B&B Electronics McPc-Gigabit Mode d'emploi

B&B Electronics
Marque
B&B Electronics
Modèle
McPc-Gigabit
Catégorie
Convertisseurs de média réseau
Taper
Mode d'emploi
McPC-Gigabit
(PCI Version)
Operation Manual
ii
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable
solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any other
liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third party
except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the products,
including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have
been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions, illustrations, figures
as to performance, drawings and particulars of weights and dimensions contained in the B&B Electronics’ catalogs, price
lists, marketing materials or elsewhere since they are merely intended to represent a general idea of the products and do
not form part of this price quote and do not constitute a warranty of any kind, whether express or implied, as to any of the
B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED
IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE
INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE LIABLE FOR
LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL
DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY
OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF
B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.
iii
Table of Contents
FCC Radio Frequency Interference Statement .................................................... ii
Limited Lifetime Warranty .................................................................................. ii
About the McPC-Gigabit .................................................................................... 1
AutoCross .......................................................................................................... 1
LED Indicators .................................................................................................... 2
Specifications ..................................................................................................... 2
B&B Electronics Technical Support ..................................................................... 3
Fiber Optic Cleaning Guidelines ......................................................................... 3
Electrostatic Discharge Precautions ..................................................................... 4
Certifications ...................................................................................................... 5
1
About the McPC-Gigabit
The McPC-Gigabit is a low-cost, IEEE 802.3 single-conversion, PC Card media
converter that converts 1000Base-TX twisted pair to 1000Base-SX multi-mode or
1000Base-LX single-mode fiber. The McPC-Gigabit is available with one RJ-45
connector for the twisted pair port and a SC connector for the fiber port.
The McPC-Gigabit is also available for single-strand which allows two individual
channels to share one strand of fiber; Full-Duplex data travels on different
wavelengths— 1310 nm and 1550 nm.
The McPC-Gigabit can be mounted into any PC with a standard PCI and includes
diagnostic LEDs for each port.
Installing the McPC-Gigabit
Offering plug-and-play operation, the McPC-Gigabit comes ready to install, utilizing
power from the PC’s motherboard. To install the McPC-Gigabit:
1.
Turn off the PC
2.
Remove its cover
3.
Find an empty PCI slot
4.
Align the McPC-Gigabit in the slot
5.
Screw the McPC-Gigabit into the computer casing’s bracket
6.
Make sure the McPC-Gigabit does not extend past the edge of the case
7.
Attach the keyed mini-power connector to the McPC-Gigabit
8.
Attach the male end of the “Y” connector to one of the computer’s standard size
power connectors
9.
Replace the cover
10.
Attach the cables between the McPC-Gigabit and the devices that will be
connected
AutoCross
Whether you are using crossover or straight-through CAT5 twisted pair cabling,
McPC-Gigabit will support both types of connections with
AutoCross
, a feature which
automatically selects between a crossover workstation or Pass-Through connection
depending on the connected device.
FX
TX
2
LED Indicators
Each McPC-Gigabit includes two LEDs, located on the RJ-45 connector.
LED functions are as follows:
FX LNK/ACT Glows green when a link is established on the fiber port;
blinks
green when activity is detected on the fiber port.
TX LNK/ACT Glows amber when a link is established on the
copper port;
blinks
amber when activity is detected on the copper port.
Specifications
Environmental
Operating Temperature
+32° to +104° F (0° to +40° C)
Storage Temperature
-4° to +158° F (-20° to +70° C)
Humidity:
5 - 95% (non-condensing)
Input Specifications
0.7A @ 5V DC
3
B&B Electronics Technical Support
Tel:
(800) 346-3119 (in the U.S. and Canada)
Monday-Friday, 7:00am-7”00pm CST
+353 91 792444 (Europe)
Monday through Friday 8:00am - 5:00pm GMT
Fax:
(815) 433-5109 U.S. and Canada
+353 91-79244S5 Europe
E-Mail:
[email protected] U.S. and Canada
[email protected] Europe
Web:
www.bb-elec.com
Fiber Optic Cleaning Guidelines
Fiber Optic transmitters and receivers are extremely susceptible to contamination by
particles of dirt or dust, which can obstruct the optic path and cause performance
degradation. Good system performance requires clean optics and connector ferrules.
1.
Use fiber patch cords (or connectors, if you terminate your own fiber) only from
a reputable supplier; low-quality components can cause many hard-to-diagnose
problems in an installation.
2.
Dust caps are installed at B&B Electronics to ensure factory-clean optical devices.
These protective caps should not be removed until the moment of connecting
the fiber cable to the device. Should it be necessary to disconnect the fiber
device, reinstall the protective dust caps.
3.
Store spare caps in a dust-free environment such as a sealed plastic bag or box so
that when reinstalled they do not introduce any contamination to the optics.
4.
If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to remove
particles of dirt.
4
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) can cause damage to any product, add-in modules or
stand alone units, containing electronic components. Always observe the following
precautions when installing or handling these kinds of products
1.
Do not remove unit from its protective packaging until ready to install.
2.
Wear an ESD wrist grounding strap before handling any module or component.
If the wrist strap is not available, maintain grounded contact with the system unit
throughout any procedure requiring ESD protection.
3.
Hold the units by the edges; do not touch the electronic components or gold
connectors.
4.
After removal, always place the boards on a grounded, static-free surface, ESD
pad or in a proper ESD bag. Do not slide the modules or stand alone units over
any surface.
W
A
RNING!
Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.
5
Certifications
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC). For further details, contact B&B
Electronics.
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
International Headquarters
B&B Electronics
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 — General Fax (815) 433-5105
Email: [email protected]
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 — Fax +353 91-79244S5
Email: techSupport@bb-elec.com
Website: www.bb-elec.com
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any
errors that may appear in this document. McPC-Gigabit is a trademark of B&B Electronics. Other brands or product
names may be trademarks and are the property of their respective companies.
Document Number 55-80900-00 B1 September 2013
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

B&B Electronics McPc-Gigabit Mode d'emploi

B&B Electronics
Marque
B&B Electronics
Modèle
McPc-Gigabit
Catégorie
Convertisseurs de média réseau
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents