LG DLEX2550N Le manuel du propriétaire

OWNER’S MANUAL

DRYER

DLEX2550* DLGX2551*

DLEX2450* DLGX2451*

DLEX2650* DLGX2651*

DLEX2655* DLGX2656*

Please read this manual carefully before operating

your dryer and retain it for future reference.

P/No. MFL67408112

www.lg.com

ENGLISH

FRANÇAIS

IMPORTANT SAFETY INSTRUCTIONS

What to Do if You Smell Gas .................................. 3

Basic Safety Precautions ....................................... 4

California Safe Drinking Water and Toxic

Enforcement Act ................................................... 4

Grounding Instructions ...........................................5

Safety Instructions for Installation ..........................5

Safety Instructions for Steam Functions ................6

Safety Instructions for Connecting Electricity .......7

Congratulations on your purchase

and welcome to the LG family. Your

new LG Dryer combines the most

advanced drying sensor technol-

ogy with simple operation and high

efficiency.

Follow the operating and care in-

structions in this manual and your

dryer will provide many years of reli-

able service

THANK YOU!

INSTALLATION INSTRUCTIONS

Installation Location Requirements ..................... 10

Clearances ........................................................... 10

Installation With Optional

Pedestal Base or Stacking Kit .............................. 11

Leveling the Dryer ................................................ 12

Optional Accessories .......................................... 12

To Remove the Door ............................................ 13

To Install the Door ............................................... 14

Changing the Dryer Vent Location ....................... 15

Venting the Dryer .................................................. 16

Connecting Gas Dryers ........................................ 18

Connecting Electric Dryers .................................. 20

Special Requirements for Manufactured

or Mobile Homes ................................................. 25

Final Installation Check ....................................... 25

Installation Test (Exhaust check) ......................... 26

HOW TO USE

Control Panel Features ........................................ 28

Operating the Dryer ............................................. 29

Cycle Guide ......................................................... 30

Sorting Loads ...................................................... 3 1

Loading the Dryer ................................................ 3 1

Check the Lint Filter Before Every Load .............. 3 1

The Display .......................................................... 32

Cycle Setting Buttons .......................................... 33

Special Functions ................................................ 34

Custom Program ................................................. 35

Steam Functions .................................................. 35

Steam Cycle Guide .............................................. 37

TROUBLESHOOTING

Regular Cleaning ................................................ 38

Before Calling for Service ....................................39

Using SmartDiagnosis

TM

.......................................42

PARTS AND FEATURES

Special Features ..................................................... 8

Key Parts and Components ................................... 9

OPTIONAL ACCESSORIES

Optional Accessories ........................................... 43

Pedestal Installation ............................................. 44

Stacking Kit Installation ........................................ 46

SPECIFICATIONS

Key Dimensions and Speciﬁcations ..................... 47

WARRANTY ................................................... 48

2

ENGLISH

1. Do not try to light a match or cigarette,

or turn on any gas or electrical

appliance.

2. Do not touch any electrical switches.

Do not use any phone in your building.

3. Clear the room, building, or area of all

occupants.

4. Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

5. If you cannot reach your gas

supplier, call the ﬁre department.

WHAT TO DO IF YOU SMELL GAS:

3

READ ALL INSTRUCTIONS BEFORE USE

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read

and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.

wWARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of

injury, and tell you what can happen if the instructions are not followed.

•Donotinstallaclothesdryerwith

ﬂexible plastic venting materials. If

ﬂexible metal (foil type) duct is in-

stalled, it must be of a speciﬁc type

identiﬁed by the appliance manufac-

turer as suitable for use with clothes

dryers. Flexible venting materials are

known to collapse, be easily crushed,

and trap lint. These conditions will

obstruct clothes dryer airﬂow and

increase the risk of ﬁre.

•Donotstoreorusegasolineorother

ﬂammable vapors and liquids in the

vicinity of this appliance or any other

appliances.

•Installationandservicemustbe

performed by a qualiﬁed installer,

service agency, or the gas supplier.

•Installtheclothesdryeraccordingto

the manufacturer’s instructions and

local codes.

•Savetheseinstructions.

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, injury to persons , or death.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING

For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, injury to persons , or death.

CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT

This act requires the governor of California to publish a list of substances known to the state to cause

cancer, birth defects, other reproductive harm and requires businesses to warn customers of potential

exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

BASIC SAFETY PRECAUTIONS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Readallinstructionsbeforeusingthedryer.

•Beforeuse,thedryermustbeproperlyinstalled

as described in this manual.

•Donotplaceitemsexposedtocookingoilsin

your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that

could cause a load to catch ﬁre.

•Donotdryarticlesthathavebeenpreviously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂammable or explosive substances as they give

off vapors that could ignite or explode.

•Donotreachintothedryerifthedrumorany

other part is moving.

•Donotrepairorreplaceanypartofthedryer

or attempt any servicing unless speciﬁcally

recommended in this Use and Care Guide or

in published user-repair instructions that you

understand and have the skills to carry out.

•Donottamperwithcontrols.

•Beforethedryerisremovedfromserviceor

discarded, remove the door to the drying

compartment.

•Donotallowchildrentoplayonorinthedryer.

Close supervision of children is necessary when

the dryer is used near children.

•Donotusefabricsoftenersorproductsto

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

•Donotuseheattodryarticlescontaining

foam rubber or similarly textured rubber-like

materials.

•Keepareaaroundtheexhaustopeningand

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

•Theinteriorofthedryerandexhaustvent

should be cleaned periodically by qualiﬁed

service personnel.

•Donotinstallorstorethedryerwhereitwillbe

exposed to the weather.

•Alwayschecktheinsideofthedryerforforeign

objects.

•Cleanlintscreenbeforeoraftereachload.

•Donotstoreplastic,paper,orclothingthat

may burn or melt on top of the dryer during

operation.

4

ENGLISH

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event

of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing

a path of least resistance for electric current.

This appliance must be equipped with a cord

having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into

an appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

Do not modify the plug provided with the

appliance. If it will not ﬁt the outlet, have a proper

outlet installed by a qualiﬁed electrician.

This appliance must be connected to a grounded

metal, permanent wiring system or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

Electric shock can result if the dryer is not

properly grounded.

wWARNING — Improper connection of the equipment-grounding conductor can result

in a risk of electric shock. Check with a qualiﬁed electrician or service person if you are in doubt that the

appliance is properly grounded.

5

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

•Properly ground dryer to conform with all

governing codes and ordinances. Follow

details in the installation instructions. Electric

shock can result if the dryer is not properly

grounded.

•Before use, the dryer must be properly

installed as described in this manual. Electric

shock can result if the dryer is not properly

grounded.

•Install and store the dryer where it will not be

exposed to temperatures below freezing or

exposed to the weather.

•All repairs and servicing must be performed

by an authorized servicer unless speciﬁcally

recommended in this Owner’s Guide. Use

only authorized factory parts. Failure to follow

this warning can cause serious injury, ﬁre,

electric shock, or death.

•To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to

follow this warning can cause serious injury, ﬁre,

electric shock, or death.

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, injury to persons , or death.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Connect to a properly rated, protected,

and sized power circuit to avoid electrical

overload. Improper power circuit can melt,

creating electric shock and/or ﬁre hazard.

•Remove all packing items and dispose of all

shipping materials properly. Failure to do so

can result in death, explosion, ﬁre, or burns.

•Place dryer at least 18 inches above the ﬂoor

for a garage installation. Failure to do so can

result in death, explosion, ﬁre, or burns.

•Keep all packaging from children. Packaging

material can be dangerous for children. There is

a risk of suffocation.

•Do not install near another source of heat

such as a stove, cooking oven. Failure to do

so can cause deform, smoke and ﬁre.

•Do not place candles, smoking materials,

or other ﬂammables on top of the product.

Dripping wax, smoke, or ﬁre can result.

•Remove all protective vinyl ﬁlm from the

product. Failure to do so can cause product

damage, smoke or ﬁre.

6

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, injury to persons, or death.

Exhaust/Ducting:

•GasdryersMUSTbeexhaustedtothe

outside. Failure to follow these instructions

can result in ﬁre or death.

•The dryer exhaust system must be exhausted

to the outside of the dwelling. If the dryer is

not exhausted outdoors, some ﬁne lint and

large amounts of moisture will be expelled

into the laundry area. An accumulation of

lint in any area of the home can create a health

and ﬁre hazard.

•Use only rigid metal or ﬂexible metal 4-inch

diameter ductwork inside the dryer cabinet

or for exhausting to the outside. Use of

plastic or other combustible ductwork can

cause a ﬁre. Punctured ductwork can cause

a ﬁre if it collapses or becomes otherwise

restricted in use or during installation.

•Ductwork is not provided with the dryer, and

you should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the dryer

is not in use. Failure to follow these instructions

can result in ﬁre or death.

•The exhaust duct must be 4 inches

(10.2 cm) in diameter with no obstructions.

The exhaust duct should be kept as short as

possible. Make sure to clean any old ducts

before installing your new dryer. Failure to

follow these instructions can result in ﬁre or

death.

•Rigid or semi-rigid metal ducting is

recommended for use between the

dryer and the wall. In special installations

when it is impossible to make a connection

with the above recommendations, a UL-

listed ﬂexible metal transition duct may be

used between the dryer and wall connection

only. The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁre or death.

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁciency

of the exhaust system. Secure all joints with

duct tape. For complete details, follow the

Installation Instructions. Failure to follow these

instructions can result in ﬁre or death.

SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS

•Do not open the dryer door during steam

cycles. Failure to follow these instructions can

result in a burn hazard.

•Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂammable or explosive substances as they

give off vapors that could ignite or explode.

Failure to follow these instructions can result in

ﬁre or death.

•Do not ﬁll the steam feeder with gasoline,

dry-cleaning solvents, or other ﬂammable or

explosive substances. Failure to follow these

instructions can result in ﬁre or death.

•Do not touch the steam nozzle in the drum

during or after the steam cycle. Failure to

follow these instructions can result in a burn

hazard.

•Do not ﬁll the steam feeder with hot water

(over 86 ˚F/30 ˚C). Failure to follow these

instructions can result in a burn hazard.

wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this

appliance, follow basic precautions, including the following:

wWARNING: To reduce the risk of injury to persons , follow all industry recommended safety

procedures including the use of long sleeved gloves and safety glasses. Failure to follow all of the safety

warnings in this manual could result in property damage, injury to persons or death.

ENGLISH

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

•Do not, under any circumstances, cut or

remove the ground prong from the power

cord. To prevent injury to persons or damage

to the dryer, the electrical power cord must be

plugged into a properly grounded outlet.

•For personal safety, this dryer must be

properly grounded. Failure to do so can result

in electric shock or injury.

•Refer to the installation instructions in this

manual for speciﬁc electrical requirements

for your model. Failure to follow these

instructions can create an electric shock hazard

and/or a ﬁre hazard.

•This dryer must be plugged into a properly

grounded outlet. Electric shock can result if

the dryer is not properly grounded. Have the

wall outlet and circuit checked by a qualiﬁed

electrician to make sure the outlet is properly

grounded. Failure to follow these instructions

can create an electric shock hazard and/or a ﬁre

hazard.

•The dryer should always be plugged into

its own individual electrical outlet which

has a voltage rating that matches the rating

plate. This provides the best performance

and also prevents overloading house wiring

circuits which could cause a ﬁre hazard from

overheated wires.

•Never unplug your dryer by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet. The power cord

can be damaged, resulting in a risk of ﬁre and

electric shock.

•Repair or replace immediately all power

cords that have become frayed or otherwise

damaged. Do not use a cord that shows

cracks or abrasion damage along its length

or at either end. The power cord can melt,

creating an electric shock and/or ﬁre hazard.

•When installing or moving the dryer, be

careful not to pinch, crush, or damage

the power cord. This will prevent injury and

prevent damage to the dryer from ﬁre and

electric shock.

SAVE THESE INSTRUCTIONS

7

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

READ ALL INSTRUCTIONS BEFORE USE

wWARNING

For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, injury to persons , or death.

SPECIAL FEATURES

A

EASY-TO-USE CONTROL PANEL

Rotate the cycle selector knob to select the

desired dry cycle. Add cycle options or adjust

settings with the touch of a button.

B

EASY-ACCESS REVERSIBLE DOOR

The wide-opening door provides easy access for

loading and unloading. The door hinge can be

reversed to adjust for installation location.

C

STEAM FUNCTIONS

LG’s steam technology allows you to inject

fabrics with a swirling jet of hot steam to refresh

clothes, reduce static, and make ironing easier.

Simply select the STEAMFRESH

™

cycle, or you

can add a Steam option to selected cycles.

D

FLOW SENSE™ DUCT BLOCKAGE SENSING

SYSTEM INDICATOR

The FLOW SENSE™ duct blockage sensing

system detects and alerts you to blockages in

the ductwork that reduce exhaust flow from the

dryer. Clean exhaust systems increase efficiency

and reduce drying times.

E

SMARTDIAGNOSIS™

Should you experience any technical difficulty

with your dryer, it has the capability of

transmitting data via your telephone to the

Customer Information Center. The call center

agent records the data transmitted from your

machine and uses it to analyze the issue,

providing a fast and effective diagnosis (refer to

page 41).

C

E

R

T

I

F

I

E

D

E

S

I

G

N

C

AE

B

D

8

ENGLISH

B

LEVELING FEET

Four leveling feet (two in the front, and two in the back)

adjust to improve dryer stability on uneven floors.

A

FRONT-MOUNT LINT FILTER

Front-mount lint filter allows for easy access and

cleaning after every load.

KEY PARTS AND COMPONENTS

In addition to the special features and

components outlined in the Special Features

section, there are several other important

components that are referenced in this manual.

DRYING RACK

Use the drying rack with the RACK DRY cycle to safely dry

such items as sweaters, delicates and gym shoes without

tumbling or overheating.

C

Included Accessories

Drying Rack

C

B

A

Rear of Dryer

Terminal Block

Access Panel

(Electric Models)

Power Cord Location

(Gas Models)

Gas

Connection

Location

(Gas Models)

Exhaust Duct

Outlet

9

24 in.

2*

(155 cm

2

)

18" min.*

(45.7 cm)

1"*

(2.5 cm)

30"

(76.1cm)

30"

(76.1cm)

5"**

(12.7 cm)

48 in.

2*

(310 cm

2

)

14" max.*

(35.6 cm)

3"

*

(7.6 cm)

3"

*

(7.6 cm)

1"

(2.5 cm)

27"

(68.6 cm)

1"

(2.5 cm)

1"*

(2.5 cm)

5"**

(12.7 cm)

14" max.*

(35.6 cm)

18" min.*

(45.7 cm)

0"

(0 cm)

39"

(98.3 cm)

1"

(2.5 cm)

27"

(68.6 cm)

1"

(2.5 cm)

CLEARANCES

WARNING: Read all installation instructions completely before installing

and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. Detailed instructions concerning

electrical connections, gas connections, and exhaust requirements are provided on the following pages.

Do not operate your dryer at temperatures below 45 ºF (7 ºC). At lower temperatures, the dryer might not shut off at the

end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile

homes or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

INSTALLATION LOCATION REQUIREMENTS

A location that allows for proper exhaust installation.

A gas dryer must be exhausted to the outdoors. See

Venting Requirements.

A grounded electrical outlet located within 2 ft.

(61 cm) of either side of the dryer. See Electrical

Requirements.

A sturdy ﬂoor to support the total dryer weight of

200 lbs (90.7 kg). The combined weight of a companion

appliance should also be considered.

A level ﬂoor with a maximum slope of 1 inch (2.5 cm)

under entire dryer. If slope is greater than 1 inch (2.5

cm), install the Extended Dryer Feet Kit. Clothes may

not tumble properly, and automatic sensor cycles may

not operate correctly if dryer is not level.

For a garage installation, you will need to place the dryer

at least 18 inches (46 cm) above the ﬂoor. If using a

pedestal, you will need 18 inches (46 cm) to the bottom

of the dryer.

w

The following spacing dimensions are recommended

for this dryer. This dryer has been tested for spacing

of 0 inches (0 cm) clearance on the sides and rear.

Recommended spacing should be considered for the

following reasons:

Additional spacing should be considered for ease of

installation and servicing.

Additional clearances might be required for wall, door

and ﬂoor moldings.

Additional spacing should be considered on all sides of

the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

Companion appliance spacing should also be

considered.

Suggestion: There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer

of vibration from one to the other. Too much vibration, it could cause them to make noise or touch each other causing

paint damage and making even more noise.

Installation spacing for recessed area or closet installation

10

ENGLISH

30"

(76.1cm)

5"**

(12.7 cm)

1"**

(2.5 cm)

1"

(2.5 cm)

1"

(2.5 cm)

27"

(68.6 cm)

9"**

(22.9 cm)

7"* (17.8 cm)

1"* (2.5 cm)

5

"**

(14 cm)

1/2

77

1/2

"

(196.8 cm)

For cabinet installation with a door, minimum ventilation openings in the top of the cabinet

are required.

Recommended installation spacing for cabinet installation

INSTALLATION WITH OPTIONAL PEDESTAL BASE OR STACKING KIT

WARNING : If you are installing your dryer using an optional pedestal base or stacking kit, please

refer to Optional Accessories in this manual or to the instructions for your pedestal or stacking kit

before proceeding with the installation.

*Required spacing

** For side or bottom venting, 2 inches

(5.1 cm) spacing is allowed.

The dimensions shown are for the recommended spacing.

Recommended installation spacing for recessed or closet

installation, with stacked washer and dryer

Closet ventilation requirements

Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in

the closet. One upper vent opening with a minimum opening of 48 sq. in. (310 cm

2

) must be installed

no lower than 6 feet above the floor. One lower vent opening with a minimum opening of 24 sq. in.

(155 cm

2

) must be installed no more than one foot above the floor. One example shown uses vent

grilles in the door.

*Required spacing

** For side or bottom

venting, 2 inches

(5.1 cm) spacing is

allowed.

11

Position the dryer in the final location. Place

a level across the top of the dryer.

1

Level

Leveling Feet

Use an adjustable wrench to turn the leveling

feet. Turn clockwise to raise the dryer or

counterclockwise to lower it. Raise or lower

the leveling feet until dryer is level from

side to side and front to back.

Make sure that all 4 leveling feet are in firm

contact with the floor.

2

•Allfourleveling feetmustrestsolidly on the

floor. Gently push on the top corners of the

dryer to make sure that the dryer does not

rock from corner to corner.

If you are installing the dryer on the optional

pedestal, you must use the leveling feet on the

pedestal to level the dryer. The dryer leveling feet

should be fully retracted.

OPTIONAL ACCESSORIES

For these and other LG products, contact your local LG dealer, or visit our Web site at www.lg.com.

Stacking Kit

(sold separately)

Pedestal

(sold separately)

LEVELING THE DRYER

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize

vibration, noise, and unwanted movement, the

floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as

necessary to level the dryer. Extending the

leveling feet more than necessary can cause

the dryer to vibrate.

WARNING

•Toreducetheriskofinjurytopersons,adhere

to all industry recommended safety procedures

including the use of long sleeved gloves and

safety glasses.

•Theappliancesareheavy.Twoormorepeople

are required when installing the dryer.

•Failuretofollowallofthesafetywarningsinthis

manual could result in property damage, injury

to persons or death.

w

12

ENGLISH

TO REMOVE THE DOOR

wWARNING

THEDRYERDOORISVERYLARGEANDHEAVY.Failure to follow the instructions below can result in damage

to the dryer, property damage or injury to persons .

• Toavoiddamagetothedryerorthedoor,supportthedoorwithastoolorboxthatfitsunderthedoor,orhave

an assistant support the weight of the door.

• AlwaysreversethedoorBEFOREstackingthedryerontopofthewasher.

• Avoiddroppingthedoortoavoiddamagetothedoororthefloor.

Remove four dummy screws by driver.

3

Hinge

Dummy

Screw

Remove door from cabinet cover.

6

Remove

Door

Check screws to remove (Left 6, Right 4).

2

Hold on the hinge while remove 4 screws of

hinge (to prevent door dropping).

5

Hinge Screw

Open the door to reverse.

1

Open Door

Remove two screws and disassembly Latch.

4

Latch Screw

13

TO INSTALL THE DOOR

wWARNING

THEDRYERDOORISVERYLARGEANDHEAVY.Failure to follow the instructions below can result in damage

to the dryer, property damage or injury to persons .

• Toavoiddamagetothedryerorthedoor,supportthedoorwithastoolorboxthatfitsunderthedoor,orhave

an assistant support the weight of the door.

• AlwaysreversethedoorBEFOREstackingthedryerontopofthewasher.

• Avoiddroppingthedoortoavoiddamagetothedoororthefloor.

Insert latch to right side and install screws.

3

Latch

Screw

Move door to left side and insert a hinge to

hinge hole.

1

Hinge hole

Screw down four dummy screws right side.

4

Hinge

Dummy

Screw

Check that the door closes and latches

properly.

5

Swing Door

Hold on hinge while screw down a hinge

(to prevent door dropping).

2

Hinge Screw

14

ENGLISH

15

CHANGING THE DRYER VENT LOCATION

Your new dryer is shipped to vent to the rear.

It can also be configured to vent to the bottom or side

(right-side venting is not available on gas models).

An adapter kit, part number 383EEL9001B, may be

purchased from your LG retailer. This kit contains the

necessary duct components to change the dryer vent

location.

Remove the rear exhaust duct retaining

screw. Pull out the exhaust duct.

1

Rear

Exhaust Duct

Retaining

Screw

Preassemble a 4 inches (10.2 cm) elbow to the

next 4-inches (10.2 cm) duct section, and secure

all joints with duct tape. Be sure that the male

end of the elbow faces AWAY from the dryer.

Insert the elbow/duct assembly through the side

opening and press it onto the adapter duct.

Secure in place with duct tape.

Be sure that the male end of the duct protrudes

1½ inches (3.8 cm) to connect the remaining

ductwork.

Attach cover plate to the back of the dryer with

included screw.

1

/2"

(3.8 cm)

3

Elbow

Cover

Plate

Insert the

4 inches

(10.2 cm) elbow through

the rear opening and press it onto the

adapter duct. Be sure that the male end of

the elbow faces down through hole in the

bottom of the dryer. Secure in place with

duct tape.

Attach the cover plate to the back of the

dryer with included screw.

3

Elbow

Cover

Plate

Press the tabs on the knockout and carefully

remove the knockout for the desired vent

opening (right-side venting is not available on

gas models). Press the adapter duct onto the

blower housing and secure to the base of the

dryer as shown.

2

Knockout

Bracket

Adapter

Duct

OPTION 1: Side Venting

Press the adapter duct onto the blower

housing and secure to the base of the dryer

as shown.

2

Bracket

Adapter

Duct

OPTION 2: Bottom Venting

WARNING

w

•Useaheavymetalvent.

•Donotuseplasticorthinfoilduct.

•Cleanoldductsbeforeinstallingthisdryer.

•Toreducetheriskofinjurytopersons,adheretoall

industry recommended safety procedures including

the use of long sleeved gloves and safety glasses.

•Failuretofollowallofthesafetywarningsinthis

manual could result in property damage, injury to

persons or death.

VENTING THE DRYER

•Do not crush or collapse ductwork. Failure

to follow these instructions can result in ﬁre

or death.

•Do not allow ductwork to rest on or

contact sharp objects. Failure to follow these

instructions can result in ﬁre or death.

•If connecting to existing ductwork, make

sure it is suitable and clean before installing

the dryer. Failure to follow these instructions

can result in ﬁre or death.

•Venting must conform to local building

codes. Failure to follow these instructions can

result in ﬁre or death.

•GasdryersMUSTexhausttotheoutdoors.

Failure to follow these instructions can result

in ﬁre or death.

•Use only 4-inch (10.2 cm) rigid or ﬂexible

metal ductwork inside the dryer cabinet and

for venting outside. Failure to follow these

instructions can result in ﬁre or death.

•To reduce the risk of ﬁre, combustion, or

accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall,

ceiling, crawl space, chimney, gas vent, or

concealed space of a building. Failure to

follow these instructions can result in ﬁre

or death.

•To reduce the risk of ﬁre, DO NOT exhaust

the dryer with plastic or thin foil ducting.

Failure to follow these instructions can result

in ﬁre or death.

•The exhaust duct must be 4 inches

(10.2 cm) in diameter with no obstructions.

The exhaust duct should be kept as short as

possible. Make sure to clean any old ducts

before installing your new dryer. Failure to

follow these instructions can result in ﬁre or

death.

•Rigid or semirigid metal ducting is

recommended for use between the dryer

and the wall. In special installations when

it is impossible to make a connection with

the above recommendations, a UL-listed

ﬂexible metal transition duct may be used

between the dryer and wall connection only.

The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁre or death.

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁciency

oftheexhaustsystem.Securealljoints

with duct tape. Failure to follow these

instructions can result in ﬁre or death.

•To maximize operating results, please

observe the duct length limitations noted in

the chart on page 17. Failure to follow these

instructions can result in ﬁre or death.

•Ductwork is not provided with the dryer.

You should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the

dryer is not in use. Failure to follow these

instructions can result in ﬁre or death.

•The Total length of ﬂexible metal duct shall

not exceed 8 ft. (2.4m)

•In Canada, that only those foil-type ﬂexible

ducts, if any, speciﬁcally identiﬁed for use

with the appliance by the manufacturer

shall be used. In the United States, that only

those foil-type ﬂexible ducts, if any, speciﬁcally

identiﬁed for use with the appliance by the

manufacturer and that comply with the Outline

for Clothes Dryer Transition Duct, Subject

2158A, shall be used.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

16

ENGLISH

Routing and Connecting Ductwork

Follow the guidelines below to maximize drying

performance and reduce lint buildup and

condensation in the ductwork.

NOTE: Ductwork and fittings are NOT included

and must be purchased separately.

•Use4-inch(10.2cm)diameterrigidorsemirigid

metal ductwork.

•Theexhaustductrunshouldbeasshortas

possible.

•Useasfewelbowjointsaspossible.

•Themaleendofeachsectionofexhaustduct

must point away from the dryer.

•Useducttapeonallductjoints.

•Insulateductworkthatrunsthroughunheated

areas in order to reduce condensation and lint

buildup on duct surfaces.

IMPORTANT: Failure to exhaust the dryer

correctly will void the dryer’s warranty.

VENTING THE DRYER (cont.)

Correct Venting

Incorrect Venting

NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.

65 ft. (19.8 m)

55 ft. (16.8 m)

47 ft. (13.7 m)

36 ft. (11.0 m)

28 ft. (8.5 m)

55 ft. (16.8 m)

47 ft. (13.7 m)

41 ft. (12.5 m)

30 ft. (9.1 m)

22 ft. (6.7 m)

Ductwork

4"

(10.2 cm)

4"

(10.2 cm)

Recommended

2

1

/2"

(6.35 cm)

Use Only for Short

Run Installations

Wall Cap Type

0

1

2

3

4

0

1

2

3

4

Number of 90° Elbows

Maximum Length of 4-inch Diameter

Rigid Metal Duct

17

18

Electrical Requirements for Gas Models Only

• Do not, under any circumstances, cut or

remove the third (ground) prong from the power

cord. Failure to follow this warning can result in

ﬁre, explosion, or death.

• For personal safety, this dryer must be properly

grounded. Failure to follow this warning can result

in ﬁre, explosion, or death.

• The power cord of this dryer is equipped with

a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock

hazard from this appliance. Failure to follow this

warning can result in ﬁre, explosion, or death.

• This dryer must be plugged into a

60 Hz, 120 VAC. grounded outlet protected by

a 15-ampere fuse or circuit breaker. Failure to

follow this warning can result in ﬁre, explosion,

or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility

and obligation to have it replaced with a

properly grounded 3-prong wall outlet. Failure

to follow this warning can result in ﬁre, explosion,

or death.

CONNECTING GAS DRYERS

•Gas supply requirements:

As shipped from the factory, this dryer is

conﬁgured for use with natural gas. It can be

converted for use with LP (Liqueﬁed Propane)

gas. Gas pressure must not exceed 13 inches

of water column.

•A qualiﬁed service or gas company technician

must connect the dryer to the gas service.

Failure to do so can result in ﬁre, explosion,

or death.

•Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve

during any pressure testing of the gas supply.

Failure to do so can result in ﬁre, explosion,

or death.

•Supplylinerequirements:

Your laundry room must have a rigid gas

supplylinetoyourdryer.IntheUnitedStates,

anindividualmanualshutoffvalveMUSTbe

installed within at least 6 ft. (1.8 m) of the dryer,

in accordance with the National Fuel Gas Code

ANSIZ223.1orCanadiangasinstallationcode

CSAB149.1.A

1

⁄8 - inch NPT pipe plug must

be installed. Failure to do so can result in ﬁre,

explosion, or death

•If using a rigid pipe, the rigid pipe should be

½-inchIPS.Ifacceptableunderlocalcodes

and ordinances and when acceptable to your

gas supplier,

3

⁄8 - inch approved tubing may be

used where lengths are less than 20 ft.

(6.1 m). Larger tubing should be used for

lengths in excess of 20 ft. (6.1 m). Failure to do

so can result in ﬁre, explosion, or death.

•Connect the dryer to the type of gas shown on

the nameplate. Failure to do so can result in ﬁre,

explosion, or death.

•To prevent contamination of the gas valve,

purge the gas supply of air and sediment

before connecting the gas supply to the dryer.

Before tightening the connection between the

gas supply and the dryer, purge remaining air

until the odor of gas is detected. Failure to do

so can result in ﬁre, explosion, or death.

•DO NOT use an open ﬂame to inspect for gas

leaks. Use a noncorrosive leak-detection ﬂuid.

Failure to do so can result in ﬁre, explosion, or

death.

•UseonlyanewAGA-orCSA-certiedgas

supply line with ﬂexible stainless steel

connectors. Failure to do so can result in ﬁre,

explosion, or death.

•Securelytightenallgasconnections. Failure

to do so can result in ﬁre, explosion, or death.

•Use a pipe-joint compound that is insoluble

in Liqueﬁed Petroleum (LP) gas on all pipe

threads. Failure to do so can result in ﬁre,

explosion, or death.

•DO NOT attempt any disassembly of the dryer;

any disassembly requires the attention and

tools of an authorized and qualiﬁed service

person or company. Failure to do so can result

in ﬁre, explosion, or death.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

ENGLISH

•Installation and service must be performed

by a qualiﬁed installer, service agency, or the

gas supplier. Failure to do so can result in ﬁre,

explosion, or death.

•Use only a new stainless steel ﬂexible

connector and a new AGA-certiﬁed

connector. Failure to do so can result in ﬁre,

explosion, or death.

•A gas shutoff valve must be installed within

6 ft. (1.8 m) of the dryer. Failure to do so can

result in ﬁre, explosion, or death.

•The dryer is conﬁgured for Natural Gas when

shipped from the factory. Make sure that the

dryer is equipped with the correct burner

oriﬁce for the type of gas being used (Natural

Gas or Liqueﬁed Petroleum). Failure to do so

can result in ﬁre, explosion, or death.

•If necessary, the correct oriﬁce (for the LP

oriﬁce kit order part number 383EEL3002D)

should be installed by a qualiﬁed technician

and the change should be noted on the dryer.

Failure to do so can result in ﬁre, explosion,

or death.

•All connections must be in accordance with

local codes and regulations. Failure to do so

can result in ﬁre, explosion, or death.

•GasdryersMUSTexhausttotheoutdoors.

Failure to do so can result in ﬁre, explosion,

or death.

3/8” NPT Gas

Connection

Gas Supply

Shutoff Valve

Connecting the Gas Supply

Make sure that the gas supply to the laundry

room is turned OFF. Confirm that the type

of gas available in your laundry room is

appropriate for the dryer. The dryer is

prepared for Natural Gas with a

3

⁄8 - inch NPT

gas connection.

Remove the shipping cap from the gas

connection at the back of the dryer. Be

careful not to damage the threads of the gas

connector when removing the shipping cap.

Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel

connector with a

3

⁄8 - inch NPT fitting.

Securely tighten all connections between the

dryer and your laundry room’s gas supply.

Turn on your laundry room’s gas supply and

check all pipe connections (both internal and

external) for gas leaks with a noncorrosive

leak-detection fluid.

1

2

3

4

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for

elevations below 10,000 feet.

If your gas dryer is being installed at an elevation

above 10,000 feet, it must be derated by a

qualified technician or gas supplier.

Electrical Connection

Plug dryer into a

120 VAC, 60 Hz

grounded 3-prong

outlet.

CONNECTING GAS DRYERS (cont.)

1/8” NPT Pipe

Plug

AGA/CSA-Certified

Stainless Steel

Flexible Connector

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

19

20

Electrical Requirements for Electric Models Only

•This dryer must be connected to a grounded

metal, permanent wiring system, or an

equipment-grounding conductor must

be run with the circuit conductors and

connected to the equipment-grounding

terminal or lead on the dryer. Failure to do

so can result in ﬁre, explosion, or death.

•The dryer has its own terminal block that

must be connected to a separate 240 VAC,

60-Hertz, single-phase circuit, fused at 30

amperes (the circuit must be fused on both

sidesoftheline).ELECTRICALSERVICE

FORTHEDRYERSHOULDBEOFTHE

MAXIMUMRATEVOLTAGELISTEDONTHE

NAMEPLATE. DO NOT CONNECT DRYER

TO 110-, 115-, OR 120-VOLT CIRCUIT. Failure

to follow these instructions can result in ﬁre,

explosion, or death.

•If branch circuit to dryer is 15 ft. (4.5 m)

or less in length, use UL (Underwriters

Laboratories) listed No.-10 AWG wire

(copper wire only), or as required by local

codes. If over 15 ft. (4.50 m), use UL-listed

No.-8 AWG wire (copper wire only), or as

required by local codes. Allow sufﬁcient

slack in wiring so dryer can be moved from

its normal location when necessary. Failure

to do so can result in ﬁre, explosion, or death.

•The power cord (pigtail) connection between

wallreceptacleanddryerterminalblockIS

NOT supplied with dryer. The pigtail must be

the correct plug and wire gauge and must

conform to local codes and with instructions

on the following pages. Failure to follow these

instructions can result in ﬁre, explosion, or

death.

•A 4-wire connection is required for all mobile

and manufactured home installations, as

well as all new construction after January

1, 1996. A 4-wire connection must be used

where local codes do not permit grounding

through the neutral wire. Failure to do so can

result in ﬁre, explosion, or death.

Special Electrical Requirements for Mobile or Manufactured Homes

•Any installation in a manufactured or mobile

home must comply with the Manufactured

Home Construction and Safety Standards

Title 24 CFR, Part 32-80 or Standard CAN/

CSA0Z240 MH and local codes and ordinances.

•A 4-wire connection is required for all mobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

Failure to do so can result in ﬁre, explosion,

or death.

CONNECTING ELECTRIC DRYERS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and

grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all

applicable local regulations. Please contact a qualified electrician to check your home’s wiring and

fuses to ensure that your home has adequate electrical power to operate the dryer.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING:

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Donotmodifytheplugandinternalwire

provided with the dryer.

•Thedryershouldbeconnectedto4-holeoutlet.

•Ifitdoesnotttheoutlet,aproperoutletwill

need to be installed by a qualiﬁed electrician.

La page charge ...

LG DLEX2550N Le manuel du propriétaire

LG DLEX2550N Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents