JVC KD-T92MBS Mode d'emploi

Taper
Mode d'emploi
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
FRANÇAIS
ESPAÑOL
B5K-0863-00 [K]
CD RECEIVER
Quick Start Guide
RÉCEPTEUR CD
Guide de démarrage rapide
RECEPTOR CON CD
Guía de inicio rápido
KD-T92MBS / KD-T721BT / KD-TD72BT / KD-SR87BT
For detailed operations and information, refer to the INSTRUCTION MANUAL on the following
website:
Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur
le site web suivant:
Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE
INSTRUCCIONES en el siguiente sitio web:
<https://www.jvc.net/cs/car/>
For customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
KD_T92MBS_K_B5K-0863-00_Cover_4th Draft.indd 1KD_T92MBS_K_B5K-0863-00_Cover_4th Draft.indd 1 2/7/2021 5:18:40 PM2/7/2021 5:18:40 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
i
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product
relating to laser product safety.
JVCKENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR
SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida
útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de
residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser
desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final
de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento
adecuado a estos productos y a sus subproductos residuales correspondientes.
Póngase en contacto con su administración local para obtener información sobre el
punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación
de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos
perjudiciales en la salud y el medio ambiente.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou
entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao
mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
Supplier's Declaration of Conformity
Trade Name: JVC
Products: CD RECEIVER
Model Name: KD-T92MBS/KD-T721BT/KD-TD72BT/KD-SR87BT
Responsible Party: JVCKENWOOD USA CORPORATION
2201 East Dominguez Street, Long Beach, CA 90810, U.S.A.
PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
JS_JVC_QSG_KD_T92MBS_K_C00.indd iJS_JVC_QSG_KD_T92MBS_K_C00.indd i 16/2/2021 1:20:12 PM16/2/2021 1:20:12 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ii
Para cumplimiento de la IFT:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada”
Contains Bluetooth Module FCC ID: ZWY88112
IC ID: 12033A-88112
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
SOFTWARE LICENSE AGREEMENT
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is
copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions
which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the
Product in which the "Licensed Software" is embedded.
The Licensed Software may include the software which has been licensed to the Licensor directly or
indirectly from any third party. In such case, some third parties require the Users to follow their conditions
for use separately from this Software License Agreement. Such software shall not be subject to this
Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided
separately below.
Article 1 General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case
referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.
(the country where the User bought the Product (hereinafter the "Country")
Article 2 License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the
Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed
Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall
not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation
manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright
Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 3 Conditions for Grant of License
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software
embedded in the Product (including any related materials, updates and upgrades) on condition that
no original, copies or related materials continue in the possession of the User, and that the User shall
cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code
analysis works in connection with the Licensed Software.
ISED Caution
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Attention de ‘ISED
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage.
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
CAUTION
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio
frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at
least 20 cm or more away from person’s body.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices
d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’ISED. Cet équipement
doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps
humain.
JS_JVC_QSG_KD_T92MBS_K_C00.indd iiJS_JVC_QSG_KD_T92MBS_K_C00.indd ii 16/2/2021 1:20:12 PM16/2/2021 1:20:12 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iii
Article 4 Right pertaining to the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents
shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or
sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be
entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any
related documents.
Article 5 Indemnification of Licensor
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User
or any third party due to the exercise of the license granted to the User under this Agreement, unless
otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with
certain objective of the Licensed Software.
Article 6 Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any
other intellectual property right that was caused by the User's use of the Licensed Software, the User shall
settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any
inconvenience it may cause.
Article 7 Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof
or any other information to be granted under this Agreement, as well as the conditions of this Agreement
as has not yet entered the public domain, and shall not disclose or divulge the same to any third party
without approval of the Licensor.
Article 8 Termination
In case the User falls under any of the events described in the following items, the Licensor may
immediately terminate this Agreement or claim that the User compensates for the damage incurred by the
Licensor due to such event:
(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment, provisional attachment,
provisional disposition or any other compulsory execution.
Article 9 Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed
Software, any related documents and copies thereof within two (2) weeks from such date of termination.
Article 10 Protection of Copyright
1. The copyright and all the other intellectual property rights relating to the Licensed Software
shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the
ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the
copyright and other intellectual property rights.
