ESAB PCM-750i Manuel utilisateur

Marque: ESAB

Modèle: PCM-750i

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

PCM-750i Plasma Arc Cutting Package

Be sure this information reaches the operator.

You can get extra copies through your supplier.

INSTRUCTION MANUAL

PCM-750i

PLASMA ARC CUTTING PACKAGE

Series A

This manual provides installation and operation instructions for the following PCM-750i (Series A) cutting packages:

P/N 33980 - 230 V, 1-Phase

P/N 33982 - 460 V, 3-Phase

Starting with Serial No. PORI509000

F-15-223-A

February, 1996

These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and

safe practices for electric welding equipment, we urge you to read our booklet, "Precautions and Safe Practices for

Arc Welding, Cutting, and Gouging," Form 52-529. Do NOT permit untrained persons to install, operate, or maintain

this equipment. Do NOT attempt to install or operate this equipment until you have read and fully understand these

instructions. If you do not fully understand these instructions, contact your supplier for further information. Be sure

to read the Safety Precautions before installing or operating this equipment.

USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and accompanying

labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions pro-

vided. This equipment must be checked periodically. Defective equipment should not be used. Parts that are

broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair or replace-

ment become necessary, the manufacturer recommends that a telephone or written request for service advice be

made to the Authorized Distributor from whom purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The

user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty

maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility

designated by the manufacturer.

TABLE OF CONTENTS

SECTION TITLE PAGE

PARAGRAPH

SECTION 1 DESCRIPTION ................................................................................................. 5

1.1 General ............................................................................................................. 5

1.2 Scope................................................................................................................ 5

1.3 Packages Available........................................................................................... 5

1.4 Specifications.................................................................................................... 6

SECTION 2 INSTALLATION................................................................................................ 8

2.1 General ............................................................................................................. 8

2.2 Equipment Required ......................................................................................... 8

2.3 Location ............................................................................................................ 8

2.4 Inspection.......................................................................................................... 8

2.5 Primary Electrical Input Connections................................................................. 8

SECTION 3 OPERATION..................................................................................................... 11

3.1 Operation .......................................................................................................... 11

3.2 PCM-750i Controls............................................................................................ 11

3.3 Cutting with the PT-27....................................................................................... 11

3.4 Common Cutting Problems ............................................................................... 13

SECTION 4 MAINTENANCE ............................................................................................... 14

4.1 General ............................................................................................................. 14

4.2 Inspection and Cleaning.................................................................................... 14

4.3 PT-27 Torch Consumable Parts........................................................................ 14

4.4 Flow Switch....................................................................................................... 15

SECTION 5 TROUBLESHOOTING ..................................................................................... 16

5.1 Troubleshooting ................................................................................................ 16

5.2 Troubleshooting Guide ...................................................................................... 16

SECTION 6 REPLACEMENT PARTS ................................................................................. 27

6.1 General ............................................................................................................. 27

6.2 Ordering ............................................................................................................ 27

WARNING: These Safety Precautions are for

your protection. They summarize precaution-

ary information from the references listed in

Additional Safety Information section. Before

performing any installation or operating procedures, be

sure to read and follow the safety precautions listed below

as well as all other manuals, material safety data sheets,

labels, etc. Failure to observe Safety Precautions can result

in injury or death.

PROTECT YOURSELF AND OTHERS --

Some welding, cutting, and gouging

processes are noisy and require ear

protection. The arc, like the sun, emits

ultraviolet (UV) and other radiation and

can injure skin and eyes. Hot metal can cause burns.

Training in the proper use of the processes and equip-

ment is essential to prevent accidents. Therefore:

1. Always wear safety glasses with side shields in any work

area, even if welding helmets, face shields, and goggles

are also required.

2. Use a face shield fitted with the correct filter and cover

plates to protect your eyes, face, neck, and ears from

sparks and rays of the arc when operating or observing

operations. Warn bystanders not to watch the arc and

not to expose themselves to the rays of the electric-arc

or hot metal.

3. Wear flameproof gauntlet type gloves, heavy long-sleeve

shirt, cuffless trousers, high-topped shoes, and a weld-

ing helmet or cap for hair protection, to protect against

arc rays and hot sparks or hot metal. A flameproof apron

may also be desirable as protection against radiated

heat and sparks.

4. Hot sparks or metal can lodge in rolled up sleeves,

trouser cuffs, or pockets. Sleeves and collars should be

kept buttoned, and open pockets eliminated from the

front of clothing

5. Protect other personnel from arc rays and hot sparks

with a suitable non-flammable partition or curtains.

6. Use goggles over safety glasses when chipping slag or

grinding. Chipped slag may be hot and can fly far.

Bystanders should also wear goggles over safety glasses.

FIRES AND EXPLOSIONS -- Heat from

flames and arcs can start fires. Hot slag

or sparks can also cause fires and ex-

plosions. Therefore:

1. Remove all combustible materials well away from the

work area or cover the materials with a protective non-

flammable covering. Combustible materials include wood,

cloth, sawdust, liquid and gas fuels, solvents, paints and

coatings, paper, etc.

2. Hot sparks or hot metal can fall through cracks or

crevices in floors or wall openings and cause a hidden

smoldering fire or fires on the floor below. Make certain

that such openings are protected from hot sparks and

metal.“

3. Do not weld, cut or perform other hot work until the

workpiece has been completely cleaned so that there

are no substances on the workpiece which might pro-

duce flammable or toxic vapors. Do not do hot work on

closed containers. They may explode.

4. Have fire extinguishing equipment handy for instant use,

such as a garden hose, water pail, sand bucket, or

portable fire extinguisher. Be sure you are trained in its

use.

SAFETY PRECAUTIONS

10/98

5. Do not use equipment beyond its ratings. For example,

overloaded welding cable can overheat and create a fire

hazard.

6. After completing operations, inspect the work area to

make certain there are no hot sparks or hot metal which

could cause a later fire. Use fire watchers when neces-

sary.

7. For additional information, refer to NFPA Standard 51B,

"Fire Prevention in Use of Cutting and Welding Pro-

cesses", available from the National Fire Protection Asso-

ciation, Batterymarch Park, Quincy, MA 02269.

ELECTRICAL SHOCK -- Contact with live

electrical parts and ground can cause

severe injury or death. DO NOT use AC

welding current in damp areas, if move-

ment is confined, or if there is danger of

falling.

1. Be sure the power source frame (chassis) is connected

to the ground system of the input power.

2. Connect the workpiece to a good electrical ground.

3. Connect the work cable to the workpiece. A poor or

missing connection can expose you or others to a fatal

shock.

4. Use well-maintained equipment. Replace worn or dam-

aged cables.

5. Keep everything dry, including clothing, work area, cables,

torch/electrode holder, and power source.

6. Make sure that all parts of your body are insulated from

work and from ground.

7. Do not stand directly on metal or the earth while working

in tight quarters or a damp area; stand on dry boards or

an insulating platform and wear rubber-soled shoes.

8. Put on dry, hole-free gloves before turning on the power.

9. Turn off the power before removing your gloves.

10. Refer to ANSI/ASC Standard Z49.1 (listed on next page)

for specific grounding recommendations. Do not mistake

the work lead for a ground cable.

ELECTRIC AND MAGNETIC FIELDS —

May be dangerous. Electric current flow-

ing through any conductor causes lo-

calized Electric and Magnetic Fields

(EMF). Welding and cutting current cre-

ates EMF around welding cables and

welding machines. Therefore:

1. Welders having pacemakers should consult their physi-

cian before welding. EMF may interfere with some pace-

makers.

2. Exposure to EMF may have other health effects which are

unknown.

3. Welders should use the following procedures to minimize

exposure to EMF:

A. Route the electrode and work cables together. Secure

them with tape when possible.

B. Never coil the torch or work cable around your body.

C. Do not place your body between the torch and work

cables. Route cables on the same side of your body.

D. Connect the work cable to the workpiece as close as

possible to the area being welded.

E. Keep welding power source and cables as far away

from your body as possible.

FUMES AND GASES -- Fumes and

gases, can cause discomfort or harm,

particularly in confined spaces. Do

not breathe fumes and gases. Shield-

ing gases can cause asphyxiation.

Therefore:

1. Always provide adequate ventilation in the work area by

natural or mechanical means. Do not weld, cut, or gouge

on materials such as galvanized steel, stainless steel,

copper, zinc, lead, beryllium, or cadmium unless positive

mechanical ventilation is provided. Do not breathe fumes

from these materials.

2. Do not operate near degreasing and spraying opera-

tions. The heat or arc rays can react with chlorinated

hydrocarbon vapors to form phosgene, a highly toxic

gas, and other irritant gases.

3. If you develop momentary eye, nose, or throat irritation

while operating, this is an indication that ventilation is not

adequate. Stop work and take necessary steps to im-

prove ventilation in the work area. Do not continue to

operate if physical discomfort persists.

4. Refer to ANSI/ASC Standard Z49.1 (see listing below)

for specific ventilation recommendations.

5. WARNING: This product, when used for welding or

cutting, produces fumes or gases which

contain chemicals known to the State of

California to cause birth defects and, in

some cases, cancer. (California Health &

Safety Code

§25249.5 et seq.)

CYLINDER HANDLING -- Cylinders, if

mishandled, can rupture and violently

release gas. Sudden rupture of cylin-

der, valve, or relief device can injure or

kill. Therefore:

1. Use the proper gas for the process and use the proper

pressure reducing regulator designed to operate from

the compressed gas cylinder. Do not use adaptors.

Maintain hoses and fittings in good condition. Follow

manufacturer's operating instructions for mounting regu-

lator to a compressed gas cylinder.

2. Always secure cylinders in an upright position by chain

or strap to suitable hand trucks, undercarriages, benches,

walls, post, or racks. Never secure cylinders to work

tables or fixtures where they may become part of an

electrical circuit.

3. When not in use, keep cylinder valves closed. Have

valve protection cap in place if regulator is not con-

nected. Secure and move cylinders by using suitable

hand trucks. Avoid rough handling of cylinders.

4. Locate cylinders away from heat, sparks, and flames.

Never strike an arc on a cylinder.

5. For additional information, refer to CGA Standard P-1,

"Precautions for Safe Handling of Compressed Gases in

Cylinders", which is available from Compressed Gas

Association, 1235 Jefferson Davis Highway, Arlington,

VA 22202.

EQUIPMENT MAINTENANCE -- Faulty or

improperly maintained equipment can

cause injury or death. Therefore:

1. Always have qualified personnel perform the installa-

tion, troubleshooting, and maintenance work. Do not

perform any electrical work unless you are qualified to

perform such work.

2. Before performing any maintenance work inside a power

source, disconnect the power source from the incoming

electrical power.

3. Maintain cables, grounding wire, connections, power

cord, and power supply in safe working order. Do not

operate any equipment in faulty condition.

4. Do not abuse any equipment or accessories. Keep

equipment away from heat sources such as furnaces,

wet conditions such as water puddles, oil or grease,

corrosive atmospheres and inclement weather.

5. Keep all safety devices and cabinet covers in position

and in good repair.

6. Use equipment only for its intended purpose. Do not

modify it in any manner.

ADDITIONAL SAFETY INFORMATION -- For

more information on safe practices for elec-

tric arc welding and cutting equipment, ask

your supplier for a copy of "Precautions and

Safe Practices for Arc Welding, Cutting and

Gouging", Form 52-529.

The following publications, which are available from the

American Welding Society, 550 N.W. LeJuene Road, Mi-

ami, FL 33126, are recommended to you:

1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"

2. AWS C5.1 - "Recommended Practices for Plasma Arc

Welding"

3. AWS C5.2 - "Recommended Practices for Plasma Arc

Cutting"

4. AWS C5.3 - "Recommended Practices for Air Carbon

Arc Gouging and Cutting"

5. AWS C5.5 - "Recommended Practices for Gas Tungsten

Arc Welding“

6. AWS C5.6 - "Recommended Practices for Gas Metal Arc

Welding"“

7. AWS SP - "Safe Practices" - Reprint, Welding Hand-

book.

8. ANSI/AWS F4.1, "Recommended Safe Practices for

Welding and Cutting of Containers That Have Held

Hazardous Substances."

MEANING OF SYMBOLS - As used through-

out this manual: Means Attention! Be Alert!

Your safety is involved.

Means immediate hazards which, if

not avoided, will result in immediate,

serious personal injury or loss of life.

Means potential hazards which could

result in personal injury or loss of life.

Means hazards which could result in

minor personal injury.

SP98-10

a. Éloigner suffisamment tous les matériaux combus-

tibles du secteur où l’on exécute des soudures ou des

coupes à l’arc, à moins de les recouvrir complètement

d’une bâche non-inflammable. Ce type de matériaux

comprend notamment le bois, les vêtements, la sciure,

l’essence, le kérosène, les peintures, les solvants, le

gaz naturel, l’acétylène, le propane et autres sub-

stances combustibles semblables.

b. Les étincelles ou les projections de métal incandes-

cent peuvent tomber dans des fissures du plancher ou

dans des ouvertures des murs et y déclencher une

ignition lente cachée. Veiller à protéger ces ouvertures

des étincelles et des projections de métal.

c. N’exécutez pas de soudures, de coupes, d’opérations

de gougeage ou autres travaux à chaud à la surface

de barils, bidons, réservoirs ou autres contenants

usagés, avant de les avoir nettoyés de toute trace de

substance susceptible de produire des vapeurs

inflammables ou toxiques.

d. En vue d’assurer la prévention des incendies, il

convient de disposer d’un matériel d’extinction prêt à

servir immédiatement, tel qu’un tuyau d’arrosage, un

seau à eau, un seau de sable ou un extincteur portatif.

e. Une fois le travail à l’arc terminé, inspectez le secteur

de façon à vous assurer qu’aucune étincelle ou projec-

tion de métal incandescent ne risque de provoquer

ultérieurement un feu.

3. CHOC ÉLECTRIQUE-- Le gougeage à l’arc et à l’arc

au plasma exige l’emploi de tensions à vide

relativement importantes; or, celles-ci risquent de

causer des dommages corporels graves et même

mortels en cas d’utilisation inadéquate. La gravité du

choc électrique reçu dépend du chemin suivi par le

courant à travers le corps humain et de son intensité.

a. Ne laissez jamais de surfaces métalliques sous ten-

sion venir au contact direct de la peau ou de

vêtements humides. Veillez à porter des gants bien

secs.

b. Si vous devez effectuer un travail sur une surface

métallique ou dans un secteur humide, veillez à assu-

rer votre isolation corporelle en portant des gants secs

et des chaussures à semelles de caoutchouc et en

vous tenant sur une planche ou une plate-forme

sèche.

c. Mettez toujours à la terre le poste de soudage/coupage

en le reliant par un câble à une bonne prise de terre.

d. N’utilisez jamais de câbles usés ou endommagés. Ne

surchargez jamais le câble. Utilisez toujours un

équipement correctement entretenu.

e. Mettez l’équipement hors tension lorsqu’il n’est pas en

service. une mise à la masse accidentelle peut en

effet provoquer une surchauffe de l’équipement et un

danger d’incendie. Ne pas enrouler ou passer le câble

autour d’une partie quelconque du corps.

f. Vérifiez si le câble de masse est bien relié à la pièce en

un point aussi proche que possible de la zone de

travail. Le branchement des câbles de masse à

l’ossature du bâtiment ou en un point éloigné de

la zone de travail augmente en effet le risque de

PRÉCAUTIONS DE SÉCURITÉ

AVERTISSEMENT: Ces règles de sécurité ont pour objet

d’ assurer votre protection. Veillez à lire et à observer les

précautions énoncées ci-dessous avant de monter l’

équipement ou de commercer à l’utiliser. Tout défaut

d’observation de ces précautions risque d’entraîner des

blessures graves ou mortelles.

1. PROTECTION INDIVIDUELLE-- Les brûlures de la

peau et des yeux dues au rayonnement de l’arc

électrique ou du métal incandescent, lors du soudage

au plasma ou à l’électrode ou lors du gougeage à

l’arc, peuvent s’avérer plus graves que celles

résultant d’une exposition prolongée au soleil. Aussi

convient-il d’observer les précautions suivantes:

a. Portez un écran facial adéquat muni des plaques

protectrices et des verres filtrants appropriés afin de

vous protéger les yeux, le visage, le cou et les oreilles

des étincelles et du rayonnement de l’arc électrique

lorsque vous effectuez des soudures ou des coupes

ou lorsque vous en observez l’exécution.

