Nilfisk-Advance 56263510 Aquamatic Selectric Manuel utilisateur

revised 10/00 Form Number 56041258

Aquamatic Selectric™

OPERATOR MANUAL

Advance MODELS 56263501, 56263510

FORM NO. 56041258 / Aquamatic Selectric™ - 1

TABLE OF CONTENTS

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Page

Introduction................................................................................... 2

Parts and Service.......................................................................................2

Nameplate..................................................................................................2

Uncrating the Machine ...............................................................................2

Know Your Machine ..................................................................... 3

Important Safety Instructions........................................................ 4

Importantes Mesures de Sécurité................................................. 5

Grounding Instructions ................................................................. 6

Preparing the Machine for Use..................................................... 7

Filling the Solution Tank.............................................................................7

Pre-Spraying the Carpet ............................................................................7

Plan for Cleaning .......................................................................................7

Operating the Machine ................................................................. 8

Using Attachments .....................................................................................8

After Using the Machine ............................................................... 9

Maintenance Schedule ..............................................................................9

Maintenance ............................................................................... 10

Maintenance Note ....................................................................................10

Power Brush Maintenance .......................................................................10

Pick-Up Tool Maintenance .......................................................................10

Spray Nozzle Maintenance ......................................................................10

Lubricating the Machine ...........................................................................10

Cleaning the Vacuum Exhaust Filters ......................................................11

Servicing the Vacuum Motor ....................................................................11

Servicing the Wheel Drive Motor .............................................................11

Adjusting the Brush Height ......................................................................11

Changing the Brush .................................................................................12

Troubleshooting.......................................................................... 13

Wheel Drive Circuit Breaker.....................................................................13

Brush Drive Circuit Breaker .....................................................................13

Vacuum Motor Circuit Breaker .................................................................13

2 - FORM NO. 56041258 / Aquamatic Selectric™

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

This manual will help you get the most from your Advance Selectric™. Read it thoroughly before operating the machine.

Note: Bold numbers in parentheses indicate an item illustrated on page 3.

This product is intended for commercial use only.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Advance Service Center, who employs factory trained

service personnel, and maintains an inventory of Advance original replacement parts and accessories.

Call the ADVANCE DEALER named below for repair parts or service. Please specify the Model and Serial number when

discussing your machine.

(Dealer, affix service sticker here.)

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

NAME PLATE

The Model and Serial Number of your machine are shown on the Nameplate on the right side of the machine. This

information is needed when ordering repair parts for the machine. Use the space below to note the Model and Serial

Number of your machine for future reference.

MODEL _____________________________________

SERIAL NUMBER _____________________________

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

UNCRATING THE MACHINE

When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident,

save the shipping carton so that it can be inspected by the trucking company that delivered it. Contact the trucking

company immediately to file a freight damage claim.

INTRODUCTION

FORM NO. 56041258 / Aquamatic Selectric™ - 3

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

As you read this manual, you will occasionally run across a bold number in parentheses - example: (2). These numbers

refer to an item on this page. Refer back to this page whenever necessary to pinpoint the location of an item mentioned

in the text.

1Reverse Button

2Decrease Speed Button

3Speed Indicator Lights

4Solution Button

5Increase Speed Button

6Upper Recovery Hose

7Vacuum Hose

8Recovery Tank Cover with automatic float shut-off

9Solution Fill Cover

10 Main Switch

11 Solution Filter

12 Drive Lever

KNOW YOUR MACHINE

13 Solution Valve Lever

14 Accessory Connection

15 Brush Height Adjustment

16 Brush Drive Circuit Breaker (6 Amp)

17 Wheel Drive Circuit Breaker (2 Amp)

18 Vacuum Motor Circuit Breaker (13 Amp)

19 Power Cord Connection

20 Drive Pedal

21 Brush Pedal

22 Power Cord

23 Recovery Tank Drain Hose

24 Plug Lug (A and B mating halves)

12345

6789

11

13

14

15

16

17

18

19

20

21

22

24A

23

24B

10

12

4 - FORM NO. 56041258 / Aquamatic Selectric™

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using.

WARNING!

To reduce risk of fire, electric shock, or injury:

1Do not leave the appliance when it is plugged in. Unplug the unit from the outlet when not in use and before servicing.

2To avoid electric shock, do not expose to rain. Store indoors.

3Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4Use only as described in this manual. Use only manufacturer’s recommended attachments.

5Do not use with damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left

outdoors, or dropped into water, return it to a service center.

6Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run appliance over cord. Keep cord away from heated surfaces.

7Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

8Do not handle plug or appliance with wet hands.

9Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything

that may reduce air flow.

10 Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

11 Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

12 Turn off all controls before unplugging.

13 Use extra care when cleaning on stairs.

14 Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.

15 Connect to a properly grounded outlet only. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

FORM NO. 56041258 / Aquamatic Selectric™ - 5

______________________________________________________________________________________________

L’utilisation d’un appareil électrique demande certaines précautions:

LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL)

AVERTISSEMENT:

Pour réduire les risques d’incendie, de choc électrique ou de blessure:

1Ne pas laisser l’appareil sans surveillance lorsqu’il est branché. Débrancher lorsque l’appareil n’est pas utilisé et avant

l’entretien.

2Pour réduire les risques de choc électrique, utiliser à l’intérieur seulement.

3Ne pas permettre aux enfants de jouer avec l’appareil. Une attention particulière est nécessaire lorsque l’appareil

est utilisé par des enfants ou à proximité de ces derniers.

4N’utiliser que conformément à cette notice avec les accessoires recommandés par le fabricant.

5Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner l’appareil à un atelier de réparation s’il ne fonctionne

pas bien, s’il est tombé ou s’il a été endommagé, oublié à l’extérieur ou immergé.

6Ne pas tirer soulever ou traîner l’appareil par le cordon. Ne pas utiliser le cordon comme une poignée, le coincer dans

l’embrasure d’une porte ou l’appuyer contre des arêtes vives ou des coins. Ne pas faire rouler l’appareil sur le cordon.

Garder le cordon à l’écart des surfaces chaudes.

7Ne pas débrancher en tirant sur le cordon. Tirer plutôt la fiche.

8Ne pas toucher la fiche ou l’appareil lorsque vos mains sont humides.

9N’insérer aucun objet dans les ouvertures. Ne pas utiliser l’appareil lorsqu’une ouverture est bloquée. S’assurer que

de la poussière, de la peluche, des cheveux ou d’autres matières ne réduisent pas le débit d’air.

10 Maintenir les cheveux, les vêtements amples, les doigts et toutes les parties du corps à l’écart des ouvertures et des

pièces mobiles.

11 Ne pas aspirer de matières en combustion ou qui dégagent de la fumée, comme des cigarettes, des allumettes ou

des cendres chaudes.

12 Mettre toutes les commandes à la position ARRÊT avant de débrancher l’appareil.

13 User de prudence lors du nettoyage des escaliers.

14 Ne pas aspirer des liquides inflammables or combustibles, comme de l’essence, et ne pas faire fonctionner dans des

endroits ou peuvent se trouver de tels liquides.

15 Ne brancher qu’à une prise de courant avec mise à la terre. Voir les instructions visant la mise à la terre.

CONSERVER CES INSTRUCTIONS

IMPORTANTES MESURES DE SÉCURITÉ

6 - FORM NO. 56041258 / Aquamatic Selectric™

GROUNDING INSTRUCTIONS

Figure 2

Figure 1

Adapter

Metal

Screw

Grounded

Outlet Box

Tab for

Grounding

Screw

Grounded

Outlet Box

Grounding

Grounded

Outlet

This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for

electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-

grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed

and grounded in accordance with all local codes and ordinances.

DANGER!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified

electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug

provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure

1. A temporary adapter illustrated in Figure 2 may be used to connect this plug to a 2-pole receptacle as shown in Figure

2 if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded

outlet (Figure 1) can be installed by a qualified electrician. The green-colored rigid ear, tab, or the like extending from

the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the

adapter is used, it must be held in place by a metal screw.

Note: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.

FORM NO. 56041258 / Aquamatic Selectric™ - 7

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BEFORE USING THE SELECTRIC

1 Thoroughly vacuum the carpet to be cleaned before using the Selectric automatic extractor.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

FILLING THE SOLUTION TANK

1Lift the front Solution Fill Cover (9) off the machine.

2Read the dilution instructions on the chemical container. Then figure the proper amount of chemical to mix with 25

gallons (94.5 liters) of water. For best results, use the Advance CarpeTeam™ Extraction Cleaner chemical specially

formulated for use with Advance carpet extractors.

3Pour the chemical in the solution tank and fill the tank with warm water to 2 inches below the inside edge of the opening.

4Put the Solution Fill Cover back on the machine.

CAUTION!

Use only low-sudsing, liquid detergents designed for carpet extraction.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

PRE-SPRAYING THE CARPET

Pre-spray spots and heavy traffic areas before extracting. Use a hand-held bottle sprayer or a pressurized “Hudson”

type sprayer. Mix the pre-spray according to the chemical manufacturer’s directions. For best results, use the Advance

CarpeTeam™ Pre-Spray chemical specially formulated for use with Advance carpet extractors.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

PLAN FOR CLEANING

Before you begin extracting, look at the area to be cleaned and plan your work. Divide the space into sections. Overlap

each pass 2 inches (5 cm).

PREPARING THE MACHINE FOR USE

8 - FORM NO. 56041258 / Aquamatic Selectric™

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

1Follow the instructions in the Preparing the Machine for Use section of this manual.

2Slide the Plug Lug halves (24A & 24B) together. Connect the Power Cord (22) to the machine at the Power Cord

Connection (19), then plug the Power Cord into a properly grounded outlet.

3Make sure the Solution Fill Cover (9) and the Recovery Tank Cover (8) are firmly in place and the Solution Valve Lever

(13) is in the ON position.

4Turn the Main Switch (25) ON. The Solution Button (4) will light up to indicate that the solution is ON.

5Put the Brush Pedal (21) UP to lower the brush to the floor.

6Step DOWN on the Drive Pedal (20) and push the pedal to the right to engage the drive motor.

7Pull and hold the Drive Levers (26) UP to propel the machine. To adjust the travel speed, press the Increase Speed

Button (5) or the Decrease Speed Button (2). To move backward, hold down the Reverse Button (1) while pulling the

Drive Levers; release the Reverse Button to move forward again.

Note: There will be a slight pause between direction changes.

8 Solution is dispensed only while moving forward and automatically shuts off in reverse. Press the Solution Button

(4) to stop solution flow; the light will turn off.

9Watch the fluid entering the recovery tank cover (8). If there is a large amount of suds in the recovery tank, add a

defoamer chemical to the recovery tank.

CAUTION!

Empty the recovery tank before the fluid or foam enters the Vacuum Hose (7) on the right side of the recovery tank

cover.

If there is little or no fluid entering the recovery tank, look to the clear solution hose on the right side of the machine.

If there is no fluid running through the solution hose, the solution tank may be empty. Refill the solution tank with water

and the proper ratio of cleaning chemical.

10 The recovery tank has an automatic float shut-off to block the vacuum system when the recovery tank is full. You can

tell when the float closes by the sudden change in the sound of the vacuum motor. When the float closes, the recovery

tank must be emptied. The machine will not pick up water with the float closed.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

USING ATTACHMENTS

To use accessory tools, attach the accessory recovery hose to the left port of the recovery tank cover. Attach the

accessory solution hose to the Accessory Connection (14). Connect the other ends of the hoses to the accessory tool.

When using accessory tools, step DOWN on the Brush Pedal (18) to raise the brush.

See your Advance Distributor for accessories that may be used with the Selectric including:

• 56249360 Liquidator

• 56204223 Drag Tool SS 4 Ft

• 56204224 Hand Tool SS

• 56249318 Scrub & Vac Hose 15 Ft

• 56801000 Aqua Kit (Includes PN 56800385, 56800390 & 56249318)

• 56800390 Drag Tool (Plastic)

• 56800385 Hand Tool (Plastic)

OPERATING THE MACHINE

revised 10/00

FORM NO. 56041258 / Aquamatic Selectric™ - 9

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

1Turn the Main Switch (25) OFF.

2Step DOWN and lock the Brush Pedal (21) to raise the brush.

3Put the Drive Pedal (20) UP to disengage the drive belt.

4Unplug the Power Cord (22) from the power outlet and from the machine.

5Unhook the Recovery Tank Drain Hose (23), direct the hose to a “DESIGNATED” waste water disposal site. Remove

the hose plug to empty the recovery tank and rinse it with clean water.

6Separate the upper section of the Recovery Hose (6) at the back of the machine, then remove the Solution Fill Cover

(9) and place the recovery hose into the bottom of the solution tank. Turn on the Main Switch (25) and vacuum the

unused solution into the recovery tank. Unhook the Recovery Drain Hose (23), direct the hose to a “DESIGNATED”

waste water disposal site. Remove the plug to empty and rinse with clean water.

7Unscrew the Solution Filter (11) cover and clean the screen.

8Wipe the machine with a damp cloth. Do not use abrasive chemicals or solvents.

9Perform any required maintenance before storage.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

MAINTENANCE SCHEDULE

MAINTENANCE ITEM WEEKLY MONTHLY YEARLY

Clean and Check Power Brush •

Clean Pick-Up Tool •

Clean Spray Nozzle •

Lubricate the Machine •

Clean the Vacuum Exhaust Filter •

*Service the Vacuum Motor •

Service the Wheel Drive Motor •

*Have the carbon brushes in the vacuum motor checked once a year or after every 500 hours by a qualified Advance

service person.

10 Store the machine in a clean, dry place with the tank covers open.

AFTER USING THE MACHINE

10 - FORM NO. 56041258 / Aquamatic Selectric™

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

WARNING!

Unplug the power cord before attempting any service or maintenance work to the machine.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

MAINTENANCE NOTE

With the tanks empty and the power cord unplugged, tip the machine forward onto its nose for access to the Power Brush,

Pick-Up Tool, and Spray Nozzle.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

POWER BRUSH MAINTENANCE

Check the brush once a week. Remove any built-up string, hair or carpet fibers. Check the bristle length. Change the

brush when the brush bristles are worn to 1/4 inch (6 mm).

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

PICK-UP TOOL MAINTENANCE

Check the pick-up tool once a week. Remove any built-up string, hair or carpet fibers.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SPRAY NOZZLE MAINTENANCE

Remove the spray nozzle once a week. It is located under the machine just in front of the brush. Soak the nozzle

overnight in a vinegar and water solution to remove chemical deposits.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

LUBRICATING THE MACHINE

Once a month (or every 30 hours), lubricate all pivot points on the pick-up tool. For best results, use a spray silicone

lubricant.

Once a month, pump grease into the grease fitting on the caster wheel until it seeps out around the bearing. Wipe off

the excess grease to avoid staining carpet.

MAINTENANCE

FORM NO. 56041258 / Aquamatic Selectric™ - 11

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

CLEANING THE VACUUM EXHAUST FILTERS

Clean the vacuum exhaust filters once a month. Remove the filter holder from the bottom of the machine and vacuum

to remove any dust or debris that may block air flow. For extremely dirty filters, wash with warm, soapy water and rinse

thoroughly with clean water. Allow the filter to dry completely before installing back on the machine.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SERVICING THE VACUUM MOTOR

Have the carbon brushes in the vacuum motor checked once a year or after every 500 hours by a qualified Advance

service person.

IMPORTANT!

Motor damage resulting from failure to service carbon brushes is not covered under warranty. See the Limited Warranty

statement.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SERVICING THE WHEEL DRIVE MOTOR

Have the carbon brushes in the wheel drive motor checked every 450 hours by a qualified Advance service person.

IMPORTANT!

Motor damage resulting from failure to service carbon brushes is not covered under warranty. See the Limited Warranty

statement.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

ADJUSTING THE BRUSH HEIGHT

There is an Adjustment Plate (15) on each side of the machine, just in front of the brush. To adjust the Brush Height,

loosen the two Plate Screws on the side of the Adjustment Plates. Raise the plates to lower the brush; Lower the plates

to raise the brush. Use a wrench to turn the Adjustment Screws to the desired position, then tighten the Plate Screws.

MAINTENANCE

Adjusting the Brush Height

Adjustment Screw

Adjustment Plate

Plate Screws

FRONT

12 - FORM NO. 56041258 / Aquamatic Selectric™

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

CHANGING THE BRUSH

Change the brush when the brush bristles are worn to 1/4 inch (6 mm).

1Remove the Belt Guard from the left side of the machine.

2Loosen the brush drive motor mount and slip the Belt off the motor pulley.

3Tip the machine on its nose. Then pry the Belt Cover off the Brush Housing.

4Pull the pulley end of the brush out of the Brush Housing.

5Inspect the Belt for wear or damage, replace if necessary.

6Place the Belt around the pulley on the new brush. Install the brush in the Brush Housing so that number 1 is visible

on both bearing blocks.

7Place the Belt over the motor pulley and tighten the motor mount.

8Install the Belt Cover and Belt Guard.

MAINTENANCE

Number 1

on Bearing Blocks

Brush Housing

Changing the Brush

Belt

Belt Cover

FORM NO. 56041258 / Aquamatic Selectric™ - 13

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

2 AMP WHEEL DRIVE CIRCUIT BREAKER

When the Wheel Drive Circuit Breaker (17) trips, check to see if there is debris wrapped around the wheel axle. Remove

the debris from the axle. Have the wheel drive motor checked for worn out brushes; repair or replace the motor if

necessary. Push the button to reset the circuit breaker.

If the circuit breaker trips repeatedly, call your local Advance Distributor for service.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

6 AMP BRUSH DRIVE CIRCUIT BREAKER

When the Brush Drive Circuit Breaker (16) trips, check to see if the brush height is set too low or if there is debris wrapped

around the brush. Adjust the brush height or remove the debris from the brush. Push the button to reset the circuit

breaker.

If the circuit breaker trips repeatedly, call your local Advance Distributor for service.

_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

13 AMP VACUUM MOTOR CIRCUIT BREAKER