Article 11 Export Restriction
1. It is prohibited to export the Licensed Software and any related documents outside the country
of the User (including transmission thereof outside the country of the User via Internet of other
communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions
adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and
domestic laws (including the export control regulation of the country of User and any other countries,
and any restrictions concerning the end-users, the use by end-users and importing countries to be
provided by the country of User and any other countries, and any other governmental authorities).
Article 12 Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions
shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of
this Agreement shall be provided or settled upon good-faith consultation between the Licensor and
the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and
any dispute arising from, and relating to the rights and obligations under, this Agreement shall be
submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.
JS_JVC_QSG_KD_T92MBS_K_C00.indd iiiJS_JVC_QSG_KD_T92MBS_K_C00.indd iii 16/2/2021 1:20:12 PM16/2/2021 1:20:12 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iv
Important Notice concerning the Software
-jansson
Copyright (c) 2009-2012 Petri Lehtinen <[email protected]>
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
-cJSON
Copyright (c) 2009 Dave Gamble
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
-CMP
The MIT License (MIT)
Copyright (c) 2014 Charles Gunyon
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
nanopb
Copyright (c) 2011 Petteri Aimonen <jpa at nanopb.mail.kapsi.fi>
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be
held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications,
and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote
the original software. If you use this software in a product, an acknowledgment in the product
documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the
original software.
3. This notice may not be removed or altered from any source distribution.
JS_JVC_QSG_KD_T92MBS_K_C00.indd ivJS_JVC_QSG_KD_T92MBS_K_C00.indd iv 16/2/2021 1:20:13 PM16/2/2021 1:20:13 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
v
sha2
AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/
Copyright (c) 2000-2001, Aaron D. Gifford
All rights reserved.
You may obtain a copy of the license at
https://opensource.org/licenses/BSD-3-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Posix
Copyright (c) 1990, 1993
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following
acknowledgement:
This product includes software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or
promote products derived from this software without specific prior written permission.
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business.
Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is
preserved.
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
License to copy and use this software is granted provided that it is identified as the “RSA Data Security, Inc.
MD4 Message-Digest Algorithm” in all material mentioning or referencing this software or this function.
Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved.
Author: Chris G. Demetriou
Permission to use, copy, modify and distribute this software and its documentation is hereby granted,
provided that both the copyright notice and this permission notice appear in all copies of the software,
derivative works or modified versions, and any portions thereof, and that both notices appear in supporting
documentation.
CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS “AS IS” CONDITION. CARNEGIE MELLON
DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF
THIS SOFTWARE.
Carnegie Mellon requests users of this software to return to
Software Distribution Coordinator or Software.Distribution@
CS.CMU.EDU
School of Computer Science
Carnegie Mellon University
Pittsburgh PA 15213-3890
any improvements or extensions that they make and grant Carnegie the rights to redistribute these
changes.
License is also granted to make and use derivative works provided that such works are identified as
“derived from the RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or
referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or
the suitability of this software for any particular purpose. It is provided “as is” without express or implied
warranty of any kind.
Copyright (c) 1993 Martin Birgmeier
All rights reserved.
You may redistribute unmodified or modified versions of this source code provided that the above
copyright notice and this and the following conditions are retained.
This software is provided “as is”, and comes with no warranties of any kind. I shall in no event be liable for
anything that happens to anyone/anything when using this software.
These notices must be retained in any copies of any part of this documentation and/or software.
JS_JVC_QSG_KD_T92MBS_K_C00.indd vJS_JVC_QSG_KD_T92MBS_K_C00.indd v 16/2/2021 1:20:13 PM16/2/2021 1:20:13 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
vi
T-Kernel 2.0
This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum
(www.tron.org)
BSD-3-Clause
Copyright (c) 2000-2001, Aaron D. Gifford
All rights reserved.
You may obtain a copy of the license at
https://opensource.org/licenses/BSD-3-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
LFS Subsystem
Copyright The Regents of the University of California. All rights reserved.
You may obtain a copy of the license at
https://directory.fsf.org/wiki/License:BSD-4-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Accordo2 Player
Apache License
Licensed under the Apache License,
Version 2.0, January 2004(the “License”);
You may obtain a copy of the license at
http://www.apache.org/licenses/LICENSE-2.0
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
JS_JVC_QSG_KD_T92MBS_K_C00.indd viJS_JVC_QSG_KD_T92MBS_K_C00.indd vi 16/2/2021 1:20:13 PM16/2/2021 1:20:13 PM
2
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Basic procedure
1 Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2 Connect the wires properly. See “Wiring connection” on page 3.
