Olympus 500 Manuel utilisateur

DIGITAL CAMERA

Shoot and Play!

B

a

s

i

c

M

a

n

u

a

l

2

26

50

74

ENGLISH

FRANCAIS

ESPAÑOL

DEUTSCH

d4221_basic_e_00_bookfile_7.book Page 1 Monday, October 25, 2004 7:37 PM

2

En

For customers in North and South America

For customers in Europe

“CE” mark indicates that this product complies with the European requirements

for safety, health, environment and customer protection. “CE” mark cameras

are intended for sales in Europe.

For customers in USA

Declaration of Conformity

Model Number : Stylus 500/

Trade Name : OLYMPUS

Responsible Party :

Address : Two Corporate Center Drive, PO Box 9058, Melville, NY

11747-9058 U.S.A.

Telephone Number : 1-631-844-5000

Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation.

FCC Notice

• Radio and Television Interference

Change or modifications not expressly approved by the manufacturer may void the

user’s authority to operate this equipment. This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference

in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- Adjust or relocate the receiving antenna.

- Increase the distance between the camera and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

- Consult your dealer or an experienced radio/TV technician for help. Only the

OLYMPUS-supplied USB or cable should be used to connect the camera to USB

enabled personal computers (PC).

Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

For customers in Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

d4221_basic_e_00_bookfile_7.book Page 2 Monday, October 25, 2004 7:37 PM

3

En

Manual Contents

How to use the camera .................................................. 4

Safety Precautions ......................................................... 6

Weatherproof feature ..................................................... 9

UNPACKING THE BOX CONTENTS...................10

CHARGING THE BATTERY .............................12

INSERTING THE BATTERY AND CARD ..............13

TURNING THE CAMERA ON ...........................16

TAKING A PICTURE......................................18

REVIEWING A PICTURE ................................20

TURNING THE CAMERA OFF ..........................21

Specifications ............................................................... 22

d4221_basic_e_00_bookfile_7.book Page 3 Monday, October 25, 2004 7:37 PM

4

En

Navigation

How to use the camera

Using a card...

Pictures taken with this

camera are stored on a

xD-Picture Card. By

storing the relevant print

reservation data with the

images on the card, you

can print pictures at a

photo shop or on a

PictBridge-compatible

printer.

Using a computer...

Using the OLYMPUS Master

software on your computer lets you

enjoy editing, viewing, and printing

the pictures downloaded from your

camera.

Using a printer...

With a PictBridge-compatible

printer, you can print pictures

directly from your camera.

Using a TV...

You can use a TV to view

pictures or playback

movies from your camera.

d4221_basic_e_00_bookfile_7.book Page 4 Monday, October 25, 2004 7:37 PM

5

En

Using the arrow pad and e

button...

The arrow pad and e button are for

selecting and setting menu options as well

as viewing pictures frame by frame.

PRINT MODE SELECT

PRINT

ALL PRINT

MULTI PRINT

ALL INDEX

SELECT

GO

OK

EXIT

DRIVE

ESP㧛5

ISO

AF MODE

CARD

SET

CAMERA

AUTO

SPOT

OFF

ESP

DIGITAL ZOOM

Using the menus...

Shooting and playback-related

functions are set from the menus

displayed on the monitor.

Using the mode dial...

Use the mode dial to select a shooting or

playback mode.

Using the direct buttons...

f lets you select the optimum settings

for the shooting conditions.

Direct buttons also let you perform functions

such as setting the flash mode or taking the

close-up pictures or self-timer, making

camera operation easy.

d4221_basic_e_00_bookfile_7.book Page 5 Monday, October 25, 2004 7:37 PM

6

En

Safety Precautions

Read All Instructions — Before you use the product, read all operating

instructions.

Save These Instructions — Save all safety and operating instructions for future

reference.

Heed Warnings — Read carefully and follow all warning labels on the product and

those described in the instructions.

Follow Instructions — Follow all instructions provided with this product.

Cleaning — Always unplug this product from the wall outlet before cleaning. Use

only a damp cloth for cleaning. Never use any type of liquid or aerosol cleaner,

or any type of organic solvent to clean this product.

Attachments — For your safety, and to avoid damaging the product, use only

accessories recommended by Olympus.

Water and Moisture — Never use this product around water (near a bathtub,

kitchen sink, laundry tub, wet basement, swimming pool or in the rain). For

precautions on products with weatherproof designs, read the weatherproofing

sections of their manuals.

Location — To avoid damage to the product and prevent personal injury, never

place this product on an unstable stand, tripod, bracket, table or cart. Mount

only on a stable tripod, stand, or bracket. Follow the instructions that describe

how to safely mount the product, and use only the mounting devices

recommended by the manufacturer.

Power Sources — Connect this product only to the power source described on

the product label. If you are not sure about the type of power supply in your

home, consult your local power company. Refer to your operating instructions

for information on using the product with a battery.

Grounding, Polarization — If this product can be used with a specified AC

adapter, the adapter may be equipped with a polarized alternating current line

General Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED OLYMPUS SERVICE PERSONNEL.

Lightning flash with an arrowhead, enclosed in a triangle, alerts you to the presence of uninsulated voltage

points inside the product which could cause a serious electrical shock.

An exclamation mark enclosed in a triangle alerts you to important operating and maintenance instructions in

the documentation provided with the product.

WARNING!

TO AVOID THE RISK OF FIRE OR ELECTRICAL SHOCK, NEVER EXPOSE THIS PRODUCT TO WATER OR

OPERATE IN A HIGH HUMIDITY ENVIRONMENT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

d4221_basic_e_00_bookfile_7.book Page 6 Monday, October 25, 2004 7:37 PM

Safety Precautions

7

En

plug (a plug with one blade wider than the other). This safety feature allows the

plug to fit into the power outlet only one way. If you cannot insert the plug into

the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to

fit, contact an electrician and have the receptacle replaced.

Protecting the Power Cord — The power supply cord should be placed so it will

not be walked on. Never put a heavy object on the power cord or wrap it around

the leg of a table or chair. Keep the area around the power cord connection

points, at the power outlet, and at the product connection, free of all AC adapter

or accessory power cords.

Lightning — If a lightning storm occurs while using the specified AC adapter,

unplug it from the wall outlet immediately. To avoid damage from unexpected

power surges, always unplug the AC adapter from the power outlet and

disconnect it from the camera when the camera is not in use.

Overloading — Never overload wall outlets, extension cords, power strips, or

other power connection points with too many plugs.

Foreign Objects, Liquid Spillage — To avoid personal injury caused by fire or

electrical shock from contact with internal high voltage points, never insert a

metal object into the product. Avoid using the product where there is a danger

of spillage.

Heat — Never use or store this product near any heat source such as a radiator,

heat register, stove, or any type of equipment or appliance that generates heat,

including stereo amplifiers.

Servicing — Refer all servicing to qualified personnel. Attempting to remove the

covers or disassemble the product, could expose you to dangerous high

voltage points.

Damage Requiring Service — If you notice any of the conditions described below

while using the specified AC adapter, unplug it from the wall outlet and refer

servicing to qualified service personnel:

a) Liquid has been spilled onto the product or some other object has fallen into

the product.

b) The product has been exposed to water.

c) The product does not operate normally despite following operating

instructions. Adjust only the controls described in the operating instructions

as improper adjustment of other controls could damage the product and

require extensive repair work by a qualified technician.

d) The product has been dropped or damaged in any way.

e) The product exhibits a distinct change in performance.

Replacement Parts — When replacement parts are required, make sure that the

service center uses only parts with the same characteristics as the originals, as

recommended by the manufacturer. Unauthorized substitution of parts could

result in fire, electrical shock, or create other hazards.

Safety Check — Upon completion of servicing or repairs, ask the service

technician to perform safety checks to determine that the product is in good

working order.

d4221_basic_e_00_bookfile_7.book Page 7 Monday, October 25, 2004 7:37 PM

Safety Precautions

8

En

Legal and other notices

• Olympus makes no representations or warranties regarding any damages, or

benefit expected by using this unit lawfully, or any request from a third person,

which are caused by the inappropriate use of this product.

• Olympus makes no representations or warranties regarding any damages or

any benefit expected by using this unit lawfully which are caused by erasing

picture data.

Disclaimer of Warranty

• Olympus makes no representations or warranties, either expressed or implied,

by or concerning any content of these written materials or software, and in no

event shall be liable for any implied warranty of merchantability or fitness for any

particular purpose or for any consequential, incidental or indirect damages

(including but not limited to damages for loss of business profits, business

interruption and loss of business information) arising from the use or inability to

use these written materials or software or equipment. Some countries do not

allow the exclusion or limitation of liability for consequential or incidental

damages, so the above limitations may not apply to you.

• Olympus reserves all rights to this manual.

WARNING

Unauthorized photographing or use of copyrighted material may violate applicable

copyright laws. Olympus assumes no responsibility for unauthorized

photographing, use or other acts that infringe upon the rights of copyright owners.

Copyright Notice

reproduced or used in any form or by any means, electronic or mechanical,

including photocopying and recording or the use of any type of information storage

and retrieval system, without the prior written permission of Olympus. No liability

is assumed with respect to the use of the information contained in these written

materials or software, or for damages resulting from the use of the information

contained therein. Olympus reserves the right to alter the features and contents of

this publication or software without obligation or advance notice.

Trademarks

• IBM is a registered trademark of International Business Machines Corporation.

• Microsoft and Windows are registered trademarks of Microsoft Corporation.

• Macintosh is a trademark of Apple Computer Inc.

• All other company and product names are registered trademarks and/or

trademarks of their respective owners.

• The standards for camera file systems referred to in this manual are the “Design

Rule for Camera File System/DCF” standards stipulated by the Japan

Electronics and Information Technology Industries Association (JEITA).

d4221_basic_e_00_bookfile_7.book Page 8 Monday, October 25, 2004 7:37 PM

9

En

Weatherproof feature

This camera is weatherproof, but it cannot be used underwater.

Olympus will not assume any responsibility for malfunction of the camera

caused by water getting inside as a result of misuse by the user.

The camera is weatherproof and is not damaged by water spray from any

direction.

Observe the following precautions when using the camera.

Water may get inside the camera if the battery compartment/card cover or

connector cover are not firmly closed so close them firmly.

• If the camera gets splashed, wipe the water off as soon as possible with

a dry cloth.

• The rechargeable battery and other camera accessories are not

weatherproof.

Do not wash the

camera with water.

Do not drop the

camera into water.

Do not take pictures

underwater.

Battery compartment/

card cover

o

n

Connector

cover

d4221_basic_e_00_bookfile_7.book Page 9 Monday, October 25, 2004 7:37 PM

10

En

UNPACKING THE BOX CONTENTS

If you find any contents missing or damaged, contact the place of purchase.

Contents vary depending on the area where you purchased this camera.

Digital Camera Strap

Card

LI-12B Lithium Ion Battery LI-10C Battery Charger

USB Cable

AV Cable

OLYMPUS Master CD-ROM

Basic Manual (this manual)

Advanced Manual

(CD-ROM)

Warranty Card

Registration Card

d4221_basic_e_00_bookfile_7.book Page 10 Monday, October 25, 2004 7:37 PM

UNPACKING THE BOX CONTENTS

11

En

1

Attach the strap as shown.

Note

Be careful with the strap when you carry the camera, as it can easily catch on

stray objects, causing injury or damage.

Do not swing the camera around by the strap or pull the strap with excessive

force as this may cause the strap to break.

Attach the strap correctly as shown above so that the camera does not fall off.

If the strap is attached incorrectly and the camera falls off, Olympus is not

responsible for any damages.

Attaching the strap

Pull the strap tight so that it does not come loose.

d4221_basic_e_00_bookfile_7.book Page 11 Monday, October 25, 2004 7:37 PM

12

En

CHARGING THE BATTERY

The battery is not fully charged at the time of purchase. Charge the

battery fully with the LI-10C charger before use.

1

Connect the power cable.

2

Insert the battery into the charger.

TIPS

The LI-12B battery takes approximately 120 minutes to charge.

Note

This camera uses an Olympus LI-12B/LI-10B lithium ion battery. No other

type of battery can be used.

Use only the specified charger.

Battery life varies depending on shooting conditions, etc.

The charger can be used within the range of AC100V to AC240V (50/60Hz).

When using the charger abroad, you may need a plug adapter to convert the

plug to the shape of the AC wall outlet. For details, ask at your local electrical

shop or travel agent.

Do not use voltage converters sold in stores traveling overseas as this could

damage your charger.

LI-10C battery charger

Power cable

AC wall outlet

n

o

S mark

LI-12B

lithium ion battery

Charging indicator

When charging starts, the indicator lights red.

When fully charged, the indicator turns green.

d4221_basic_e_00_bookfile_7.book Page 12 Monday, October 25, 2004 7:37 PM

13

En

INSERTING THE BATTERY AND CARD

1

Make sure the camera is off.

2

Open the battery compartment/card cover.

3

Insert the battery.

The lens is retracted.

The monitor is off.

The lamp is off.

Battery compartment/card cover

Slide

Lift

o

n

Battery lock knob

To remove the battery

Slide the lock knob as

shown. The battery pops up

allowing you to grasp it.

Battery lock

knob

The battery is locked into place

when inserted correctly.

d4221_basic_e_00_bookfile_7.book Page 13 Monday, October 25, 2004 7:37 PM

INSERTING THE BATTERY AND CARD

14

En

4

Insert the card.

Note

The card may not record properly if it is not inserted all the way in.

Releasing your finger quickly after pushing the card all the way in may

cause it to eject forcefully out of the slot.

5

Close the battery compartment/card cover.

Â

Notch

Index area

Make sure that the card is

oriented correctly and

insert until it clicks while

keeping it straight,

otherwise the contacts on

the card may be damaged

or the card may get stuck.

Grasp and remove.

To remove the card

Push the card all the way in and

release slowly.

Close

Slide

o

n

Press down on the center of the cover when sliding.

d4221_basic_e_00_bookfile_7.book Page 14 Monday, October 25, 2004 7:37 PM

INSERTING THE BATTERY AND CARD

15

En

Note

The amount of power consumed by the camera varies considerably

depending on shooting conditions, etc.

Power is consumed continuously during the conditions described below. This

discourages the power from lasting longer.

When the monitor is in playback mode for an extended period of time.

Repeated zoom adjustments.

Repeated auto focus by depressing the shutter button halfway.

When connected to a computer or printer.

If you use an exhausted battery, the camera may turn off without displaying

the battery level warning.

This camera uses an xD-Picture Card (16 – 512MB).

Note

This camera may not recognize a non-OLYMPUS card or a card that was

formatted on another device (such as a computer, etc.). Before use, be sure

to format the card on this camera.

Do not press on the card with hard or pointed items such as ballpoint pens.

Never open the battery compartment/card cover, or remove the card or the

battery while the camera is turned on. Doing so could destroy the data stored

on the card. Once destroyed, data cannot be restored.

Do not place a sticker or label on the card as this could prevent the card from

being ejected.

The battery

The card

Index area

You can use this space to write the contents of the card.

Contacts

The part where the data transferred from the camera

enters the card.

d4221_basic_e_00_bookfile_7.book Page 15 Monday, October 25, 2004 7:37 PM

16

En

TURNING THE CAMERA ON

1

Set the mode dial to K and press the POWER

switch.

Note

To save battery power, the camera automatically enters the sleep mode and

stops operating after about 3 minutes of non-operation. The camera activates

again as soon as you operate the shutter button or zoom button.

