1
IMPORTANT:
Go to www.extron.com for the
complete user guide
, installation
instructions, and specifications.
PowerCage
®
401 FOX DT HD and
PowerCage
®
401 FOX DR HD • Setup Guide
The Extron PowerCage 401 FOX DT HD Dual Fiber Optic Transmitter and PowerCage 401 FOX DR HD Dual Fiber Optic Receiver
are modular, compact single slot boards for the Extron PowerCage 401. This guide provides instructions for an experienced
installer to install and operate both devices.
CLASS 1 LASER PRODUCT, see the PowerCage 401 FOX DT HD and PowerCage 401 FOX DR HD User Guide at
www.extron.com
WARNING: Do not look into the rear panel ber optic cable connectors or into the ber optic cables themselves.
AVERTISSEMENT: Ne regardez pas dans les connecteurs de câble bre optique sur le panneau arrière ou dans les câbles
bre optique eux-mêmes.
Installation
Board Installation
Install the transmitter, receiver, or both into a PowerCage 401
enclosure as required.
ATTENTION:
• Use ESD precautions when installing a board to
avoid damaging it. Keep the board in the
anti-static bag until it is needed. Use proper
grounding techniques during installation.
• Prenez les précautions ESD lorsque vous installez
une carte an d’éviter de l’endommager. Gardez la
carte dans le sachet dépoussiérant jusqu’à ce que
vous en ayez besoin. Utilisez des techniques de mise
à la terre correctes pendant l’installation.
NOTES:
• PowerCage boards are hot-swappable.
• Ensure the boards are ush with the rear of the enclosure and the screws are tightened securely before applying power.
• Each slot is independent from other slots. The type of board installed in a slot or the order of slots lled does not impact
boards installed in other slots.
1. If applicable, remove any blank plates or previously installed boards from the PowerCage 401 enclosure to t the board.
2. With the connectors facing away from the PowerCage 401 enclosure and the screws positioned at the top, align the bottom
board edges with the posts of the desired slots on the PowerCage 401 enclosure.
3. Carefully slide the board into the slot and push it rmly into place.
4. Tighten the screws with a tool to secure the board to the enclosure.
Device Connection
RS-232
HDMI
12
AUDIO AUDIO HDMI
FOX DR HD
Tx
Rx
Rx Rx
OPTICAL OPTICAL
Tx Tx
SIGNAL
HDCP
Rx GTx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
OUTPUTS
RS-232
HDMI
12
AUDIO AUDIO HDMI
FOX DT HD
Tx
Rx
Rx Rx
OPTICAL OPTICAL
Tx Tx
SIGNAL
HDCP
Rx GTx
RS-232
Rx GTx
Tx
Rx
SIGNAL
HDCP
INPUTS
AABB CCDD
EE EEFF
FF
Figure 1. PowerCage 401 FOX DT HD (Left) and PowerCage 401 FOX DR HD (Right) Panels
RS-232
1
2
AUDIO
AUDIO
FOX DT HD
Tx
SIGNAL
HDCP
Rx
G
Tx
RS-232
Rx
GTx
Tx
Rx
SIGNAL
HDCP
OPTICAL
OPTICAL
HDMI
HDMI
Tx
Rx
Tx
Rx
Rx
OUTPUTS
RS-232
LAN
Rx GTx
REMOTE
RS-232
1
2
AUDIO
AUDIO
FOX DT HD
Tx
SIGNAL
HDCP
Rx
G
Tx
RS-232
Rx G
Tx
Tx
Rx
SIGNAL
HDCP
OPTICAL
OPTICAL
HDMI
HDMI
Tx
Rx
Tx
Rx
Rx
OUTPUTS
RS-232
1
2
AUDIO
AUDIO
FOX DT HD
Tx
SIGNAL
HDCP
Rx
G
Tx
RS-232
Rx
GTx
Tx
Rx
SIGNAL
HDCP
OPTICAL
OPTICAL
HDMI
HDMI
Tx
Rx
Tx
Rx
Rx
OUTPUTS
2
A
UDIO
AUDIO
FOX DT HD
RS-232
Rx G
Tx
Tx
Rx
SIGNAL
HDCP
O
P
TICAL
OPTICAL
HDMI
Rx
Tx
Rx
OUTPUTS
Screws
(2 per board)
Align board and
slide into slot.