3 Install the unit to your car. See the following “Installing the unit
(in-dash mounting)”.
4 Connect the terminal of the car battery.
5 Press B SRC to turn on the power.
6 Detach the faceplate and reset the unit within 5 seconds. See “How to
reset” on page 4.
Installing the unit (in-dash mounting)
Installation/Connection
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
WARNING
The unit can only be used with a 12 V DC power supply, negative ground.
Disconnect the battery’s negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to
prevent a short circuit.
To prevent short circuit:
Insulate unconnected wires with vinyl tape.
Be sure to ground this unit to the car’s chassis again after installation.
Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into contact with
metal parts to protect the wires.
CAUTION
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly
after use of the unit. Metal parts such as the heat sink and enclosure become hot.
Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in
parallel.
Connect speakers with a maximum power of more than 50 W. If the maximum power of the speakers is
lower than 50 W, change the
[AMPGAIN]
setting to avoid damaging the speakers.
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the
terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the
ignition key.
Keep all cables away from heat dissipate metal parts.
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working
properly.
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with
one that has the same rating.
Hook on the top side
Bend the appropriate tabs to hold the
sleeve firmly in place.
Dashboard of your car
KD_T92MBS_K_B5K-0863-00_EN_4th Draft.indd 2KD_T92MBS_K_B5K-0863-00_EN_4th Draft.indd 2 2/7/2021 5:34:12 PM2/7/2021 5:34:12 PM
3
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Wiring connection
a Light blue/yellow: To the
steering wheel remote control
adapter
b Brown (not used)
c Blue: To power antenna
d Blue/white: To amplifier
e Blue/white: Remote
(12 V 350mA)
f Orange/white: Illumination
g Yellow: Battery 12V
h Red: Ignition 12V
i Black: Ground
j Gray ª, Gray/black ·:
Front speaker (right)
k White ª, White/black ·:
Front speaker (left)
l Purple ª, Purple/black ·:
Rear speaker (right)
m Green ª, Green/black ·:
Rear speaker (left)
Removing the unit
Installing the unit (without mounting sleeve)
1 Remove the mounting sleeve and trim plate from the unit.
2 Align the holes in the unit (on both sides) with the vehicle
mounting bracket and secure the unit with screws (commercially
available).
Part list (supplied)
(A) Faceplate (×1)
(B) Trimplate (×1)
(C) Mounting sleeve (×1)
(D) Wiring harness (×1)
(E) Extraction key (×2)
Use only the specified screws.
Using wrong screws might damage
the unit.
Join the same color
wires together.
Custom wiring harness
(separately purchased)
Vehicle dashboard
Recommended connection
Factory wiring
harness (vehicle)
Antenna terminal
Fuse (10 A)
JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 3JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 3 16/2/2021 1:36:22 PM16/2/2021 1:36:22 PM
4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Basics (on faceplate)
KD-T721BT/
KD-TD72BT/
KD-SR87BT
Volume knob Loading slot
USB input
terminal
Detach button
Display window*1
Auxiliary
input jack
Attach Detach How to reset
Reset the unit
within 5seconds
after detaching the
faceplate.
To On the faceplate
Turn on the power Press B SRC.
Press and hold to turn off the power.
Adjust the volume Turn the volume knob.
Select a source Press B SRC repeatedly.
Change the display information*2 Press repeatedly.
*2 One of the display information supports Music Synchronization Effect. The illumination color or brightness level of
the buttons changes and synchronizes with the music level.
Before Use
IMPORTANT
To ensure proper use, please read through this Guide before using
this product. It is especially important that you read and observe
Warnings and Cautions in this Guide.
Please keep the Guide in a safe and accessible place for future
reference.
WARNING
Do not operate any function that takes your attention away from safe
driving.
CAUTION
Volume setting:
Adjust the volume so that you can hear sounds outside the car to
prevent accidents.
Lower the volume before playing digital sources to avoid
damaging the speakers by the sudden increase of the output level.
General:
Avoid using the external device if it might hinder safe driving.
Make sure all important data has been backed up. We shall bear no
responsibility for any loss of recorded data.
Never put or leave any metallic objects (such as coins or metal
tools) inside the unit to prevent a short circuit.
If a disc error occurs due to condensation on the laser lens, eject
the disc and wait for the moisture to evaporate.
Depending on the types of cars, the antenna will automatically
extend when you turn on the unit with the antenna control wire
connected. Turn off the unit when parking at a low ceiling area.
*1 Only for illustration purpose.
JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 4JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 4 16/2/2021 1:36:22 PM16/2/2021 1:36:22 PM
5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Getting Started
1 Acknowledge the crossover type and cancel the
demonstration
When you turn on the power for the first time (or
[FACTORY RESET]
is set to
[YES]
), the display shows: “2-WAY X’OVER” or “3-WAY X’OVER” “PRESS”
“VOLUME KNOB” “TO CONFIRM”.
1 Press the volume knob to acknowledge the current crossover type.
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”
2 Press the volume knob.
[YES]
is selected for the initial setup.
3 Press the volume knob again.
“DEMO OFF” appears.
2 Set the clock and date
1 Press and hold .
2 Turn the volume knob to select
[CLOCK]
, then press the knob.
To adjust the clock
3 Turn the volume knob to select
[CLOCKADJUST]
, then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Set the time in the order of “Hour” “Minute”.
5 Turn the volume knob to select
[CLOCK FORMAT]
, then press the knob.
6 Turn the volume knob to select
[12H] or [24H]
, then press the knob.
To set the date
7 Turn the volume knob to select
[DATESET]
, then press the knob.
8 Turn the volume knob to make the settings, then press the knob.
Set the date in the order of “Day” “Month” “Year”.
9 Press to exit.
To return to the previous setting item, press .
3 Set the basic settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[SYSTEM]
[KEY BEEP] (Not applicable when 3-way crossover is selected.)
[ON]: Activates the keypress tone. ; [OFF]: Deactivates.
[FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ;
[NO]: Cancels.
[CLOCK]
[CLOCK DISPLAY] [ON]: The clock time is shown on the display even when the unit is
turned off. ; [OFF]: Cancels.
[ENGLISH] Select the display language for menu and music information if
applicable.
By default, [ENGLISH] is selected.
[ESPANOL]
[FRANCAIS]
JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 5JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 5 16/2/2021 1:36:23 PM16/2/2021 1:36:23 PM
6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Radio
Search for a station
1 Press B SRC repeatedly to select FM or AM.
2 Press S / T to search for a station automatically.
(or)
Press and hold S / T until “M” flashes, then press repeatedly to
search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1 to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
“MEMORY” appears once the station is stored.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press .
2 Turn the volume knob to select a preset number, then press the knob.
CD/USB/iPod
Selectable source:
CD/USB/iPodUSB or iPodBT
Start playback
The source changes automatically and playback starts when you load a disc
or attach a device (USB device/ iPod/iPhone) to the USB input terminal.
To On the faceplate
Reverse/Fast-forward Press and hold S / T.
Select a track/file Press S / T.
Select a folder Press 2 J / 1 K.
Repeat play Press 4 repeatedly.
Random play Press 3 repeatedly.
JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 6JS_JVC_QSG_KD_T92MBS_K_EN_1.indd 6 16/2/2021 1:36:23 PM16/2/2021 1:36:23 PM
7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Menu Settings
1 Press and hold to enter menu settings.
2 Turn the volume knob to select an item, then press the knob.
3 Repeat step 2 until the desired item is selected/activated.
4 Press to exit.
To return to the previous setting item, press .
Refer to the INSTRUCTION MANUAL on the following website for the
detailed explanation of each item: <https://www.jvc.net/cs/car/>
The availability of each item vary depending on the model.
Menu items
[EQ SETTING]
: Selects a preset equalizer or adjusts your own sound
settings.
[AUDIO CONTROL]
: Sets your preferred audio settings.
[SOUND EFFECT]
: Sets your preferred sound effect.
[DISPLAY]
: Sets your preferred control for the display window.
[COLOR]
: Sets your preferred illumination color for buttons.
[TUNER SETTING]
: Settings for radio source.
[SIRIUS XM]
: Settings for Sirius XM tuner.
[BT MODE]
: Settings for using a Bluetooth device.
[REMOTE APP]
: Settings for using smartphone to control this unit.
[MIC GAIN]
* : Sets the sensitivity of the microphone.
[NR LEVEL]
* : Adjusts the noise reduction level.
[ECHO CANCEL]
* : Adjusts the echo cancellation delay time.
[SYSTEM]
: Settings for this unit.
[CLOCK]
: Adjusts the clock.
[ENGLISH]
: Selects language for the menu and music information.
[ESPANOL]
: Selects language for the menu and music information.
[FRANCAIS]
: Selects language for the menu and music information.
[DEMO MODE]
: Activates or deactivates the display demonstration.
* Applicable only while talking on the phone.
Examples of some well-used settings
Subwoofer Level Setting
1 Press and hold to enter menu settings.
2 Turn the volume knob clockwise to select
[AUDIO CONTROL]
, then press
the knob.
3 Turn the volume knob clockwise to select
[SUBWOOFER SET]
, then press
the knob.
4 Turn the volume knob clockwise to select
[ON]
, then press the knob.
5 Turn the volume knob clockwise to select
[SUB.W LEVEL]
, then press the
knob.
6 Press the volume knob if
[PRE-OUT]
is shown on the display.
7
Turn the volume knob to adjust the subwoofer level, then press the knob.
Continued on the next page...
KD_T92MBS_K_B5K-0863-00_EN_4th Draft.indd 7KD_T92MBS_K_B5K-0863-00_EN_4th Draft.indd 7 2/7/2021 5:34:40 PM2/7/2021 5:34:40 PM
8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
5 Turn the volume knob to choose a color, then press the knob.
[COLOR01]
to
[COLOR49]
[USER]
: The color you have created for
[DAYCOLOR]
or
[NIGHTCOLOR]
is shown.
[COLORFLOW01]
to
[COLORFLOW03]
: Color changes at
different speeds.
[CRYSTAL]
/
[FLOWER]
/
[FOREST]
/
[GRADATION]
/
[OCEAN]
/
[RELAX]
/
[SUNSET]
: The selected color pattern is
shown. (Selectable only when
[ALLZONE]
is selected
in step4.)
6 Repeat step 4 and step 5 to set color for other zones.
7 Press to exit.
Other Information
For playback operations of AUX and SiriusXM® Radio sources, refer to the
INSTRUCTION MANUAL on the following website:
<https://www.jvc.net/cs/car/>
The availability of each source vary depending on the model.
Note for specifications
Bluetooth Frequency Range:
2.402 GHz — 2.480 GHz
Bluetooth RF Output Power (E.I.R.P.):
+4 dBm (MAX), Power Class 2
Speaker Impedance:
4Ω—8Ω
Operating Voltage:
12 V DC car battery
8 Press to exit the setting menu.
Note:
For KD-T721BT/KD-TD72BT/KD-SR87BT, you need to set
[SPK/PRE OUT]
to
[REAR/SUB.W]
or
[SUB.W/SUB.W]
before you can make the subwoofer level
settings.
Illumination Color Setting
For KD-T92MBS, you can set your preferred illumination color for each zone.
1 Press and hold to enter menu settings.
2 Turn the volume knob clockwise to select
[COLOR]
, then press the knob.
3 Press the volume knob if
[PRESET]
is shown on the display.
4 Turn the volume knob to choose a zone (
[ALL ZONE]
,
[ZONE 1]
,
[ZONE 2]
),
then press the knob.
KD_T92MBS_K_B5K-0863-00_EN_4th Draft.indd 8KD_T92MBS_K_B5K-0863-00_EN_4th Draft.indd 8 2/7/2021 5:34:56 PM2/7/2021 5:34:56 PM
9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Bluetooth®
Depending on the Bluetooth version, operating system and the
firmware version of your mobile phone, Bluetooth features may not
work with this unit.
Be sure to turn on the Bluetooth function of the device to make the
following operations.
Signal conditions vary depending on the surroundings.
Connect the microphone
Connect the supplied microphone to the microphone input jack on the rear
panel.
Adjust the
microphone
angle
Secure using cord
clamps (not supplied)
if necessary.
Pair and connect a Bluetooth device for the first time
1 Press B SRC to turn on the unit.
2 Search and select the name of your receiver (“KD-T92MBS”/
“KD-T721BT”/“KD-TD72BT”/“KD-SR87BT”) on the Bluetooth device.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps
described below.
(A) “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device
are the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL–YES” “BACK–NO”
Press the volume knob to start pairing.
If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code
“0000” into the Bluetooth device.
If only “PAIRING” appears, operate the Bluetooth device to confirm
pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light
up when the Bluetooth connection is established.
Answer a call
Press or the volume knob.
To adjust the phone volume
[00]
to
[35]
, turn the volume knob.
To end a call, press and hold or the volume knob.
Audio player via Bluetooth
1 Press B SRC repeatedly to select BTAUDIO.
Pressing enters BT AUDIO directly.
2 Operate the audio player via Bluetooth to start playback.
To On the faceplate
Play back/pause Press the volume knob.
Select group or folder Press 2 J / 1 K.
Reverse skip/Forward skip Press S / T.
Reverse/Fast-forward Press and hold S / T.
Repeat play Press 4 repeatedly.
Random play Press 3 repeatedly.
JS_JVC_QSG_KD_T92MBS_K_EN_2.indd 9JS_JVC_QSG_KD_T92MBS_K_EN_2.indd 9 11/3/2021 9:30:46 AM11/3/2021 9:30:46 AM
2
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Procédure de base
1 Retirez la clé de contact, puis déconnectez la borne de la batterie de la
voiture.
2 Connectez les fils correctement. Voir “Connexions à la page3.
3 Installez l’appareil dans votre voiture. Reportez-vous à “Installation de
l’appareil (montage encastré)” ci-après.
4 Connectez la borne de la batterie de la voiture.
5 Appuyez sur B SRC pour mettre l’appareil sous tension.
6 Détachez la façade et réinitialisez l’appareil avant 5 secondes. Voir
“Comment réinitialiser” à la page4.
Installation de l’appareil (montage encastré)
Installation/Connexion
Cette section est réservée aux installateurs professionnels.
Pour des raison de sécurité, laissez le travail de câblage et de montage des professionnels. Consultez
votre revendeur autoradio.
MISE EN GARDE
L’appareil peut uniquement être utilisé avec une alimentation de 12 V CC, à masse négative.
Déconnectez la borne négative de la batterie avant le câblage et le montage.
Ne connectez pas le fil de batterie (jaune) et le fil d’allumage (rouge) au châssis de la voiture ou au fil de masse
(noir) pour éviter les courts-circuits.
Pour éviter les courts-circuits:
Isolez les fils non connectés avec du ruban adhésif.
Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après
l’installation.
Fixez les câbles avec des serre-câbles et enrouler un ruban de vinyle autour des câbles qui entrent en contact
avec des pièces métalliques pour protéger les câbles.
AVERTISSEMENT
Installez cet appareil dans la console de votre véhicule. Ne touchez pas les parties métalliques de cet appareil
pendant ou juste après son utilisation. Les parties métalliques, comme le dissipateur de chaleur et le boîtier,
deviennent chaudes.
Ne connectez pas les fils des l’enceintes au châssis de la voiture, au fil de masse (noir) ou en parallèle.
Connectez des enceintes avec une puissance maximum de plus de 50 W. Si la puissance maximum des enceintes
est inférieure à 50W, changez le réglage
[AMPGAIN]
pour éviter d’endommager les enceintes.
Montez l’appareil avec un angle de moins de 30º.
Si le faisceau de fils de votre véhicule ne possède pas de borne d’allumage, connectez le fil d’allumage (rouge) à la
borne du boîtier de fusible de votre véhicule qui offre une alimentation de 12 V CC et qui se met en et hors service
avec la clé de contact.
Gardez tous les câbles à l’écart des dissipateurs thermiques.
Après avoir installé l’appareil, vérifiez si les lampes de frein, les indicateurs, les clignotants, les essuie-glaces, etc.
de la voiture fonctionnent correctement.
Si un fusible saute, assurez-vous d’abord que les câbles ne touches pas le châssis de la voiture puis remplacez le
vieux fusible par un nouveau de même valeur.
Crochet sur le
côté supérieur
Tordez les languettes appropriées pour
maintenir le manchon en place.
Tableau de bord de votre voiture
KD_T92MBS_K_B5K-0863-00_FR.indd 2KD_T92MBS_K_B5K-0863-00_FR.indd 2 26/7/2021 9:06:37 AM26/7/2021 9:06:37 AM
3
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Connexions
a Bleu clair/jaune: À l’adaptateur
de télécommande volant
b Marron (non utilisé)
c Bleu: À l’antenne alimentée
d Bleu/blanc: À l’amplificateur
e Bleu/blanc: Télécommande
(12 V 350mA)
f Orange/blanc: Éclairage
g Jaune: Batterie 12 V
h Rouge: Allumage 12V
i Noir: Masse
j Gris ª, Gris/noir ·:
Enceinte avant (droite)
k Blanc ª, Blanc/noir ·:
Enceinte avant (gauche)
l Violet ª, Violet/noir ·:
Enceinte arrière (droite)
m Vert ª, Vert/noir ·:
Enceinte arrière (gauche)
Retrait de l’appareil
Installation de l’appareil (sans le manchon de montage)
1 Retirez le manchon de montage et la plaque de garniture de l’appareil.
2 Alignez les entailles de l’appareil (des deux côtés) avec le support de
montage du véhicule et fixez l’appareil avec les vis (en vente dans le
commerce).
Liste de pièces (fourni)
(A) Façade (×1)
(B) Plaque de garniture (×1)
(C) Manchon de montage (×1)
(D) Faisceau de fils (×1)
(E) Clé d’extraction (×2)
N’utiliser que les vis spécifiés.
L’utilisation de vis incorrects peut
endommager l’appareil.
Joignez les fils de même
couleur ensemble.
Faisceau de fils personnalisé
(vendu séparément)
Tableau de bord
du véhicule
Connexion recommandée
Faisceau de câbles
de l’usine (véhicule)
Borne de l’antenne
Fusible (10 A)
KD_T92MBS_K_B5K-0863-00_FR.indd 3KD_T92MBS_K_B5K-0863-00_FR.indd 3 26/7/2021 9:06:37 AM26/7/2021 9:06:37 AM
4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Fonctionnement de base (sur la façade)
KD-T721BT/
KD-TD72BT/
KD-SR87BT
Bouton de volume Fente d’insertion
Prise d’entrée
USB
Touche de détachement
Fenêtre d’affichage*1
Prise d’entrée
auxiliaire
Attachez Détachez Comment réinitialiser
Réinitialisez l’appareil en
moins de 5 secondes
après avoir détaché la
façade.
Pour Sur la façade
Mettez l’appareil sous tension Appuyez sur B SRC.
Maintenez la touche enfoncée pour mettre
l’appareil hors tension.
Ajustez le volume Tournez le bouton de volume.
Sélectionner la source Appuyez répétitivement sur B SRC.
Changez l’information sur
l’affichage*2 Appuyez répétitivement sur .
*2 Une des informations de l’affichage prend en charge l’effet de synchronisation musicale. La couleur d’éclairage ou le niveau
de luminosité des touches change et est synchronisé avec le niveau de la musique.
Avant l’utilisation
IMPORTANTES
Pour utiliser correctement l’appareil, veuillez lire ce Guide complément
avant de l’utiliser. Il est particulièrement important que vous lisiez et
acceptiez les avertissements et les précautions de ce Guide.
Veuillez garder ce Guide dans un endroit sûr et accessible pour une
utilisation future.
MISE EN GARDE
N’utilisez aucune fonction qui risque de vous distraire de la conduite sure
de votre véhicule.
AVERTISSEMENT
Réglage du volume:
Ajustez le volume de façon à pouvoir entendre les sons extérieurs à la
voiture afin d’éviter tout risque d’accident.
Réduisez le volume avant de reproduire des sources numériques afin
d’éviter d’endommager les enceintes par la soudaine augmentation du
niveau de sortie.
Généralités:
Éviter d’utiliser le périphérique extérieur s’il peut gêner une conduite en
toute sécurité.
Assurez-vous que toutes les données importantes ont été sauvegardées.
Nous ne pouvons pas être tenu responsable pour toute perte des
données enregistrées.
Veuillez faire en sorte de ne jamais mettre ou laisser d’objets métalliques
(tels que des pièces ou des outils) dans l’appareil, afin d’éviter tout
risque de court-circuit.
Si une erreur de disque se produit à cause de la condensation sur
l’objectif laser, éjectez le disque et attendez que l’humidité s’évapore.
En fonction du type de voiture, l’antenne s’étendra automatiquement
quand vous mettrez l’appareil sous tension si le câble de commande
d’antenne est connecté. Mettez l’appareil hors tension quand vous vous
garez dans un parking avec un plafond bas.
*1 Uniquement à des fins d’illustration.
KD_T92MBS_K_B5K-0863-00_FR.indd 4KD_T92MBS_K_B5K-0863-00_FR.indd 4 26/7/2021 9:06:37 AM26/7/2021 9:06:37 AM
5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Prise en main
1 Vérifiez le type de transition et annulez la
démonstration
Quand vous mettez l’appareil sous tension pour la première fois (ou que
[FACTORYRESET]
est réglé sur
[YES]
), l’affichage montre: “2-WAY X’OVER” ou
“3-WAYX’OVER” “PRESS” VOLUME KNOB” “TO CONFIRM”.
1 Appuyez sur le bouton de volume pour valider le type de transition actuel.
Puis, l’affichage montre: “CANCEL DEMO” “PRESS” VOLUME KNOB”
2 Appuyez sur le bouton de volume.
[YES]
est choisi pour le réglage initial.
3 Appuyez de nouveau sur le bouton de volume.
“DEMO OFF” apparaît.
2 Réglez l’horloge et la date
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour choisir
[CLOCK]
, puis appuyez sur le
bouton.
Pour ajuster l’horloge
3 Tournez le bouton de volume pour choisir
[CLOCKADJUST]
, puis appuyez sur
le bouton.
4 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le
bouton.
Réglez l’heure dans l’ordre “Heures” “Minutes”.
5 Tournez le bouton de volume pour choisir
[CLOCK FORMAT]
, puis appuyez sur
le bouton.
6 Tournez le bouton de volume pour choisir
[12H] ou [24H]
, puis appuyez sur
le bouton.
Pour régler la date
7 Tournez le bouton de volume pour choisir
[DATESET]
, puis appuyez sur le
bouton.
8 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le
bouton.
Réglez la date dans l’ordre Jour “Mois” Année.
9 Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur .
3 Faites les réglages de base
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour sélectionner un élément (voir le tableau
suivant), puis appuyez sur le bouton.
3 Répétez l’étape 2 jusqu’à ce que l’élément souhaité soit sélectionné ou
activé.
4 Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur .
Défaut: [XX]
[SYSTEM]
[KEY BEEP] (Non applicable quand la transition 3 voies est sélectionnée.)
[ON]:Met en service la tonalité des touches.; [OFF]:Met hors service la
fonction.
[FACTORY RESET] [YES]:Réinitialise les réglages aux valeurs par défaut (sauf la station
mémorisée).; [NO]:Annulation.
[CLOCK]
[CLOCK DISPLAY] [ON]:L’horloge apparaît sur l’affichage même quand l’appareil est hors
tension.; [OFF]:Annulation.
[ENGLISH] Sélectionnez la langue d’affichage pour le menu et l’information sur le
morceau si elle est disponible.
Par défaut, [ENGLISH] est sélectionné.
[ESPANOL]
[FRANCAIS]
KD_T92MBS_K_B5K-0863-00_FR.indd 5KD_T92MBS_K_B5K-0863-00_FR.indd 5 26/7/2021 9:06:38 AM26/7/2021 9:06:38 AM
6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Radio
Recherchez une station
1 Appuyez répétitivemenent sur B SRC pour sélectionner FM ou AM.
2 Appuyez sur S / T pour rechercher une station automatiquement.
(ou)
Maintenez en enfoncé S / T jusqu’à ce que “M” clignote, puis appuyez
répétitivement dessus pour rechercher une station manuellement.
Réglages en mémoire
Vous pouvez mémoriser un maximum de 18 stations pour FM et de 6 stations
pour AM.
Mémorisez une station
Pendant l’écoute d’une station....
Maintenez enfoncée une des touches numériques (1 à 6).
(ou)
1 Maintenez enfoncé le bouton de volume jusqu’à ce que “PRESETMODE”
clignote.
2 Tournez le bouton de volume pour choisir un numéro de préréglage, puis
appuyez sur le bouton.
“MEMORY apparaît une fois que la station est mémorisée.
Sélectionnez une station mémorisée
Appuyez sur l’une des touches numériques (1 à 6).
(ou)
1 Appuyez sur .
2 Tournez le bouton de volume pour choisir un numéro de préréglage, puis
appuyez sur le bouton.
CD/USB/iPod
Source sélectionnable:
CD/USB/iPod USB ou iPod BT
Démarrez la lecture
La source change automatiquement et la lecture démarre quand vous insérez un
disque ou connectez un périphérique (périphérique USB/ iPod/iPhone) à la prise
d’entrée USB.
Pour Sur la façade
Recherche rapide vers
l’arrière/vers l’avant Maintenez enfoncée S / T.
Sélectionnez une plage ou
un fichier Appuyez sur S / T.
Sélectionnez un dossier Appuyez sur 2
J / 1 K.
Lecture répétée Appuyez répétitivement sur 4
.
Lecture aléatoire Appuyez répétitivement sur 3
.
KD_T92MBS_K_B5K-0863-00_FR.indd 6KD_T92MBS_K_B5K-0863-00_FR.indd 6 26/7/2021 9:06:38 AM26/7/2021 9:06:38 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

JVC KD-T92MBS Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues