Thermador VCIN60GWS Guide d'installation

THERMADOR.COM

Installation

INSTRUCTIONS

Professional Custom Insert Hoods

THERMADOR.COM

Installation

INSTRUCTIONS

Table of Contents (English)................................................................3

Table de Matières (Français)............................................................22

Índice de Materias (Español)............................................................43

Models |

Modèles |

Modelos:

VCIN36GWS

VCIN42GWS

VCIN48GWS

VCIN54GWS

VCIN60GWS

Professional Custom Insert Hoods

Page. 3

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Table of

CONTENTS

Safety ..................................................................................... 4

Important safety instructions .......................................... 4

Advance planning .................................................................. 6

Before you begin ............................................................ 6

General information ....................................................... 7

Installation instructions ........................................................... 8

Installation considerations............................................... 8

Electrical requirements ................................................... 9

Ductwork preparation .................................................... 10

Common ducting configurations..................................... 12

Choosing the correct blower .......................................... 13

Hood transition................................................................ 13

Preparing the ceiling cutout and housing ....................... 14

Custom insert installation with hood trims...................... 14

Blower motor installation ............................................... 16

Electrical wire connection................................................ 18

Make-Up air damper relay switch (optional) ................... 18

Remote control installation (optional) ............................ 19

Installing filters and grease trays..................................... 20

Installer checklist and service ................................................. 21

Installer checklist ............................................................. 21

Before calling service ...................................................... 21

Product data rating plate ............................................... 21

Service, parts, and accessories..................................back page

Safety

DEFINITIONS

9 WARNING

This indicates that death or serious injuries may occur as a

result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may occur as a

result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

Page. 4

Safety

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: Save these instructions for the local electrical

inspector’s use. Please leave these instructions with this

unit for the owner. Show the owner the location of the

circuit breaker or fuse. Mark it for easy reference.

OWNER: Read and save these instructions. Please retain

these instructions for future reference.

WARNING

If the information in this manual is not

followed exactly, a fire or explosion may

result causing property damage,

personal injury or death.

-- DO NOT store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

-- Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

WARNING

Turn off power circuit at service panel and lock out

panel before wiring this appliance. Requirement: 120

VAC, 60 Hz, 15 A or 20 A for some models. Allow the

appliance to cool after the power has been turned off

before servicing the appliance.

WARNING

Automatically operated device

To reduce the risk of injury disconnect from power

supply before servicing.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

• Before servicing or cleaning unit, switch power off

at service panel and lock the service

disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag,

to the service panel. Contact the manufacturer at

the address or telephone number listed on the

back page.

WARNING

DO NOT repair or replace any part of the appliance

unless specifically recommended in the manuals.

Improper installation, service or maintenance can

cause injury or property damage. Refer to this manual

for guidance. All other servicing should be done by a

qualified technician.

WARNING

ELECTRICAL SHOCK HAZARD

• DO NOT remove connections.

• DO NOT use an extension cord.

• Improper grounding can result in a risk of

electric shock.

• Failure to follow these instructions can result

in death, fire, or electrical shock.

Page. 5

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Grounding Instructions

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric

current.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical

connections and grounding must comply with all

applicable codes.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

WARNING

To reduce the risk of fire or electric shock, DO NOT

use this appliance with any solid-state speed control

devices.

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

• UL 507, The Standard for the Safety of Electric Fans

• CSA C22.2 No. 113, Fans and Ventilators

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

CAUTION

Unit is heavy and requires at least two people

or proper equipment to move and install.

Hidden surfaces may have sharp edges. Use

caution when handling the appliance. Failure

to do so may result in property damage or

personal injury.

State of California Proposition 65 Warning:

: WARNING

This product can expose you to chemicals including

vinyl chloride, which is known to the State of California

to cause cancer and birth defects or other

reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Never modify or alter the construction of the appliance.

For example, do not remove panels, wire covers or

brackets/screws.

CAUTION

For general ventilating use only. DO NOT use to

exhaust hazardous or explosive materials and vapors.

To reduce the risk of fire, use only metal ductwork.

Use a qualified installer.

Remove all tape and packaging before using the

appliance. Dispose of packaging in an environmentally-

responsible manner. Never allow children to play with

packaging material.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Installation work and electrical wiring must be

done by qualified person(s) in accordance with all

applicable codes and standards, including fire-

rated construction.

• Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer's

guideline and safety standards such as those

published by the National Fire Protection

Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code

authorities.

• When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden

utilities.

• Ducted fans must always be vented to the

outdoors.

• USE ONLY METAL DUCTWORK.

• DO NOT vent exhaust air in spaces with walls or

ceilings or into attics, crawl spaces or garages.

CAUTION

An outside fan is to be mounted behind louvers or in a

location where the entrance of drawn in water is

unlikely.

Page. 6

Advance planning

Before you begin

9 CAUTION

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being

turned ON accidentally.

Parts included

• Metal transition with backdraft damper

• Stainless steel baffle filters

• Stainless steel grease trays

• Stainless steel filter spacers

• Side trims

• Blower adapter

• Fastener assortment*

* Hardware provided is for mounting through standard

thickness drywall or plaster into wood studs. Installers are

responsible to provide hardware for other types of

mounting situations.

Tools and parts needed

• Blower (refer to the Ventilation Planning Guide for

compatible blowers)

• Ducting as needed (refer to Equivalent Duct Lengths

for Commonly Used Transitions table)

• Aluminum tape (DO NOT use duct tape.)

• 1/2'' (13 mm) conduit if required (follow local codes)

• 1'' (25.4 mm) Strain relief

• Phillips screwdriver

• T-20 Torx head screwdriver

• 11/32'' nut driver or socket and ratchet

• Drill with 3/16'' (4.76 mm) drill bit

• Framing material (as necessary for framework)

• Circular saw or jigsaw

• Wire stripper

• Tape measure

• Protective work gloves

IMPORTANT: DO NOT throw away any packaging until

appliance is fully installed.

Optional accessories available for

separate purchase

Refer to www.thermador.com for more details.

• REMCPW – Built-in Remote Control Accessory

• EXTNCB25W – 25 ft. Remote and In-line Blower

Extension Cable

• WC8 - 8" Wall Cap

• WC10 - 10" Wall Cap

• RFPLT600P - Roof plate for use with 600 CFM Remote

Blower VTR630

• RFPLT1000P - For use with 1000 CFM Remote Blower

VTR1030 and 1300 CFM Blower VTR1330

Page. 7

General information

Overall dimensions

This model series features brushed stainless-steel filters,

LED lights, and side trims.

NOTE: Transition is centered horizontally. For optimal

performance, the hood should be mounted flush against

the back wall. In such installations, the rear trim piece is

not necessary. For installations of ½'' – 3'' (13 – 76 mm)

from the back wall, the rear trim piece can be used.

IMPORTANT: The hood needs to be centered over the

cooking surface for best performance.

Model Dimension A Dimension B Dimension C

VCIN36WS 32-3/8'' (822) 33-3/4'' (857) With rear trim piece: 7-3/8'' – 10-3/8'' (187 – 264)

VCIN42WS 38-3/8'' (974) 39-3/4'' (1,010) Without rear trim piece: 6-5/8'' – 9-5/8'' (168 – 245)

VCIN48WS 44-3/8'' (1,127) 45-3/4'' (1,162)

VCIN54WS 50-3/8'' (1,280) 51-3/4'' (1,315)

VCIN60WS 56-3/8'' (1,430) 57-3/4'' (1,467)

C

A

B

16

(424)

16

(424)

16

(424)

11/

16

"

6¼" (157)

7

(195)

11/

16

"

20

(554)

20

(554)

20

(554)

22"

(559)

22"

(559)

22"

(559)

12

(326)

12

(326)

12

(326)

11/

16

"

7

(189)

7

(189)

7

(189)

7/

16

"

dia. 10"

(254)

5/

8

"

inches (mm)

Page. 8

Installation instructions

Installation considerations

Clearances and requirements

The custom insert unit is designed for installation inside a

custom-built hood assembly. It is for ducting to the

outside. It cannot be used in conjunction with a

recirculation unit.

Hood installation height above a cooktop, rangetop or

range can vary. To obtain the necessary installation height

above a cooktop, rangetop or range, consult the

appliance's installation manual.

NOTICE: The hood could incur some damage from heat if

a Thermador Professional

®

series range or rangetop is

operated with multiple burners at high settings under a

hood that is installed at minimum clearances while the

hood is turned off.

Hood width

The hood width should be no less than the width of the

cooking surface. For proper performance, the housing

must cover the entire cooking surface.

