Lifetime 90599 Le manuel du propriétaire

TOOLS REQUIRED TABLE OF CONTENTS

• Requires at least 493 lb (224 kg) of cement mix to ﬁ ll a

volume of 3.7 ft3 (0,105 m3).

• Requires, at least, 3 days for concrete to cure, plus

3–4 hours to complete assembly steps.

• At least 2 people recommended for setup.

Pour le français, voir la page 2. Para el español, ver la página 3.

ASSEMBLY INSTRUCTIONS

MODEL 90599

Save this instruction in the event that the manufacturer must be contacted for replacement parts.

BEFORE ASSEMBLY:

CONTACT LIFETIME CUSTOMER SERVICE:

Dial 1-800-225-3865

QUESTIONS? Model Number: 90599

Product ID:

For Customer Service in Mainland Europe

and the United Kingdom,

E-mail: [email protected]

Live Chat:

www.lifetime.com/customerservice/home

(Click on the "LIVE CHAT" tab)

7/16" (≈11 mm)

(x2)

(x1)

(x1) (x1)

1/2" (≈13 mm)

(x2)

(x1)

9/16" (≈14 mm)

(x2)

3/4" (≈19 mm)

(x2)

(x1)

Concrete Mix

493 lb (224 kg)

(x1)

Icon Legend...............................2

Warnings & Notices.....................3

Initial Setup...............................4

Pole Assembly..........................10

Backboard-to-Rim Assembly......14

Backboard-to-Pole Assembly......18

Parts Identiﬁ er.........................i–iv

Handle Assembly......................23

Final Assembly.........................30

Maintenance............................35

Warning Sticker........................36

Registration........................38

Warranty................................39

FRONT ADJUST®

BASKETBALL SYSTEM

(x1)

Bricks (x8–10)

2

• Indicates the parts to be used for a section.

• Indicates special heed should be taken when reading.

• Indicates the hardware to be used for a section.

• Indicates the tools to be used for a section.

• Indicates no hardware required for a speciﬁ c page.

• Indicates no parts required for a speciﬁ c section.

• Indicates to use/not to use an electric drill for a speciﬁ c step.

ICON LEGEND

• Indicates the use of a centerlock nut. A nut with this marking will require some effort to tighten.

This hardware was designed with this feature in order to prevent loosening later.

33

WARNINGS & NOTICES

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing

material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware

identiﬁ er and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the

risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

• If using a ladder during assembly, use extreme caution.

• Two capable adults are recommended for this operation.

• Check base daily for leakage. Leaks will cause system to fall.

• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.

• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.

SAFETY INSTRUCTIONS

4

INITIAL SET UP

1

ALE (x1)

(x1)

HARDWARE REQUIRED

PARTS REQUIRED

TOOLS REQUIRED

Metal Parts

Concrete mix

60-lb bags (≈x9)

(493 lb) (≈223,6 kg)

Bricks

(x8–10)

5

 SECTION 1 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

1

• IMPORTANT! Dig a round hole 24" (≈61 cm) deep and 18" (≈45.7 cm) in diameter. If you live in an area where frost heaves

may pose a problem, consult your local building inspector to determine the proper hole depth. The edge of the hole

should be ﬂ ush with the edge of the playing surface.

!• A ground sleeve is available as an alternative to cementing the pole into the ground. Please contact Customer Service for more information.

• The edge of the 18" (≈45.7 cm) diameter hole should touch the edge of

the playing surface.

(x1)

1.1

• Before digging, call to locate any buried utility lines.

• Avant de creuser, appelez pour localiser des utilités

publiques entérrées.

• Antes de cavar, llame para localizar las conexiones

de servicios públicos subterráneas.

CAUTION

! !

!

Playing Surface

Top view

24" (≈61 cm)

18" (≈45,7 cm)

Side view

6

 SECTION 1 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

• Stack bricks or patio blocks in the hole so the top of the stack measures 9.5" (≈24,1 cm) from the bottom of the hole (Fig.

1). The edge of the bricks should be about 2 1/2" (≈7 cm) from the playing surface (Fig. 2).

Fig. 1

Fig. 2

1.2

Playing Surface

24" (≈61cm)

18" (≈45,7 cm)

14.5"

(≈36,8 cm)

9.5"

(≈24,1 cm)

Side view

Top view

(x1)

2 1/2" (≈7 cm)

Bricks (x8–10)

7

 SECTION 1 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

1.2

(x1)

• Make a mark 14.5" (≈36.8 cm) from the dimpled end of the bottom pole (ALE) (do not scratch the

powder coating). Please, keep in mind this step when performing the next.

14.5 in/po (≈36.8 cm)

ALE

1.3

1.4

Concrete mix

420 lb (191 kg)

• Mix the concrete, following the directions on the bag.

Concrete mix

60-lb bag (≈x9)

(493 lb (≈223,6 kg))

8

 SECTION 1 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

1.5

!• Use a level to ensure the bottom pole is standing vertical. Form the cement into a downward slope away from the pole to allow water runoff. Failure to do

so may result in premature rusting of the pole.

(x1)

21" (≈53,3 cm)

18" (≈45,7 cm)

14.5"

(≈36,8 cm)

9.5"

(≈24,1 cm)

Side view

• 14.5" (≈36.8 cm) mark

18" (≈46 cm)

4" (≈10,2 cm)

Playing Surface

Fig. 1 Fig. 2

• Set the bottom of the bottom pole onto the bricks or patio blocks. The 14.5" (≈36.8 cm) mark on the pole should be ﬂ ush with the playing

surface (Fig. 1). If it is not ﬂ ush, the system will not adjust to the correct heights. The edge of the pole should be 4" (≈10.2 cm) from the playing surface

(Fig. 2) to ensure the back board overhangs the playing surface. If it is not, adjust it.

(x1)

9

 SECTION 1 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

• The slots at the top of the bottom pole must be parallel to the playing surface. Turn the pole, if necessary. Pour the mixed

concrete into the hole until it is ﬁ lled to the level of the playing surface and the 14.5" (≈36,8 cm) mark on the pole.

Form the concrete into a downward slope away from the pole to allow for runoff. Allow the concrete to cure for 72 hours.

1.6

14.5" (≈36,8 cm) mark

Downward slope

Playing surface • Stop assembly now. Do not continue the assembly

until the concrete has been allowed to set for at

least 72 hours (3 days). In humid climates or wet

weather, allow more time for the concrete to cure.

Do not proceed until the curing process is complete.

!

• Ne pas continuer l’assemblage jusqu’à ce que le

béton ait été permis durcir, au moins, 72 heures

(3 jours). Sous les climats humides, laisser plus de

temps pour que le béton durcisse. Ne pas continuer

jusqu’à ce que le durcissement soit complète.

• Pausar el ensamblaje ahora. No continuar

el ensamblaje hasta que el concreto haya sido

permitido curar, por lo menos, 72 horas (3 días).

En climas húmedos, dejar más tiempo a que

el concreto se cure. No continuar hasta que el

endurecimiento se termine.

WARNING / AVERTISSEMENT

ADVERTENCIA

(x1)

10

POLE ASSEMBLY

2

BCO

Metal Part

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

(2) (1)

9/16”

ADS (x2)*

ABZ (x2)*

ABB (x2)

AAF (x2)

ABE (x2)

ABR (x2) CIH (x2)*

*Note: Only one #14 x 1” Self-Tapping Screw (ABZ), one Domed Countersink

Washer (CIH) and one 1/4” x 3/4” Pan Head Screw (ADS) will be used for

this section. Save the remaining hardware for later in the assembly.

Scrap Wood

ALH (x1)

ALF (x1)

Warning Sticker

ALL (x1)

(1) (1)

11

TOOLS AND HARDWARE REQUIRED

 SECTION 2 (CONTINUED)

2.1 • Insert the 3/8” x 4” Hex Bolts (ABE) with the 3/8” Washers (AAF) into the Middle Pole (ALF) as shown. Then slide the 1/2” x

3.41” Spacers (ABR) onto the Hex Bolts.

ALF

ABE

ABR

Warning

Sticker

AAF

Large Holes

Small Holes

AAF (x2)

ABE (x2)

ABR (x2)

12

TOOLS AND HARDWARE REQUIRED

 SECTION 2 (CONTINUED)

2.2 • Place the Pole Bracket (ALL) onto the 3/8” x 4” Hex

Bolts (ABE), and attach it to the Middle Pole (ALF)

with the hardware shown.

• The 1/4” x 3/4” Screw should be ﬂ ush with the Pole,

but will spin freely once installed. Do not jam the Poles

together until instructed.

!

9/16" (x2)

2.3 • Align the hole in the Top Pole (ALH) with the slot in

the Middle Pole (ALF) and slide the Top Pole over the

Middle Pole. Insert a 1/4” x 3/4” Screw (ADS) through

a Domed Countersink Washer (CIH), into the small hole

in the Top Pole, and into the slot in the Middle

Pole as shown. The Screw head should ﬁ t into the

Countersink Washer.

ALF

ABB

ALL

ABE

ABB (x2) ADS (x1)

ALH

ALF

ALH

ALF

ADS

CIH

CIH (x1)

13

TOOLS AND HARDWARE REQUIRED

 SECTION 2 (CONTINUED)

• After the Poles have been seated, insert a #14 x 1”Self-Tapping Screw (ABZ) into the back of the Pole as shown.

2.5

2.4 • In order to seat the Poles, strike each end of the Pole very hard ﬁ ve to six times on a piece of scrap wood or cardboard.

This must be done even if the Poles cover the slots before seating has occurred.

If the Top Pole (ALH) does not completely cover the slots on the Middle Pole (ALF) after seating, DO NOT COMPLETE ASSEMBLY. Call

our Customer Service Department.

WARNING

The poles must be seated together! Even if the poles cover

the slots before seating, they must be struck on a hard

surface ﬁ ve to six times! Failure to seat the poles correctly

could allow the poles to separate during use, which could

lead to serious personal injuries or property damage.

Wood Block

ATTENTION: THIS STEP CANNOT BE REVERSED!

ALH

ALF

ALH

ALF

ABZ

ABZ (x1)

• Do not hit your feet with the Pole sections,

as serious injury could occur.

!

• THE SCREWS (ABZ) ARE DESIGNED TO DRILL

INTO THE METAL OF THE UNDERLYING POLE.

For ease of installation, chuck the Self-Drilling

Screws directly into the drill, or use a 3/8 in. (10

mm) Hex Driver.

!

14

BACKBOARD-TO-RIM ASSEMBLY

3

BCS

Metal Parts

Hardware Bag

PARTS REQUIRED

HARDWARE REQUIRED

ABD (x2)

5/16”

ABF (x2)

7/16”

AAM (x2)

ABK (x4)

5/16”

AJW (x2) APZ (x1)

AOW (x1)

AAV (x2)

DFE (x4)

AAA (x4)

AAJ (x2)

AJI (x1)

ALX (x1)

ALD (x1)

DFD (x1)

AMY (x2)

Plastic Parts

TOOLS REQUIRED

(2) (2) (2)

1/2” 7/16” 9/16”

15

TOOLS AND HARDWARE REQUIRED

 SECTION 3 (CONTINUED)

3.1 • Insert two Bolts (AAM) with Washers (ABD) and Rubber Washers (ABF) through the holes indicated in the back of the Rim (ALX) as

shown. Secure the hardware with two T-Nuts (AAJ).

1/2" (13 mm)

ABD (x2) ABF (x2)

AAM (x2)

AAJ (x2)

(x2)

(x1)

• Ensure that the tap bolts (AAM) are positioned on

the outside edge of the holes as shown.

• Do not overtighten the hardware so much that the

rubber washers bulge as shown.

!

AAJ

AAM

ABD

ABF

ALX

ABF ABF

AAJ

AAM

ABD

ABF

16

TOOLS AND HARDWARE REQUIRED

 SECTION 3 (CONTINUED)

1/2” (x2)

3.2 • Connect the Rim (ALX) and Plastic Guard (ALD) to the Backboard (AJI) with the hardware shown. Secure the 5/16” Nylock Flange

Nuts (ABK) onto the Tap Bolts (AAM).

ABK (x2)

APZ (x1)

APZ

ALX

ABK

ALD

AAM

AJI

DFD

17

TOOLS AND HARDWARE REQUIRED

 SECTION 3 (CONTINUED)

AAV

ABK

AOW

AJW

APZ

3.3

• Turn the Backboard Assemly over. Thread the 5/16” Jam Nuts (AAV) onto each end of the U-Bolt (APZ) as far as they

will go. Slide the Compression Springs (AJW) onto the U-Bolt, and place the Spring Retainer Plate (AOW) over the Com-

pression Springs. Secure the Plate to the Springs with the hardware shown.

• Attach the Backboard Brackets (AMY) to the Backboard using the hardware shown.

AAV (x2) ABK (x2)

AJW (x2)

AOW (x1)

1/2”(x2)

7/16”(x2)

9/16”(x2)

• DO NOT COMPLETELY TIGHTEN THE 5/16” NYLOCK

FLANGE NUTS IN THIS STEP! Only tighten the Nuts

until the Rim does not wobble. Tightening the Nuts

will adjust the Rim tension.

!

DFE (x4) AAA (x4)

AAA

DFE

AAA

AMY

• A Centerlock Nut

will require some effort

to thread onto a Bolt.

See page 2 for details.

3.4

18

7 5/8 in/po (≈19cm)

Metal Parts

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

4

(x2) (x2)

3/4" (≈19 mm) 9/16" (≈14 mm)

(x1)

BCR

AJY (x2)

AKC (x2)

AKB (x2)

AAX (x4)

ABB (x1)

AAD (x2)

GBU (x2)

DFC (x1)

7 1/16 in/po (≈18cm)

7 1/2 in/po (≈19cm)

7 1/2”

DGA (x2)

ABN (x8)

7 5/8 in/po (19.4 cm)

7 1/2 in (19 cm)

30 1/6 in (76.4 cm)

7 1/2 in/po (19 cm)

21 1/8 in (53.6 cm)

BACKBOARD-TO-POLE ASSEMBLY

19

 SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

4.1 • Attach the Short Extension Arms (AKC) to the Backboard Brackets in the location shown with the hardware indicated.

Secure only by hand at this point.

AKC

AAX ABN

ABN

DGA

AAX (x1)

ABN (x2)

DGA (x1)

3/4" (≈19 mm) (x2)

• DO NOT strike this Bolt (GBU) with a mallet!

If there is difﬁ culty sliding the Bolt into place,

use a wrench to turn the Bolt until it has

advanced into position.

!

• A Centerlock Nut requires

some effort to thread onto a

Bolt. See page 4 for details.

• If necessary, use a bolt to remove any

excess powder coating from the holes in the

Backboard Brackets.

!

GBU (x1)

GBU

7 5/8 in/po (≈19cm)

20

 SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

AKB AKB

AAX

ABB

DFC

DGA

GBU

AAX (x1)

DGA (x1)

9/16" (≈14 mm) (x2)

4.2 • Attach the ends of the Long Extension Arms (AKB) (that only have one hole)

to the Backboard Brackets in the location shown with the hardware

indicated. Secure only by hand at this point.

• Secure the Hex Bolt (DFC) to the

Backboard Brackets as shown.

4.3

ABB (x1)

DFC (x1)

7 1/2 in/po (≈19cm)

7 1/2”

7 1/2 in/po (19 cm)

3/4" (≈19 mm) (x2)

ABN (x2)

ABN

GBU (x1)

7 5/8 in/po (≈19cm)

7 5/8 in/po (19.4 cm)

La page charge ...

Lifetime 90599 Le manuel du propriétaire

Lifetime 90599 Le manuel du propriétaire

dans d''autres langues

Documents connexes