Simplicity MANUALS, OPERATOR'S Manuel utilisateur
- Catégorie
- Accessoires pour véhicules automobiles
- Taper
- Manuel utilisateur
490000
Operator's Manual
Manual del operador
Manuel d'utilisation
© 2024 Briggs & Stratton. All rights reserved. 80131526
Revision A
Not for
Reproduction
9
10
11
12
13
14
15
16
17
18
3
Not for
Reproduction
General Information
This manual contains the safety information about the hazards and risksrelatedto
the engine and how to prevent them.It also containsthe correctoperation and
maintenance of this engine.It is important that you read, understand, and obey these
instructions. Keepthis manual for future reference.
NOTE:The figures and illustrations in this manual are for information only and can be
different from your model. Use the figures thatalign withyour engine configuration. If it is
necessary, speak to an Authorized Service Dealer.
Record the date of purchase, engine model, type, trim, and the engine serial number
for replacement parts. These numbers are on your engine. Refer to the Features and
Controls section.
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
European Office Contact Information
For questions related to European emissions, contact our European office at:
Max-Born-Straße 2, 68519 Viernheim, Germany.
European Union (EU) Stage V (5): Carbon
Dioxide (CO2) Values
Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values
of Briggs & Stratton EU Type-Approval Certificate engines.
Recycling Information
Recycle all cartons, boxes, used oil, and batteries as
specified by government regulations.
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol identifies safety information about hazards that could
result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to
indicate the likelihood and the potential severity of injury. In addition, a hazard symbol
is used to represent the type of hazard.
DANGER indicates a hazard which, if not avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could result in death or serious
injury.
CAUTION indicates a hazard which, if not avoided, could result in minor or moderate
injury.
NOTICE indicates information considered important but not hazard-related.
Hazard Symbols and Meanings
Safety information about
hazards that can result in
personal injury.
Read and understand the
Operator's Manual before
operating or servicing the
unit.
Fire Hazard Explosion Hazard
Shock Hazard Toxic Fume Hazard
Hot Surface Hazard Kickback Hazard
Amputation Hazard -
Moving Parts
Fuel Level - Maximum
Do Not Overfill
Safety Messages
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which is
known to the State of California to cause cancer, and carbon monoxide, which is known
to the State of California to cause birth defects or other reproductive harm. For more
information go towww.P65Warnings.ca.gov.
WARNING
Briggs & Stratton® Engines are not designed for and are not to be used to power:
fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);
motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not
sanctioned by Briggs & Stratton. For information about competitive racing products, see
www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs
& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result
in serious injury or death.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you add fuel
• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)
minutes to make sure that the engine is cool.
• Fill the fuel tank outdoors or in an area that has good airflow.
• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above
the bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
• If fuel spills, wait until it dries before you start the engine.
When you start the engine
• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are
correctly installed.
• Do not crank the engine with the spark plug removed.
• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
• If there is natural or LP gas leakage in the area, do not start the engine.
• Because vapors are flammable, do not use pressurized starter fluids.
When you operate the equipment
• Do not tilt the engine or the equipment at an angle which causes fuel to spill.
• Do not choke the carburetor (if equipped) to stop the engine.
• Do not start or operate the engine with the air cleaner (if equipped) or the air
filter (if equipped) removed.
When you do maintenance
• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occurand could result a fire or an explosion.
• During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,
if mounted on the engine, is empty and that the spark plug side is up. If the fuel
tank is not empty, leakage can occurand could result a fire or an explosion.
• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
• Do not change the governor spring, links or other parts to increase engine
speed.
• Do not hit the flywheel with a hammer or hard object. This could result in failure
of the flywheel during operation.
• Replacement parts must be of the same design and installed in the same
position as the original parts. Other parts could result in damage or an injury.
When you move the location of equipment
• Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the
CLOSED position.
5
Not for
Reproduction
When fuel or equipment is in storage with fuel in the fuel tank
• Because pilot lights or other ignition sources can cause explosions, keep fuel or
equipment away from furnaces, stoves, water heaters or other appliances that
have pilot lights.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Engine start-up causes spark that could result in a fire or explosion.
• If there is natural or LP gas leakage in the area, do not start the engine.
• Because vapors are flammable, do not use pressurized starter fluids.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See
a doctor. You may have carbon monoxide poisoning.
• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
• DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and windows
for ventilation. After the operation of this product, carbon monoxide can quickly
collect in these spaces and stay for hours.
• ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go.Broken bones, fractures, bruises or sprains
could result.
• To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
• Before you start the engine, disconnect or remove all external equipment and
engine loads.
• Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
WARNING
Rotating parts can entangle hands, feet, hair, clothing, or accessories and result
in traumatic amputation or laceration.
• Operate equipment with the guards correctly installed.
• Keep hands and feet away from rotating parts.
• Remove jewelry and make sure that long hair is away from all rotating parts.
• Do not wear loose clothes or items that could become caught.
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
• Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
• Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
WARNING
Accidental engine spark can cause an electric shock, fire or explosion and could
result in entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
• Disconnect all spark plug wires and keep them away from the spark plugs.
• Disconnect the battery wire from the negative battery terminal (only engines with
electric start).
• Use only the correct tools.
When you check for spark:
• Use an approved spark plug tester.
• Do not check for spark with the spark plug removed.
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
If you smell gas
• Do not start the engine.
• Do not switch on electrical switches.
• Do not use a phone in the vicinity.
• Evacuate the area.
• Contact the gas supplier or the fire department.
Features and Controls
Engine Controls
Compare the callout letters in Figures 1, 2 and 3 to the engine controls in the list that
follows:
A. Engine Identification Numbers Model - Type - Code
B. Spark Plug
C. Air Cleaner
D. Dipstick
E. Oil Drain Plug, if installed
F. Air Intake Grille
G. Oil Filter
H. Electric Starter
I. Carburetor
J. Fuel Filter (if installed)
K. Fuel Pump (if installed)
L. Quick Oil Drain (if installed)
M. Oil Cooler (if installed)
N. Electric Control Unit (if installed)
O. Remote Oil Filter (with Oil Xtend, if installed)
P. Oil Cap Insert(with Oil Xtend, if installed)
Q. Alternate Oil Fill (with Oil Xtend, if installed)
Engine Control Symbols and Meanings
Engine Speed - FAST Engine Speed - SLOW
Engine Speed - STOP ON - OFF
Engine Start
Choke CLOSED
Engine Start
Choke OPEN
6 BRIGGSandSTRATTON.COM
Not for
Reproduction
Fuel Cap
Fuel Shut-off OPEN
Fuel Shut-off CLOSED
Operation
Oil Recommendations
Oil Capacity: Refer to SECTION 9 - SPECIFICATIONS.
We recommend the use of Briggs & Stratton® Warranty Certified oils for best
performance. Other high-quality detergent oils are permitted if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Use the chart to select the best viscosity for the outdoor temperature range expected.
Vanguard® 15W-50 Synthetic oil gives the best protection in most environments as well
as superior protection for equipment operated in hot temperatures. Engines on most
outdoor power equipment can operatewell with Synthetic 5W-30 oil.
A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.
B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Checkthe oil level frequently.
C 5W-30
D Synthetic 5W-30
EVanguard® Synthetic 15W-50
Check the Oil Level
Before you check or add oil
• Make sure the engine is level.
• Clean the oil fill area of debris.
• Refer to the Specifications section for oil capacity.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or
dealers could have added oil to the engine. Before you start the engine for the first time,
make sure that the oil is at the correct level. Add oil as specified by the instructions in
this manual. If you start the engine without oil, damage will occur and the engine will not
be repaired under warranty.
1. Remove the dipstick (A, Figure 4) and clean with a cloth.
2. Install and tighten the dipstick (A, Figure 4).
3. Remove the dipstick and check the oil level. Make sure that the oil level is at the
top of the full indicator (B, Figure 4) on the dipstick.
4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 4). Do not add
too much oil.
5. Wait one minute and check the oil level again. Make sure that the oil level is
correct.
6. Install and tighten the dipstick (A, Figure 4).
Low Oil Protection System (if installed)
A low oil sensor is installed on some engines. If the oil is low, the sensor will show a
warning light or stop the engine. Stop the engine and do the steps that follow before you
start the engine.
• Make sure that the engine is level.
• Do an oil check. Refer to the Check Oil Level section.
• If the oil level is low, add the correct amount of oil. Start the engine and make
sure that the warning light (if installed) does not come on.
• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton
Authorized Service Dealer to correct the oil problem.
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
• Gasoline with up to 10% ethanol (gasohol) is permitted.
NOTICE
Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or
change the engine to operate on alternate fuels. Use of unapproved fuels could result
in damage to engine components, which will not be repaired under the warranty.
To protect the fuel system from gum formation, and corrosion, mix analcohol-free fuel
stabilizer and ethanol treatmentinto the fuel. Refer to the Storage section. All fuel is
not the same. If start or performance problems occur, change fuel providers or brands.
This engine is certified to operate on gasoline. The emissions control system for
carbureted engines is EM (Engine Modifications). The emissions control systems for
engines with electronic fuel injection are ECM (Engine Control Module), MFI (Multiport
Fuel Injection), TBI (Throttle Body Fuel Injection) and if equipped an O2S (Oxygen
Sensor).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 87 octane/87 AKI (91 RON)
gasoline is permitted.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you add fuel
• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)
minutes to make sure that the engine is cool.
• Fill the fuel tank outdoors or in an area that has good airflow.
• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above
the bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
• If fuel spills, wait until it dries before you start the engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure 5) with fuel. Because fuel will expand, do not fill above
the bottom of the fuel tank neck (B).
3. Install the fuel cap.
Start the Engine
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See
a doctor. You may have carbon monoxide poisoning.
• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
• DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and windows
for ventilation. After the operation of this product, carbon monoxide can quickly
collect in these spaces and stay for hours.
• ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
7
Not for
Reproduction
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you start the engine
• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are
correctly installed.
• Do not crank the engine with the spark plug removed.
• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
• If there is natural or LP gas leakage in the area, do not start the engine.
• Because vapors are flammable, do not use pressurized starter fluids.
WARNING
Rotating parts can entangle hands, feet, hair, clothing, or accessories and result
in traumatic amputation or laceration.
• Operate equipment with the guards correctly installed.
• Keep hands and feet away from rotating parts.
• Remove jewelry and make sure that long hair is away from all rotating parts.
• Do not wear loose clothes or items that could become caught.
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go.Broken bones, fractures, bruises or sprains
could result.
• To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
• Before you start the engine, disconnect or remove all external equipment and
engine loads.
• Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
Types of StartSystems
Before you start the engine, you must know the type ofstartsystem on your engine.
Your engine has one of these types of systems.
•Electronic Fuel Injection (EFI) System: An EFI system does not have a
choke or a primer.
•Electronic Fuel Management System: An Electronic Fuel Management
system has an Electronic Control Unit that monitors engine and temperature
conditions. It does not have a manual choke or a primer.
•Choke System: This type of system has a choke to be used in cool
temperatures. Some models have a separate choke control, but some have a
combination choke and throttle choke. This type does not have a primer.
NOTE:Your equipment could have remote controls. Refer to the equipment manual for
the location and operation of remote controls.
Electronic Fuel Injection (EFI) System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure that equipment drive controls, if installed, are disengaged.
3. Move the fuel shut-off (A, Figure 6), if installed, to the OPEN position.
4. Move the throttle control (B, Figure 6), if installed, to the FAST position. Operate the
engine in the FAST position.
NOTE:For models with Electronic Throttle Control, the throttle control can be in any
position when you start the engine.
5. Turn the electric start switch (D, Figure 6) to the ON or START position.
NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).
Wait one minute between start cycles.
If the engine does not start after 3or 4 times, contact your local dealer or goto
BRIGGSandSTRATTON.COM or call 1-800-444-7774 (in USA).
Electronic Fuel Management System
1. Check the engine oil. See Check and Add Oil section.
2. Make sure that equipment drive controls, if installed, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if installed, to the OPEN position.
4. Move the throttle control (B, Figure 7), if installed, to the FAST position. Operate the
engine in the FAST position.
5. Rewind Start, if installed: Turn the key switch (D, Figure 7) to the ON / START
position.
6. Rewind Start, if installed: Tightly hold the starter cord handle (E, Figure 7). Pull
the starter cord handle slowly until resistance is felt, then pull quickly.
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the engine
faster than you can let go. Broken bones, fractures, bruises or sprains could result. To
prevent kickback when you start the engine, pull the starter cord slowly until resistance
is felt and then pull quickly.
7. Turn the key switch (D, Figure 7)to the ON / START position.
NOTICETo extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
NOTE:If the engine does not start after 2-3 attempts, contact your local dealer or go to
BRIGGSandSTRATTON.COM or call 1-800-444-7774 (in USA).
Choke System
1. Check the engine oil. See the Check and Add Oil Level section.
2. Make sure that equipment drive controls, if installed, are disengaged.
3. Move the fuel shut-off (A, Figure 8), if installed, to the OPEN position.
4. Move the throttle control (B, Figure 8), if installed, to the FAST position. Operate the
engine in the FAST position.
5. Move the choke control (C, Figure 8) to the CLOSED position.For models a
combination choke/throttle control (B, C, Figure 8) move the control to the CHOKE
position.
NOTE:The choke is usually not necessary when you start a warm engine.
6. Rewind Start, if installed: Turn the key switch (D, Figure 8), if installed, to the ON/
START position.
7. Rewind Start, if installed: Tightly hold the starter cord handle (E, Figure 8), if
installed. Pull the starter cord handle (E) slowly until resistance is felt, then pull it
quickly.
8. Turn the electric start switch, if installed, to the ON/START position.
NOTICE
To extend the life of the starter, use short start cycles (five seconds maximum). Wait one
minute between start cycles.
9. As the engine warms, move the choke control (C, Figure 8) to the OPEN position.
NOTE:If the engine does not start after 2-3 attempts, contact your local dealer or go to
BRIGGSandSTRATTON.COM or call 1-800-444-7774.
Stop the Engine
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
• Do not choke the carburetor (if equipped) to stop the engine.
1. Disengage equipment controls. See the equipment manual for location and
operation of remote controls.
2. Move the throttle control (B, Figure 9), if installed, to the SLOW position.
3. Turn the key switch (D, Figure 9) to the OFF or STOP position. Remove the key,
and keep it in a safe location out of reach of children
4. With the throttle control in the SLOW position, turn the electric start switch (D,
Figure 9) to the OFF position. Remove the key. Keep it in a safe location out of
reach of children.
5. After the engine stops, move the fuel shut-off (A, Figure 9), if installed, to the
CLOSED position.
8 BRIGGSandSTRATTON.COM
Not for
Reproduction
Maintenance
Maintenance Information
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Duringmaintenanceif it is necessary to tilt the unit, make sure that the fuel tank, if
mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not
empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted
in a different direction, it will not easily start because of oil or fuel contamination of the air
filter or the spark plug.
WARNING
Accidental engine spark can cause an electric shock, fire or explosion and could
result in entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
• Disconnect all spark plug wires and keep them away from the spark plugs.
• Disconnect the battery wire from the negative battery terminal (only engines with
electric start).
• Use only the correct tools.
When you check for spark:
• Use an approved spark plug tester.
• Do not check for spark with the spark plug removed.
WARNING
All the components used to assemble this engine must stay in the initial position
for correct operation. Damage or injury can occur if you use incorrect parts or you
do not replace all parts on the engine.
• Replacement parts must be of the same design and installed in the same
position as initial parts.
• If installed, do not change the governor spring, links, or other parts to increase
the engine speed.
See a Briggs & Stratton Authorized Service Dealer for all maintenance and servicing of
the engine and engine parts.
Maintenance Schedule
Engine Oil Filter Type
Service Action None Black Yellow/Orange Oil Xtend
First 5 hours only
Change the oil. ●
8 hours or Daily1
Check the engine oil level. ● ● ●
Clean the area around the
muffler and controls.
● ● ● ●
25 hours or Annually1
Clean the air filter2.● ● ● ●
Clean the pre-cleaner (if
installed)2.
● ● ● ●
50 hours or Annually1
Service the exhaust system. ● ● ● ●
Change the oil. ● ●
Replace the oil filter (if installed). ●
100 hours or Annually1
Change the oil. ●
Replace the oil filter (if installed). ●
250 hours or Annually1
Replace the spark plug. ● ● ● ●
Replace the air filter. ● ● ● ●
Replace the fuel filter. ● ● ● ●
Change the oil. ●
Replace the oil filter (if installed). ●
Annually
Replace the pre-cleaner (if
installed).
● ● ● ●
Replace the fuel filter. ● ● ● ●
Service the cooling system2.● ● ● ●
Check and set the valve
clearance3.
● ● ● ●
1Use the interval that comes first, hours, or annually.
2Clean more frequently in dusty conditions or when many particles are in the air.
3Not necessary to check the lash if performance problems do not occur.
Emissions Control Service
For maintenance, replacement, or repair of emissions control devices and
systems, contact a qualified off-road engine repair establishment or service
technician. However, for "no charge" emissions control service, the work must be done
by a factory authorized dealer. Refer to the Emissions Control Statements.
Electronic Fuel Injection (EFI) System
The EFI System monitors engine temperature, engine speed, and battery voltage for
engine start-up and warm-up. There are no adjustments on the system. If start-up or
operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.
NOTICEMake sure to obey the steps that follow or damage to the EFI system could
occur.
• DO NOT start the engine if the battery cables are loose.
• Turn the key to the OFF position before you disconnect, remove, and / or install
the battery.
• DO NOT use a battery charger to start the engine.
• DO NOT disconnect the battery cables during engine operation.
• When you disconnect the battery cables, first connect the positive (+) cable, and
then connect the negative (-) cable to the battery.
• When you charge the battery, turn the ignition switch to the OFF position,and
disconnect the negative (-) battery cable from the battery.
• DO NOT spray water directly on the Electronic Control Module.
Electronic Fuel Management System
The Electronic Fuel Management System monitors engine temperature, engine speed,
and battery voltage to adjust the choke during engine start-up and warm-up. There
are no adjustments on the system. If start-up or operation problems occur,speak to
aBriggs & StrattonAuthorized Service Dealer.
NOTICEMake sure that you follow these rules or the Electronic Fuel Management
System could be damaged.
• DO NOT start the engine if the battery cables are loose.
• Before you connect the jump start cables, or disconnect or reconnect the battery
cables, turn the ignition switch to the OFF position. When you charge the
battery, turn the ignition switch to the OFF position.
• When you disconnect the battery cables from the battery, disconnect the
negative (- ) cable, and then disconnect the positive (+) cable to the battery.
When you connect the battery cables to the battery, connect the positive (+)
cable, and then the negative (-) cable to the battery.
• DO NOT use a battery charger to start the engine.
• DO NOT disconnect the battery cables during engine operation.
• DO NOT spray water directly on the Electronic Control Unit.
Carburetor and Engine Speed
Do not make adjustments to the carburetor, governor spring, linkages, or other parts
to adjust the engine speed. If adjustments arenecessary,contact a Briggs & Stratton
Authorized Service Dealer forservicing.
NOTICE
The equipment manufacturer specifies the maximum speed for the engine as installed
on the equipment. Do not exceed this speed. If you are not sure what the equipment
maximum speed is, or what the engine speed is set to from the factory, contact a Briggs
& Stratton Authorized Service Dealer for assistance. For safe and correct operation
of the equipment, the engine speed should only be adjusted by a qualified service
technician.
Servicing the Spark Plug
Check the spark plug gap (A, Figure 10) with a wire gauge (B). If necessary, set the
spark plug gap. Install and tighten the spark plug to the correct torque. For gapand
torque specifications, refer to the Specifications section.
9
Not for
Reproduction
Servicing theExhaust System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
• Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
• Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
Remove debris from the muffler and cylinder area. Inspect the muffler for cracks,
corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and
inspect for damage or carbon blockage. If damage is found, install the replacement parts
before you operate the equipment.
Change Engine Oil
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occur and cause a fire or an explosion.
• Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Used oil is a hazardous waste product and must be discarded of correctly. Do not
discard with household waste. Contact your local authorities, service center, or dealer
for safe disposal or recycling facilities.
Remove Oil
1. With the engine OFF but warm, disconnect the spark plug wire(s) (D, Figure 11),
and keep it away from the spark plugs (E).
2. Remove the dipstick (A, Figure 12).
Oil Drain Plug, if installed
1. Remove the oil drain plug (F, Figure 13). Drain the oil into an approved container.
NOTE:On Oil Xtend,remove the cap and filter (F, Figure 15) to drain the oil from the oil
housing.
NOTE:If the oil drain hole on your engine has a female drain plug (F, Figure 13),you
can replace it with a male drain plug (F).
2. After you drain the oil, install and tighten the oil drain plug (F, Figure 13).
Quick Oil Drain, if installed
1. Disconnect the oil drain hose (H, Figure 14) from the side of the engine.
2. Turn and remove the oil drain cap (I, Figure 14). Carefully lower the quick oil drain
hose (H) into an approved container (J).
NOTE:On Oil Xtend,remove the cap and filter (F, Figure 15) to drain the oil from the oil
housing.
3. After you drain the oil, install the oil drain cap (I, Figure 14). Attach the oil drain
hose (H) to the side of the engine.
Add Oil
• Make sure the engine is level.
• Clean the oil fill area of all debris.
• Refer to the Specifications section for oil capacity.
1. Remove the dipstick (A, Figure 4). Remove oil from the dipstick with a clean cloth.
2. Slowly add oil into the engine oil fill (C, Figure 4). Do not put too much oil in the
engine oil fill. Wait one minute and then check the oil level.
NOTE: Do not add oil at the quick oil drain, if equipped.
3. Install and tighten the dipstick (A, Figure 4).
4. Remove the dipstick and check the oil level. The correct oil level is at the top of the
full indicator (B, Figure 4) on the dipstick.
5. Install and tighten the dipstick (A, Figure 4).
6. Connect the spark plug wire(s)to the spark plug(s). See Remove Oil section.
Change the Oil Filter(Oil Xtend)
1. Drain the oil from the engine. Refer to the Remove Oil section.
2. Use a 3/4" or 19 mm socket wrench to loosen the nut (A, Figure 16) on top of the oil
cap (B).
NOTICEDO NOT hit the wrench with a mallet or other object to loosen the nut on top of
the oil cap. Use a wrench extension if more torqueis necessary to loosen the nut.
3. Turn the oil cap (B, Figure 16) counterclockwisewith your hand and remove the oil
cap (B).
4. Lightly pull the oil filter (D, Figure 17) off the oil cap (B).Discard the oil filter.
5. Pushthe new filter (D, Figure 17) onto the oil cap (B) until you hear a click.
6. Add oil directly into the oil housing (G, Figure 18).
7. Checkthe oil level.Make sure that the oil is at the correct level.
8. With the oil filter (D, Figure 17) correctly attached to the oil cap (B), installthe oil
cap assembly (F, Figure 18) into the oil filter housing (G).
IMPORTANT:Tighten the nut (A, Figure 16)clockwise on the oil cap (B) to 15 lb-ft (20
Nm).
9. Run the engine for 10 seconds.
10. Stop the engine. Check the oil level again. Make sure that the oil level is at the top
of the full indicatoron the dipstick.
NOTICEThe Oil Xtend filter must be in position to increase oil pressure.DO NOT run
the enginewithout the filter installed as permanent engine damagecanoccur.
Change the Oil Filter
1. Drain the oil from the engine. Refer to the Remove Oil section.
2. Remove the oil filter (H, Figure 19) anddiscard correctly.
3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.
4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten
the oil filter 1/2 to 3/4 turns.
5. Add oil. Refer to the Add Oil section.
6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.
7. Stop the engine. Make sure thatoil level is at the top of the full indicatoron the
dipstick. Refer to the Add Oil section.
Servicingthe Air Filter
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
• Do notstart and operate the engine with the air cleaner assembly (if equipped)
or the air filter (if equipped) removed.
NOTICE
Do not use pressurized air or solvents to clean the filter. Pressurized air could result in
damage to the filter and solvents will dissolve the filter.
See the Maintenance Schedule forservicingrequirements.
Different models will use a foam or a paper filter. Some models could also have an
optional pre-cleaner that can becleanedand used again. Compare the illustrations in
this manual with the type installed on your engine and service as follows.
Cyclonic Air Filter with Pre-Cleaner
WARNING
Gaseous vapors are flammable and explosive. Fire or explosion could result in
burns or death.
• Do notstart and operate the engine with the air cleaner assembly (if equipped)
or the air filter (if equipped) removed.
NOTICE
Do not use pressurized air or solvents to clean the filter. Pressurized air could result in
damage to the filter and solvents will dissolve the filter.
10 BRIGGSandSTRATTON.COM
Not for
Reproduction
1. Loosen the fastener(s)(A, Figure 20) and remove the cover (B).
2. Open the latch (C, Figure 20) and remove the filter (D).
3. Remove the pre-cleaner (E, Figure 20), if installed, from the filter (D).
4. To loosen debris, lightly tap the air filter on a hard surface. If the filter is dirty,
replace it with a new filter.
5. Clean the pre-cleaner in liquid detergent and water. Let it fully air dry. DO NOT
lubricate the pre-cleaner.
6. Assemble the dry pre-cleaner (E, Figure 20) to the filter (D).
7. Install the filter (D, Figure 20) and close the latch (C).
8. Install the cover (B, Figure 20) and close with the fastener(s).
Servicing the Fuel System
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
• If fuel spills, wait until it dries before you start the engine.
Fuel Filter, if installed
1. Before you replace the fuel filter (A, Figure 21), drain the fuel tank or close the fuel
shut-off valve. If the fuel tank is not drained, fuel leakagecanoccur and cause a fire
or explosion.
2. Squeeze the tabs (B, Figure 21) on the clamps (C) with pliers.Move the clamps
away from the fuel filter (A).
3. Twist and pull the fuel lines (D,Figure 21) off of the fuel filter.
4. Examinethe fuel lines (D, Figure 21) for cracks or leaks. If it is necessary, replace
the fuel lines.
5. Replace the fuel filter (A, Figure 21).
6. Attach the fuel lines (D, Figure 21) with clamps (C).
Servicing the Cooling System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible debris, such as leaves, grass, and brush can catch fire.
• Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
• Remove debris from the muffler and engine.
NOTICE
Do not use water to clean the engine. Water could cause contamination of the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can stop the air flow and cause the engine to
become too hot and result in unsatisfactory performance and decrease engine life.
1. Use a brush or dry cloth to remove debris from the air intake area (A, Figure 22).
2. Keep linkage, springs, and controls (B, Figures 22, 23) clean.
3. Keep the area around and behind the mufflerfree of combustible debris.
4. Make sure the oil cooler fins (C, Figures 22, 23), if equipped, are free of dirt and
debris.
5. Loosen the fastener(s) (D, Figure 22) and remove the air filter cover (E).
6. Loosen the fastener(s) (F, Figure 22) and remove the debris access panels (G,
Figure 23). Remove grass and debris that has collected on the cylinders.
7. Install the debris access panels (G, Figure 23) and attach with fastener(s) (F, Figure
22).
8. Install the air filter cover (E, Figure 22) and attach with fastener(s) (D).
After a period of time, debris can collect in the cylinder cooling fins and cause the engine
to overheat. This debris cannot be removed without partial disassembly of the engine.
As recommended in the Maintenance Schedule, have a Briggs & Stratton Authorized
Service Dealer inspect and clean the air cooling system.
Storage
Fuel Storage
Keep the engine level at the correct operating position. Fill the fuel tank (A, Figure 24)
with fuel. For fuel expansion, do not fill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days.The
use of an alcohol-free fuel stabilizer and ethanol treatment in the fuel storage container
is recommended. This keeps fuel fresh and decreases fuel-related problems or
contamination in the fuel system.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained
into an approved container. Operate the engine until it is out of fuel.
NOTE:DO NOT run the Electronic Fuel Injection engine out of fuel. Fuel pump damage
can occur. Make sure to add the correct amount of fuel stabilizer to the fuel tank, and
run the engine for 30 minutes.
Engine Oil
While the engine is still warm, change the engine oil. Refer to Change the Engine Oil
section.
Troubleshooting
Assistance
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.COM or call
1-800-444-7774 (in USA).
Specifications
Specifications and Service Parts
MODEL: 490000
Displacement 49.42 ci ( 810 cc)
Bore 3.300 in (83,81 mm)
Stroke 2.890 in (73,41 mm)
Oil Capacity 66 - 68 oz (1,9 - 2,0 L)
Oil Capacity - (Models with Oil Xtend) 75 oz (2,2 L)
Spark Plug Gap .030 in (,76 mm)
Spark Plug Torque 175 lb-in (19.2 Nm)
Armature Air Gap - EFI Models .028 - .052 in (,07 - 1,32 mm)
Armature Air Gap -Carburetor Models .008 - .012 in (,20 - ,30 mm)
Intake Valve Clearance .004 - .006 in (,10 - ,15 mm)
11
Exhaust Valve Clearance .004 - .006 in (,10 - ,15 mm)
Not for
Reproduction
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10°F (5.6°C) above 77° F (25°C). The engine will operate satisfactorily
at an angle up to 25°. Refer to the equipment Operator's Manual for safe permitted
operating limits on slopes.
MODELS: 490000
Service Part Part Number
Cyclonic Air Filter 798897
Air Filter, Pre-cleaner 593217
Oil - SAE 30 100028
Oil Filter, Standard - Black 492932S
Oil Filter, High Efficiency - Yellow 696854
Oil Filter, High Efficiency - Orange 798576
Oil Filter, Oil Xtend 84007055
Fuel Filter 84001895
Fuel Filter - EFI 845125
Resistor Spark Plug 491055S
Long Life Platinum Spark Plug 5066K
Spark Plug Wrench 19576S
Spark Tester 84003327
We recommend that you see a Briggs & Stratton Authorized Dealer for all maintenance
and servicing of the engine and engine parts.
Power Ratings
The gross power rating for individual gasoline engine models is labeled in accordance
with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque
Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM
for all others; horsepower values are derived at 3600 RPM. The gross power curves
can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with
exhaust and air cleaner installed whereas gross power values are collected without
these attachments. Actual gross engine power will be higher than net engine power and
is affected by, among other things, ambient operating conditions and engine-to-engine
variability. Given the wide array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not limited to, the
variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel
pump, etc.), application limitations, ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,
Briggs & Stratton may substitute an engine of higher rated power for this engine.
Warranty
Briggs & Stratton® Engine Warranty
Effective March 2023
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will
repair or replace, free of charge, with a new, reconditioned or re-manufactured part,
at the sole discretion of Briggs & Stratton, any part that is defective in material or
workmanship or both. Transportation charges on product submitted for repair or
replacement under this warranty must be borne by purchaser. This warranty is effective
for and is subject to the time periods and conditions stated below. For warranty
service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM. The purchaser must contact the Authorized Service
Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to one year
from purchase, or to the extent permitted by law. All other implied warranties
are excluded. Liability for incidental or consequential damages are excluded
to the extent exclusion is permitted by law. Some states or countries do not allow
limitations on how long an implied warranty lasts, and some states or countries donot
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation and exclusion may not apply to you. This warranty gives you specific legal
rights and you may also have other rights which vary from state to state and country to
country*.
Standard Warranty Terms 1, 2
Vanguard®; CXi Series
Consumer Use - 36 months
Standard Warranty Terms 1, 2
Commercial Use - 36 months
XR Series
Consumer Use - 24 months
Commercial Use - 24 months
All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve
Consumer Use - 24 months
Commercial Use - 12 months
All Other Engines
Consumer Use - 24 months
Commercial Use - 3 months
1These are our standard warranty terms, but occasionally there may be additional
warranty coverage that was not determined at time of publication. For a listing of
current warranty terms for your engine, go to BRIGGSandSTRATTON.COM or contact
your Briggs & Stratton Authorized Service Dealer.
2There is no warranty for engines on equipment used for prime power in place of a
utility; standby generators used for commercial purposes, utility vehicles exceeding 25
MPH, or engines used in competitive racing or on commercial or rental tracks.
The warranty period begins on the date of purchase by the first retail consumer or
commercial end user, and continues for the period of time stated in the table above.
“Consumer use” means personal residential household use by a retail consumer.
“Commercial use” means all other uses, including use for commercial, income
producing or rental purposes. Once an engine has experienced commercial use,
it shall thereafter be considered as a commercial use engine for purposes of this
warranty.
No warranty registration is necessary to obtain warranty on Briggs & Stratton
products. Save your proof of purchase receipt. If you do not provide proof of the
initial purchase date at the time warranty service is requested, the manufacturing
date of the product will be used to determine the warranty period.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only,
and not replacement or refund of the equipment to which the engine may be mounted.
Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered
under this warranty. Similarly, warranty is not applicable if the engine has been altered
or modified or if the engine serial number has been defaced or removed. This warranty
does not cover engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater
than 10%, or the use of alternative fuels such as liquefied petroleum or natural gas
on engines not originally designed/manufactured by Briggs & Stratton to operate
on such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or
reassembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or
excessive v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment
controls, etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or
unbalanced cutter blades or impellers, or improper coupling of equipment
components to the crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of
equipment, or improper engine installation.
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM or by calling 1-800-444-7774 (in USA).
80114782(Revision B)
Briggs & Stratton Emissions Warranty
U.S. EPA and Briggs & Stratton, LLC Emissions Control Warranty - Your
Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-
Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The U.S. EPA and Briggs & Stratton (B&S) are pleased to explain the exhaust
emissions (“emissions”) control system warranty on your 2023-2025 engine. New
12 BRIGGSandSTRATTON.COM
Not for
Reproduction
small off-road engines and large spark ignited engines less than or equal to 1.0 liter
must be designed, built, and equipped to meet stringent anti-smog standards.B&S
must warrant the emissions control system on your engine for the periods of time
listed below provided there has been no abuse, neglect or improper maintenance of
your small off-road engine or equipment leading to the failure of the emissions control
system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components.Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.If any
emissions-related part on your engine is defective, the part will be repaired or replaced
by B&S.
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual.B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
• As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
• You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days.If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as
to conform with all applicable regulations; that it is free from defects in material
and workmanship that could cause the failure of a warranted part; and that it is
identical in allmaterial respects to the engine described in the manufacturer’s
application for certification. The warranty period begins on the date the engine or
equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the period of
time prior to the first scheduled replacement point for that part. If the part fails
prior to the first scheduled replacement, the part will be repaired or replaced
by B&S at no charge to the owner. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first
scheduled replacement point for the part.
• Add-on or modified parts that are not exempted may not be used. The use of
any non-exempted add-on or modified parts by the owner will be grounds for
disallowing a warranty claim. The manufacturer will not be liable to warrant
failures of warranted parts caused by the use of a non-exempted add-on or
modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80130178 Revision A
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty -
Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "Z" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Zx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust emissions (“emissions”) control system warranty on
your 2023-2025 engine. In California, new small off-road engines and large spark
ignited engines less than or equal to 1.0 liter must be designed, built, and equipped
to meet the State’s stringent anti-smog standards.B&S must warrant the emissions
control system on your engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components.Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.If any
emissions-related part on your engine is defective, the part will be repaired or replaced
by B&S.
13
Not for
Reproduction
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual.B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
• As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
• You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days.If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as to
conform with all applicable regulations adopted by the Air Resources Board; that
it is free from defects in material and workmanship that could cause the failure
of a warranted part; and that it is identical in allmaterial respects to the engine
described in the manufacturer’s application for certification. The warranty period
begins on the date the engine or equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance inthe Operator’s Manual supplied, is warranted for the period of
time prior to the first scheduled replacement point for that part. If the part fails
prior to the first scheduled replacement, the part will be repaired or replaced
by B&S at no charge to the owner. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first
scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources Board
may not be used. The use of any non-exempted add-on or modified parts by
the owner will be grounds for disallowing a warranty claim. The manufacturer
will not be liable to warrant failures of warranted parts caused by the use of a
non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
The Emissions Durability Period describes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, the Emissions Durability Period of an engine with an intermediate rating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
14 BRIGGSandSTRATTON.COM
Not for
Reproduction
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80130057 Revision A
Briggs & Stratton Emissions Warranty
U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement -
Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "J" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Jx)
The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust
emissions control system warranty on your Model Year 2023-2025 engine. In the U.S,
new small off-road engines and large spark ignited engines less than or equal to 1.0
liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S
must warrant the emissions control system on your engine for the periods of time listed
below provided there has been no abuse, neglect, or improper maintenance of your
engine leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.If any
emissions-related part on your engine is defective, the part will be repaired or replaced
by B&S.
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the performance of the required
maintenance listed in your Operator’s Manual. B&S recommends that you
retain all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or your failure to ensure the
performance of all scheduled maintenance.
• As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect,
improper maintenance, or unapproved modifications.
• You are responsible for presenting your engine to a B&S distribution center,
or service center, as soon as a problem exists. The warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as to
conform with all applicable regulations under Section 213 of the Clean Air Act that
is free from defects in material and workmanshipthat could cause the failure of a
warranted part; and that is identical in all material respects to the engine described
in the manufacturer’s application for certification. The warranty period begins on
the date the engine or equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operator's Manual supplied, is warranted for the period of
time prior to the first scheduled replacement point for that part. If the part fails
prior to the first scheduled replacement, the part will be repaired or replaced
by B&S at no charge to the owner. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first
scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the U.S. EPA may not be
used. The use of any non-exempted add-on or modified parts by the owner
will be grounds for disallowing a warranty claim. The manufacturer will not
be liable to warrant failures of warranted parts caused by the use of a non-
exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label indicates the number of
operating hours for which the engine has been shown to meet Federal emissions
requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80127222 Revision A
15
Not for
Reproduction
Información general
Este manual contiene información de seguridad sobre los peligros y riesgos
relacionados con el motor y cómo prevenirlos. También contiene el correcto
funcionamiento y mantenimiento de este motor. Es importante que lea, comprenda y
obedezca estas instrucciones. Conserve este manual para referencia futura.
NOTA:Las figuras e ilustraciones en este manual sirven solo para información y
pueden ser diferentes a su modelo. Utilice las cifras que se alinean con la configuración
de su motor. Si es necesario, hable con un distribuidor de servicio autorizado.
Registre la fecha de compra, el modelo del motor, el tipo, la versión y el número
de serie del motor para las piezas de repuesto. Estos números están en su motor.
Consulte la secciónCaracterísticas y controles.
Fecha de compra
Modelo del motor - Tipo - Reglaje
Número de Serie del motor
Información de contacto de la oficina en
Europa
Si tiene preguntas relacionadas con las emisiones europeas, póngase en contacto con
nuestra oficina en Europa en:
Max-Born-Straße2, 68519 Viernheim, Alemania.
EtapaV (5) de la Unión Europea (UE):
Valores del dióxido de carbono (CO2)
Ingrese CO2 en la ventana de búsqueda en BriggsandStratton.com. para encontrar los
valores de dióxido de carbono de los motores de Briggs & Stratton con certificado de
aprobación tipo UE.
Información de reciclaje
Recicle todos los cartones, cajas, aceite usado y baterías
según lo especifiquen las regulaciones gubernamentales.
Seguridad del operador
Símbolo de alerta de seguridad y palabras de
señalización
El símbolo de alerta de seguridad identifica información de seguridad
sobre peligros que podrían provocar lesiones personales. Se usa una palabra
de señalización (PELIGRO, ADVERTENCIA, o PRECAUCIÓN) para indicar la
probabilidad y la gravedad potencial de las lesiones. Además, se usa un símbolo de
peligro para representar el tipo de riesgo.
PELIGRO indica un riesgo que, si no se evita, ocasionará la muerte o lesiones
graves.
ADVERTENCIA indica un riesgo que, si no se evita, podría ocasionar la muerte o
lesiones graves.
PRECAUCIÓN indica un riesgo que, si no se evita, podría ocasionar lesiones
menores o moderadas.
AVISO indica información que se considera importante pero que no está relacionada
con un peligro.
Símbolos de peligro y significados
Información de seguridad
sobre peligros que pueden
conllevar a lesiones
personales.
Lea y entienda el Manual
del operador antes
de operar y realizar
mantenimientos a la
unidad.
Peligro de incendio Peligro de explosión
Peligro de descarga
eléctrica
Peligro de vapores tóxicos
Peligro de superficie
caliente
Peligro de retroceso
violento
Peligro de amputación:
piezas móviles
Nivel de combustible -
Máximo
No lo llene en exceso
Mensajes de seguridad
ADVERTENCIA
Este producto puede exponerlo a sustancias químicas, entre las que se incluyen
emisiones de escape de motor de gasolina, reconocidas por el estado de California
como causantes de cáncer, y monóxido de carbono, reconocido por el estado de
California como causante de defectos de nacimiento u otros problemas reproductivos.
Para obtener más información, visite www.P65Warnings.ca.gov.
ADVERTENCIA
Los motores Briggs & Stratton® no están diseñados, y no deben utilizarse, para
potenciar carritos motorizados; go karts; vehículos para niños; vehículos recreativos;
vehículos deportivos todo terreno (ATV); motocicletas; aerodeslizadores; equipo
aeronáutico; o vehículos utilizados en eventos de competencia que no estén avalados
por Briggs & Stratton. Para obtener información acerca de productos de carrera
profesionales, consulte www.briggsracing.com. Para usar el motor en ATV utilitarios
y sidebyside, comuníquese con el Centro de aplicaciones de potencia de Briggs &
Stratton llamando al 1-866-927-3349. El uso incorrecto del motor podría provocar
lesiones graves o la muerte.
ADVERTENCIA
El combustible y sus vapores son inflamables y explosivos. El fuego o una
explosión podrían provocar quemaduras o la muerte.
Cuando agregue combustible
• Detenga el motor. Antes de quitar la tapa del combustible, espere un mínimo de
dos(2) minutos para asegurarse de que el motor esté frío.
• Llene el tanque de combustible al aire libre o en un área con buena circulación
de aire.
• No ponga demasiado combustible en el tanque. Para permitir la expansión del
combustible, no llene el tanque de combustible arriba de la parte inferior del
cuello.
• Mantenga el combustible alejado de chispas, llamas abiertas, llamas piloto,
calor y otras fuentes de ignición.
• Examine frecuentemente las líneas de combustible, el tanque de combustible, la
tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace
las piezas dañadas.
• Si el combustible se derrama, espere a que se seque antes de arrancar el
motor.
Cuando arranque el motor
• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el limpiador
de aire (si tiene) estén correctamente instalados.
• No arranque el motor si retiró la bujía.
• Si el motor está inundado, lleve el estrangulador (si tiene) a la posición
ABIERTO o MARCHA. Mueva el acelerador (si tiene) a la posición RÁPIDO y de
arranque hasta que el motor se encienda.
• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.
• Puesto que los vapores son inflamables, no utilice fluidos de encendido
presurizados.
Cuando opere el equipo
• No incline el motor o el equipo en un ángulo que cause derramamiento del
combustible.
• No cebe el carburador (si tiene) para detener el motor.
• Nunca arranque u opere el motor sin el limpiador de aire (si tiene) o el filtro de
aire (si tiene).
16 BRIGGSandSTRATTON.COM
Not for
Reproduction
Cuando lleve a cabo mantenimiento
• Si drena el aceite desde el tubo de llenado de aceite superior, el tanque de
combustible debe estar vacío. Si no está vacío, puede producirse un derrame de
combustible y podría ocasionarse un incendio o una explosión.
• Durante el mantenimiento, si es necesario inclinar la unidad, asegúrese de
que el tanque de combustible, si está montado en el motor, esté vacío y
que el extremo del motor donde está la bujía esté elevado. Si el tanque de
combustible no está vacío, puede producirse un derrame de combustible y
podría ocasionarse un incendio o una explosión.
• Examine frecuentemente las líneas de combustible, el tanque de combustible, la
tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace
las piezas dañadas.
• No cambie el resorte del regulador, las conexiones u otras piezas para
aumentar la velocidad del motor.
• No golpee el volante con un martillo o un objeto duro. Esto podría provocar una
falla en el volante durante la operación.
• Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas
en la misma posición que las piezas originales. Otras piezas podrían provocar
daños o lesiones.
Cuando traslada la ubicación del equipo
• Asegúrese de que el tanque de combustible esté VACÍO o que la válvula de
cierre de combustible esté en la posición CERRADA.
Cuando el combustible o el equipo está almacenado con combustible en el
tanque de combustible
• Puesto que las luces piloto u otras fuentes de ignición pueden causar
explosiones, mantenga el combustible o el equipo lejos de hornos, estufas,
calentadores de agua u otros aparatos que tengan luces piloto.
ADVERTENCIA
El combustible y sus vapores son inflamables y explosivos. El fuego o una
explosión podrían provocar quemaduras o la muerte.
El arranque del motor causa una chispa que podría provocar un incendio o una
explosión.
• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.
• Puesto que los vapores son inflamables, no utilice fluidos de encendido
presurizados.
ADVERTENCIA
PELIGRO DE GAS NOCIVO. Las emisiones del motor contienen monóxido de
carbono, un gas nocivo que podría causar la muerte en minutos. Aunque no huela
los gases del escape, puede estar expuesto al peligroso gas de monóxido de
carbono. Si usted se siente enfermo, adormecido, o débil al utilizar este producto,
diríjase hacia un lugar con aire fresco DEINMEDIATO. Consulte a un médico. Es
probable que se haya intoxicado con monóxido de carbono.
• El gas de monóxido de carbono puede acumularse en los espacios habitados.
Para reducir el riesgo del gas de monóxido de carbono, SOLAMENTE opere
este producto al aire libre, lejos de ventanas, puertas y ventilaciones.
• Instale alarmas de monóxido de carbono operadas por baterías o alarmas
de monóxido de carbono para enchufar con batería de respaldo según lo
que especifiquen las instrucciones del fabricante. Los detectores de humo no
detectan el gas de monóxido de carbono.
• NO opere este producto en viviendas, garajes, sótanos, espacios reducidos,
cobertizos u otros espacios cerrados, incluso si usa ventiladores o deja las
puertas y ventanas abiertas a manera de ventilación. Después de la operación
de este producto, el monóxido de carbono puede acumularse rápidamente en
estos espacios y permanecer durante horas.
• SIEMPRE ubique este producto a favor del viento y mantenga el escape del
motor alejado de los espacios confinados.
ADVERTENCIA
La retracción rápida del cordón del arrancador (retroceso) tirará de su mano y
brazo hacia el motor más rápido de lo que puede sostenerlo. Podrían presentarse
roturas en los huesos, fracturas, contusiones, o torceduras.
• Para evitar el retroceso al arrancar el motor, hale del cordón del arrancador
lentamente hasta sentir resistencia y luego suéltelo rápidamente.
• Antes de arrancar el motor, desconecte o retire cualquier carga externa del
motor/equipo.
• Asegúrese de que los componentes del equipo acoplados directamente, entre
otros, cuchillas, propulsores, poleas y ruedas dentadas estén firmemente
acoplados.
ADVERTENCIA
Las partes giratorias pueden atrapar las manos, los pies, el cabello, la ropa o los
accesorios y provocar una amputación o laceración traumática.
• Opere el equipo con protectores correctamente instalados.
• Mantenga sus manos y pies alejados de las piezas giratorias.
• Quítese las joyas y asegúrese de que el pelo largo esté apartado de todas las
piezas giratorias.
• No use ropa suelta o artículos que puedan quedar atrapados.
ADVERTENCIA
Durante la operación, el motor y el silenciador se calientan. Si toca un motor
caliente, pueden producirse quemaduras térmicas.
Los materiales combustibles, como hojas, césped y hierbas se pueden inflamar.
• Antes de tocar el motor o el silenciador, detenga el motor y espere dos(2)
minutos. Asegúrese de que el motor y el silenciador se puedan tocar con
seguridad.
• Quite los residuos del silenciador y del motor.
Es una infracción del Código de Recursos Públicos de California (California Public
Resource Code), Sección4442, utilizar u operar el motor en cualquier terreno forestal o
cubierto por árboles o césped, a menos que el sistema de escape esté equipado con un
supresor de chispas, en virtud de la Sección4442, el cual se debe mantener en buenas
condiciones de operación. Es posible que otros estados o jurisdicciones federales
cuenten con leyes similares; consulte la Regulación Federal 36CFR Sección261.52.
Póngase en contacto con el vendedor, el distribuidor o el fabricante del equipo original
para obtener un extintor de chispas diseñado para el sistema de escape instalado en
este motor.
ADVERTENCIA
La chispa accidental del motor puede provocar una descarga eléctrica, un
incendio o una explosión y podría resultar en un enredo, una amputación
traumática o una laceración.
Antes de que realice ajustes o reparaciones:
• Desconecte todos los cables de las bujías y manténgalos alejados de las bujías.
• Desconecte el cable de la batería del terminal negativo de la batería (solo
motores con arranque eléctrico).
• Use solamente las herramientas correctas.
Cuando verifique si hay chispa:
• Use un probador de bujías aprobado.
• No revise si hay chispa con la bujía extraída.
ADVERTENCIA
Los vapores del combustible son inflamables y explosivos. El fuego o una
explosión podrían provocar quemaduras o la muerte.
Si siente olor a gas
• No arranque el motor.
• No encienda interruptores eléctricos.
• No use un teléfono en las cercanías.
• Desaloje el área.
• Comuníquese con el proveedor de gas o con los bomberos.
Características y controles
Controles del motor
Compare las letras de las leyendas en las Figuras 1, 2 y 3con los controles del motor en
la lista a continuación:
A. Números de identificación del motor Modelo - Tipo - Código
B. Bujía
C. Filtro de aire
D. Tapones de la varilla
E. Tapón de drenaje de aceite, si está instalado
F. Rejilla de toma de aire
G. Filtro de aceite
H. Arrancador eléctrico
17
Not for
Reproduction
I. Carburador
J. Filtro de combustible (si está instalado)
K. Bomba de combustible (si está instalada)
L. Drenaje rápido de aceite (si está instalado)
M. Radiador de aceite (si está instalado)
N. Unidad de control eléctrico (si está instalada)
O. Filtro de aceite remoto (con Xtend™, si está instalado)
P. Inserción del tapón de aceite (con Oil Xtend, si está instalado)
Q. Llenado de aceite alternativo (con Oil Xtend, si está instalado)
Símbolos de control del motor y significados
Velocidad del motor -
RÁPIDA
Velocidad del motor -
LENTA
Velocidad del motor -
DETENER
ENCENDIDO/APAGADO
Arranque del motor
Estrangulador CERRADO
Arranque del motor
Estrangulador ABIERTO
Tapa del combustible
Válvula de cierre de
combustible - ABIERTO
Válvula de cierre de
combustible - CERRADO
Operación
Recomendaciones sobre el aceite
Capacidad de aceite: Consulte la sección Especificaciones.
Recomendamos el uso de aceites Briggs&Stratton® con garantía certificada para
un mejor rendimiento. Se permiten otros aceites detergentes de alta calidad, si están
clasificados para servicio SF, SG, SH, SJ o superior. No use aditivos especiales.
Use el cuadro para seleccionar la mejor viscosidad para el margen de temperatura
exterior que se espera. Los motores de la mayoría de los equipos eléctricos para
exteriores funcionan bien con aceite sintético 5W-30. Para equipos que operan a altas
temperaturas, el aceite sintético Vanguard® 15W-50 brinda la mejor protección.
A SAE30 - El uso de SAE30 a temperaturas inferiores a 40°F (4°C) provocará
dificultades de arranque.
B 10W-30 - El uso de 10W-30 a temperaturas mayores a 80°F (27°C) puede
provocar un aumento en el consumo de aceite. Verifique el nivel de aceite con
frecuencia.
C 5W-30
D 5W-30 sintético
EVanguard®Sintético 15W-50
Verifique el nivel de aceite
Antes de verificar o agregar aceite
• Asegúrese de que el motor esté nivelado.
• Limpie todos los desechos del área de llenado de aceite.
• Consulte la sección Especificacionespara obtener la capacidad de aceite.
AVISO
Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o
distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el
motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue
el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor
sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la
garantía.
1. Retire la varilla indicadora de nivel (A, Figura 4) y séquela con un paño limpio.
2. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 4).
3. Retire la varilla y revise el nivel de aceite. Asegúrese de que el nivel de aceite
esté en la parte superior del indicador de lleno (B, Figura 4) de la varilla indicadora
de nivel de aceite.
4. Si el nivel de aceite es bajo, agregue aceite lentamente en el llenado de aceite del
motor (C, Figura 4). No agregue demasiado aceite.
5. Espere un minuto y verifique el nivel de aceite. Asegúrese de que el nivel de
aceite sea el correcto.
6. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 4).
Sistema de protección de bajo nivel de aceite (si
está instalado)
En algunos motores se ha instalado un sensor de bajo nivel de aceite. Si el nivel
de aceite está bajo, el sensor mostrará una luz de advertencia o detendrá el motor.
Detenga el motor y siga los pasos a continuación antes de arrancar el motor.
• Asegúrese de que el motor esté nivelado.
• Haga una comprobación del nivel de aceite. Consulte la secciónVerificación
del nivel de aceite.
• Si el nivel de aceite es bajo, agregue la cantidad correcta de aceite. Arranque
el motor y asegúrese de que la luz de advertencia (si está instalada) no se
encienda.
• Si el nivel de aceite es bajo, no arranque el motor. Comuníquese con un
distribuidor de servicio autorizado de Briggs & Stratton para corregir el problema
del aceite.
Recomendaciones acerca del combustible
El combustible debe cumplir con estos requisitos:
• Gasolina limpia, fresca y sin plomo.
• Un mínimo de 87octanos/87AKI (91RON). Para uso en grandes alturas,
consulte a continuación.
• Se permite gasolina con hasta un 10% de etanol (gasohol).
AVISO
No utilice gasolina no aprobada, como la E15 y la E85. No mezcle la gasolina con
aceite ni cambie el motor para usarlo con combustibles alternativos. El uso de
combustibles no aprobados podría provocar daños a los componentes del motor, lo
que no será reparado bajo la garantía.
Para proteger el sistema de combustible de la formación de goma y la corrosión,
mezcle el combustible con un estabilizador de combustible sin alcohol y un tratamiento
de etanol. Consulte la sección Almacenamiento. No todos los combustibles son
iguales. Si ocurren problemas de arranque o de rendimiento, cambie el proveedor o
la marca del combustible. Este motor está certificado para funcionar con gasolina.
El sistema de control de emisiones para motores carburados es EM (modificaciones
del motor). Los sistemas de control de emisiones para motores con inyección de
combustible electrónica son ECM (módulo de control del motor), MFI (inyección
multipunto), TBI (inyección al cuerpo de aceleración) y, si lo tiene, un O2S (sensor de
oxígeno).
Gran altura
En alturas de más de 5000pies (1524metros), se permite una gasolina con un mínimo
de 85octanos/85AKI (89RON).
Para motores carburados, se requiere realizar el ajuste de gran altura para mantener
el rendimiento. El funcionamiento sin este ajuste provocará una disminución en
el rendimiento y un aumento en el consumo de combustible y en las emisiones.
Comuníquese con un distribuidor de Servicio Autorizado por Briggs & Stratton para
obtener información sobre el ajuste de gran altura. No se recomienda operar la
máquina a alturas menores de 2500pies (762metros) con el ajuste de gran altura.
En el caso de motores con inyección de combustible electrónica (EFI), no se requiere
un ajuste de gran altura.
18 BRIGGSandSTRATTON.COM
Not for
Reproduction
Agregar combustible
ADVERTENCIA
El combustible y sus vapores son inflamables y explosivos. El fuego o una
explosión podrían provocar quemaduras o la muerte.
Cuando agregue combustible
• Detenga el motor. Antes de quitar la tapa del combustible, espere un mínimo de
dos(2) minutos para asegurarse de que el motor esté frío.
• Llene el tanque de combustible al aire libre o en un área con buena circulación
de aire.
• No ponga demasiado combustible en el tanque. Para permitir la expansión del
combustible, no llene el tanque de combustible arriba de la parte inferior del
cuello.
• Mantenga el combustible alejado de chispas, llamas abiertas, llamas piloto,
calor y otras fuentes de ignición.
• Examine frecuentemente las líneas de combustible, el tanque de combustible, la
tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace
las piezas dañadas.
• Si el combustible se derrama, espere a que se seque antes de arrancar el
motor.
1. Limpie la suciedad y los desechos en el área de la tapa de llenado de combustible.
Retire la tapa de llenado de combustible.
2. Llene el tanque de combustible (A, Figura 5) con combustible. Puesto que el
combustible se expandirá, no llene más arriba de la parte inferior del cuello del
tanque de combustible (B).
3. Instale la tapa de llenado de combustible.
Arranque del motor
ADVERTENCIA
La chispa accidental del motor puede provocar una descarga eléctrica, un
incendio o una explosión y podría resultar en un enredo, una amputación
traumática o una laceración.
Antes de que realice ajustes o reparaciones:
• Desconecte todos los cables de las bujías y manténgalos alejados de las bujías.
• Desconecte el cable de la batería del terminal negativo de la batería (solo
motores con arranque eléctrico).
• Use solamente las herramientas correctas.
Cuando verifique si hay chispa:
• Use un probador de bujías aprobado.
• No revise si hay chispa con la bujía extraída.
ADVERTENCIA
La retracción rápida del cordón del arrancador (retroceso) tirará de su mano y
brazo hacia el motor más rápido de lo que puede sostenerlo. Podrían presentarse
roturas en los huesos, fracturas, contusiones, o torceduras.
• Para evitar el retroceso al arrancar el motor, hale del cordón del arrancador
lentamente hasta sentir resistencia y luego suéltelo rápidamente.
• Antes de arrancar el motor, desconecte o retire cualquier carga externa del
motor/equipo.
• Asegúrese de que los componentes del equipo acoplados directamente, entre
otros, cuchillas, propulsores, poleas y ruedas dentadas estén firmemente
acoplados.
ADVERTENCIA
PELIGRO DE GAS NOCIVO. Las emisiones del motor contienen monóxido de
carbono, un gas nocivo que podría causar la muerte en minutos. Aunque no huela
los gases del escape, puede estar expuesto al peligroso gas de monóxido de
carbono. Si usted se siente enfermo, adormecido, o débil al utilizar este producto,
diríjase hacia un lugar con aire fresco DEINMEDIATO. Consulte a un médico. Es
probable que se haya intoxicado con monóxido de carbono.
• El gas de monóxido de carbono puede acumularse en los espacios habitados.
Para reducir el riesgo del gas de monóxido de carbono, SOLAMENTE opere
este producto al aire libre, lejos de ventanas, puertas y ventilaciones.
• Instale alarmas de monóxido de carbono operadas por baterías o alarmas
de monóxido de carbono para enchufar con batería de respaldo según lo
que especifiquen las instrucciones del fabricante. Los detectores de humo no
detectan el gas de monóxido de carbono.
• NO opere este producto en viviendas, garajes, sótanos, espacios reducidos,
cobertizos u otros espacios cerrados, incluso si usa ventiladores o deja las
puertas y ventanas abiertas a manera de ventilación. Después de la operación
de este producto, el monóxido de carbono puede acumularse rápidamente en
estos espacios y permanecer durante horas.
• SIEMPRE ubique este producto a favor del viento y mantenga el escape del
motor alejado de los espacios confinados.
AVISO
Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o
distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el
motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue
el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor
sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la
garantía.
NOTA:Su equipo podría tener controles remotos. Consulte el manual del equipo para
conocer la ubicación y la operación de los controles remotos.
Tipos de sistemas de encendido
Antes de arrancar el motor, debe conocer el tipo de sistema de encendido de su
motor. Su motor tiene uno de estos tipos de sistemas de encendido.
•Sistema de inyección de combustible electrónica (EFI): Un sistema EFI no
tiene un estrangulador ni un cebador.
•Sistema electrónico para la administración de combustible: Un sistema
electrónico para la administración de combustible tiene una unidad de control
electrónico que monitorea las condiciones del motor y la temperatura. No tiene
un estrangulador manual ni un cebador.
•Sistema del estrangulador: Este tipo de sistema tiene un estrangulador que
se debe utilizar en temperaturas frías. Algunos modelos tienen un control de
estrangulamiento separado pero algunos tienen una combinación de control de
ahogador y acelerador. Este tipo no tiene cebador.
Sistema de inyección de combustible electrónica(EFI)
1. Revise el aceite del motor. Consulte la sección Verificación del nivel de aceite.
2. Asegúrese de que los controles de transmisión del equipo, si están instalados,
estén desactivados.
3. Mueva la válvula de cierre de combustible (A, Figura 6), si está instalada, a la
posición ABIERTO.
4. Mueva el control del acelerador (B, Figura 6), si está instalado, a la posición
RÁPIDO. Opere el motor en la posición RÁPIDO.
NOTA:En los modelos con control electrónico del acelerador, el control del acelerador
puede estar en cualquier posición al arrancar el motor.
5. Gire el interruptor de arranque eléctrico (D, Figura 6) a la posición ENCENDIDO o a
la posición ARRANQUE.
AVISOPara prolongar la vida útil del arrancador, haga ciclos cortos de arranque (cinco
segundos como máximo). Espere un minuto entre los ciclos de arranque.
Si el motor no arranca después de 3o 4intentos, póngase en contacto con su
distribuidor local o vaya a BRIGGSandSTRATTON.COMo llame al 1-800-444-7774(en
EE.UU.).
Sistema electrónico para la administración de combustible
1. Revise el aceite del motor. Consulte la sección Revisión y adición de aceite.
2. Asegúrese de que los controles de transmisión del equipo, si están instalados,
estén desactivados.
3. Mueva la válvula de cierre de combustible (A, Figura7), si está instalada, a la
posición ABIERTO.
4. Mueva el control del acelerador (B, Figura7), si está instalado, a la posición
RÁPIDO. Opere el motor en la posición RÁPIDO.
5. Arranque por rebobinado, si está instalado: Gire el interruptor de llave (D,
Figura7) a la posición ENCENDIDO/ARRANQUE.
19
Not for
Reproduction
6. Arranque por rebobinado, si está instalado: Sostenga firmemente el mango
del cordón de arranque (E, Figura 7). Tire del mango del cordón del arrancador
lentamente hasta sentir una resistencia y, a continuación, tire de él rápidamente.
ADVERTENCIA
La retracción rápida de la cuerda de arranque (retroceso violento) impulsará su mano
y su brazo hacia el motor antes de que pueda soltarla. Esto podría ocasionar roturas
de huesos, fracturas, hematomas o torceduras. Para evitar el retroceso al arrancar
el motor, hale del cordón del arrancador lentamente hasta sentir resistencia y luego
suéltelo rápidamente.
7. Gire el interruptor de llave (D, Figura7)a la posición ENCENDIDO/ARRANQUE.
AVISOPara prolongar la vida útil del arrancador, haga ciclos cortos de arranque (cinco
segundos como máximo). Espere un minuto entre los ciclos de arranque.
NOTA:Si el motor no arranca después de 2 a 3 intentos, comuníquese con un
distribuidor local, visiteBRIGGSandSTRATTON.COMo llame al1-800-444-7774(en
EE.UU.).
Sistema del estrangulador
1. Revise el aceite del motor. Consulte la secciónRevisión y adición de aceite.
2. Asegúrese de que los controles de transmisión del equipo, si están instalados,
estén desactivados.
3. Mueva la válvula de cierre de combustible (A, Figura8), si está instalada, a la
posición ABIERTO.
4. Mueva el control del acelerador (B, Figura8), si está instalado, a la posición
RÁPIDO. Opere el motor en la posición RÁPIDO.
5. Mueva el control del ahogador (C, Figura 8) a la posición de CERRADO.Para los
modelos con una combinación de control de ahogador/acelerador (B, C, Figura 8)
mueva el control a la posición CHOKE (ahogador).
NOTA:Generalmente no es necesario usar el estrangulador cuando arranca un motor
caliente.
6. Arranque por rebobinado, si está instalado: Gire el interruptor de llave (D,
Figura8), si está instalado, a la posición ENCENDIDO/ ARRANQUE.
7. Arranque por rebobinado, si está instalado: Sostenga firmemente el mango del
cable de arranque (E, Figura 8), si está instalado. Tire lentamente del mango del
cordón de arranque (E) hasta sentir una resistencia y, a continuación, tire de él
rápidamente.
8. Mueva el interruptor de arranque eléctrico, si está instalado, a la posición
ENCENDIDO/ARRANQUE.
AVISO
Para prolongar la vida útil del arrancador, haga ciclos cortos de arranque (cinco
segundos como máximo). Espere un minuto entre los ciclos de arranque.
9. Cuando se caliente el motor, mueva el control del estrangulador (C, Figura8) a la
posición ABIERTO.
NOTA:Si el motor no arranca después de 2 o 3 intentos, póngase en contacto con su
distribuidor local o vaya a BRIGGSandSTRATTON.COM o llame al 1-800-444-7774.
Detención del motor
ADVERTENCIA
El combustible y sus vapores son inflamables y explosivos. El fuego o una
explosión podrían provocar quemaduras o la muerte.
• No cebe el carburador (si tiene) para detener el motor.
1. Desactive los controles del equipo. Consulte el manual del equipo para conocer la
ubicación y el funcionamiento de los controles remotos.
2. Mueva el control del acelerador (B, Figura 9), si está instalado, a la posición
LENTO.
3. Gire el interruptor de llave (D, Figura9) a la posición APAGADO o a la posición
DETENER. Retire la llave y manténgala en un sitio seguro fuera del alcance de los
niños
4. Con el control del acelerador en la posición LENTO, coloque el interruptor
de arranque eléctrico (D, Figura 9) en la posición APAGADO. Retire la llave.
Manténgala en un lugar seguro fuera del alcance de los niños.
5. Después de que se haya detenido el motor, mueva la válvula de cierre de
combustible (A, Figura9), si está instalada, a la posición CERRADO.
Mantenimiento
Información de mantenimiento
ADVERTENCIA
El combustible y sus vapores son inflamables y explosivos. El fuego o una
explosión podrían provocar quemaduras o la muerte.
Durante el mantenimiento, si es necesario inclinar la unidad, asegúrese de que el
tanque de combustible, si está montado en el motor, esté vacío y que el extremo del
motor donde está la bujía esté elevado. Si el tanque de combustible no está vacío,
puede producirse un derrame de combustible y podría ocasionarse un incendio o una
explosión. Si el motor está inclinado en una dirección diferente, no arrancará fácilmente
debido a la contaminación del filtro de aire o de la bujía por aceite o combustible.
ADVERTENCIA
La chispa accidental del motor puede provocar una descarga eléctrica, un
incendio o una explosión y podría resultar en un enredo, una amputación
traumática o una laceración.
Antes de que realice ajustes o reparaciones:
• Desconecte todos los cables de las bujías y manténgalos alejados de las bujías.
• Desconecte el cable de la batería del terminal negativo de la batería (solo
motores con arranque eléctrico).
• Use solamente las herramientas correctas.
Cuando verifique si hay chispa:
• Use un probador de bujías aprobado.
• No revise si hay chispa con la bujía extraída.
ADVERTENCIA
Todos los componentes utilizados para montar este motor deben permanecer
en la posición inicial para su correcta operación. Pueden producirse daños o
lesiones si se utilizan piezas incorrectas o no se sustituyen todas las piezas del
motor.
• Las piezas de repuesto deben ser del mismo diseño y deben instalarse en la
misma posición que las piezas iniciales.
• Si está instalado, no cambie el resorte del regulador, las conexiones u otras
piezas para aumentar la velocidad del motor.
Consulte a un distribuidor de servicio autorizado de Briggs & Stratton para todo el
mantenimiento y servicio del motor y las piezas del motor.
Plan de mantenimiento
Tipo de filtro de aceite de motor
Acción de mantenimiento Ninguno Negro Amarillo/
Naranja
Oil Xtend
Solamente las primeras 5 horas
Cambie el aceite. ●
8 horas o diariamente1
Revise el nivel de aceite del
motor.
● ● ●
Limpie el área alrededor del
silenciador y los controles.
● ● ● ●
Cada 25horas o anualmente1
Limpie el filtro de aire2.● ● ● ●
Limpie el prefiltro (si está
instalado)2.
● ● ● ●
Cada 50horas o anualmente1
Realice el mantenimiento del
sistema de escape.
● ● ● ●
Cambie el aceite. ● ●
Reemplace el filtro de aceite (si
está instalado).
●
Cada 100horas o anualmente1
Cambie el aceite. ●
Reemplace el filtro de aceite (si
está instalado).
●
Cada 250horas o anualmente1
Reemplace la bujía. ● ● ● ●
20 BRIGGSandSTRATTON.COM
Not for
Reproduction
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Simplicity MANUALS, OPERATOR'S Manuel utilisateur
- Catégorie
- Accessoires pour véhicules automobiles
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
-
Simplicity MANUAL, OPERATOR'S Manuel utilisateur
-
-
-
Simplicity ENGINE, MODEL 106200, OIL BATH Manuel utilisateur
-
Simplicity 14B907-0110-B1 Manuel utilisateur
-
Simplicity 126M02-0122-B1 Manuel utilisateur
-
Simplicity 103M02-0120-H5 Manuel utilisateur
-
Simplicity 215802-3015-G5 Manuel utilisateur
-
Simplicity 21B977-0129-B1 Manuel utilisateur