Dell PowerEdge R805 Manuel utilisateur

Dell™ PowerEdge™

R805 Systems

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Dell™ PowerEdge™

R805 Systems

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; AMD and AMD

Opteron are registered trademarks of Advanced Micro Devices; Microsoft, Windows, and Windows

Server are registered trademarks of Microsoft Corporation; Novell and NetWare are registered

trademarks of Novell, Inc.; Red Hat and Red Hat Enterprise Linux are registered trademarks

of Red Hat, Inc.; SUSE is a registered trademark of Novell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model EMS01

August 2007 P/N NX702 Rev. A00

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your

system. It also provides information about other documents you may need

when setting up your system and how to obtain technical assistance.

• Two dual-core or quad-core AMD Opteron™ processors.

• A minimum of 2 GB single- or dual-ranked 667-MHz DDR2 (PC2-5300)

memory modules (installed in two sets of pairs). Memory is upgradable to

a maximum of 128 GB by installing combinations of 512-MB, 1-GB, 2-GB,

4-GB, or 8-GB memory modules in the 16 memory module sockets

(eight per CPU) on the system board.

• Support for up to two 2.5-inch, internal hot-pluggable Serial Attached

SCSI (SAS) or SATA hard drives.

• An optional slim-line SATA DVD-ROM drive, slim-line SATA DVD-RW

drive, or combination CD-RW/DVD drive (when available).

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management

software if the cover is opened.

• Up to two hot-pluggable, 700-W power supplies in an optional 1 + 1

redundant configuration.

• Six hot-pluggable system cooling fans.

• Optional support for iSCSI boot.

The system board includes the following features:

• A right riser card (riser 1) containing two PCIe (x4 and x8) slots. The right

riser card also contains an SD (Secure Digital) slot for embedded OS

support.

• A left riser card (riser 2) containing one full-length PCIe (x8) slot

and one half-length PCIe (x8) slot.

• An integrated SAS controller card (via a dedicated PCIe slot on the

sideplane board) supporting both SAS 6i/R and PERC 6/i adapters.

• Optional integrated PERC controller (PERC 6i) with integrated cache

and battery backup.

• Four integrated Gigabit Ethernet NICs, capable of supporting 10-Mbps,

100-Mbps, and 1000-Mbps data rates.

4 Getting Started With Your System

• Four external USB 2.0-compliant connectors (two on the front and two

on the back) supporting a diskette drive, a DVD-ROM drive, a keyboard,

a mouse, or a USB flash drive.

• One internal USB 2.0-compliant connector supporting an optional

bootable USB flash drive or USB security key.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem based on an integrated

ATI ES1000 33-MHz PCI video controller. The video subsystem includes

32MB of graphics memory and supports various 2D graphics video modes.

Maximum resolution is 1600x1200 with 65,536 colors. (When the optional

RAC is installed, the maximum resolution of the integrated video

subsystem is 1280x1024.)

• Systems management circuitry that monitors operation of the system fans

as well as critical system voltages, temperatures, and system power

consumption. The systems management circuitry works in conjunction

with the systems management software.

• Standard Baseboard Management Controller (BMC) with serial and LAN

access.

• Back-panel connectors include one serial, one video, two USB,

and four NIC connectors.

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see Technical Specifications.

Supported Operating Systems

• Microsoft

®

Windows Server

®

2003 R2 Standard and Enterprise Editions

(SP1 and later)

• Microsoft Windows Server 2003 R2 Standard and Enterprise x64 Editions

(SP1 and later)

• Red Hat Enterprise Linux Server 5 (x86)

• Red Hat Enterprise Linux Server 5 (x86_64)

• Red Hat Enterprise Linux Server ES (Version 4.5) (x86)

Getting Started With Your System 5

• Red Hat Enterprise Linux Server ES (Version 4.5) (x86_64)

•SUSE

®

Linux Enterprise Server 9 (x86_64)

• SUSE Linux Enterprise Server 10 (x86_64)

•VMware

®

ESX Server 3 (including embedded versions)

NOTE: For the latest information on supported operating systems, see www.dell.com.

NOTE: SUSE Linux Enterprise Server 9, prior to SP4, does not support SATA optical

devices. Installation must be performed using other methods, such as an external

USB CD-ROM drive.

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

• The

Rack Installation Guide

or

Rack Installation Instructions

included

with your rack solution describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components.

• CDs included with your system provide documentation and tools for

configuring and managing your system.

• Systems management software documentation describes the features,

requirements, installation, and basic operation of the software.

• Operating system documentation describes how to install (if necessary),

configure, and use the operating system software.

• Documentation for any components you purchased separately provides

information to configure and install these options.

• Updates are sometimes included with the system to describe changes

to the system, software, and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

6 Getting Started With Your System

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Hardware Owner’s Manual.