For proper performance, the hood must be centered

horizontally above the cooking surface. Where space is

not restricted, a wider hood can be used to increase

capture area.

Distance from cooking surface

The installation height ranges from a minimum height of

30'' (762 mm) to a suggested maximum height of 40''

(1,016 mm); however, it is necessary to follow the cooking

appliance manufacturer’s installation instructions for

proper hood height.

Unit weight

This vent hood is heavy. Adequate structure and support

must be provided in all types of installations. When

calculating the load for the housing support system, be

sure to consider the weight of the ventilation unit.

* Follow cooking appliance manufacturer’s

recommendations.

* 30" (762) –

40" (1,016)

Electrical

Zone

7

(189)

7

(189)

7

(189)

7/7/7/

161616""

12

(326)

12

(326)

12

(326)

11/

16

"

inches (millimeters)

Description Weight

VCIN36WS 53 lb (24 kg)

VCIN42WS 63 lb (29 kg)

VCIN48WS 69 lb (31 kg)

VCIN54WS 79 lb (36 kg)

VCIN60WS 85 lb (39 kg)

Integral Blower VTN1090R 23 lb (11 kg)

Integral Blower VTN630W 11 lb (5 kg)

NOTICE:

The supplied weights address only the ventilation unit or

blower. Installer must account for weight of any materials

of construction when calculating the total dead weight

load of installation, including but not limited to: wall, tile,

mortar, plaster, brick, finishes, partitions, and other

similarly incorporated architectural and structural items.

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Page. 9

Blower motors

Integral, In-line and Remote blowers are available through

your authorized Thermador

®

dealer. For local dealer

information, visit the Find a Dealer section of our website

at www.thermador.com.

The blower performance options will vary in cubic feet per

minute (CFM) and is dictated by the cooking surface, the

volume of air that needs to be moved and the length of

the duct run. Refer to the “Blower Motor Installation”

section for detailed blower motor information.

Support structure

Due to the weight of the hood, make sure the hood is

attached to all available wall studs.

Framing must be fastened together and to ceiling joists to

provide enough structural strength to support the weight

of the hood and internal blower, if applicable.

Wall framing should be, at minimum, made of 2"x 4"

lumber. Proper structural support is required to

accommodate the weight of the hood.

Electrical requirements

The unit requires a 120V AC, 60Hz. 15A branch circuit. The

VTR1330 blower in conjunction with a PHxxGWS requires

a 20 amp circuit breaker. The hood should only be

connected to a dedicated circuit (with ground) that has

been installed according to relevant regulations.

When connected to a GFCI-protected supply, Thermador

Professional

®

hoods are suitable for use in damp locations

that are protected from outside weather conditions and

not subject to saturation with water and other liquids, but

can be subject to moderate degrees of moisture (such as

an outdoor covered patio or lanai area). Refer to local

codes, NEC/CEC, and or the Authority Having Jurisdiction

(AHJ) for additional information.

Check your local building codes for proper method of

installation. In the U.S., this unit should be installed in

accordance with applicable local codes or, in the absence

of local codes, with the National Electrical Code, NFPA 70

or the Canadian Electric Code, CSA C22.1-02.

9 WARNING

The appliance must be grounded.

NOTE: The 25 ft. Remote and In-line Blower Extension

Cable accessory (EXTNCB25W) will only work for

distances up to 25 ft. The accessory cable must be

purchased separately. DO NOT use more than one Blower

Extension Cable per installation.

Electrical data

Data, including the model and serial number, is located on

the product data rating label inside the appliance, visible

after removal of the filter frame (see “Product Data Rating

Label”).

Page. 10

Ductwork preparation

Discharge direction

The exhaust air is discharged upwards through a duct or

directly through the outside wall into the open.

Ducting recommendations

Proper performance is dependent upon proper ducting.

Local building codes may require the use of make-up air

systems when using ducted ventilation systems greater

than specified cubic feet per minute (CFM) of air

movement. The specified CFM varies from locale to

locale. It is the responsibility of the owner and the installer

to determine if additional requirements and/or standards

apply to specific installations.

DO NOT USE FLEXIBLE DUCT; it creates back pressure/

air turbulence and reduces performance. Always install a

metal vent cover where the ductwork exits the house.

Hood must be vented to the outside of building only.

COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air

flow and a nonmetallic thermal break to minimize

conduction of outside temperatures as part of the

ductwork. The damper should be on the cold air side of

the thermal break. The break should be as close as

possible to where the ducting enters the heated portion

of the house.

MAKE-UP AIR: Local building codes may require the use

of make-up air systems when using ducted ventilation

systems greater than specified CFM of air movement. The

specified CFM varies from locale to locale. It is the

responsibility of the owner and the installer to determine if

additional requirements and/or standards apply to specific

installations.

To reduce risk of fire and to properly exhaust air, be sure

to duct air outside. Do not vent exhaust air in spaces with

walls or ceilings or into attics, crawl spaces or garages.

The unit cannot be used in conjunction with a recirculation

unit.

Thermador recommends not exceeding 50 ft

(15.24 m) equivalent of duct.

Keep duct runs as short and straight as possible. Elbows

and transitions fittings reduce air flow efficiency. Back to

back elbows and “S” turns give very poor delivery and are

not recommended.

A short, straight length of duct at the inlet of a remote

blower gives the best delivery.

Hoods are supplied with a 10" (254 mm) transition. A

locally supplied transition is required for other sizes.

Use the “Equivalent Duct Lengths for Commonly Used

Transitions” table to compute permissible lengths for duct

runs to outdoors.

Page. 11

Equivalent Duct Lengths for Commonly

Used Transitions

Size (in)

Equivalent

Length (ft)

Size (in)

Equivalent

Length (ft)

61.2

610

8 0.7

10 0.6

3¼" x 10", straight N/A 1

3¼" x 10", Center

reverse elbow , right

N/A 25

3¼" x 14", straight N/A 0.7

3¼" x 10", Left

reverse elbow

N/A 15

3¼" x 10", Right

reverse elbow

N/A 25

612

62

8 6

8 2

10

10 2

65

62

2

5

8 3

8 2

2

10

3¼" x 10",

90° elbow , round

N/A 5

2’ long, 3¼" x 10" fl

ex N/A 20

3¼" x 10",

45° elbow , round

N/A 15

3¼" x 10", Flat elbow N/A 20

61

8 10

8 2

3¼" x 10", Roof jack

and shutter

N/A

65

610

NOTE: These commonly used installation parts can be purchased at a

local hardware store. Thermador does not manufacture all these parts.

Round wall cap

Round roof cap

3¼" x 10" to round

90° elbow ,

Duct Pie ce

3¼" x 10" Center

reverse elbow , left

15N/A

Round to 3¼" x 10"

3¼" x 10" to round

Round to 3¼" x 10"

90° elbow ,

Duct Pie ce

Smooth, straight

90° elbow , round

45° elbow , round

Page. 12

Common ducting

configurations

NOTE: The figure does not represent all configurations or

installation methods. The image is to be used as a guide

ONLY.

Back-draft

damper on

transition

Back-draft

damper on

transition

Back-draft

damper on

transition

Integral BlowerIntegral BlowerIntegral Blower

In-line BlowerIn-line BlowerIn-line Blower

Remote

Blower

Remote Blower

30" (762) –

40" (1,016)

Varies

12

(326)

12

(326)

12

(326)

11/

16

"

inches (mm)

Page. 13

Choosing the correct blower

It is recommended to use only Thermador blowers with

Thermador ventilation hoods. See the

Ventilation Planning

Guide for recommended blowers. Contact Customer

Service for additional options (see the back page for

contact information).

IMPORTANT: Cutting off a connector to the appliance,

blower, or to the extension cable kit will void the warranty.

Blower selection will vary based on the volume of air that

needs to be moved and the length and location of the

duct run. For long duct runs with multiple turns and

bends, consider using a more powerful blower. For the

most efficient air flow exhaust, use a straight run or as few

elbows as possible.

Integral blowers

These blowers are integrated into the hood at the time of

installation.

Remote blowers

Depending on preference and ducting situation, these

blowers can be mounted on the roof or exterior wall of the

home. An exterior installation may be more appealing to

reduce noise in the kitchen.

In-line blowers

To minimize noise in the kitchen, these blowers are

mounted along the duct line anywhere between the

kitchen and the exterior wall. If there is easy access to duct

line (in an attic, for example), this may be an appealing

option.

25 ft. remote and in-line blower extension

cable

The 25 ft. Remote and In-line Blower Extension Cable

(EXTNCB25W) is available to connect the hood to the In-

line and Remote Blowers for distances up to 25 ft.

Accessory cable must be purchased separately. DO NOT

use more than one Blower Connector Cable per

installation.

Hood transition

Discharge direction

The exhaust air is discharged upwards through a duct or

directly through the outside wall into the open.

The hood can be mounted on the wall only with a vertical

discharge.

Assembly of the transition

Hoods are supplied with a 10" (254 mm) round transition.

A locally supplied transition is required for other sizes.

1. A minimum height clearance of 7-7/16'' (189 mm) is

needed above the hood for transition mounting.

2. Align mounting holes at base of transition over the

mounting holes of the 1/2'' (13 mm) flange located at

the top of the hood.

3. Fasten transition to hood using four (4) 1/4'' (6 mm)

sheet metal screws included with hood.

Note: Screws must not hinder damper operation.

4. Seal connection between transition and hood with

aluminum tape. DO NOT use duct tape. Ensure that

the connection is completely sealed.

5. Remove tape holding damper closed.

20 ¼"20 ¼"20 ¼"

(514)(514)(514)

7

(189)

7

(189)

7

(189)

161616

""

12

(322)

12

(322)

12

(322)

11/

16

"

7/7/7/

inches (millimeters)

Page. 14

Preparing the ceiling cutout

and housing

The unit must be mounted to the surrounding housing.

See “Installation considerations” on page 8 for

suggestions on determining hood height.

When calculating the load for the housing support system,

be sure to include the weight of the ventilation unit. See

“Unit weight” on page 8 for unit weight.

Build housing in accordance with the dimensions noted in

“Ceiling Cutout and Supporting Stud Housing

Dimensions”.

For optimal performance, the hood should be mounted

flush against the back wall. In such installations, the rear

trim piece may not be necessary.

For installations of ½'' – 3'' (13 – 76 mm) from the back

wall, the rear trim piece can be used.

Ceiling Cutout and Supporting Stud

Housing Dimensions

Custom insert installation with

hood trims

9 CAUTION

The hood requires at least two people to lift it

safely.

Hidden surfaces may have sharp edges. Use

caution when handling the appliance. Failure

to do so may result in property damage or

personal injury.

9 WARNING

To avoid electrical shock hazard, before installing,

switch power off at the service panel and lock the

panel to prevent the power from being switched on

accidentally.

1. Turn power OFF at the service panel. Lock service

panel to prevent power from being turned ON.

2. Prepare the ductwork.

a) Refer to “Ductwork preparation” on page 10.

b) Install metal transition with backdraft damper so

that the flap opens up toward the ceiling. If

necessary, install thermal break and additional

backdraft damper (refer to “Hood transition” on

page 13).

3. Build the housing framework.

a) Refer to “General information” on page 7 for the

model dimensions.

b) Refer to “Clearances and requirements” on

page 8 for clearance specifications.

c) Build housing framework for applicable model

according to dimensions in “Preparing the ceiling

cutout and housing” beginning on page 14.

⅝'' (16)⅝'' (16)⅝'' (16)

1½'' x 3½'' x 27-13/16''

(38 x 89 x 707)

1½'' x 3½'' x 27-13/16''

(38 x 89 x 707)

1½'' x 3½'' x 27-13/16''

(38 x 89 x 707)

56¼"

(1,429)

56¼"

(1,429)

56¼"

(1,429)

(448)(448)(448)

171717

55

//88""

16" (407)16" (407)16" (407)

0-3''

(0-76)

0-3''

(0-76)

0-3''

(0-76)

1½'' x 3½'' x 23⅜''

(38 x 89 x 594)

1½'' x 3½'' x 23⅜''

(38 x 89 x 594)

1½'' x 3½'' x 23⅜''

(38 x 89 x 594)

12

(322)

12

(322)

12

(322)

11/11/11/

161616

"

inches (mm)

Page. 15

4. Install the hood trim.

a) Hold trim flush to the bottom of the housing.

Secure the trim to the hood with (20) x 3/8''

(9.5 mm) screws.

b) The back trim piece may not be necessary in some

installation scenarios where there is a ½''

(12.7 mm) or less space between the hood and

the back wall.

5. Prepare for the wire routing.

a) Remove the junction box cover.

b) Remove one circular knockout.

c) Install strain relief (not included) into one of the

circular knockouts.

6. Install the unit.

a) Install the custom insert inside the custom

housing.

b) Secure to the rear of the housing framework using

six (6) x 1'' (25.4 mm) mounting screws, as

indicated below.

c) Secure to the top of the housing framework using

eight (8) x 1'' (25.4 mm) mounting screws, 4 per

side.

7. Connect to the ductwork.

8. Install the blower motor.

a) Refer to “Choosing the correct blower” on

page 13.

b) Refer to “Blower motor installation” beginning on

page 16.

9. Connect the electrical wiring.

a) Connect wiring for applicable blower motor (see

blower instructions beginning on page 16).

10. Install hood filters and grease trays.

a) Refer to “Installing grease trays and filters” on

page 20.

11. Test the installation.

a) Test the operation of the blower and the lights.

b) Be sure to check for back-draft. With the blower

on high, close the windows and doors to the area

to ensure that fan does not cause back drafting in

any outlet vent for another appliance.

A

B

Page. 16

Blower motor installation

Blower and Circuit Breaker Ratings

9 CAUTION

To reduce the risk of fire and electric shock, install this

range hood only with the blowers listed in the

Ventilation Planning Guide.

NOTE: Cutting the plug of the blower will void the

warranty or eligibility for return or exchange.

All blower models are sold separately. Use only

Thermador blowers with these ventilation hoods. See the

Ventilation Planning Guide for recommended blowers.

Contact Customer Service for additional options.

All hood models are rated for 120V AC installed with a

blower listed in the table above, using a 15 amp

dedicated circuit breaker. The VTR1330 blower in

conjunction with a PHxxGWS requires a 20 amp circuit

breaker.

Blower selection will vary based on the volume of air that

needs moved and the length and location of the duct run.

For long duct runs with multiple turns and bends, consider

using a more powerful blower. For the most efficient air

flow exhaust, use a straight run or as few elbows as

possible (refer to “Ductwork Preparation”).

Integral blower installation

Integral blower models are integrated into the hood at the

time of installation. Integral blowers should be installed

after the hood is mounted to the wall.

For complete installation instructions see the instructions

supplied with the blower unit.

1. The blower is attached to the hood using weld studs

on the mounting plate. Guide the motor mounting

plate over the studs.

2. Attach four (4) nuts (included with hood) to the weld

studs. Tighten nuts with a 11/32'' nut driver to secure

the blower to the hood.

Blower SKU Voltage Current

Breaker

Amp

Remote VTR630 120 4.2 15

Remote VTR1030 120 5.7 15

Remote VTR1330 120 8.5 15 / 20

In-line VTI610 120 4.2 15

In-line VTI1010 120 5.7 15

Integral VTN630 120 4.2 15

Integral VTN1090 120 5.4 15

10⅞"

(275)

13⅛"

(335)

8¼"

(208)

8¼"

(208)

8¼"

(208)

18⅞"

(473)

inches (mm)

Page. 17

3. Prepare for the wire routing.

• Remove the junction box cover (A).

• Remove one circular knockout (B).

4. Connect the blower’s plug connector to the connector

present inside the hood.

5. Route the blower harness through the self-locking

clip.

Installing a remote blower or an in-line

blower

For complete installation instructions see the instructions

supplied with the blower unit.

Remote blower

Depending on preference and ducting situation, these

blowers can be mounted on the roof or exterior wall of the

home. An exterior installation may be more appealing to

reduce noise in the kitchen.

In-line blower

To minimize noise in the kitchen, these blowers are

mounted along the duct line anywhere between the

kitchen and the exterior wall. If there is easy access to duct

line (in an attic, for example), this may be an appealing

option.

Blower wire connection

1. Remove junction box channel covering the wires.

2. Remove one circular knockout.

3. Route the blower motor’s plug connector to the hood.

Connect the blower’s harness to the hood harness.

A

B

19"

(485)

2⅛"

(54)

10"

(254)

1¾"

(45)

20¾"

(527)

12⅞"

(327)

12⅛"

(308)

6½"

(165)

1⅞"

(48)

13⅝"

(346)

dia.

9⅞"

(251)

inches (mm)

12⅛"

(308)

14⅜"

(365)

⅞" (22)

1¾"

(44)

19⅛"

(486)

ø 9⅞"

(251)

12"

(305)

12⅞"

(327)

inches (mm)

Page. 18

Electrical wire connection

1. Run a 120V AC, 15A circuit power cable or 20A for a

PHxxGWS product and the VTR1330 blower from the

service panel through one of the holes in the top

plate.

2. Connect black wire to power supply black wire, white

wire to power supply white wire and green wire to

green wire or bare wire.

3. Place all wiring connections inside the junction box

channel. Reinstall on the top plate. Ensure that the

wires are secure and that no wires are pinched.

EXTNCB25W 25 ft. remote and in-line

blower extension cable (optional)

Parts Included

• 1 – 25ft cable

• 2 – Adapter Cables (NOT NEEDED for all models)

Blower extension cable connection

The internal blower harness should be routed through the

knockout and secured with a 1'' (25.4 mm) strain relief.

The remote harness can then be connected to the blower

harness outside the unit.

NOTE: Cutting of the connector will void the warranty of

the appliance.

The blower extension cable is compatible with the

following In-line & Remote blowers:

Make-up air damper relay

switch (optional)

Local codes may require the use of an additional backdraft

and/or make-up air damper. Contact your local HVAC

professional for specific requirements.

This hood provides a relay switch to connect a Make-Up

Air Damper (120V max). Installations will vary according to

the location in the home where the unit is installed and the

damper used. Use the following illustration as guidance

for your installation. Always comply with local code

requirements.

1. Access the hood’s wiring.

2. Route the Make-up Air Damper harness through the

strain relief to the terminal block.

• The Make-up air kit hot and return connections

can use either terminal connection. There is no

polarity requirement for the two pin terminal

block.

3. Secure the ground wire with the green T-20 ground

screw.

White to white

Black to black

Green to green

or bare wire

Blower SKU

Remote Blower VTR630

Remote Blower VTR1030

Remote Blower VTR1330

In-line Blower VTI610

In-line Blower VTI1010

Page. 19

Built-in remote control

accessory (optional)

Before you begin, read these instructions carefully. It is

recommended that the Remote Control be wired to the

hood after the hood is installed.

REMCPW Parts Included

• 1 – Remote control

• 1 – 30 ft. extension harness

IMPORTANT: Cutting off a connector to the appliance or

to the extension cable kit will void the warranty.

Remote control installation

1. Prepare the wall (or similar surface) cutout for

installation as shown below

(view is shown facing wall).

2. Access the hood’s wiring. Route the 30 ft. extension

harness through the strain relief to the square

mounting clip until it clicks.

3. Route the 30 ft extension harness through the cutout

and connect the harness to the back of the remote

control bracket.

4. Press the bracket inside the cutout. Drill a ¼'' (6 mm)

tap hole through the bracket holes into the wall.

Mount the bracket to the wall using the four (4) screws

provided.

5. Hook up the wire harness connector inside the bracket

to the terminal on the back side of the remote control.

Use either terminal.

6. Snap the Remote Control into the bracket.

13

5

8

/

"

(346)

2

5

8

/

"

(65)

inches (mm)

Page. 20

Installing grease trays and

filters

Install filters and grease trays

NOTE: DO NOT use burners, elements, or oven while

hood is disassembled.

1. Turn the fan and lights off.

2. Remove all plastic from hood pieces.

3. Insert in the following order:

a) Grease tray — Insert in rear tray. Grease trays

must be in place before installing the filters. Push

the grease tray in and down inside the grease tray

trough.

-- The small grease tray must be installed in the

center of hood

.

b) Filters — start with inserting the filter in the

middle and work out to the ends. Slide the filter

up, toward the front of the hood, then push down

on top of the grease tray

.

-- The 8" filter must be installed in the center of

hood at all times.

c) Filter spacers — If applicable, insert the filter

spacers on the left and right ends. Push up, slide

toward the front of the hood, then push in at the

bottom.

Reverse the above directions to remove the grease trays

and filters. Ensure filters are cool and grease has

congealed before removal.

(1) LED lights (2) Touch control panel

(3) Baffle filters (4) Grease trays

(5) Grease tray trough (6) Filter spacers

2

3

4

5

6

1

2

3

1

La page charge ...

Thermador VCIN60GWS Guide d'installation

Ce manuel convient également à

Thermador VCIN60GWS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents