1
MACHINE OPERATION
Additional information (including troubleshooting and service) can be found in the individual chapters of
the Instructions for use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying –
at low temperatures
Suitable for tumble drying
Sort laundry by:
Material thickness: whenever there is greater load than the dryer can handle, separate
laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material: cotton (linen); synthetic textiles (easy care).
Degree of drying: cupboard dry, iron dry etc.
Do not tumble dry: nylon stockings, delicate embroidery, fabrics with metallic decorations.
Preparing laundry
Check that all fastenings are closed and that pockets are empty.
Please ensure that there are no cigarette lighters in the laundry.
Turn laundry inside out.
Loading dryer
Place laundry loosely in the drum to achieve equal drying throughout.
Then close the door.
Selecting programme
Select the drying programme required by turning the programme selector knob (for
information, refer to programme table).
If you do not start the programme soon after having made your choice, the dryer will switch
off after a few minutes.
To switch the dryer on again turn the programme selector knob to “Off” (“0”) and afterwards
to the desired programme.
Selecting options
(if available)
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking lamp indicates a wrong selection is made (incompatible options).
Press the button again to cancel the option.
Starting dryer
The drying programme is started by pressing the “Start (Pause)” button.
The relevant indicator lamp lights up.
Changing programme selection: If the programme selected is changed during drying, the
dryer stops.
The “Start (Pause)” indicator lamp flashes.
To operate the new programme, press the “Start (Pause)” button again.
Interrupting programme: To interrupt a drying cycle, press the “Start (Pause)” button
and open the door.
Wait at least 5 minutes, to allow the laundry to cool down, before you unload the dryer.
For your safety the drying cycle stops automatically if you open the door.
To restart, after door opening, close the door and press the “Start (Pause)” button again.
Warning: Never stop a tumble dryer before the end of the drying cycle, unless all items are
quickly removed and spread out so that the heat is dissipated.
Programme end –
unloading dryer
The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the
items reach a lower temperature to avoid wrinkling.
End: Take the laundry out of the dryer.
Anticrease: If the laundry is not removed at the end of the drying cycle, an automatic anti-
crease cycle will operate for maximum 15 min (by choosing the option “Anticrease” this
time can be extended up to 12 hours).
The drum rotates to prevent the laundry from creasing.
After the end of the “Anticrease” the dryer will switch off after a short time, to save energy.
Switching dryer off
Set the programme selector knob to “Off” (“O”).
Cleaning the lint filter after every cycle: open door, pull lint filter up and out of machine and open it. Brush lint using a soft brush or
your fingertips. Close door filter and push firmly back into place.
Emptying water container: pull container out by the handle and empty. Replace the container when empty by pushing it completely
back into place.
Please note: Only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which have been
provided with the garment or article.
Power consumption: In off-mode 0.065 W / in left on-mode 0.065 W.
2
Overview of programmes
Options
Approximate drying
times (in minutes)
Type of textile
Programmes / Drying levels
Fabrics
Gentle
Délicate
Anticrease
Antifroissage
plus
Rapid
Rapide
Dryness
adjustment
Niveau de
séchage
Pause
Depart
(Pause)
Key lock
Reset
Annulation
Finish in
Heure
de fin
Very
wet load Wet load
Cotton
W
Séchage renforcé
Extra dry
Multi-layered, thick laundry such as: terry towels, terry
towelling bath robes.
Cotton or linen hot wash /
coloured laundry
Max. 9.0 kg
X X X X X X X X 225 200
Prêt à ranger
Cupboard dry +
Terry towels, dry towels, bed linen, underwear
X
X
X
X
X
X
X
X
205
180
Prêt à porter
Cupboard dry*
Similar types of laundry which do not require ironing such
as: dry towels, bed linen, underwear, baby clothes,
T-shirts, cotton socks.
X X X X X X X X 185 160
Prêt à repasser
Iron dry*
Laundry which requires ironing such as: bed and table
linen, dry towels, T-shirts, polo shirts, work clothes.
X X X X X X X X 150 130
Synthetic
VW
Prêt à ranger
Extra dry
Laundry with thick, multi-layered areas such as: bed and
table linen, track suits, anoraks, blankets.
Synthetic, mixed fibre or
cotton easy care
(ironing not required)
laundry
Max. 4.5 kg
X X – X X X X X 100 75
Prêt à porter
Cupboard dry*
Laundry which does not require ironing such as: shirts,
blouses, T-shirts, sportsware.
X X – X X X X X 75 60
Prêt à repasser
Iron dry
Laundry which requires ironing such as: trousers, dresses,
skirts, shirts, blouses.
X X – X X X X X 65 55
Special programmes
V
Delicate plus
Low drying intensity for delicates and items such as:
trousers, dresses, shirts, blouses.
Laundry made from
synthetic fibres such as
polyamide, nylon,
polyacrylic, etc.
2.5 kg
X X – – X X X X 105 90
Mixed load
T-shirts, blouses, towels, underwear, sportswear.
Cotton – synthetic blend
3.0 kg
X X – X X X X X 85 70
Jeans
Jeans, working trousers and jackets.
Cotton
3.0 kg
X X – X X X X X 110 95
Silk
Blouses, shirts and T-shirts.
Textiles made of silk
2.5 kg
X X – – X X X X 105 90
Sport
Sport clothes, functional underwear, running tights.
Synthetic
2.5 kg
X X – – X X X X 105 90
Airing
Laundry is aired, refreshed and loosen up for 30
minutes without heating.
All textiles.
– – – – X X X X 30’ –
Drying
items
Completes drying (suitable for all fabrics)
10’ – 120’
X X X – X X X X 10’ – 120’
*Test programmes according to EN61121, tested with maximum rated load capacity.
3
HOW TO PROCEED IF…
...you want to check the dryer yourself first:
(If your machine is not functioning correctly, please check the
following points before calling the customer service
– also refer to relevant chapter in the Instructions for use)
Drying takes too long /
Laundry is not dry
enough
• Has the correct drying programme been selected?
• Has the cycle been interrupted (door opening, full water container)?
• Was the inserted laundry too wet (washing machine spin speed less
than 1000 rpm)?
• Is the lint filter dirty (filter indicator light on)?
• Is the heat exchanger dirty (for more information, refer to the
Instructions for use)?
• Is the room temperature too high?
• Is the “End” and “Anticrease” indicator lamp lighting up?
The drying cycle is complete and the laundry can be taken out.
•
If the drying result does not meet your expectation, select a more dry
programme or use the dryness adjustment option (if available) to
optimize the drying result.
• Is thin and thick load mixed? Are different types of materials mixed?
Sort the laundry after thickness and material and dry again.
The dryer does not
operate (after a power
failure, always press
the “Start (Pause)”
button)
• Is the plug properly inserted into the mains electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has a drying programme been selected?
• Has the “Start (Pause)” button been pressed shortly after a
programme is selected? (If not, the dryer will switch off.)
• Has the start delay option been selected?
• Is the dryer overloaded? Please remove a part of the load.
Filter, water container
indicator lamp on
• Is the lint filter clean?
• Is the water container empty?
• Has the water container been inserted correctly?
• Is the heat exchanger clean and inserted correctly?
Water droplets
underneath the dryer
• Has the heat exchanger been inserted correctly?
• Have all lint on the heat exchanger seal and the door seal been
wiped away?
• Has the water container been inserted correctly?
• If the direct drain connection is used, is it tight?
• Is the dryer leveled?
...you want to
care of and clean your dryer:
Clean the filter at the
end of every cycle
• Brush lint using a soft brush or your fingertips.
• Close the filter.
• Push the filter back into place.
Empty the water
container at the end of
every drying cycle
• Pull the handle to remove the water container.
• Empty the water container.
• Replace the water container when empty by pushing it completely
back into place.
Clean the heat
exchanger at least
once a month
• Clean the heat exchanger under running water.
• Remove all fluffs from the seals.
• Clean the heat exchanger housing (for further information see
chapter “Cleaning the heat exchanger” in the Instructions for use).
4
FAILURE CODES
In case of a
malfunction of the dryer, one the following failure codes could be displayed.
Depending on the model of your dryer, the failure can be displayed in letters or by different blinking lamps.
Failure
code
Lamps failure code
Check needed by customer before
Service call
F01
Please call the After-Sales-Service.
F02
Please call the After-Sales-Service.
F03
Please call the After-Sales-Service.
F04
Please call the After-Sales-Service.
F05
Turn OFF the dryer.
Unplug the dryer.
Assure that the ambient temperature is
between 5°C and 35°C.
Wait for 1 hour.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
F06
F07
F10 – F22
Turn OFF the dryer.
Unplug the dryer.
Wait for 30 minutes.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
Start lamp is blinking 2 times per second when it is pressed
Assure that the door is correctly closed and
heat exchanger correctly positioned.
Heat exchanger lamp is blinking 2 times when the Start
button is pressed
Assure that the heat exchanger is correctly
positioned.
5
Before using the machine, please also read the instructions for use carefully!
AZB 9785 – Quick Reference Guide
Indicator lamps and Options
Programme selector knob
The drying programme is
selected by turning
this knob.
The “Start (Pause)” indicator lamp flashes.
“Start (Pause)” button
The drying programme is s
tarted by pressing
this button.
The indicator lamp lights up.
Filter
The indicator lamp lights up when the filter
and/or heat exchanger including housing
needs to be cleaned.
Clean the filter at the end of every
drying cycle.
Water container
The indicator lamp lights up when the water
container needs to be emptied.
The drying cycle is automatically interrupted.
Empty the container and restart the drying
programme.
Empty the water container after every
drying cycle
Clean heat exchanger
The Led lights up after 30 cycles when the
heat exchanger needs to be cleaned.
Clean the heat exchanger.
“Remaining time” display
Depending on the programme selected a
de
fault drying time is displayed.
After start of cycle the time displayed is
corrected depending on the volume, type
and moisture of the laundry.
The drying time specified is a calculated
value which will be updated during the
drying cycle.
The flashing lines indicate t
hat the calculation
is running.
The remaining time will be updated.
Eco Monitor
The
“Eco monitor” gives you a rough
feedback about the energy consumption of
the humidity steared programmes.
As soon as you turn the programme selector
to any humidity steared programme, the
“
Eco monitor” lamps will indicate the
expected energy consumption.
The three indicators show the degree of
consumption: the less energy your
programme setting is forecasted to consume,
the less indicators will light up.
This depends on the programme, in
itial
moisture and options selected, and also on
the size of the load.
For that reason, the forecasted degree of
energy consumption may adapt when the
tumble dryer detects the load size.
End
Th
e drying programme is finished.
Please unload the dryer.
Overdry protection / 6th Sense
The indicator lights up when a humidity
controlled programme is selected, to indicate
the activated protection function.
6
Dryness level
By selecting this option you can adjust the
dryness level of the laundry.
After
the selection of the desired programme
you can choose the dryness level by pressing
the button.
Pressing 1 time you select a more dry level
or
Pressing 2 times you select a less dry level
or
Pressing 3 times you select again normal dry
level
.
Reset
During the selection phase of the
programme, pressing this button will switch
off all settings of selected options.
During
running drying cycle the pressing of
the button will stop the cycle and set the
dryer back in selection mode.
The button needs to be pressed for
3 seconds.
Key lock
For child protection reasons, this option can
be used to lock all functions of the user
interface.
To activate this option, the button needs to
be pressed for 3 seconds, until the
“key”
symbol at t
he display appears.
To deactivate this option, press the button
until the
“key” symbol disappears.
The key lock function is still active even when
the selector knob is turned to
“off” “0”
position or the door is opened.
The function has to be deactivated.
Dry time adjustment
Turn the programme selector knob to
“Drying Time”
position.
Press the button
“Drying time” to select the
duration of cycle in ten minutes steps up to
12
0 minutes.
Gentle
Selecting this option will
reduce the drying
temperature.
This option cannot be selected when the
option “Rapid” is selected.
Rapid
Selecting this option reduces the drying time.
This option should only be selected for cotton
programmes, with a maximum load of 3.5 kg.
The garments shall have similar size and
thickness.
Anticrease
This option can be chosen to reduce
wrinkling, when the laundry is not unloaded
d
irectly after end of the cycle.
The drum turns from time to time for
maximum 12
hours.
It can be interrupted at any t
ime by switching
off the dryer.
This option deactivates the
“Buzzer”
function, if it is activated.
Finish in
With this function you can postpone your
programme to complete at a later time: press
the button to select in how many hours the
programme shall be finished.
•
Thus, it allows you to have your laundry
ready at a particular time and to profit
from more favorable energy rates during
the night, for example.
•
The “Finish in” function can be selected
in full hour time segments (1 to 24 h).
When you press the button, the shortest
possible time will be displayed; keep on
pressing the button to loop through all the
available times.
To remove it again, set the index of
the programme selector knob to the
“Off” “(0)” position.
•
When you have selected the desired
“Finish in” time, press “Start” – the
countdown will begin.
•
During the countdown, you can still
modify the option setting (select or
deselect options).
•
Sometimes the programme may finish
before the selected “Finish in” time has
expired (e.g. for small loads).
In this case, the dryer will tumble the
laundry regularly to keep it fresh, until the
selected “Finish in” time has expired.
During tumbling, the display will show an
animation.
The tumbling phase can be stopped at
any time either by pressing any button,
by rotating the programme selector or
by opening the door.
5019 300 00633
(Subject to technical modifications)
-
1
-
2
-
3
-
4
-
5
-
6
