot on the dust canister with the rib on the

tool, and then push the dust canister onto the

tool until it locks into place. To remove the dust

canister, simply pull the dust canister away

from the tool (Fig.7).

Cleaning and Emptying the Dust Canister

Knock excess dust out of the microlter or remove the dust with your ngers or a soft brush (not

included). You may notice that not all the dust has come out of the canister. This will not affect

sanding performance but will reduce dust collection efciency.

NOTE: Do not wash the micro lter with soap and water. Dust may become more rmly lodged in

the pores, which will reduce dust collection, and damage the micro lter.

Sanding Tips

This tool is particularly suitable for one-handed operation and access to corners and edges that

are otherwise difcult to reach and would require hand sanding. Proles and grooves may be

nished using the tip or edge of the selected attachment.

Always be certain that smaller workpieces are securely fastened to a bench or other support.

Larger panels may be held in place by hand on a bench or sawhorses.

Fig. 7

14

SANDING: Open-coat aluminum oxide sanding sheets are recommended for most wood or metal

sanding applications, as this synthetic material cuts quickly and wears well. Some applications,

such as metal nishing or cleaning, require special abrasive pads that are available from your

dealer. For best results, use sanding and polishing accessories that are of superior quality and

are carefully selected to produce professional quality results with your sander.

The following suggestions may be used as a general guide for abrasive selection, but the best

results will be obtained by sanding a test sample of the workpiece rst.

Grit Application

Coarse For rough wood or metal sanding, and rust or old nish removal.

Medium For general wood or metal sanding

Fine For nal nishing of wood, metal, plaster and other surfaces.

Extra ne For nal sanding of bare wood, smoothing old paint, or preparing a nished sur-

face for recoating.

With the workpiece rmly secured, turn the tool

on as described above. Contact the workpiece

with the tool only after the sander has reached

its full speed and remove it from the workpiece

before switching the tool off. Operating your

sander in this manner will prolong switch and

motor life, and greatly increase the quality of

your work.

Move the sander in long steady strokes parallel

to the grain, using some lateral motion to overlap

the strokes by as much as 75%. DO NOT apply

excessive pressure — let the tool do the work.

Excessive pressure will result in poor handling,

vibration, and unwanted sanding marks (Fig. 8).

If the surface is rough, begin with coarser grits

and then complete the surfacing with medium and ne abrasives. To avoid uneven results, do not

skip more than one grit size when going from coarser to ner, and do not sand in one area for too

long. When the job is completed, gently lift the tool from the work surface and slide switch to the

“Off” position.

POLISHING: Your Multi-Function Detail sander may be tted with optional abrasive mesh or

polishing pads to polish or remove scratches or corrosion from metal, painted, or other surfaces.

The tool is operated in much the same way as when sanding, but the following points should be

observed;

•

Use light pressure and a circular or overlapping motion to remove scratches and corrosion

or polish a surface.

•

If using a compound, use only as much as necessary and do not use the dust extraction

feature.

•

When working in very conned areas or louvered panels, the pad extension plate should be

used.

• Clean the bufng or mesh pads with mild detergents and warm water. DO NOT use

solvents.

Fig. 8

15

Application Advice

Use the tool with its standard backing pad for sanding large work surfaces, corners, and edges

(Fig. 9).

Fig. 9

Use the tool with special sanding attachments for hard-to-reach areas (Fig. 10).

Fig. 10

16

The exible sanding attachment is intended for

rounding edged surfaces (Fig. 11a).

The exible sanding tool can also be used on

some curved surfaces (Fig. 11b).

Fig. 11a

Fig. 11b

17

MAINTENANCE

Service

WARNING

To avoid accidents always disconnect the tool from the power supply

before cleaning or performing any maintenance.

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing internal wires and components, which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

Tool Lubrication

Your SKIL tool has been properly lubricated and is ready to use. It is recommended that tools

with gears be re-greased with a special gear lubricant at every brush change.

Carbon Brushes

The brushes and commutator in your tool have been engineered for many hours of

dependable service. To maintain peak efciency of the motor, we recommend every two to six

months the brushes be examined. Only genuine SKIL replacement brushes specially designed

for your tool should be used.

Bearings

Bearings that become noisy (due to heavy load or very abrasive material cutting) should be

replaced at once to avoid overheating or motor failure.

Cleaning

WARNING

To avoid accidents always disconnect the tool from the power supply

before cleaning or performing any maintenance. The tool may be

cleaned most effectively with compressed dry air. Always wear safety goggles when

cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not

attempt to clean by inserting pointed objects through openings.

CAUTION

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

18

EXTENSION CORDS

WARNING

If an extension cord is necessary, a cord with adequate size conductors

that is capable of carrying the current necessary for your tool must be

used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools

must use 3-wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT

ALTERNATING CURRENT TOOLS

Tool’s Ampere Rating Cord Size in A.W.G Wire sizes in mm

2

Cord length in feet

25 50 100 150

Cord length in meters

15 30 60 120

3-6

6-8

8-10

10-12

12-16

18 16 16 14

18 16 14 12

16 16 14 12

14 12 - -

0.75 0.75 1.5 2.5

0.75 1.0 2.5 4.0

1.0 2.5 4.0 -

- - - -

TROUBLE SHOOTING

Problem Cause Remedy

Tool will not start 1. Power cord is not plugged in.

2. Power source fuse or circuit

breaker is tripped.

3. Cord is damaged.

4. Burned out switch.

1. Plug tool into a power source.

2. Replace fuse or reset tripped

circuit breaker. (If the product

repeatedly causes the

circuit or fuse to trip/blow,

discontinue use immediately

and have it serviced by an

Authorized SKIL Service

Center or Service Station.)

3. Inspect cord for damage.

If damaged, have cord

replaced by an Authorized

SKIL Service Center or

Service Station.

4. Have switch replaced by an

Authorized SKIL Service

Center or Service Station.

Tool does not come up to

speed

1. Extension cord has insufcient

gauge or is too long.

2. Low house voltage.

1. Replace with adequate

extension cord (Refer to

the part of “EXTENSION

CORDS”).

2. Contact your electric

company.

19

LIMITED WARRANTY OF SKIL CONSUMER PORTABLE,

BENCHTOP AND HD AND SHD HEAVY DUTY POWER TOOLS

Chervon North America (“Seller”) warrants to the original purchaser only, that all SKIL

consumer portable, benchtop and HD and SHD Heavy Duty power tools will be free from

defects in material or workmanship for a period of one year from date of purchase. SKIL

Benchtop and consumer portable power tool models will be free from defects in material or

workmanship for a period of ninety days if the tool is used for professional use.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law,

shall be the repair or replacement of parts, without charge, which are defective in material

or workmanship and which have not been misused, carelessly handled, or misrepaired by

persons other than Seller or Authorized Service Station. To make a claim under this Limited

Warranty, you must return the complete product, transportation prepaid, to any SKIL Factory

Service Center or Authorized Service Station. For Authorized SKIL Power Tool Service

Stations, please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM

DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PRO V I NCES DO

NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE

ABOVE LIMITATION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

04/19

20

TABLE DES MATIÈRES

Avertissements de sécurité généraux

relatifs aux outils électriques ..................................21-23

Avertissements de sécurité supplémentaires .......................23

Symboles ..................................................24-27

Apprenez à connaître votre ponceuse multifonction de précision ......28

Caractéristiques techniques .....................................28

Mode d’emploi ..............................................29-34

Entretien ......................................................35

Rallonges .....................................................36

Dépannage ....................................................37

Garantie limitée des outils électriques grand public SKIL

portatifs, de table et pour usage industriel hd et shd ..............38-39

AVERTISSEMENT

•

La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres

activités liées à la construction peut contenir des produits chimiques reconnus par l’État

de la Californie comme étant la cause de cancers, d’anomalies congénitales et d’autres

problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–

Plomb provenant de peintures à base de plomb.

–

Silice cristallisée contenue dans les briques, le ciment et d’autres produits de maçonnerie.

–

Arsenic et chrome contenus dans le bois d’œuvre traité avec des produits chimiques.

•

Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous

pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :

–

travaillez dans un endroit bien ventilé;

–

munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques;

–

évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le polis-

sage, le perçage et d’autres activités liées à la construction. Portez un équipement de protection

et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant dans votre

bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent causer l’absorp

-

tion de produits chimiques dangereux.

La page charge ...

Skil SR232301 Le manuel du propriétaire

Skil SR232301 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents