KitchenAid KUDC02IRBL0 Guide d'installation
- Catégorie
- Lave-vaisselle
- Taper
- Guide d'installation
t
KitchenA_d °
HOME APPLIANCES
_r
Table of Contents ............................................................................. 2
Table des mati_res ......................................................................... 19
8572290
8572290
TabUe of Contents
Dishwasher Safety ................................. 2
installation Requirements ........................... 3
Tools and parts ................................. 3
Location Requirements .......................... 3
Drain Requirements ............................. 5
Water Supply Requirements ...................... 5
Electrical Requirements .......................... 5
Installation instructions ............................. 6
Prepare cabinet opening
using existing utility hookups ..................... 6
Prepare cabinet opening
where there are no existing utility hookups .......... 7
Prepare dishwasher ............................. 9
Make electrical connection ...................... 13
Connect to water supply ........................ 14
Connect to drain ............................... 15
Secure dishwasher in cabinet opening ............. 15
Dishwasher Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until compmetemy installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You need to:
o Slowly open dishwasher door while someone grasps the
rear of the dishwasher, Remove shipping materials, drain
hose and lower rack Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions,
Installation should be performed by a qualified service
technician,The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
Installation Requirements
TooJs and Parts
Gather the required toois and parts before starting
installation. Read and follow the instructions provided with
any toois Hsted here.
AH installations
Tools needed:
+ pliers
+ PhHHps screwdriver
+ 5/16" and 1/4" nut drivers
or hex sockets
+ measuring tape or ruler
+ 10" adjustable wrench that
opens to 1-1/8" {2.9 cm)
+ fiat+Made screwdriver
®utility knife
+ 2 twist+on wire connectors
which are the proper size
to connect your household
wiring to 16+gauge wiring
in dishwasher
+ small level
+TORX+T15 screwdriver (if
installing custom front
panels)
®flashlight
+ shallow pan
+ electric drill with 3/32" bit
+ 5/8" open-end wrench
+ bath towel
+ wood block
Parts needed:
+90° elbow with 3/8" N,RT,
external threads on one
end, (The other end must
fit your water supply line,)
+Teflon x tape or pipe joint
compound
+shims (if installed with
built+up floor)
+4 #10 x 1/2" wood screws
(if installing custom front
panels)
In addition, for new installations
Tools needed: Parts needed:
+ electric drill with 1/2", 3/4"
and 1-1/2" hole saw bits
+ small tubing cutter
®wire stripper
®1-1/2"+2" screw-type clamp
if connecting to waste+tee
+ copper tubing (3/8"
recommended) or flexible
stainless steel braided fill
line
+ clamp connector or
conduit connector to fit a
7/8" (2.2 cm) diameter hole
Parts supplied
A. 2 - drain hose clamps, 1 large and 1 small
B. 2 - # 10 x 1/2" Phillips-head screws
C. drain hose
B
C
Additional parts supplied with top-venting models only
D. 2 #8 x l+3/8"TORX+T15 screws
E, 4 #10 x 3/8" hex+head screws
Additional part supplied with certain models
E Bottom sound pad (located in upper rack)
Make sure ail these parts are included. If not included, cail
1-800+422-1230.
See separate parts list for accessories available for your
dishwasher.
@Teflon is a registered trademark of E.I. Du Pont de Nemours and
Company.
{R_Registered trademark of TEXTRON.
Location Requirements
Do not run drain lines, water lines or electrical wiring
where they can interfere with or contact dishwasher motor
or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warrant%
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.This may also be obtained by calling
1-800-422+1230.
Check location where dishwasher will be installed.The
location must provide:
+ easy access to water, electricity and drain.
+ convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wail or
cabinet.
+ square opening for proper operation and appearance.
+ cabinet front perpendicular to floor.
+ level floor. (if floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwashery
NOTE:To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Cutout dimensions" section.
HelpfulTip: if the floor in the dishwasher opening is
uneven (example: tile flooring only partway into
opening) you will need to take special care in
measuring dimensions and in leveling dishwasher.
Product dimensions
3/4" (!.9 cm)-a_
insu !ation -
may be
compressed
(not used on
al! models)
24-7/8" (63.2 cm) _1
/
I I front vent
24-1/2" (62.2 cm) _ _11 _
I Ill SS-TJS"
Ill I (s6cm>mh_.
removed
_- 21" (53.3 cm)--_ I
SIDE VIEW
23-7/8" (60.6 cm)
REAR VIEW
Cutout dimensions
All surfaces must be free
/'_- from intrusions
I ÷1
._ (5.1 cm) 10"
(25.4
2-3/4" 3-1/4"
(7 cm) (8.3 cm) (8.3 cm) (7 cm)
Cut holes in shaded area of cabinet walls or floor as specified below:
water line - 1/2" (!.3 cm)
drain line- 1-1/2" (3.8 cm)
direct wire - 3/4" (!.9 cm)
power supply cord - 1-1/2" (3.8 cm)
34 _'
(86.4 cm)
min.
Measured from the lowest point on the underside of countertop. May be
reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.
Minimum, measured from narrowest point of opening.
May be increased to 6-5/8" (16.6 cm) if height of opening is 34-1/2"
(876 cm) at its lowest point.
!
Drain Requirements
o Use the new drain hose suppHbd with your dishwasher.
IftMs is not [ong enough, use a new drain hose with a
maximum [ength of 12 feet (3.7 m) that meets all[
current AHAM/[APMO test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain
connector of the dishwasher.
o Connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor, it is recommended that the
drain hose either be looped up and securely fastened
to the underside of the counter, or be connected to an
air gap.
air gap
o Use an air gap if the drain hose is connected to house
plumbing lower than 20" (50.8 cm} above subfloor or
floor.
o Use 1/2" minimum I.D. drain line fittings.
Water SuppJy Requirements
_A hot water line with 20-120 psi (138-862 kPa) water
pressure.
o 120°F (49°C) water at dishwasher.
o 3/8" O.D. copper tubing with compression fitting or
flexible stainless steel braided fill line (1/2" minimum
plastic tubing is not recommended).
o A 90 ° elbow with 3/8" N.RT. external pipe threads on
one end.
Do not solder within 6" (15.2 cm) from water inlet valve.
EJectricaJ Requirements
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with aii national and local codes and
ordinances.
You must have:
o 120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical
suppl%
®Copper wire only.
We recommend:
o A timeodelay fuse or circuit breaker.
o A separate circuit,
ff direct wiring dishwasher:
Use flexible, armored or nonometallic sheathed, copper
wire with grounding wire that meets the wiring
requirements for your home and local codes and
ordinances.
Use strain relief method provided with house wiring
junction box or install a U.L.-listed/CSAocertified clamp
connector to the house wiring junction box. if using
conduit, use a U.L.-listed/CSA-certified conduit connector.
_fconnecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part No. 4317824} marked for
use with dishwashers. Kit contents include:
-Volex, inc., UL listed 16 gauge 3 wire power supply
cord with 3 prong grounded plug.
- Neer C-500 7/8 inch strain relief.
- 3 wire connectors.
- Part No. 302797 grommet
Follow the kit instructions for installing the power
supply cord.
o Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes and
ordinances.
Installation Instructions
EBectrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Turn off water suppiy.
Prepare cabinet opening using
existing utility hookups
Follow the steps in this section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
®Jf you are installing the dishwasher in a cabinet opening
that does not have hookups, follow the steps under
"Prepare cabinet opening where there are no existing
utility hookups" section.
1. Check that the water
line reaches to the
front left of opening
where the water
connection will be
made.
2. Check that the direct _
wire reaches to the
front right of opening 6" (15.2 cm)
where the electrical
connection will be made.
If the water line and the direct wire reach far enough into
the opening, proceed to the next section "install the drain
hose/' Jf they do not reach far enough, follow the steps
under "Prepare cabinet opening where there are no
existing utility hookups:'
JnstalJ the drain hose
IMPORTANT: Always use a new drain hose even when
installing a new replacement dishwasher,
1. Drill a 1-1/2" (3,8 cm) diameter hob in cabinet wall or
floor on the side of the opening closest to the sink
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
o Option 1, Waste disposer- with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer- no air gap _
Option 4, No waste disposer - no air gap _
_anair gap is recommended
HeJpfuITip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1: Waste disposer -with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp, if the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clampX.
3. Use a rubber hose connector _ with spring or screw-
type clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at
bast 20" (50.8 cm) above the floor where dishwasher
will be installed,
drain hose -
cut here if needed
rubber hose
ector
gap
large
J spring-type
clamp
_ drain
hose
drain trap
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made,
drain hose
Parts available from local plumbing supply stores
Option 2: No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type
damp. if the drain hose was cut, use a 1-1/2" to 2"
(&8 to 5 cm) screw-type damp ×,
3. Use a rubber hose connector _ with spring or screw-
type damps .×.to connect air gap to waste tee_
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed_
drain hose-
cut here if needed
rubber hose
connector
large
spring4ype
waste
tee drain
drain trap hose
4. insert drain hose |
through hob cut in
cabinet to the front
center of opening where
drain connection will be /
made.
drain hose
Parts available from local plumbing supply stores
Option 3: Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
2. Attach drain hose to disposer inlet with large spring_
type damp.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed, it is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
large spring-type
clamp
drain hose
disposer
inlet
drain trap
3. insert drain hose |
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Option 4: No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section),
2. Attach drain hose to waste tee with lq/2" to 2"
(3,8 to 5 cm) screw-type clampX,
This connection must be before the drain trap and at
bast 20" (50,8 cm) above the floor where dishwasher
will be installed, it is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter,
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Parts available from local plumbing supply stores
Prepare cabinet opening where there
are no existing utility hookups
Electrical connection
Option1: Direct wire method:
HeJpfu_Tip: Wiring the dishwasher wiii be easier if you
route wire into the cabinet opening from theri htside,
1. Drill a 3/4" (1,9 cm)
hob in rightohand
cabinet side, rear or
floor. Preferred and
optional locations are
shown,
2. Wood cabinet: Sand
hob until smooth.
Metal cabinet: Cover
3,
4.
5,
_1_oOptional preferred
ns Iocat_i.,
hob with grommet, not provided.
Run wire into house wiring junction box.
Install a U.L.qisted/CSAocertified clamp connector
(strain relief) for flexibleotype wire. If installing conduit,
attach a U.L.-listed/CSA-certified conduit connector to
the junction box.
Run other end of wire
through cabinet hole.
Cable must extend to the
right front of cabinet
opening.
Option2: Powersupplycordmethod:
NOTE:Amating,threeprong,ground-typewallreceptacle
isrequiredinacabinetnexttothedishwasheropening.
1. DrHHa1ol/2"
(3.8cm)hoHein optionalpreferred
thecabinetrear locationslocations
orside.Preferred[_!_i
andopfionaH ......
Hocafionsare
shown.
2. VVoodcabinet:
SandhoHeunfiH
smooth.
MetaH cabinet: Cover hoHe with grommet (Part No.
302797) incHuded with power suppHy cord kit.
mnstall the water line
HeJpfuJTip: Routing the water Hne through the Heft side
of cabinet opening will make water connection easier.
Drill a minimum 1/2" {1.3 cm) hole in the cabinet side,
rear or floor. Preferred and optional locations are
shown.
preferred
locations
optional
locations
2. Measure overall length
of copper tubing
required.
3. Attach copper tubing
to the water line with a
manual shutoff valve.
copper
tubing
4. Slowly feed copper
tubing through hole in
cabinet. Copper tubing will bend and kink easily, so be
gentle.The copper tubing should be far enough into the
cabinet opening to connect it to dishwasher inlet on the
front left of the dishwasher.
5. Turn water shutoff valve to "ON" position. Flush water
into a shallow pan to get rid of particles that may clog
the inlet valve.
6. Turn shutoff valve to "OFF" position.
mnstaH the drain hose
IMPORTANT: Always use a new drain hose.
1. Drill a 1-1/2" (3.8 cm)
diameter hole in
cabinet wall or floor on
the side of the opening
closest to the sink.
2. Connect drain hose to
waste tee or waste disposer using one of the following
methods:
o Option 1, Waste disposer-with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer - no air gap _
Option 4, No waste disposer - no air gap _
_anair gap is recommended
HeJpfulTip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1: Waste disposer = with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector _ with spring or screw-
type clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
wi[[ be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
large
J spring-type
clamp
hose
drain trap
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Parts available from local plumbing supply stores
Option 2: No waste disposer = with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with Harge spring-type
champ. If the drain hose was cut, use a 1-1/2" to 2"
(&8 to 5 cm) screw-type cHamp x,
3. Use a rubber hose connector _ with spring or screw-
type champs .×.to connect air gap to waste tee_
This connection must be before the drain trap and at
Heast20" (50.8 cm) above the floor where dishwasher
wHHbe instaHHe&
. drainhose-
cuthereif needed
springor
rubber hose
connector
large
spring4ype
waste
tee drain
drain trap hose
4. hsert drain hose
through hoHe cut in
cabinet to the front
center of opening where
drain connection wHHbe
made,
L drain hose
Parts available from local plumbing supply stores
Option 3: Waste disposer = no air gap:
1. Remove the disposer knockout pHug. Do not cut end of
drain hose.
2, Attach drain hose to disposer inlet with large spring_
type clamp,
This connection must be before the drain trap and at
least 20" (50,8 cm) above the floor where dishwasher
will be installed, It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter,
large spring-type
clamp
drain hose
disposer
inlet
drain trap
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made,
drain hose
Option 4: No waste disposer = no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section),
2. Attach drain hose to waste tee with lq/2" to 2"
(3,8 to 5 cm) screw-type clampX,
This connection must be before the drain trap and at
least 20" (50,8 cm) above the floor where dishwasher
will be installed, it is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter,
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made_
_/_ drain hose
Parts available from local plumbing supply stores
Prepare dishwasher
Tip Over Hazard
Do not use dishwasher until compietemy installed,
Do not push down on open door,
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Put corner posts from packaging behind dishwasher,
Grasp sides of dishwasher door frame and put
dishwasher on its back, resting on top of the corner
posts,
2. Remove two screws attaching access panei and bvver
panei to dishwasher using a 1/4" hex socket, nut driver
or PMHips screwdriven
3. Remove paneis and set paneis aside on a protective
surface,
lower
panel
clip
4. Check that grounding clip is
attached to the lower panel,
water inlet valve
5. ApplyTeflon x tape or pipe
joint compound to 90 ° elbow
fitting and connect fitting to
water inlet valve.
& Tighten elbow until snug, and
be sure that it faces to the rear,
7. Remove terminal box cover. Pull appliance wires
through hole in terminal box. Do not untie the knot in
the wires,
- if you are direct wiring: install a U.h-listed/CSAo
certified clamp connector to the terminal box. if using
conduit, use a U.hqisted/CSAocertified conduit
connector.
- if you are installing a power supply cord kit, do so
nov,,,,following kit instructions,
dishwasher
wires --...
\
cable clamp connector
HeJpfuJTip: Put cardboard under dishwasher until it is
installed in cabinet opening.The cardboard will help
protect floor covering during installation,
8. Measure height of cabinet opening
from underside of countertop to
floor where dishwasher will be
installed (you need the lowest
point). Check chart for that height
opening. Put wheels in the required
position.
wheel
Number of
Minimum Wheel
turns on
cutout height position front leg
34" (86.4 cm) 1 10
34-1/4" (87 cm) 2 5
34-I/2" (87.6 cm) 3 0
8,
Turn both front leveler legs to the same
height.
If the minimum cutout height is less than
34" (86.4 cm), the rear wheels can be
removed for additional clearance.This will
allow the dishwasher to fit into a 33-7/8"
(86 cm) high cutout, but the dishwasher
wiii be more difficult to move into
position, if the wheels are removed,
protect the floor when moving the dishwashen
frontleg
If you have built-up floors
1. Measure height of opening
from underside of
countertop to built-up
floor, if the height is at
bast 33-3/4" (85.7 cm), the
dishwasher will fit into the
opening without
modification to the
countertop or flooring,
2. Put wheels in position 1
and turn the front leveler
legs up all the vva%
3,
/ countertop
33-3/4"
(85.7 cm)
min.
shim &) t°?
Add shims as needed in the area shown to bring
dishwasher up to proper height.
NOTE: Shims must be securely attached to floor to
prevent their movement when the dishwasher is
operated.
shim shim
2-3/4" 6"
(7.0cm) (15,2cm) (ZOcm)
lO
mrmstall the door handle (on some models)
IMPORTANT: Do not scratch the front panel during this
procedure.
1. Remove the door handle and hardware bag containing
the setscrews and Allen wrench from the cardboard box.
2. Start set screws in handle,
3. Place handle on mounting studs with the set screws
facing down.
4. Push the door handle tightly against the door, Insert the
short end of the Allen wrench into the setscrews,
Tighten the setscrews 1/4 turn past snug, Retain Allen
wrench with Installation Instructions,
kg
stud
handle
setscrew
(in bottom
of handle)
.._.)
wrench
Pro Lh_e" Series
1. Remove the Pro Line TM Series handle and two screws
from handle package.
2. Make sure plastic spacers are still attached to the door.
3. Attach the handle to the factory-supplied full front panel
as shown.
mnstaH door panel (ProLine series)
NOTE: Features on your
dishwasher may differ
from model shown.
For top vented models
with a factory-supplied topvent
stainless or painted full
front panel:
1. Remove the carton containing the factory-supplied full
front panel.
2. Remove the handle package from the front of the
shipping base.
3. Remove the inner panel from the door.
4. With aTORX _screwdriver, remove three screws from
both sides of the door. Hold the inner panel up while
removing the screws.
5. Gently set panel aside,
NOTE: Some models have 4 screws per side,
screws
screws door
panel do not remove screw,
6. Lay the factory-supplied full front panel face down on a
protective non-scratching surface,
7. Place the inner panel on the back of the full front panel
as shown and attach, using the four #10-16 x 3/8" screws
in the literature package,
4 screws
J
full front panel
inner door panel _ top of panel
8. Attach the factory-supplied full front panel, inner panel,
and handle assembly to the door.
9. Reinstall the two uppermost screws into the inner panel,
do not tighten completely, This will hold the full front
panel in place on the door frame,
2 screws ,
10. Install the two #8-18 x 1-3/8" screws from the literature
package in the top corners of the door,
11. Align the top edge of the full front panel with the top
edge of the console and secure corner screws,
12. Tighten the two screws installed in Step 9.
13. Reinstall and tighten the remaining screws in the inner
panel,
i 2screws i
align top edges
11
Choose attachment option
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using two or more peopie, stand the dishwasher up,
Option 1: Countertop attachment
The dishwasher must be
secured to the cabinet.There
are two brackets on top of the
dishwasher that can be
attached to the countertop if it
is wood, laminate or other
similar surfaces. If this is not
possible, the brackets may be _
moved to the sides of the
dishwasher.
NOTE: Do not attach the
dishwasher, this will be done
later.
brackets
front vent
model shown
Option 2: Dishwasher side attachment
(for marble, granite or other hard surface
countertop)
1. To remove the brackets from the top, flatten tab at back
of brackets with pliers, and pull the brackets out of the
slots,
2. Break off the end of the bracket along the scored line,
score
line
3. Open dishwasher door and place towel over pump
assembly and spray arm of dishwasher, This will
prevent screws from falling into pump area when
securing dishwasher to cabinet,
4. Push the plastic buttons out of the side of the tub,
NOTE: Save the buttons to cover the holes after
dishwasher is installed,
\
5. Push bracket into slot on the side of dishwasher, and
bend tab in towards the side of the dishwasher so that
it keeps the bracket in place,
NOTE: Do not attach the dishwasher, this will be done
later,
tb;a' \
Move dishwasher into cabinet opening
1,
2.
3,
Grasp the sides of the dishwasher
at the edges of the door panel.
Tilt dishwasher backwards on
wheels and move dishwasher close
to cabinet opening. Do not push on
the front of the panel or on the
console--they may dent.
If dishwasher has a power supply
cord, insert power supply cord into hole cut into
cabinet.
4,
If using direct wire, check that it is on the right front
side of opening,
Check that water line is on the left side of opening and
drain hose is near the center of the hole in the cabinet,
5,
Slowly move dishwasher completely into cabinet
opening, Do not kink or pinch copper tubing, drain
hose, power supply cord or direct wire between
dishwasher and cabinet,
6,
He_pfulTip: Once the dishwasher is in position, you
may have to support the front of the dishwasher by
raising, lowering or shimming front feet.
Remove cardboard from under dishwasher,
NOTE: it is all right if dishwasher fits tightly into cabinet
opening, Do not remove insulation blanket --the blanket
reduces the sound level,
12
Check door spring tension
1. With another person holding the dishwasher to prevent
it from tipping, open and close the door a few times. If
the door closes or falls open under its own weight, the
door tension will need to be adjuste&
2. To adjust the door spring tension, unhook the spring
from the rear leg of dishwasher.
3. With a 5/16" nut driver or hex socket, remove the screw
from the tensioner.
4. The screw can be put into one of three holes _, iF41,
in front leg of dishwasher. If the door closes by itself,
move the tensioner to a higher number hole and
replace screw. When door is unlatched, if it opens by
itself, move tensioner to a lower numbered hole and
replace screw.
5. Re-attach door spring to rear leg.Tensioners on both
sides of dishwasher should be secured at same holes.
spdng
ner
screw
LeveU the dishwasher
Align front of dishwasher door panel with cabinet
doors, You may need to adjust alignment to be even
with your cabinets,
HeJpfuITip: Prop up one side of frame to hold
dishwasher up off floor when adjusting front legs,
2. Check that leveling legs are firmly against the floor,
3. Close and latch the door, and place level against the
front panel, Check that dishwasher is plumb, If needed,
adjust leveling leg or add shims under rear wheel until
dishwasher is plumb,
/
J
4. Repeat for other side of dishwasher,
NOTE: Shims must be securely attached to floor to prevent
their movement when the dishwasher is operated,
5. Place level against top front
opening of tub, Check that
dishwasher is level from side to
side, If dishwasher is not level,
adjust front legs up or down until
dishwasher is level,
Make EJectricaJ Connection
Check "Electrical requirements" section,
You need to:
®have the correct electrical supply and recommended
grounding method,
if you are:
o direct wiring, use Option 1
o using a power supply cord, use Option 2
Option 1: Direct wire method
1. Route direct wire so that it does not touch dishwasher
motor or lower part of dishwasher tub.
2. Pull direct wire through hole in terminal box.
He_pfu_ Tip:
o Select the proper size twist-on
connectors to connect your household _._
wiring to 16-gauge dishwasher wiring,
o Insert wire ends into twist-on
connector, Do not pre-twist bare wire,
%/
oTwist connector,
o Gently tug on wires to be sure both
are secured.
3. Connect the wires as follows using twistoon connectors
sized to connect direct wire to 16-gauge dishwasher
wire:
Powersupplywire: Terminalboxwire:
white--white
Nack_black
groundwire_gr0und connector
13
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connecter in
terminal box.
Do not use an extension cord.
Failure to follow these instruct}ons can result }n death,
fire, or emectr}cal shock.
4. Form bare ground wire into a U-shaped hook, Wrap
ground wire hook cJockwise around ground connector
and under the washer.
5. Securely tighten ground connector. Do not untie knot in
the wires.
ground wire washer
ground
connector
/
ground wire
6. Tighten clamp connector or conduit connector screws.
screws
Z Reinstall terminal box cover with wires inside terminal
box,
The cover must be outside the box on the left side,
8. Make sure no wires are pinched by cover.
Option 2: Power supply cord method
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Check that power supply cord does not touch
dishwasher motor or lower part of dishwasher tub.
Connect to water supply
Helpful Tip:
Compression fittings:
a. Slide nut onto copper tubing about 1" (2.5 cm).
b. Slide ferrule onto the tubing. Do not position ferrule
on the end of the tubing.
c. Put the tubing into the elbow as far as it will go.
d. Slide the nut and ferrule forward and start the nut
onto the elbow threads. Be gentle when handling
and positioning the copper tubing, it bends and kinks
easily.
elbow
--....
nut
1. To prevent vibration during operation, route the water
supply line so that it does not touch the dishwasher
base, frame or motor.
2. With copper tubing pushed into compression fitting as
far as it will go, use a wrench and tighten compression
fitting nut to elbow on water inlet valve.
3. Place paper towel under elbow.Turn on water supply
and check for leaks.
14
Connect to drain
1. To heHp minimize
vibration, route drain
hose to avoid contact
with motor, door springs,
water Hine, cabinet,
flooring or the edge of
the hoHe where it passes
through the cabinet.
2. Do not remove drain
Hoop from side of
dishwasher_
3. Hace pan under end of drain hose. Pan wHHcollect any
water in drain hose.
4. Remove pHug and paper from drain connector.
NOTE: Cutting the zip tie hoHding the end of drain hose
in pHace may make maneuvering the drain hose easier
during installation.
zip tie
5. Hace the smaller drain hose
champ onto the small end of the
drain hose.
hose
/J clamp
6. Push the drain hose into the connector up to the stop
on the drain hose,
connector stop
7. Use pliers to open clamp and slide clamp onto
connector between stops on connector as shown,
hose clamp
,j
stops
Secure dishwasher in cabinet opening
Tip Over Hazard
Do not use dishwasher until completely installed,
Do not push down on open door,
Doing so can result in serious iniury or cuts.
1. If you have not already done so, open dishwasher door
and place towel over pump assembly and spray arm of
dishwasher.This will prevent screws from falling into
pump area when securing dishwasher to countertop,
2. Check that dishwasher is still level and centered side to
side in the opening,
3. Secure dishwasher to countertop or sides of cabinet
with two, #10 x 1/2" Phillips-head screws,The
dishwasher must be secured to keep it from tipping
when door is opened, Do not drop screws into bottom
of dishwasher.
OR
4,
Open door about 3 inches (7.6 cm) and check that space
between inner door and tub is equal on both sides. If
spacing is not equal, loosen bracket screws and shift
tub.Tighten bracket screws.
Check that top of door does not contact screws,
brackets, or countertop. If it does, dishwasher must be
lowered and reoleveled.
6. If securing to sides of cabinet, replace the plastic
buttons.
7. Remove towel from dishwasher.
8. Reinstall the lower dishrack
15
Bottom sound pad installation (on somemodels)
1. Remove the bottom sound pad from inside the
dishwasher and take it out of the pHasfic bag.
2. Hace pad on the floor in front of the dishwasher,
making sure Hettering is facing up and vinyH pad faces
down.
3. Foil up and hoH the side paneHs down. Carefully slide
the pad toward the back of the dishwasher as far as it
vviH go, making sure not to push or pull any wires or
hoses. (Do not force.) Side paneHs will open to proper
position.
NOTE: If there are pipes or other obstructions coming
up through the floor, you will need to cut a slit in the
pad to fit around the obstacle.
4. Fold the front end of the pad up into position. Make
sure the vinyl pad is tucked up behind the door and the
dishwasher front legs, as shown.
Complete installation
1. Check that grounding clip is attached to the lower
panel.
2. Place the lower panel behind the access panel. Some
models have insulation on the access panel which must
fall behind the insulation on the lower panel.
grounding
clip
3. Hold the two panels together and peace them against
dishwasher leg.
4. Reinstall the screws through the holes in the access
panel and the slots in the lower panel, install right side
screw first.
/
/
/
5. Check that the lower edge of the lower pane[ contacts
the floor.
6. Tighten the screws.
Direct wire method:
Emectrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box,
Do not use an extension cord,
Failure to follow these instructions can resumt in death,
fire, or e_ectrica_ shock,
Power suppb/cord method:
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or e[ectrica_ shock.
Z Reconnect power or plug in dishwasher.
16
Check operation
1. Read the Use and Care Guide that came with your
dishwasher,
2. Check that aH parts have been installed and no steps
were skipped.
3. Check that you have aH the tooHs you used.
4. Start dishwasher and allow it to compHete the shortest
wash cycle. After the first two minutes, unhtch door,
wait five seconds, then open door.
5. Check to see that there is water in the bottom of the
dishwasher tub. Check that dishwasher is working
properly. If not, see "If dishwasher does not operate"
section.
6. Disconnect power or unpHug dishw, asher.
ff dishwasher does not operate
First try the solutions suggested here to possibly avoid the
cost of a service call.
Has the circuit breaker tripped or the house fuse blown?
Is the door closed tightly and latched?
o Has the cycle been set correctly to start the dishwasher?
Is the water turned on?
If none of these work, call 1-800-422-1230.
17
18
Table des matieres
Secur[t_ du [ave-va[sse[[e ........................... 19
Exigences d'insta[[at[on ............................ 20
OutH[age et pieces ............................. 20
Emplacement dqnstaHat[on ...................... 20
Specifications de
[a canaHsafion d'evacuaNon ..................... 22
Specifications de
['aHmentafion en eau ........................... 22
Specifications e[ectdques ....................... 22
Instructions d'[nsta[[at[on .......................... 23
Preparation des ouvertures dans Hes pHacards -
utH[safion des modes de raccordement existants pour
cana[isations et c_b[age ......................... 23
Preparation de ['emplacement d'insta[[ation entre [es
placards [orsque [es cana[isations et c_b[es n'ont pas
et6 instaHes .................................. 24
Preparation du [ave-vaisse[[e .................... 26
Raccordement e[ectrique ........................ 30
Raccordement _ [a cana[isation d'eau ............. 31
Raccordement a la canaiisation d'evacuation ....... 32
Immobiiisation du lave-vaisseiie dans I'espace
d'instaiiation .................................. 32
Securite du iaveovaisseHe
Votre s_curit_ et celle des autres est tres importante.
Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de
toujours life tousles messages de securite et de vous y conformer.
Voici le symbole d'alerte de securit&
Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous
et &d'autres.
Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de deces ou de blessure grave si vous ne
suivez pas immediatement les instructions.
Risque possible de deces ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Risque de bascumement
Ne pas uti[iser [e [ave=vaisseHe jusqu'a ce qu'H soit
comp[etement instaHe,
Ne pas appuyer sur maporte ouverte,
Le non-respect de ces instructions peut causer des
blessures graves ou des coupures,
Tenir compte de ceci :
Ouvrir [entement [a porte du [ave-vaisse[[e tandis qu'une
autre personne saisit ['arriere de ['appareiL Retirer [es
materiaux d'emba[[age, [e tuyau de decharge et[e panier
inferieur, Fermer [a porte du [ave°vaisse[[e et verroui[[er [e
[oquet.
oRespecter [es dispositions de tous[es codes et reg[ements
en vigueur.
Installer le hve-vaisselle conformement aux prescriptions
des presentes instructions,
o Einsta[[ation devrait _tre execut6e par un technicien
qua[ifi& Vei[[er a respecter [es dispositions de tous [es
codes et reg[ements [ocaux et nationaux regissant [es
installations de p[omberie et d%[ectricit&
19
Exigences d'instMiation
Outi[[age et pi ces
Rassennbier tous [es outHs et pieces necessaires avant de
commencer [qnstaHation. Lire et suivre [es instructions
fournies avec [es outHs indiqu6s ici.
Pour toutes [es configurations d'insta[[ation
Outi[[age necessaire
o pince
tournevis Phillips
®tourne-ecrou ou c[e
douille - douilbs
hexagonales 5/16" ou 1/4"
nnetre-ruban ou reg[e
o c[e a nnoiette de 10"
(ouverture jusqu'_ 2,9 cnn
[1 1/8"])
*tournevis _ [anne plate
®couteau utilitaire
2 connecteurs de fils de
taille appropriee pour le
raccordennent des
conducteurs de I'appareil
(calibre 16) au cablage de
la nnaison
®petit niveau
tournevisTORX T15
(en cas d'installation de
panneaux avant
personna[ises
* lannpe torche
®plat peu profond
o perceuse electrique avec
foret de 3/32"
o cle plate 5/8"
®serviette de bain
cab de bois
Pieces necessaires :
raccord 90 ° avec filetage
externe de 3/8" NPT a une
extrennit6. (La configuration
de I'autre extr6nnite doit
&tre adaptee a celle de la
canalisation d'arrivee
d'eau.)
ruban deTeflon _ou
connpose d'6tanch6ite pour
tuyauteries
®cabs (pour I'installation
sur un plancher
rehaussennent partiel)
4 vis a bois n° 10 x 1/2"
(en cas d'installation de
panneaux avant
personnalises
OutHlage et pi@,cessupp[ementaires pour
Finsta[[ation dans un local neuf
Outi[[age necessaire :
perceuse electrique avec
scies a trous de 1/2", 3/4" et
1 1/2"
petit coupe4ube
o pince a denuder
bride de tuyau a via 1 1/2"
- 2" pour raccordement
la canalisation d%gout sur
un raccord T
Pieces necessaires :
tube de cuivre (3/8"
reconnnnande) ou conduit
de raccordennent flexible
avec tresse d'acier
inoxydable
serre°c_ble ou connecteur
de conduit utilisable sur
un trou de diannetre
2,2 cnn (7/8"}
Pieces foumies
A. 2 brides pour tuyau de decharge - 1 grosse, 1 petite
B. 2 vis Phillips n° 10 x 1/2"
C.Tuyau de decharge
A B
Pi&ces additionnelles fournies uniquement avec les
nnodeles _ evacuation par le haut
D. 2 via n ° 8 x 1-3/8"TQRX T15
E. 4 vis _ t&te hexagonale n° 10 x 3/8"
(_.Teflonest une marque depos6e de Du Pont de Nemours and Company.
(_Marque depos_.edeTEXTRON
20
Pieces supplementaires fournies avec certains nnodeles
F. Coussinet du bas (situe dana le panier superieur)
Verifier la presence de toutes ces pieces. Si I'une des
pi6ces mentionnees n'est pas presente, telephoner au
1-800_422q 230.
Voir la liste separ6e des pieces et accessoires disponibles
pour le lave-vaisselle,
Emplacement d'insta[[ation
Ne pas placer canalisation d%vacuation, canalisation d'eau
ou cablage electrique a un endroit ou cela susciterait
interference ou contact avec les pieds ou le nnoteur du
laveovaisselle.
A I'ennplacennent d'installation du laveovaisselle0 on doit
pouvoir etablir le degagement approprie entre le nnoteur et
le plancher. Le moteur ne doit pas toucher le plancher.
Ne pas installer le lave°vaisselle par-dessus un tapis.
Proteger du gel le lave°vaisselle et les canalisations d'eau
qui I'alinnentent; la garantie de I'appareil ne couvre pas lea
donnnnages innputables au gel.
Un ensennbie "panneau lateral" est disponible chez les
revendeurs pour I'installation du laveovaisselle
I'extrennite d'une rangee de placards.
Un accessoire pare-vapeur (produit n° 4396277) est
disponible chez les revendeurs pour I'installation de
I'appareil sous le plan de travail. Cependant I'utilisation de
cet accessoire n'est pas indispensable. On peut egalennent
commander ce produit par telephone au 1-800-422q230.
[nspecter I'ennplacennent d'installation du lave-vaisselle; il
doit connporter les caracteristiques suivantes :
faciiit& d'acces aux canaiisations d'eau et d%gout eta la
source d'electricite.
acces facile pour chargennent et dechargement de la
vaisselle. Dans le cas de I'installation dans un angle, on
doit pouvoir etablir un degagennent de 5,1 cm (2") ou plus
entre le c6te de la porte du lave-vaisselle et le nnur ou le
placard.
ouverture carree offrant I'esthetique appropriee et
permettant un fonctionnennent correct.
facade des placards perpendiculaire au plancher.
plancher horizontal et plat (s'il y a un ecart de niveau
entre I'avant et I'arriere sur le plancher de I'ennplacennent
d'installation, il pourrait 8tre necessaire d'utiliser des
cales pour etablir I'aplonnb de I'appareil).
NOTE : Pour eviter tout deplacennent des cabs durant le
fonctionnennent de I'appareil, il eat necessaire de fixer lea
cabs au plancher.
Si le lave-vaisselle ne doit pas _tre utilise pendant une
periode prolongee ou s'il est laisse a un endroit qui
pourrait &tre expose au gel, veiller a faire executer les
operations de pre-hivernage par un technicien connpetent.
Veiller _ ce que les canalisations d'eau et d'evacuation et
les cables electriques soient dans la zone nnarquee en gris
dans la section "Dimensions de I'emplacennent
d'installation':
Consei[ utile : Si le plancher de I'espace d'installation
n'est pas parfaitennent horizontal et plat (exennple :
garnissage de carrelage sur une pantie seulennent), on
devra accorder une attention particuliere aux details
iors du releve des dimensions, pour pouvoir etablir
I'aplonnb correct du lave-vaisselle.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
KitchenAid KUDC02IRBL0 Guide d'installation
- Catégorie
- Lave-vaisselle
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
Autres documents
-
Kenmore 66513206K902 Guide d'installation
-
Whirlpool GU3200XTVY1 Guide d'installation
-
Kenmore 66517032402 Guide d'installation
-
Inglis TUD8750SD1 Guide d'installation
-
Kenmore 66513772K604 Guide d'installation
-
IKEA IUD9750WS0 Guide d'installation
-
-
Roper DU1050XTPS7 Guide d'installation
-
Roper Dishwasher Undercounter Dishwasher Manuel utilisateur
-
Whirlpool UDT518SAFP Guide d'installation