15 minutes after the camera enters sleep mode, the camera retracts the lens

and turns off automatically. Turn the camera on to use.

HQ

2560

1920

30

o

Mode dial

POWER switch

Battery check indicator

Shooting scene/Shooting mode

The lens extends and the

monitor turns on.

d4221_basic_e_00_bookfile_7.book Page 16 Monday, October 25, 2004 7:37 PM

TURNING THE CAMERA ON

17

En

The battery check indicator changes according to how much power is

remaining.

The first time you use the camera, "Y/M/D"

is displayed prompting you to enter the date

and time. See "Setting the date and time" in

Chapter 7 of the Advanced Manual. The

camera operates without making this

setting.

The language for on-screen display varies

depending on the area where you

purchased this camera. The language for

on-screen display in Basic Manual and

Advanced Manual is the same as the box

description. To change the language, refer

to the "Selecting a language" in Chapter 7

of the Advanced Manual.

Turning on the camera for the first time

Battery power

Lit (green)

(Disappears after a while.)

Ready to shoot.

No power is left. Charge the

battery.

Blinking (red)

The battery needs charging

soon.

ef

“BATTERY EMPTY”

is displayed.

Setting the date and time

Y/M/D

Language for on-screen display

ENGLISH

FRANCAIS

PORTUGUES

ESPAÑOL

SELECT GO

OK

d4221_basic_e_00_bookfile_7.book Page 17 Monday, October 25, 2004 7:37 PM

18

En

TAKING A PICTURE

1

Compose your picture.

2

Focus on your subject.

HQ

30

2560

1920

o

AF target mark

Using the monitor, place the AF

target mark on your subject.

Shutter button

Lamp

HQ

30

2560

1920

o

2560

1920

o

# mark

Green lamp

The green lamp lights when the

focus and exposure are locked

(Focus lock).

The # mark lights when the

flash is about to fire.

Press the shutter button

halfway and hold.

d4221_basic_e_00_bookfile_7.book Page 18 Monday, October 25, 2004 7:37 PM

TAKING A PICTURE

19

En

3

Take the picture.

Note

Press the shutter button gently. If it is pressed hard, the camera may move

and pictures may come out blurred.

Never open the battery compartment/card cover, remove the battery or

disconnect the AC adapter while the lamp on the camera is blinking red. Doing

so could destroy stored pictures and prevent storage of pictures you have just

taken.

Recorded pictures are saved on the card regardless of whether the camera

is turned off or the battery is replaced or removed.

When taking pictures against strong backlight, the area of the picture in

shadow may appear colored.

Every time you press the shutter button, the memory gauge lights indicating

that the picture you have just taken is being recorded onto the card. The

memory gauge changes according to how many pictures the camera is

processing. This indicator is not displayed while recording movies.

The lamp on the camera blinks

red while the picture is recorded

onto the card.

HQ

30

2560

1920

o

2560

1920

o

b

Memory gauge

Press the shutter button

completely.

Memory gauge

a b c d

Before taking

any pictures

(Off)

Maximum reached

(All lit)

Wait until the indicator

turns off again before

taking more pictures.

After taking one

picture

(Lit)

After taking

several pictures

(Lit)

Shoot Shoot Shoot

Wait

d4221_basic_e_00_bookfile_7.book Page 19 Monday, October 25, 2004 7:37 PM

20

En

REVIEWING A PICTURE

1

Press the QUICK VIEW button.

2

Use the arrow pad to display the picture you want.

HQ

100

-

0030

$05.02.16 15:30

30

You can display the last picture

you took while staying in any

shooting mode.

Press the QUICK VIEW button

again or press the shutter

button lightly when you are

ready to take another picture.

QUICK VIEW button

Next picture

Previous picture

10 pictures back

10 pictures forward

d4221_basic_e_00_bookfile_7.book Page 20 Monday, October 25, 2004 7:37 PM

La page charge ...

Olympus 500 Manuel utilisateur

Olympus 500 Manuel utilisateur

dans d''autres langues

Documents connexes