A
HDMI input connectors
B
Audio input connectors
C
HDMI output connectors
D
Audio output connectors
E
Fiber connectors
F
RS-232 connectors
2
68-2659-50 Rev. A
07 16
© 2016 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Inputs and outputs
The PowerCage 401 FOX DT HD includes two independent HDMI video inputs and two independent audio inputs. The
PowerCage 401 FOX DR HD includes two independent HDMI video outputs and two independent audio outputs.
NOTE: Use Extron LockIt
™
Lacing Bracket to secure HDMI cables to the
HDMI connectors (see the image to the right for basic instructions).
1. Connect video inputs or outputs as follows:
• For either input on the transmitter, connect a digital video source to the
HDMI input connector (see figure 1,
A
on the previous page).
• For either output on the receiver, connect a digital display to the HDMI
output connector (
C
).
2. Connect audio inputs or outputs as follows:
• For unbalanced, stereo audio input, connect an audio source to the 3.5 mm mini stereo
connector (
B
) for either input on the transmitter.
• To output unbalanced, stereo or mono audio, connect an audio output device to the 3.5 mm mini
stereo connectors (
D
) for either output on the receiver.
Throughput devices
NOTES:
• Ensure the proper ber cable is used. Typically, singlemode ber optic cables have a yellow jacket
and multimode ber optic cables have an orange or aqua jacket.
• Transmission of HDMI video with HDCP content requires a return ber optic cable from the
receiving device to the transmitting device.
1. Connect a ber cable between the Tx port on the transmitter and the Rx port on the receiver (
E
on the
previous page and the image to the right).
2. If necessary, connect a ber cable from the Tx port on the receiver to another device in one of the
following methods:
• To return serial data (such as response from a controlled device) to the transmitter, connect a cable
between the Tx port on the receiver and Rx port on the transmitter (see the image to the right).
• To connect up to ten receivers to a transmitter, connect the Tx port on the receiver to the Rx port on
another receiver (see image below) and enable daisy chain mode with SIS commands or the Product
Conguration Software (see the PowerCage 401 FOX DT HD and PowerCage 401 FOX DR HD User
Guide at www.extron.com).
Fr
om Transmitter
or Daisy-Chained
Receiver
Receiver
Receive
r
Tx
Rx
Tx
Rx
NOTE: Daisy chain mode works with non-HDCP sources only.
3. To pass serial data between a control device and a controlled device (such as control of a projector), connect the desired
type of device to the RS-232 connector on the transmitter or receiver (
F
). See the PowerCage 401 Enclosure User Guide at
www.extron.com to change the RS-232 protocol. The default RS-232 protocol is as follows:
• 9600 baud • No parity • 8 data bits
• 1 stop bit • No ow control
Operation
After all receivers, transmitters, and their related devices are connected and powered, the system is fully operational. If any
problems are encountered, verify the cables are routed and connected properly and that all display devices have identical
resolutions and refresh rates. If problems persist, call the Extron S3 Sales & Technical Support Hotline.
To congure and control the PowerCage 401 FOX DT HD and PowerCage 401 FOX DR HD, use the Extron Product Conguration
Software, Extron Simple Instruction Set (SIS™) commands, or the internal Web page with the PowerCage 401 enclosure.
3
Tip (+)
Sleeve ( )
Sleeve ( )
Ring (
-
)
Tip (+)
Audio Plugs.eps
RCA Connector
3.5 mm Stereo Plug Connector
(balanced)
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
T
ransmitter
to
Receiver
Tx Rx
Tx Rx
-
1
-
2
Extron PowerCage 401 FOX DR HD Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Extron PowerCage 401 FOX DR HD Manuel utilisateur
-
-
-
-
-
-
-
-
-