Galaxy Nightlight Projector
User Manual
Thank you for purchasing our products, please read the instruction manual
carefully before use. Instruction manual contains necessary safety advice and user
instructions, follow the instruction manual to operate in order to avoid damaging
the product for misuse. Check whether the product is damaged or not when you
receive the product.
Unboxing Check
Galaxy Projector x 1
Remote controller x 1
USB cable x 1
User manual x 1
1. Indoor use, projecting in the sky direction.
2. How to use the light projector, as shown below.
3. Connect Bluetooth “BTK10” of the smart phone to play music.
4. Use correct method of the remote control to make sure the remote control
is pointing at the infrared sensor.
1.Strictly in accordance with the instructions of this operation, do not disassemble
the host and accessories.
2.This product is suitable for indoor use.
3.The product is projected by LED and laser combinations, please do not use laser
shone directly in eyes and keep away from children.
The power requirement of this product is USB DC
5V/2A. Once the range exceeded, please use the
regulator device, otherwise it’ ll aect its service
life.
Pacakage list
Notice:
How to use:
Warnings
EN
1
1
2
2
3
4
5
6
7
8
1
4
5673
8
EN
Host button function description
Statement
Remote control function description
Instruction:
Automatic recognition USB data. Note that this projector can auto recognize
and play music while inserting USB memory. USB should contain some songs
l. Ocean wave 3 levels brightness adjustment
DC Input: 5V/2A.
Short press plays previous song; Long press reduce volume
Short press plays next song; Long press increase volume
Short press control music Play/pause; Long press change USB to Bluetooth (
Connect Bluetooth and U-Disk at same time, it’ll recognize U-Disk music for
priority)
Short press achieves Bluetooth/USB mode switch when connect Bluetooth and
USB at same time
This product has been comprehensive and rigorous tasted at the factory, the user
should strictly follow the warning and instructions. Improper use resulting in
product damage is not covered by the Company’s warranty.
When projector light connects power; LED blue light keeps on and in non-moved
status; laser light enters gradation mode; it can default automatically switch o in 4
hours.
Power ON/OFF
ll. When power on, LED light and laser light keep on; short press this key control
LED light switch, long press control laser light switch
2
EN
(Note: Four color RGBW buttons can be combined by two to form a double-color
projection)
3
1
2
3
4
5
6
7
8
9
10
11
12
13
Press “R” , red light ON; Press again, red light OFF (at basic of light on at rst
time)
Press “G” , green light ON; Press again, green light OFF (at basic of light on at
rst time)
Press “B” , blue light ON; Press again, blue light OFF (at basic of light on at rst
time)
Press “W” , white light ON; Press again, white light OFF (at basic of light on at
rst time)
Control LED ocean wave light ON/OFF
Control Laser light ON/OFF
Control device volume up
Control device volume down
Select playing previous song
Select playing next song
Voice control: Connect with Bluetooth or USB memory playing music, press
“Micro” icon, ocean wave and star light will fast-changing following music sound
Control ocean wave moving speed up (pause--Slow--Medium--Fast)
Control ocean wave moving speed down (Fast--Medium--Slow--Pause)
1
2
3
7
10
15
6
EN
4 5
14
15
16
17
18
19
20
21
Long press 3 seconds to cancel timing function. When LED, laser light ash and
emit “bleep” sound three times as prompting
Press “FADE 1”, ocean wave moves circularly in R-G-B-W single color mode
and laser light changed to gradation mode (the same feature as power on)
Press “FADE 2”, ocean wave moves circularly in RB-RG-RW-BG-BW-GW
double-color mode and laser light changed to gradation mode
Long press 3s control timing function for 1 hour. When LED, laser light ash and
emit “bleep” sound once time as prompting. 1 hour later, it’ ll automatically
switch o.
Control LED ocean wave light brightness (In order of 70%--40%--40%--70%--
100%)
Press “LASER light” achieve either Laser light stay on or enter into gradation
mode
Long press 3s control timing function for 2 hours. When LED, laser light ash
and emit “bleep” sound 2 times as prompting. 2 hours later, it’ ll automatically
switch o
Control Music Switch On/O
This product comes with 4 hours automatically shut down function that is work for 4
hours and shut down automatically.
Maximum LED Power:
Green Laser:
Power Input:
Operating Temperature:
Projection Coverage:
Product Dimensions:
Notice:
Specication
2 * 4W
< 1MW
USB DC5V / 2000mA
14 F 104 F (-10 C 40 C)
161 538 ft (15 50m )
123 * 164 mm
22
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The distance between user and products should be no less than 20cm
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device. The distance between user and products should be no less than 20cm
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.Cette modulaire doit être installé et utilisé à une distance minimum de 20 cm
entre le radiateur et le corps de l'utilisateur.
-
1
-
2
-
3
-
4
dans d''autres langues
- English: AMARYLLIS 21ARK-XKD User manual
Autres documents
-
Eicaus BL-XK01 Manuel utilisateur
-
Beamz SkyNight Projector Le manuel du propriétaire
-
LBell Night Light Projector, 3 in 1 Ocean Wave Projector Star Projector Manuel utilisateur
-
Jomst SC511 Manuel utilisateur
-
NOMVDIC L500 Manuel utilisateur
-
JVC KD-T925BTS Mode d'emploi
-
JVC KD-T92MBS Mode d'emploi
-
NOMVDIC P2000UST-RGB Manuel utilisateur
-
Sound Oasis BST-100-20 Manuel utilisateur