Dell™ Enterprise Training and Certification is available; see

www.dell.com/

training

for more information. This service may not be offered in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the

safety instructions and important regulatory information in your Product

Information Guide.

This section describes the steps to set up your system for the first time.

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

NOTE: Depending on options ordered, not all components shown may be

included.

Getting Started With Your System 7

Installing the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack

installation documentation for your system, install the rails and the system

in the rack.

See your rack installation documentation for instructions on installing

your system in a rack.

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating

which cable to plug into each connector. Be sure to tighten the screws

(if any) on the monitor's cable connector.

8 Getting Started With Your System

Connecting the Power

Connect the monitor’s power cable to the monitor (optional), and connect

the system’s power cable(s) to the system.

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power

supply handle. Bend the system power cable into a loop as shown in the

illustration and attach to the bracket’s cable clasp. Repeat the procedure

for the second power supply.

Plug the other end of the power cables into a grounded electrical outlet

or a separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

Getting Started With Your System 9

Turning on the System

Turn on the system and monitor (optional).

With the bezel removed, press the power button on the system and the

monitor. The power indicators should light. Adjust the monitor's controls

until the displayed image is satisfactory.

Installing the Bezel

Install the bezel (optional).

10 Getting Started With Your System

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the Quick Installation Guide. Be sure the operating system

is installed before installing hardware or software not purchased with the

system.

Technical Specifications

Processor

Processor type Two dual- or quad-core AMD Opteron processors

Expansion Bus

Bus type PCIe

Expansion slots

Right riser (riser 1):

PCIe

One x8 full-height, full-length slot (top)

One x4 full-height, half-length slot (bottom)

One internal SD (Secure Digital) card slot

Left riser (riser 2):

PCIe

One x8 full-height, full-length slot (top)

One x8 full-height, half-length slot (bottom)

One internal USB key socket

Memory

Architecture 667-MHz registered parity DDR2 memory

modules

Memory module sockets 16 240-pin

Memory module capacities 512 MB, 1 GB, 2 GB, 4 GB, or 8 GB (single-

or dual-rank only, quad-rank not supported)

Minimum RAM

(installed in two sets of pairs)

2 GB (1 GB each processor, 2 DIMMs

per processor)

Maximum RAM 128 GB (64 GB each processor)

Getting Started With Your System 11

Drives

Hard drives Up to two 2.5-inch, hot-plug SAS or SATA

internal drives

Optical drive One optional slim-line SATA DVD-ROM drive or

DVD-RW drive, or combination CD-RW/DVD

drive (when available)

NOTE: DVD devices are data only.

External optional USB DVD

Flash drive External optional USB

Internal optional USB

Internal optional SD card

Connectors

Back

NIC

Four RJ-45 10/100/1000

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

SD

One flash memory card slot on right PCIe riser

(riser 1)

Video

Video type ATI ES1000 video controller; VGA connector

Video memory 32 MB

12 Getting Started With Your System

Power

AC power supply (per power supply)

Wa tt ag e

700 W

Voltage

85–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2697 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 55 A per power supply

for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Physical

Height

8.67 cm (3.41 in)

Width

44.4 cm (17.5 in)

Depth

71.26 cm (28.05 in)

Weight (maximum

configuration)

20.23 kg (44.6 lb)

Getting Started With Your System 13

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing) with a maximum

humidity gradation of 10% per hour

Maximum vibration

Operating

0.26 Grms at 5–350 Hz in operational

orientations

Storage

1.54 Grms at 10–250 Hz in all orientations

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for 2.6 ms

in the operational orientation

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

14 Getting Started With Your System

Systèmes Dell™

PowerEdge™ R805

Guide de mise en route

Modèle EMS01

Remarques, avis et précautions

REMARQUE : Une REMARQUE indique des informations importantes qui peuvent

vous aider à mieux utiliser votre ordinateur.

AVIS : Un AVIS vous avertit d'un risque de dommage matériel ou de perte de

données et vous indique comment éviter le problème.

PRÉCAUTION : Une PRÉCAUTION indique un risque potentiel d'endommagement

du matériel, de blessure corporelle ou de mort.

____________________

Les informations contenues dans ce document peuvent être modifiées sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.

est strictement interdite.

Marques utilisées dans ce document : Dell et le logo DELL sont des marques de Dell Inc. ; AMD et AMD

Opteron sont des marques déposées d'Advanced Micro Devices ; Microsoft, Windows e t Windows Server

sont des marques déposées de Microsoft Corporation ; Novell et NetWare sont des marques déposées

de Novell, Inc. ; Red Hat et Red Hat Enterprise Linux sont des marques déposées de Red Hat, Inc. ;

SUSE est une marque déposée de Novell Inc.

D'autres marques et noms de marques peuvent être utilisés dans ce document pour faire référence

aux entités se réclamant de ces marques et de ces noms ou à leurs produits. Dell Inc. dénie tout intérêt

propriétaire vis-à-vis des marques et des noms de marque autres que les siens.

Modèle EMS01

Août 2007 N/P NX702 Rév. A00

Guide de mise en route 17

Caractéristiques du système

Cette section décrit les principales caractéristiques du système sur le plan

matériel et logiciel. Elle contient également des informations sur les autres

documents utiles à la configuration du système et sur l'obtention d'assistance

technique.

• Deux processeurs AMD Opteron™ double cœur ou quadruple cœur.

• Barrettes de mémoire DDR2 (PC2-5300) à simple ou double rangée de

connexions, cadencées à 667 MHz et totalisant au moins 2 Go (installées

dans deux groupes de paires). La mémoire est extensible à un maximum

de 128 Go via l'installation de combinaisons de barrettes de 512 Mo, 1 Go,

2 Go, 4 Go ou 8 Go dans les 16 emplacements mémoire (huit par

processeur) de la carte système.

• Prise en charge de deux disques durs SAS (Serial-Attached SCSI) ou SATA

internes de 2,5 pouces, enfichables à chaud.

• Un lecteur de DVD-ROM slim SATA, un lecteur de DVD-RW slim SATA

ou un lecteur combo CD-RW/DVD (selon disponibilité). Tous ces

éléments sont disponibles en option.

REMARQUE : Les périphériques DVD sont uniquement des périphériques

de données.

• Un détecteur d'intrusion qui transmet une alerte aux logiciels de gestion

de système appropriés en cas d'ouverture du capot de l'ordinateur.

• Jusqu'à deux blocs d'alimentation de 700 W enfichables à chaud dans

une configuration redondante 1+1 (facultative).

• Six ventilateurs enfichables à chaud.

• Support en option pour l'amorçage iSCSI.

La carte système offre les caractéristiques suivantes :

• Carte de montage de droite (numéro 1) dotée de deux emplacements

PCIe (x4 et x8). Cette carte contient également un logement SD

(Secure Digital) pour le support intégré du système d'exploitation.

• Carte de montage de gauche (numéro 2) comprenant deux logement

PCIe x8 dont un emplacement pleine longueur et un emplacement

mi-longueur.

18 Guide de mise en route

• Carte contrôleur SAS intégrée (via un emplacement PCIe dédié sur

la carte latérale) prenant en charge à la fois les adaptateurs SAS 6i/R

et PERC 6/i.

• Contrôleur PERC 6i intégré en option, avec mémoire cache intégrée

et batterie de sauvegarde.

• Quatre NIC Ethernet Gigabit intégrés pouvant prendre en charge

des débits de données de 10, 100 et 1 000 Mbps.

• Quatre connecteurs USB 2.0 externes (deux à l'avant et deux à l'arrière)

pour la connexion d'un périphérique externe (lecteur de disquette ou

de DVD-ROM, clavier, souris ou lecteur flash USB).

• Un connecteur USB 2.0 interne prenant en charge un lecteur flash USB

amorçable ou une clé de sécurité USB, tous deux disponibles en option.

• Un contrôleur d'accès à distance (RAC) en option, pour la gestion

de système à distance.

• Un sous-système vidéo intégré compatible VGA, avec contrôleur vidéo

ATI ES1000 intégré à 33 MHz. Ce sous-système dispose de 32 Mo de

mémoire graphique avec prise en charge de divers modes graphiques

en 2D. La résolution maximale est de 1 600 x 1 200 avec 65 536 couleurs.

Si le contrôleur RAC en option est installé, la résolution maximale du

sous-système vidéo intégré est de 1 280 x 1 024.

• Des circuits intégrés de gestion de système surveillant le fonctionnement

des ventilateurs, ainsi que les tensions et les températures critiques,

ou encore la consommation énergétique du système. Ces circuits de

surveillance fonctionnent de pair avec les logiciels de gestion de système.

• Un contrôleur BMC (Baseboard Management Controller) standard avec

accès série et réseau local.

• Le panneau arrière contient un connecteur vidéo, un port série, deux ports

USB et quatre connecteurs de NIC.

• Le panneau avant comprend un connecteur vidéo et deux connecteurs USB.

• Un écran LCD 1x5 sur le panneau avant, affichant l'ID du système et

les messages d'erreur.

• Un bouton d'ID du système sur les panneaux avant et arrière.

Pour plus d'informations sur des caractéristiques spécifiques,

voir “Spécifications techniques”.

La page charge ...

Dell PowerEdge R805 Manuel utilisateur

Ce manuel convient également à

Dell PowerEdge R805 Manuel utilisateur

dans d''autres langues

Documents connexes