901049-00NC 1
IHP.us.com
BURNER REPLACEMENT INSTRUCTIONS FOR COMPASS, COMPASSDLX, DRL2000 & DRL3500 SERIES
KIT COMPONENTS
Burner, Instruction Sheet
REQUIRED TOOLS AND SUPPLIES
Safety Gloves, Adjustable Wrench, Channel Locks, Pliers, 5/16” Nutdriver,
1/4” Nutdriver or wrench.
TURN OFF THE GAS SUPPLY TO THE APPLIANCE. DISCONNECT
ELECTRICAL POWER SUPPLY.
READ ALL THE STEPS BEFORE STARTING THE CONVERSION. IN-
STALLER NOTICE: THESE INSTRUCTIONS MUST BE LEFT WITH THE
APPLIANCE.
When installing gas components use pipe joint compound or
Teflon tape on all pipe fittings before installing (Do not use pipe
joint compounds on flare fittings).
NOTE: THE FIREPLACE MUST BE OFF AND COLD BEFORE PERFORM-
ING THE GAS CONVERSION.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL-
LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE
APPLY TO THESE INSTRUCTIONS.
GENERAL INFORMATION
This kit contains all the necessary components needed to complete
the task and to ensure a safe operation.
WARNING
This burner replacement kit shall be installed by
a qualified service agency in accordance with the
manufacturer's instructions and all applicable codes
and requirements of the authority having jurisdiction.
If the information in these instructions is not followed
exactly, a fire, explosion or production of carbon mon-
oxide may result causing property damage, personal
injury or loss of life. The qualified service agency
performing this installation is responsible for the
proper installation of this kit and assumes respon-
sibility for this burner replacement. The installation
is not proper and complete until the operation of the
appliance is checked as specified in the manufacturers
instructions supplied with the appliance.
IMPORTANT LE CANADA SEULEMENT
Cet remplacement du brûleur devra être effectuée
conformément aux recommandations des autorités
provinciales ayant juridiction et conformément aux
exigences du code d'installation CAN/CSA B149.1.
IMPORTANT CANADA
This burner replacement shall be carried out in accor-
dance with the requirements of the provincial authorities
having jurisdiction and in accordance with the require-
ments of the CAN/CSA B149.1 Installation code.
AVERTISSEMENT
Cet équipement de remplacement du brûleur sera
installé par une agence qualifiée de service con-
formément aux instructions du fabricant et toutes
exigences et codes applicables de l'autorisés avoir
la juridiction. Si l'information dans cette instruction
n'est pas suivie exactement, un feu, explosion ou
production de protoxyde de carbone peut résulter le
dommages causer de propriété, perte ou blessure
personnelle de vie. L'agence qualifiée de service
est esponsable de l'installation propre de remplace-
ment du brûleur. L'installation n'est pas propre et
compléte jusqu'à l'opération de l'appareil est chéque
suivant les critères établis dans les instructions de
propriétaire provisionnées avec l’appareil.
REPLACEMENT INSTRUCTIONS
P/N 901049-00
Rev. NC, 03/2020
HEARTH PRODUCTS
KITS AND ACCESSORIES
IHP.us.com 901049-00NC2
INSTALLING THE BURNER INSTRUCTIONS
CAUTION
The gas supply shall be shut OFF prior to discon-
necting the electrical power, before proceeding
with the conversion.
ATTENTION
Avant d’effecteur la conversion, coupez d’abord
l’alimentation en gaz, ensuite, coupez l’alimentation
electrique.
Step 1. Remove the screws in perforated media floor and remove.
Step 2. Remove the screw in the burner and slide to the right to remove
(taking care not to bend air shutter adjustment rod).
1. TURN OFF THE GAS SUPPLY TO THE FIREPLACE. Disconnect
power supply at the circuit breaker. Ensure fireplace is cold.
2. Remove the barrier assembly, facade, and glass door per in-
struction in the Installation and Operation Manual.
3. If applicable: Remove the facade and lower compartment cover
for easier access.
4. If applicable: Remove the Media (including glass, porcelain pan-
els, logs & rocks).
5. Perform the following burner replacement instructions:
Figure 1 Figure 2
Step 3. Remove air shutter adjustment rod and air shutter from original
burner. (Seen in Figure 3, page 3) using a 1/4” nutdriver or wrench. Install
the removed air shutter and adjustment rod on new burner. Place the bent
portion of the air shutter adjusting rod in the slot from the left side of the
shutter arm (See Figure 2). Carefully lower the air shutter adjustment rod
thru hole in firebox floor while sliding the burner to the left and replace
burner attachment screw (left side of burner) [Note: Burner has L shaped
flanges that will install in the burner support brackets].
Step 4. Before reinstallation of the perforated media floor, verify the pilot
to burner relationship. Page 3, figure 6.
Step 5. Reinstall any media and panels that were removed. Refer to instal-
lation manual and/ or instruction sheets for proper placement/ installation.
Step 6. Reinstall the glass door.
Step 7. Turn on gas supply and test for gas leaks, using a gas leak test
solution—also known as bubble leak solution.
Step 8. Adjust the burner air shutter. See Burner Air Shutter Adjustment
Instructions Section on page 3 and Table 1 and Figures 2 and 3.
CAUTION: The air shutter should never be set so as to make the tips
of the flames sooty or create sooting on the viewing glass, logs, or
media. If soot begins to form after burning, the air shutter should be
opened gradually until the sooting condition stops. Gas quality and gas
pressure may vary, which can affect the burning characteristics of the
appliance.
WARNING
Never use an open flame to check for leaks.
Air Shutter Rod
Air Shutter
901049-00NC 3
IHP.us.com
BURNER AIR SHUTTER ADJUSTMENT INSTRUCTIONS
1. Adjust the air shutters per instructions in Figure 3 and Table 1.
2. Light the fireplace. Follow the lighting procedure on the lighting label in
the control compartment.
3. Allow the burner to operate for at least fifteen (15) minutes while
observing the flame continuously to ensure that the proper flame
appearance is achieved (Figure 4). If the following conditions are
present, adjust accordingly.
• If flame appears weak or sooty, adjust the air shutter, incrementally,
to a more open position until the proper flame appearance is
achieved.
• If flame remains blue, adjust the air shutter, incrementally, to a
more closed position until the proper flame appearance is achieved.
Burner Air Shutter Settings
Models Natural Gas Propane/LP Gas
All 1/4”
(6.4 mm)
1/2”
(13 mm)
Table 1
Figure 4 - Burner Flame Appearance
Figure 3 - Air Shutter Setting
No Blue Flame
Center
Soot at
Flame Tip
Dark Orange
Flame
IMPROPERLY
BURNING FLAME
Soot above
Flame Tip No Soot at
Flame Tip
PROPERLY
BURNING FLAME
Semi-Transparent
Yellow Flame
Blue Flame
Center
Air Shutter
Adjustment
Rod Down
(Fully-Open
Position)
Burner
Tube
Adjustment
Rod Up
(Fully-Closed
Position)
Adjustment
Set-Screw
The adjustment rod for the front air shutter is
located in the lower control compartment. See
Table 1 for the standard adjustment setting.
Closed
Open
Figure 5 - Pilot Flame Appearance
Pilot
Hood
Sensor
Ignitor
Igniter
Pilot Hood
Thermocouple
Pilot Hood
Thermocouple
Igniter
Figure 6 - Ensure Proper Alignment Between Pilot And Burner
Burner
Pilot Hood
1/4” + .00”
- .06”
4
Printed in U.S.A. © 2020 Innovative Hearth Products
P/N 901049-00 Rev. NC 03/2020
Innovative Hearth Products (IHP) reserves the right to make changes at any time, without notice,
in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
1769 East Lawrence Street • Russellville, AL 35654
-
1
-
2
-
3
-
4
Astria Fireplaces DRL30 Instruction Sheet
- Taper
- Instruction Sheet
dans d''autres langues
- English: Astria Fireplaces DRL30