FAME QUAD Series QUAD- 4150 Le manuel du propriétaire

Marque
FAME
Modèle
QUAD Series QUAD- 4150
Taper
Le manuel du propriétaire
1
QUAD Series Professional Power Amplifier
QUAD- 4150
OWNER’S MANUAL
2
Safety Information
CAUTION: To reduce the risk of electric shock, do not remove any cover(or the rear section). No user serviceable parts
inside. Refer servicing to qualified service personnel only.
WARNING: To reduce of fire or electric shock, do not expose this appliance to rain and moisture. Electrical equipments
should NEVER be kept or stored in damp environments.
This symbol, wherever appears, is intended to alert the user to the presence of un-insulated dangerous
voltage within the appliance’s enclosure that may be of sufficient magnitude to a risk of electric shock.
This symbol, wherever appears, is intended to alert the user to the presence of important operating and
maintenance (servicing) instruction in the literature accompanying this appliance.
This symbol means: indoor use only.
This symbol means: Read instructions.
3
Safety Instructions
1. Read Instructions à All the safety and operating instructions should be read before this products is connected and
used.
2. Retain Instructions à The safety and operating instructions should be kept for future reference.
3. Heed Waning à All warnings on this appliance and in these operating instructions should be followed.
4. Follow Instruction à All operating and other instructions should be followed.
5. Heat, Water and Moisture à Do not place this appliance to close to any high heat sources such as radiators. Also
this appliance should be kept away from direct contact with liquids.
6. Ventilation à The appliance should be situated so that it’s location or position does not interfere with it’s proper
ventilation. For example, the appliance should not be situated on a sofa, bed, or similar surface that may block the
ventilation opening; or keep the appliance away of those objects such as newspapers, carpet which may cover the
ventilation opening or impede the flow of air through the ventilation opening.
7. Power Source & Power Cord à This appliance should be connected to a power supply only of the type described
in these operating instructions, or marked on the unit.
Be sure connect the appliance to a mains power socket which with a protective grounding connection.
Power supply cord should be routed so that the are not likely to be walked upon or pinched by the items placed on or
against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not
by pulling on the cord.
Check the total maximum power of your AC wall outlet and make sure it has the enough power to match the Power
Consumption of this appliance, otherwise you could overload the wall outlet, which could cause fire.
8. Internal / External Voltage Selectors à Internal of external voltage selector switches, if any, should only be reset
and re-equipped with a proper plug for alternative voltage by a qualified service technician . Do not attempt to alter this
yourself.
9. Object & Liquid Entry à Take care to avoid any objects falling into or liquids are not spilled in to the inside of the
appliance.
10. Cleaning à Unplug the appliance first and clean only with a dry cloth.
11. Non-use Period à The power cord of the appliance should be unplugged from the outlet when left unused for long
periods of time.
12. Unpacking & Setup à Please check your appliance for any damage after unpacking(before connecting) and
contact your dealer in case of any related complains. Take care of choosing your installation place and the correct AC
connection. If built in to a case, be aware that the depth and the weight of some kind appliance(such as Amplifier) does
require an additional fixing on the backside or the use of rack shelf supports. Never mount the amplifier in a rack just
by fixing it on the front plate – Manufacturer takes no responsibility in this case.
13. Damage Requiring Service à Servicing is required when the appliance has been damaged in any way, such as
power cord or plug is damaged, liquid has been spilled or objects have fallen in the appliance, the appliance has been
exposed to rain or moisture, does not operate normally, or has been dropped. Refer all servicing to qualified service
personnel or contact your dealer. Do not attempt to repair by yourself.
4
Front panel:
1. Power ON/OFF switch
Use to turn the amplifier on and off. Amplifier will be ready for operation in a few seconds after switched ON.
2. CH-1/CH-2/CH-3/CH-4 input level control
Use to get desired input signal level.
3. CH-1/CH-2/CH-3/CH-4 protection LED (yellow)
This LED will be illuminated when amplifier under below conditions:
A. Within 3-5 second after amplifier switched On or OFF.
B. The running temperature of the power elements inside the amplifier is over 85
C. The amplifier is in singularly failure.
4. Led Bar for signal level indicating
The green ON led will be illuminated when the amplifier is turned on.
When amplifier volume exceeded maximum output level and a clipped signal already been sent to speakers, the red
PEAK led illuminated. Consistent lighting this led can cause both amplifier and speaker damaged.
5/6/7. MIX1-2, MIX2-3, MIX3-4 Input signal Link switch :
This 4 channel amplifier can be operated with maximum 4 independent input signals and by these input signal
switches, it can offers various operation modes, such as:
1 input signal & 4 outputs:
Input signal connect to CH-1 input socket, pressed all the input signal link switches. Now the amplifier can offer 4
outputs with same input signal and the input signal level only can be controlled by CH-1 Volume Pot on front panel.
2 input signals & 4 outputs:
Input 1 connect to CH-1 input socket, press the MIX1-2 switch, then this signal will be delivered to both CH-1/CH-2
for output and it volume only cab be controlled by CH-1 volume pot.
Input 2 connect to CH-3 input socket, press the MIX3-4 switch, then this signal will be delivered to both CH-3/CH-4
for output and it volume only cab be controlled by CH-3 volume pot.
Other operations are similar.
5
Rear panel
1. CH-1/CH-2/CH-3/CH-4 RCA inputs:
Use to connect unbalanced line level audio sources
2. CH-1/CH-2/ CH-3/ CH-4 XLR/JACK inputs:
Use to connect unbalanced line level audio sources
3. CH-1/CH-2/ CH-3/ CH-4 output speakon
Use to connect speakers . 1+ 2+=+, 1- 2-=-.
4. Standard Mains Power Connector (Fused)
Attention: use the correct fuse when in replacement
Specification & Technical information
MODEL
QUAD - 4150
4 x 100W
Output Powr : 8 ohm
4 ohm
4 x 150W
Input Connections
Combo & RCA with Input linkable
Output CONNECTION
4 x Speakon
Frepuency Response
20 -20KHz.-0.5dB
Input Sensitivity
1000mv
Input Impedance
20K ohm
S/N Ratio

THD

Crosstalk at rated output

Damping Factor
200
Protection
Built-in Limiter, DC Fault, AC Line Fuse, Thermal Cut
Indicator
Protect, Singal & Peak
Cooling System
No Fan / self-radiating
Mains Power Supply
AC 220V~ 50Hz
N.W(kg)
17.5
Dimension(WxDxH)mm
482x355x88
(Above data/information subject to change without perior notification)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

FAME QUAD Series QUAD- 4150 Le manuel du propriétaire

Marque
FAME
Modèle
QUAD Series QUAD- 4150
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Autres documents