1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
PowerCage 401 Enclosure • Setup Guide
This setup guide contains installation information about the PowerCage 401 Enclosure using step-by-step instructions. For
complete instructions, see the PowerCage 401 Enclosure User Guide at www.extron.com.
WARNING: Potential risk of severe injury. Installation and service must be performed by authorized personnel only.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. L’installation et l’entretien doivent être effectués
par le personnel autorisé uniquement.
Rear Panel Features
RS-232
LAN
Rx GTx
REMOTE
100-240V ~ --A MAX100-240V ~ --A MAX
50-60 Hz 50-60 Hz
RS-232
HDMI
1
2
AUDIO
AUDIO
HDMI
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx GTx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
Tx
Rx
Tx
Rx
OPTICAL
OPTICAL
INPUTS
RS-232
HDMI
1
2
AUDIO
AUDIO
HDMI
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx GTx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
Tx
Rx
Tx
Rx
OPTICAL
OPTICAL
INPUTS
RS-232
HDMI
1
2
AUDIO
AUDIO
HDMI
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx GTx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
Tx
Rx
Tx
Rx
OPTICAL
OPTICAL
INPUTS
RS-232
HDMI
1
2
AUDIO
AUDIO
HDMI
FOX DT HD
Tx
Rx
SIGNAL
HDCP
Rx GTx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
Tx
Rx
Tx
Rx
OPTICAL
OPTICAL
INPUTS
A
A
AB
B
BC
C
CD
D
DE
E
EF
FFGG
G H
H
H
Figure 1. PowerCage 401 Rear Panel
A
Power connector 1 — Connect this port to a 110-240 VAC, 50-60 Hz power source using a standard IEC power cord.
B
Power connector 2 — Connect this port to a 110-240 VAC, 50-60 Hz power source using a standard IEC power cord.
C
Slot 1 — Install a PowerCage 401-compatible board into slot 1.
D
Slot 2 — Install a PowerCage 401-compatible board into slot 2.
E
Slot 3 — Install a PowerCage 401-compatible board into slot 3.
F
Slot 4 — Install a PowerCage 401-compatible board into slot 4.
G
LAN connector — Use an RJ-45 cable to attach this connector to a LAN (Ethernet) for control of the device.
• Use a straight-through cable for connection to a switch, hub, or router.
• Use a crossover or a straight-through cable for connection directly to a PC.
H
Remote RS-232 connector — To control the unit, connect an RS-232 device to the 3-pole, 3.5 mm captive screw connector
and configure it as follows: 9600 baud rate, 8 data bits, 1 stop bit, no parity.
1
2
PowerCage 401 Enclosure • Setup Guide (Continued)
Mounting and Cabling
1. Turn off or disconnect all equipment power sources.
2. Mount the PowerCage 401 to a rack using the pre-installed MBD 149 rack ears or use the optional MBU 149 mounting kit for
under-desk mounting (see figure2).
MBD 149
Mounting Bracket
ADJUST
MENU
NEXT
RESET
POWERCAGE 401
POWER SUPPLY
POWER SUPPLY
CO
NFIG
Extron
ADJUST
MENU
NEXT
RESET
POWERCAGE 401
POWER SUPPLY
POWER SUPPLY
CO
NFIG
Extron
ADJUST
MENU
NEXT
RESET
POWERCAGE 401
POWER SUPPLY
POWER SUPPLY
CONFIG
Extron
MBU 149
Mounting Bracket
PowerCage 401
MBU 149
Mounting Bracket
Figure 2. Mounting Diagrams
NOTES:
• For tabletop mounting use the included rubber feet. Up to three units may be stacked together, one on top of the
other.
• The optional UTM 100 mounting kit may also be used to mount up to 2 units, one under the other.
3. Connect power to the rear panel IEC connector or connectors (see figure1,
A
and
B
on page1).
4. Attach cables to the LAN and RS-232 connectors, as applicable (see figure1,
G
and
H
).
Installing Transmitter and Receiver Boards into the Enclosure
Any combination of up to four transmitter or receiver boards can be installed in the PowerCage enclosure. The quantity and type
of boards vary depending on the conguration for each installation site.
Before installing the boards in the enclosure, refer to the model-specic guide for each PowerCage transmitter and receiver board
you are installing. The guides describe the features of each board and how to set up and cable it.
NOTE: The power supplies and boards are hot-swappable; they can be installed or removed without turning off or
disconnecting the power to the PowerCage 401 enclosure.
CAUTIONS:
ATTENTIONS :
• Use ESD precautions when installing a board to avoid damaging it. Keep the board in the anti-static bag until it is
needed.
• Prenez les précautions ESD lorsque vous installez une carte afin d’éviter de l’endommager. Gardez la carte dans le
sachet dépoussiérant jusqu’à ce que vous en ayez besoin.
• Use proper grounding techniques during installation.
• Utilisez des techniques de mise à la terre correctes pendant l’installation.
2
3
1. Where applicable, remove as many blank plates
or previously installed boards from the rear of the
PowerCage Enclosure as necessary to accommodate the
number of new boards to be installed.
2. Carefully slide the board into the slot, aligning the bottom
edge of the board with the left and right board mounting
slides on the bottom of the enclosure slot. Push the board
completely into the slot and finger-tighten the two top
screws while pushing in the screws to secure the board in
place. See the illustration on the following page.
3. Repeat step 2 for all boards needing installation.
NOTE: Cover all empty board slots; do not leave them
open. Securely fasten the screws for all boards and
blank panels.
RS-232
1
2
AUDIO
AUDIO
FOX DT HD
Tx
SIGNAL
HDCP
Rx
G
Tx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
OPTICAL
OPTICAL
HDMI
HDMI
Tx
Rx
Tx
Rx
Rx
OUTPUTS
RS-232
LAN
Rx GTx
REMOTE
RS-232
1
2
AUDIO
AUDIO
FOX DT HD
Tx
SIGNAL
HDCP
Rx
G
Tx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
OPTICAL
OPTICAL
HDMI
HDMI
Tx
Rx
Tx
Rx
Rx
OUTPUTS
RS-232
1
2
AUDIO
AUDIO
FOX DT HD
Tx
SIGNAL
HDCP
Rx
G
Tx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
OPTICAL
OPTICAL
HDMI
HDMI
Tx
Rx
Tx
Rx
Rx
OUTPUTS
2
A
UDIO
AUDIO
FOX DT HD
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
O
PTICAL
OPTICAL
HDMI
Rx
Tx
Rx
OUTPUTS
Screws
(2 per board)
Align board and
slide into slot.
Figure 3. Board Installation
Front Panel Features
ADJUST
MENU
NEXT
RESET
POWERCAGE 401
POWER SUPPLY
POWER SUPPLY
CONFIG
E
A
A
A
FFF
D
D
D E
E
E N
N
N O
O
O P
P
P
IIIKKK LLL MMMHHH
J
J
J
BBBBBBBCCCGGG
Figure 4. PowerCage 401 Front Panel
A
Power supply 1 LED
I
Reset button
B
Power supply 1
J
Menu button
C
Power supply 2
K
Next button
D
Fan 1
E
Fan 2
F
Configuration port
G
LCD screen
L
Horizontal adjust knob
M
Vertical adjust knob
N
Power supply 2 LED
O
Fan 3
H
Reset LED
P
Fan 4
A
Power supply 1 LED —
LED Color - State Power Supply Status Fan Status
Green - On Good Both fans functional
Red - On Failed Both fans functional
Orange - On No AC power present Both fans functional
Green - Blinking Good Either fan not functional
Red - Blinking Failed Either fan not functional
Orange - Blinking No AC power present Either fan not functional
B
Power supply 1 — Connect power to IEC power connector 1 (see figure1,
A
on page1).
C
Power supply 2 — Connect power to IEC power connector 2 (see figure1,
B
).
D
Fan 1 — For power supply 1
E
Fan 2 — For power supply 1
3
4
4
68-2640-50 Rev. B
06 20
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2016-2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
F
Configuration port — If desired, connect a host device to the front panel USB mini-B port for configuring the enclosure (see
figure4 on page3).
NOTE: This port allows communication to the enclosure and the boards.
G
LCD screen — The screen displays messages, menu information, and your selections (see Menus, Configuration, and
Adjustments).
H
Reset LED — Lights green after pressing the Reset button.
I
Reset button — Pressing the Reset button sets various enclosure settings to the factory default values.
J
Menu navigation button — Press Menu to access the PowerCage 401 menu system (see Menus, Configuration, and
Adjustments).
K
Next navigation button — From each menu press Next to step through submenus (see Menus, Configuration, and
Adjustments).
L
Horizontal adjust knob — Turn the horizontal adjust knob to navigate the menu system (see Menus, Configuration, and
Adjustments).
M
Vertical Adjust knob — Turn the vertical adjust knob to navigate the menu system (see Menus, Configuration, and
Adjustments).
N
Power supply 2 LED — See the Power Supply Status table on page3.
O
Fan 3 — For power supply 2
P
Fan 4 — For power supply 2
Menus, Configuration, and Adjustments
The PowerCage 401 enclosure has a menu system consisting of four main menus that are selected by pressing the front panel
Menu button (see figure4,
J
on page3) See the gure on previous page. Each main menu consists of submenus that are
accessed by pressing the front panel Next button (
K
). Use the front panel Horizontal (
L
) and Vertical (
M
) Adjust knobs
to make any submenu adjustments. See the following owcharts.
Power
On
60-1492-01
FW v1.00.xxx
Default
Cycle
SLOT MENU
Menu
Menu
Next
Menu
Menu
Menu
Next
2 sec.
5 sec.
2 sec.
FRAME STATUS
MENU
VIEW COMM
SETTINGS MENU
EXIT MENU
Menu
Menu
Menu
Next
Next
Extron
PowerCage 401
Default Cycle
Power
On
60-1492-01
FW v1.00.xxx
Extron
PowerCage 401
2 sec.
5 sec.
2 sec.
2 sec. 2 sec.2 sec.
SLOT MENU
Menu
Slot #1
Fox DT HD
Slot #2
N/A
Slot #3
Fox DR HD
Slot #4
N/A
-
1
-
2
-
3
-
4
dans d''autres langues
- English: Extron PowerCage 401 User manual
Documents connexes
-
Extron PowerCage 401 Manuel utilisateur
-
-
-
-
-
-
-
-
-