AVERTISSEZ les personnes se trouvant à proximité

de façon à ce qu’elles ne regardent pas l’arc et à ce

qu’elles ne s’exposent pas à son rayonnement, ni à

celui du métal incandescent.

b. Portez des gants ignifugés à crispins, une tunique

épaisse à manches longues, des pantalons sans

rebord, des chaussures à embout d’acier et un

casque de soudage ou une calotte de protection, afin

d’éviter d’exposer la peau au rayonnement de l’arc

électrique ou du métal incandescent. ll est également

souhaitable d’utiliser un tablier ininflammable de

façon à se protéger des étincelles et du rayonnement

thermique.

c. Les étincelles ou les projections de métal incandes-

cent risquent de se loger dans des manches

retroussées, des bords relevés de pantalons ou dans

des poches. Aussi convient-il de garder boutonnés le

col et les manches et de porter des vêtements sans

poches à l’avant.

d. Protégez des étincelles et du rayonnement de l’arc

électrique les autres personnes travaillant à proximité

à l’aide d’un écran ininflammable adéquat.

e. Ne jamais omettre de porter des lunettes de sécurité

lorsque vous vous trouvez dans un secteur où l’on

effectue des opérations de soudage ou de coupage à

l’arc. Utilisez des lunettes de sécurité à écrans ou

verres latéraux pour piquer ou meûler le laitier. Les

piquetures incandescentes de laitier peuvent être

projetées à des distances considérables. Les

personnes se trouvant à proximité doivent également

porter des lunettes de protection.

f. Le gougeage à l’arc et le soudage à l’arc au plasma

produisent un niveau de bruit extrêmement élevé (de

100 à 114 dB) et exigent par conséquent l’emploi de

dispositifs appropriés de protection auditive.

2. PRÉVENTION DES INCENDES-- Les projections de

laitier incandescent ou d’étincelles peuvent

provoquer de graves incendies au contact de

matériaux combustibles solides, liquides ou gazeux.

Aussi faut-il observer les précautions suivantes:

9/97

pas sage d’un courant de sortie par des chaînes

delevage des câbles de grue ou divers chemins

électriques.

g. Empêchez l’apparition de toute humidité, notamment

sur vos vêtements, à la surface de l’emplacement de

travail, des câbles, du porte-électrode et du poste de

soudage/coupage. Réparez immédiatement toute

fuite d’eau.

4. VENTILATION-- La respiration prolongée des fumées

résultant des opérations de soudage/coupage, à

l’intérieur, d’un local clos, peut provoquer des mal-

aises et des dommages corporels. Aussi convient-il

d’observer les précautions suivantes:

a. Assurez en permanence une aération adéquate de

l’emplacement de travail en maintenant une ventila-

tion naturelle ou à l’aide de moyens mécaniques.

N’effectuez jamais de travaux de soudage ou de

coupage sur des matériaux de zinc, de plomb, de

beryllium ou de cadmium en l’absence de moyens

mécaniques de ventilation capables d’empêcher

l’inhalation des fumées dégagées par ces matériaux.

b. N’effectuez jamais de travaux de soudage ou de

coupage à proximité de vapeurs d’hydrocarbure

chloré résultant d’opérations voisines de dégraissage

ou de pulvérisation. La chaleur dégagée ou le

rayonnement de l’arc peut déclencher la formation de

phosgène -- gaz particulièrement toxique -- et d’autres

gaz irritants, à partir des vapeurs de solvant.

c. Une irritation momentanée des yeux, du nez ou de la

gorge constatée au cours de l’utilisation de

l’équipement dénote un défaut de ventilation. Arrêtez-

vous de travailler afin de prendre les mesures néces-

saires à l’amélioration de la ventilation. Ne poursuivez

pas l’opération entreprise si le malaise persiste.

d. Certaines commandes comportent des canalisations

où circule de l’hydrogène. L’armoire de commande est

munie d’un ventilateur destiné à empêcher la forma-

tion de poches d’hydrogène, lesquelles présentent un

danger d’explosion; ce ventilateur ne fonctionne que

si l’interrupteur correspondant du panneau avant se

trouve placé en position ON (Marche). Veillez à

manœuvrer cette commande en vérifiant si le

couvercle est bien en place, de façon à assurer

l’efficacité de la ventilation ainsi réalisée. Ne jamais

débrancher le ventilateur.

e. Les fumées produites par l’opération de soudage ou

de coupage peuvent s’avérer toxiques. Aussi est-il

nécessaire de disposer en permanence d’un dispositif

adéquat de ventilation de type aspirant, afin d’élimi-

ner du voisinage de l’opérateur tout dégagement de

fumée visible.

f. Consultez les recommandations particulières en

matière de ventilation indiquées à l’alinéa 6 de la

norme Z49.1 de l’AWS.

5. ENTRETIEN DE L’ÉQUIPEMENT-- Un équipement

entretenu de façon défectueuse ou inadéquate risque

non seulement de réaliser un travail de mauvaise

qualité mais, chose plus grave encore, d’entraîner des

dommages corporels graves, voire mortels en

déclenchant des incendies ou des chocs électriques.

Observez par conséquent les précautions suivantes:

a. Efforcez-vous de toujours confier à un personnel qua-

lifié l’installation, le dépannage et l’entretien du poste

de soudage et de coupage. N’effectuez aucune

réparation électrique sur l’équipement à moins d’être

qua-lifié à cet effet.

b. Ne procédez jamais à une tâche d’entretien

quelconque à l’intérieur du poste de soudage/

coupage, avant d’avoir débranché l’alimentation

électrique.

c. Maintenez en bon état de fonctionnement les câbles,

le câble de masse, les branchements, le cordon

d’alimentation et le poste de soudage/coupage.

N’utilisez jamais le poste ou l’équipement s’il présente

une défectuosité quelconque.

d. Prenez soin du poste de soudage et de coupage et

des équipements accessoires. Gardez-les à l’écart

des sources de charleur, notamment des fours, de

l’humidité, des flaques d’eau maintenez-les à l’abri des

traces d’huile ou de graisse, des atmosphères corro-

sives et des intempéries.

e. Laissez en place tous les dispositifs de sécurité et tous

les panneaux de l’armoire de commande en veillant à

les garder en bon état.

f. Utilisez le poste de soudage/coupage conformément à

son usage prévu et n’effectuez aucune modification.

6. INFORMATIONS COMPLÉMENTAIRES RELATIVES

À LA SÉCURITÉ--

Pour obtenir des informations complémentaires sur les

règles de sécurité à observer pour le montage et

l’utilisation d’équipements de soudage et de coupage

électriques et sur les méthodes de travail

recommandées, demandez un exemplaire du livret N°

52529 “Precautions and Safe Practices for Arc Weld-

ing, Cutting and Gouging” publié par ESAB. Nous

conseillons également de consulter les publications

sui-vantes, tenues à votre disposition par l’American

Welding Society, 550 N.W. LeJuene Road, Miami, FL

32126:

a. “Safety in Welding and Cutting” AWS Z49.1

b. “Recommended Safe Practices for Gas-Shielded Arc

Welding “AWS A6. 1.

c. “Safe Practices for Welding and Cutting Containers

That Have Held Combustibles” AWS-A6.0.

d. “Recommended Safe Practices for Plasma Arc Cut-

ting” AWS-A6. 3.

e. “Recommended Safe Practices for Plasma Arc Weld-

ing” AWS-C5. 1.

f. “Recommended Safe Practices for Air Carbon Arc

Gouging and Cutting” AWS-C5. 3.

g. “Code For Safety in Welding and Cutting”

CSA-Standard W117. 2.

9/97

SECTION 1 DESCRIPTION

1.1 GENERAL

The PCM-750i is a compact, completely self-contained

plasma cutting system. As shipped, the system is fully

assembled and ready to cut after being connected to

input power and a source of compressed air (90-150 psi).

The PCM-750i package uses the heavy-duty PT-27

torch to deliver cutting power for materials up to 1-1/4

inch thick. Refer to the following paragraphs for descrip-

tions of the PCM-750i packages available as well as

performance specifications.

Use only torches designed for use with this Series A

console. Do NOT use or modify the PT-23, PCT-80 or

any other torch for use on this console. The series A

console uses a pneumatic interlock safety system.

The original console used an electrical safety inter-

lock system. Use of torches not designed for use

with this console could create an electrical shock

hazard.

1.2 SCOPE

The purpose of this manual is to provide the operator with

all the information required to install and operate the

PCM-750i plasma arc cutting package. Technical refer-

ence material is also provided to assist in troubleshoot-

ing the cutting package.

1.3 PACKAGES AVAILABLE

Table 1-1 lists PCM-750i packages available through

your ESAB dealer. Package contents are indented un-

der each complete system description.

Table 1-1. PCM-750i Cutting Packages

Description Part Number

PCM-750i, PT-27, 230 V, 75°, 25 ft, 1-phase

PCM-750i (Ser. A) Console w/ Regulator

PT-27 Torch, 75°, 25 ft

PT-27 Spare Parts Kit*

Work Cable, 25 ft

33980

35504

21661

21623*

680560

PCM-750i, PT-27, 460 V, 75°, 25 ft, 3-phase

PCM-750i (Ser. A) Console w/ Regulator

PT-27 Torch, 75°, 25 ft

PT-27 Spare Parts Kit*

Work Cable, 25 ft

33982

35508

21661

21623*

680560

* Refer to Table 1-2 for PT-27 Spare Parts Kit contents.

Table 1-2. PT-27 Spare Parts Kit Contents

Description Part Number Quantity

50 A Nozzle

Electrode

Swirl Baffle

Heat Shield

Standoff Guide

Valve Pin

Fuse, 15 A, 250 V, Fast Acting

33369

33366

33367

21616

21420

21619

951780

SECTION 1 DESCRIPTION

1.4 SPECIFICATIONS

Refer to Tables 1-3, 1-4, and Figures 1-1 and 1-2 for

PCM-750i technical specifications.

Table 1-3. PCM-750i Specifications

*Duty cycle is based on a 10-minute period; therefore, a 40% duty cycle means the machine may operate for 4 minutes with a cool down

period of 6 minutes; a 60% duty cycle means the machine may operate for 6 minutes with a cool down period of 4 minutes; a 100% duty

cycle means the machine may operate continuously.

Rated

Output

40% Duty Cycle* 50 A @ 105 V dc

60% Duty Cycle* 40 A @ 104 V dc

100% Duty Cycle 30 A @ 103 V dc

Output Current Range 10 to 50 Amperes

Open Circuit Voltage 265 V dc

Rated Primary Input

50 Amperes Output

208/230

Volt

45/42 A, 50/60 Hz, 1-Phase

460

Volt

12A, 50/60 Hz, 1- or 3-Phase

Power Factor @ 50 Amperes Output 70%

Efficiency @ 50 Amperes Output 88%

Current Capacity PT-27 80 A DCSP

Air Requirements PT-27 65 psig @ 250 cfh

Dimensions

Length

Height

Width

w/torch storage

19.0 in. (483 mm)

18.0 in. (457 mm)

12.0 in. (305 mm)

9.0 in. (229 mm)

Weight (less torch, work cable, air regulator) 46 lbs (21 kg)

SECTION 1 DESCRIPTION

Table 1-4. PT-27 Torch Specifications

1" (25.4 mm)

3" (76 mm)

(25.4 mm)

7.3" (185 mm)

75°

Figure 1-1. PT-27 Dimensions

Figure 1-2. PT-27 Cutting Performance

Current Capacity (100% duty) 80 A DCSP

Length of Service Llines 25 ft or 50 ft

Weight

25 ft 5.2 lbs (2.3 kg)

50 ft 9.6 lbs (4.4 kg)

SECTION 2 INSTALLATION

2.1 GENERAL

Proper installation can contribute materially to the satis-

factory and trouble-free operation of the PCM-750i cut-

ting package. It is suggested that each step in this

section be studied carefully and followed as closely as

possible.

2.2 EQUIPMENT REQUIRED

A source of clean, dry air that supplies 250 cfh at 65-75

psig is required for the cutting operation. The air supply

should not exceed 150 psig (the maximum inlet pressure

rating of the air filter-regulator supplied with the pack-

age).

2.3 LOCATION

Adequate ventilation is necessary to provide proper

cooling of the PCM-750i and the amount of dirt, dust, and

excessive heat to which the equipment is exposed,

should be minimized. There should be at least one foot

of clearance between the PCM-750i power source and

wall or any other obstruction to allow freedom of air

movement through the power source.

Installing or placing any type of filtering device will restrict

the volume of intake air, thereby subjecting the power

source internal components to overheating. The war-

ranty is void if any type of filter device is used.

2.4 INSPECTION

A. Remove the shipping container and all packing

material and inspect for evidence of concealed

damage which may not have been apparant upon

receipt of the PCM-750i. Notify the carrier of any

defects or damage at once.

B. Check container for any loose parts prior to dispos-

ing of shipping materials.

C. Check air louvers and any other openings to ensure

that any obstruction is removed.

2.5 PRIMARY ELECTRICAL INPUT

CONNECTIONS (FIGURE 2-1)

ELECTRIC SHOCK CAN KILL! Precautionary mea-

sures should be taken to provide maximum protec-

tion against electrical shock. Be sure that all power

is off by opening the line (wall) disconnect switch

and by unplugging the power cord to the unit when

connections are made inside of the power source.

Be sure that the power source is properly configured

for your input power supply. DO NOT connect a

power source configured for 208/230 V to a 460 V

input power supply. Damage to the machine may

occur.

The PCM-750i console operating on 230 V, 1-phase

input power is equipped with a 10-ft, 3-conductor cable

with plug. A mating receptacle (P/N 674540) is supplied

with the 230 V console. A line (wall) disconnect switch

with a 60-ampere fuse or circuit breaker should be

provided at the main power panel. The cable connecting

the disconnect switch to the receptacle should include

three (two power and one ground) No. 8 AWG insulated

conductors.

The PCM-750i console operating on 460 V, 3-phase

input is equipped with a 10-ft, 4-conductor input power

cord with no plug. A line (wall) disconnect switch, with a

30 ampere circuit breaker, should be provided at the

main power panel. The customer may connect the input

power cord directly to the disconnect switch or purchase

a proper plug and receptacle from a local electrical

supplier. The cable connecting the disconnect switch to

the receptacle should include four (three power and one

ground) No. 12 AWG insulated conductors.

NOTE:

To convert the 460 V, 3-phase console to single phase,

tape back the red wire on the input power cable and then

connect the black, white, and green leads to a suitable

460-volt plug.

SECTION 2 INSTALLATION

Figure 2-1. PCM-750i Interconnection Diagram

CUSTOMER PROVIDED

AIR SUPPLY

(150 psig MAX;

90 psig MIN)

NO. 8 CU/AWG 3-CONDUC-

TOR WIRE (230 V, 1-phase)

or No. 12 CU/AWG 4-con-

ductor wire (460 V, 3-phase)

SAFETY

GROUND

WORK CABLE

Allow at least 10 ft (3 m)

between work and console

WORK

AIR FILTER - REGULATOR

(set at 65-75 psig)

HOSE ASSEMBLY

ON/OFF

POWER SWITCH

RECEPTACLE (P/N 674540)

(supplied w/230 V consoles)

COVER

SAFETY

INTERLOCK

COVER

CUSTOMER FUSED LINE

DISCONNECT SWITCH

(60 A fuse for 230 V, 1-phase;

30 A fuse for 460 V, 1-or 3-phase)

SECTION 2 INSTALLATION

Figure 2-2. Ground and Work Cable Connections

DO NOT ATTACH WORK

CABLE TO PIECE BEING CUT

FREE

WORK CABLE

EARTH GROUND

GROUNDED

WORK TABLE

EARTH GROUND

BE SURE WORK IS IN GOOD

CONTACT WITH TABLE.

WORK CABLE

SECTION 3 OPERATION

E. Fault Light. Will glow red under the following

conditions and operations will come to a complete

stop:

1. When duty cycle has been exceeded. The

duty cycles of this unit are 40% at rated output

current of 50 amperes, 60% at rated output

current of 40 amperes, and 100% at rated

output current of 30 amperes. Duty cycle is

based on a 10 minute cycle; therefore, at 40%

duty cycle, the unit can operate up to 4 minutes

and then must be allowed to cool down for the

next 6 minutes; at 60% duty cycle, the unit can

operate up to 6 minutes and then must be

allowed to cool down for the next 4 minutes; at

100% duty cycle, the unit can operate continu-

ously.

2. When input voltage is outside the range of 150

to 270 volts.

3.3 CUTTING WITH THE PT-27

Use the following procedures to cut with the PT-27 torch

(Figure 3-4).

A. Hold the torch approximately 1/8 inch above the

work and tilted at about 15 - 30°. This reduces the

chance of spatter entering the torch. If the PT-27's

standoff tool is being used, set the standoff at 1/

16 inch for materials less than 1/4-inch thick and at

3/16 inch for those over 1/4-inch thick.

B. Depress the torch switch. Air should flow from the

torch and the high frequency should energize.

C. Two seconds after depressing the torch switch,

the pilot arc should start. The main arc should

immediately follow, allowing the cut to begin. (If

using the LOCK-IN mode, torch switch may be

released after establishing the cutting arc.)

D. After starting the cut, the torch should be main-

tained at a 5-15° forward angle (Figure 3-2). This

angle is especially useful in helping to create a

"drop" cut. When not using the standoff guide, the

nozzle should be held approximately 1/8 inch from

the work.

E. When ending a cut, the torch switch should be

released (press and release if using LOCK-IN

mode) and lifted off the workpiece just before the

end of the cut to minimize double-arcing. This is

to prevent the high frequency from reigniting after

cutting arc extinguishes and causing damage to

the nozzle.

3.1 OPERATION

ELECTRIC SHOCK can kill.

• Do NOT operate the unit with the cover removed.

• Do NOT apply power to the unit while holding or

carrying the unit.

• Do NOT touch any torch parts forward of the torch

handle (nozzle, heat shield, electrode, etc.) with

power switch on.

ARC RAYS can burn eyes and skin;

NOISE can damage hearing.

• Wear welding helmet with No. 6 or 7 lens shade.

• Wear eye, ear, and body protection.

Position the PCM-750i at least 10 feet (3 meters) from

the cutting area. Sparks and hot slag from the cut-

ting operation can damage the unit.

3.2 PCM-750i CONTROLS (FIGURE 3-1)

A. Power Switch (located on rear panel). When

placed in ON position, the green pilot light will glow

indicating control circuit is energized and the cool-

ing fan will run.

B. Output Current Control. Adjustable from 10 to

50 amperes to suit cutting conditions.

C. Air Check Switch. When placed in ON position,

air filter-regulator can be adjusted to desired pres-

sure (65-75 psig) before cutting operations. Allow

air to flow for a few minutes. This should remove

any condensation that may have accumulated

during shutdown period. Be sure to place switch

in OFF position before starting cutting operations.

D. Lock-In Switch. When placed in ON position,

permits releasing torch switch button after cutting

arc has been initiated. To extinguish arc at end of

cut, press and release torch switch button again or

pull torch away from work. When placed in OFF

position, torch switch must be held closely by the

operator during the entire cutting operation and

then released at the end of cut.

SECTION 3 OPERATION

NOTE

When replacing the nozzle, always inspect the elec-

trode for wear. If less than 11/16" of electrode shaft is

remaining, replace the electrode. If the electrode is

used beyond this recommended wear limit, damage to

the torch and power source may occur. Nozzle life is

also greatly reduced when using the electrode below

the recommended limit. Refer to Figure 3-3.

POWER

SWITCH

AIR FILTER - REGULATOR

POWER

CORD

AIR CHECK

POWER

LAMP

FAULT

LAMP

WORK CABLE

CONNECTION

SAFETY

INTERLOCK

SWITCH

AIR HOSE

CONNECTION

OUTPUT

CURRENT

CONTROL

LOCK-IN

TORCH GAS HOSE

CONNECTION

TORCH SWITCH

CONNECTION

AIR

SUPPLY

Figure 3-1. PCM-750i Controls

Figure 3-2. Recommended Torch Angle of 5° to 15°

11/16"

New

Acceptable

WRONG

Figure 3-3. Electrode Wear Limit

PILOT ARC

CONNECTION

F. For rapid re-starts, such as grate or heavy mesh

cutting, do not release the torch switch. In the

postflow mode, the arc can be re-started immedi-

ately by depressing the torch switch. This avoids

the 2-second preflow portion of the cutting cycle.

SECTION 3 OPERATION

3.4 COMMON CUTTING PROBLEMS

Listed below are common cutting problems followed by

the probable cause of each. If problems are determined

to be caused by the PCM-750i, refer to the maintenance

section of this manual. If the problem is not corrected

after referring to the maintenance section, contact your

ESAB representative.

A. Insufficient Penetration.

1. Cutting speed too fast.

2. Damaged cutting nozzle.

3. Improper air pressure.

B. Main Arc Extinguishes.

Cutting speed too slow.

C. Dross Formation. (In some materials and thick-

nesses, it may be impossible to get dross-free

cuts.)

1. Cutting speed too fast or too slow.

2. Improper air pressure.

3. Faulty nozzle or electrode.

D. Double Arcing. (Damaged Nozzle Orifice.)

1. Low air pressure.

2. Damaged cutting nozzle.

3. Loose cutting nozzle.

4. Heavy spatter.

E. Uneven Arc.

Damaged cutting nozzle or worn electrode.

F. Unstable Cutting Conditions.

1. Incorrect cutting speed.

2. Loose cable or hose connections.

3. Electrode and/or cutting nozzle in poor condi-

tion.

G. Main Arc Does Not Strike.

Loose connections.

H. Poor Consumable Life.

1. Improper gas pressure.

2. Contaminated air supply.

WHEN THE ARC BREAKS

THROUGH THE WORK, BRING

THE TORCH TO AN UPRIGHT

POSITION AND PROCEED TO

CUT.

TO START A PIERCE, TILT THE

TORCH TO PREVENT MOLTEN MA-

TERIAL FROM COMING BACK

AGAINST AND DAMAGING THE

TORCH.

Figure 3-4. Piercing Technique using the PT-27

SECTION 4 MAINTENANCE

4.1 GENERAL

If this equipment does not operate properly, stop work

immediately and investigate the cause of the malfunc-

tion. Maintenance work must be performed by an

experienced person, and electrical work by a trained

electrician. Do not permit untrained persons to inspect,

clean, or repair this equipment. Use only recommended

replacement parts.

Be sure that the wall disconnect switch or wall

circuit breaker is open before attempting any in-

spection or work inside of the PCM-750i.

4.2 INSPECTION AND CLEANING

Frequent inspection and cleaning of the PCM-750i is

recommended for safety and proper operation. Some

suggestions for inspecting and cleaning are as follows:

A. Check work cable to workpiece connection.

B. Check safety earth ground at workpiece and at

power source chassis.

C. Check heat shield on torch. It should be replaced

if damaged.

D. Check the torch electrode and cutting nozzle for

wear on a daily basis. Remove spatter, resharpen

point, or replace if necessary.

E. Make sure cable and hoses are not damaged or

kinked.

F. Make sure all plugs, fittings, and ground connec-

tions are tight.

G. Remove or replace carrying strap annually, sooner

if weekly check shows wear or damage.

Water or oil occasionally accumulates in compressed

air lines. Be sure to direct the first blast of air away

from the equipment to avoid damage to the PCM-

750i.

H. With all input power disconnected, and wearing

proper eye and face protection, blow out the inside

of the PCM-750i using low-pressure dry com-

pressed air.

I. Occasionally, bleed all water from the filter be-

neath the air filter-regulator.

4.3 PT-27 TORCH CONSUMABLE PARTS

Make sure power switch on PCM-750i is in OFF

position before working on the torch.

The PT-27 torch head contains a gas flow check

valve that acts in conjunction with the flow switch

and circuitry within the power source. This system

prevents the torch from being energized with high

voltage if the torch switch is accidentally closed

when the shield is removed.

To assemble standard consumable parts, refer to Figure

4-1.

A. Place nozzle, swirl baffle, electrode, and valve

pin into the shield.

B. Thread assembly to the torch body and hand

tighten. Always make sure the shield is tight

before cutting.

Figure 4-1. Assembly of PT-27 Torch Front End Parts

SHIELD

NOZZLE

SWIRL BAFFLE

ELECTRODE

VALVE PIN

SECTION 4 MAINTENANCE

4.4 FLOW SWITCH (FIGURE 4-2)

When excessive contamination is found in the air, the

flow switch (FS-4 or FS-5) should be disassembled and

cleaned as follows:

NOTE

It is not necessary to remove the flow switch from

the system for cleaning.

A. Ensure the system is shut down and there is no

trapped air under pressure in the piping.

B. Remove the piston plug.

C. Remove the spring (FS-4 only). Use care when

handling spring to prevent distortion.

D. Remove the piston.

E. Clean all parts with cleaning agent.

NOTE

Ensure cleaning agent does not contain solvents

which can degrade polysulfone.

Reassemble the flow switch in reverse order.

PISTON PLUG

PISTON

SPRING

FLOW SWITCH

Figure 4-2. Disassembly / Assembly of Flow Switch

The valve pin is a crucial member of the system. Its function is to open the gas flow check

valve that is permanently assembled within the torch head. If the pin is not correctly

placed in the electrode, the valve will not open and the system will not function.

VALVE PIN

ELECTRODE

PLACE LARGE END OF PIN INTO

OPENING IN ELECTRODE AS

SHOWN.

DO NOT REVERSE. Inserting the pin

upside down will restrict air flow.

SECTION 5 TROUBLESHOOTING

The cause of control malfunctions can be found by

referring to the sequence of operations and electrical

schematic diagram (Figure 5-1) and checking the vari-

ous components. A volt-ohmmeter will be necessary for

some of these checks.

Voltages in plasma cutting equipment are high

enough to cause serious injury or possibly death. Be

particularly careful around equipment when the cov-

ers are removed.

NOTE

Before checking voltages in the circuit, disconnect the

power from the high frequency generator to avoid dam-

aging your voltmeter.

5.1 TROUBLESHOOTING

ELECTRIC SHOCK CAN KILL! Be sure that all pri-

mary power to the machine has been externally

disconnected. Open the line (wall) disconnect switch

or circuit breaker before attempting inspection or

work inside of the power source.

Check the problem against the symptoms in the follow-

ing troubleshooting guide. The remedy may be quite

simple. If the cause cannot be quickly located, shut off

the input power, open up the unit, and perform a simple

visual inspection of all the components and wiring.

Check for secure terminal connections, loose or burned

wiring or components, bulged or leaking capacitors, or

any other sign of damage or discoloration.

Depress torch switch. After 2 seconds, is there a pilot arc?

Repair/replace

high frequency

unit

Repair power

source

Yes

5.2 TROUBLESHOOTING GUIDE

A. Difficult Starting.

• Change electrode

• Change nozzle

• Check for good, clean connection of work lead to workpiece

• Check air pressure (65-75 psig)

• Check torch power cable for continuity

SECTION 5 TROUBLESHOOTING

B. No Air

Is air hose connected?

Yes No Connect

Is air adjusted to 65 psig?

Yes No Adjust

Does air come on with air check switch?

Yes No • No electrode in torch

• No valve pin in torch

• Replace electrode

Check continuity of torch switch • Replace valve pin

OK No Replace torch switch

Repair power source

SECTION 5 TROUBLESHOOTING

C. Air does not shut off

Is air check switch OFF?

Yes No Turn switch OFF

Does arc start when nozzle contacts work without depressing torch switch?

Yes No

Check for short in torch switch

Does air flow even when PCM-750i power switch is OFF?

Yes No

Replace Repair power

solenoid valve source

La page charge ...

ESAB PCM-750i Manuel utilisateur

Marque: ESAB

Modèle: PCM-750i

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

PCM-750i Plasma Arc Cutting Package

Télécharger le PDF

rapport

dans d''autres langues

English: ESAB PCM-750i User manual

Documents connexes

Autres documents

GYS WELDING PROTECTION COVER (1200°C/2200°F, 1200g/m2 - 1.75m x 1.50m) Fiche technique