Fanvil V67 Guide d'installation

Catégorie
Téléphones IP
Taper
Guide d'installation
Quick Installation Guide
V1 02
V67
PN:CJBA100215C0
Screen icon
Packaging list
Keys features
Handset
Handset Cord
Stand Power Adapter
(Optional)
Ethernet Cable Quick Installation Guide
Navigation keys and OK key.
Long-press Up key to check the phone
common information (IP address/MAC
address/etc.)
IP Phone
Message waiting indicator
Phonebook key
Voice message key
Return key,go back to the previous directory
Home key, go back to Homepage
In idle mode or during ringing:
increase or decrease ringer volume
In communication: increase or
decrease earpiece, headset or hands-free volume
In idle mode: activate/deactivate silent mode
In communication mode: mute/un-mute a call
Headset key, activate/deactivate headset
Redial key, access to redial the last record
Hand-free key, activate/deactivate hands free
Wall Stand
(Buy separately)
In headset mode
In hands-free mode
In handset mode
Mute activated
Auto-answering activated
Call is on hold
Call Forward activated
Internet is connected Received call
Silent mode
Internet is disconnected
Dialed call
Missed call(s)
Forward call
Missed call(Status bar)
Do not disturb activated
New VM Messages
New SMS
Wireless network
connected
Wireless network
disconnected
Installation the device
Attach the stand and adjust the angle of the touch screen
Language setting
1. Press Phone Settings icon > Language & Input > Language.
2. Select the desired language.
Making a call
1. Pre-dialing: enter the phone number and pick up the
handset.
2. Direct dialing: lift the handset and enter the phone
number.
3. Handsfree: enter phone number and press or vice
versa.
4. Headset: enter phone number and press or vice versa.
5. Dial icon: Click dial icon and then enter the phone number.
6. Designated line: press line key, enter phone number and
press dial key.
Accepting a call
1. Using the handset: pick up the handset.
2. Using the headset: press .
3. Using the handsfree: press .
Configuration
Configuration via Phone
Configuration via Web
Connecting to the Device
Please connect power adapter, network, PC, handset, and
headset to the corresponding ports as described in below
picture.
①USB port: connect USB device (USB flash drive,USB Headset)
② Power port: connect the power adapter.
③ Network port: connecting local area network or internet.
④ PC port: the network port connect to the computer.
⑤ Headset port: connect headset.
⑥ Handset port: connect IP Phone handset.
Adjust shutter switch
Wall mounting (Wall stand need buy separately)
DC 12V
PUSH
1. Press Phone Settings icon.
2. Select Ethernet Settings: To configure the Network Settings
(DHCP/Static/PPPoE).
3. Select Line: To configure enable the account, input the
SIP server address, port, user name, password etc.
4. Save the configuration.
1. Get the IP address from the phone: Press Phone Settings icon
> Common Information.
2. Login: Input the IP address in the web browser. The PC and
phone should be in the same IP address segment (The default
username and password are both ‘admin’.)
3. Configure: Select network/account, etc. And fill the relevant
content.
4. Save the configuration.
Fanvil Technology Co., Ltd
Website: www.fanvil.com
Tel: +86-755-2640-2199 Fax: +86-755-2640-2618
Add: 10/F Block A, Dualshine Global Science Innovation Center,
Honglang North 2nd Road, Bao'an District, Shenzhen, China
Putting a call on hold
Call transfer
Attended transfer:
Blind transfer:
1. Press Transfer soft key during the active conversation,
the call is put on hold.
2. Dial the second telephone number.
3. When the call is answered, then press Transfer soft key to
complete the operation.
1. Press Transfer soft key during the active conversation,
the call will be held.
2. Then enter the 2nd telephone number and press Transfer
soft key.
1. Press Hold soft key, caller is put on hold.
2. To retrieve the call press Resume soft key.
Note: with more than one active call, select desired call by
sliding screen and use the corresponding soft key to hold
or resume.
Call forward
1. Press Phone Settings icon > Line > Select the line>
Forward Settings.
2. Enter the destination number and the type of forward.
Call conference
1. Once in line with 1st caller, press Conference key,
1st caller is put on hold.
2. Then call the 2nd number.
3. After, 2nd call is established, press Conference key to
set up the conference.
Call Mute
1. Press to Mute the microphone during the call.
2. Press again to un-mute the conversation.
Redial
1. Press , redial a call number.
Programmable keys
DSS keys :
Other keys :
1. You can configure shortcuts for the navigation keys and
softkeys on web UI.
2. You can press Phone setting icon > Key, select the
SoftkeyScreen you need, then select among the
configurable items, and select your desired type and
value, press icon.
1. You can use the phone web interface to configure the
keys of the screen.
2. You can press any keys which is blank or long-press the
key that configured, select a type and value, pressicon.
Call list
1. Press Call Log icon .
2.Scroll the list using navigation key or slide the screen.
Do not disturb
1. Press DND icon when standby or click Phone Settings
icon > DND.
2. Select the Mode.
Voice message
1. To access your voice mailbox, press Voice message key
or Voice message icon , number of message be indicated
if provided by your server or PBX.
2. Select the line and press phone icon to call.
Bluetooth
1. Press Bluetooth icon in the status bar to open Bluetooth.
2. Press Settings icon > Bluetooth to enter the Bluetooth
Interface.
After opening, it displays the scanned Bluetooth list, select any
device, and click on the device pairing.
WiFi
1. Press WiFi icon in the status bar to open WiFi.
2. Press Settings icon > Wi-Fi to enter the WiFi configuration
Interface.
3. After opening, it displays the available WiFi list.
4. Select the WiFi you want to connect
5. Enter the appropriate password to connect to the WiFi.
The default is DHCP mode.
Phonebook
Access phonebook:
Add new entry:
1. Press Contact icon, Press All Contacts or other group >
Press Add icon.
2. Enter name and number and press OK icon.
1. Press Contact icon.
2. Select All Contacts or other group.
3. To dial an entry, press Dial icon .
Regulatory Compliance
Federal Communication Commission (FCC) — USA
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received; including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Any changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this
equipment is a label that contains, among other information, a product identifier in the format US: 3I1IPNANV67.
If requested, this number must be provided to the telephone company.
Industry Canada Equipment Standard for Digital Equip-ment (ICES) — Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development (ISED) — Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de
rayonnement et votre corps
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with IC multi-transmitter product procedures.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou
transmetteur.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Le présent produit est conforme aux spécifications techniques applicables d’Innovation, Sciences et Développement
économique Canada.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Fanvil V67 Guide d'installation

Catégorie
Téléphones IP
Taper
Guide d'installation

dans d''autres langues