TechniSat DigitRadio UP1 Le manuel du propriétaire

DIGITRADIO UP 1

DAB+/FM recessed radio with Bluetooth

2

CONTENTS

ENGLISH ........................................................................................... 3-34

FRANÇAIS ..................................................................................... 35-66

ITALIANO ........................................................................................67-98

NEDERLANDS ............................................................................ 99-130

NORSK ......................................................................................... 131-162

DANSK ........................................................................................ 163-194

POLSKE ..................................................................................... 195-226

ČEŠTINA .................................................................................... 227-258

SLOVENSKÉ ............................................................................ 259-290

Instruction Manual

DIGITRADIO UP 1

DAB+/FM recessed radio with Bluetooth

EN

FR

IT

NL

NW

DK

PL

CZ

SK

Contents

1 Foreword ..................................................................................................................... 6

1.1 Target group for this instruction manual ......................................................................... 6

1.1.1 Intended use ................................................................................................................................. 6

1.2 Important information .............................................................................................................. 6

1.2.1 Safety .................................................................................................................................................7

1.2.2 Disposal ........................................................................................................................................... 8

1.2.3 Legal notices ............................................................................................................................... 10

1.2.4 Service instructions .................................................................................................................. 10

2 Illustration and buons .......................................................................................... 11

3 Connection and assembly of the DIGITRADIO UP1 ....................................... 12

4 Description of the DIGITRADIO UP1 ....................................................................13

4.1 Scope of delivery ........................................................................................................................ 13

4.2 The special features of the DIGITRADIO UP1 ................................................................13

5 General device functions .......................................................................................13

5.1 Switching on the device .........................................................................................................13

5.2 Switching o the device .........................................................................................................13

5.3 Changing to DAB+/FM/Bluetooth mode ........................................................................13

5.4 Adjusting the volume ...............................................................................................................13

5.5 Retrieving displays .................................................................................................................... 14

6 Menu operation ....................................................................................................... 14

7 DAB+ (digital radio) function ............................................................................... 15

7.1 What is DAB+? ............................................................................................................................15

7.1.1 Data compression ......................................................................................................................15

7.1.2 Audio stream ................................................................................................................................15

7.2 DAB+ (digital radio) reception .............................................................................................15

7.2.1 Performing a complete scan ...............................................................................................15

7.2.2 Selecting stations ...................................................................................................................... 16

7.2.3 Storing DAB+ stations on a memory slot ...................................................................... 16

7.2.4 Retrieving DAB+ stations from a memory slot ........................................................... 16

7.2.5 Overwriting/deleting a station memory slot ................................................................ 16

7.2.6 Signal intensity ............................................................................................................................17

7.2.7 Manual seing .............................................................................................................................17

7.2.8 Volume adjustment (DRC) .....................................................................................................17

7.2.9 Deleting inactive stations .......................................................................................................17

8 FM mode .................................................................................................................... 18

8.1 Switching on FM radio mode .............................................................................................. 18

8.2 FM reception with RDS information ................................................................................. 18

8.3 Automatic station scan .......................................................................................................... 18

8.4 Manual station scan ................................................................................................................. 18

8.5 Scan seing ................................................................................................................................. 18

8.6 Audio seings ............................................................................................................................. 19

4

8.7 Saving FM stations to a memory slot .............................................................................. 19

8.8 Retrieving FM stations from a memory slot ................................................................. 19

8.9 Overwriting/deleting a station memory slot ................................................................ 19

9 Bluetooth ................................................................................................................... 19

9.1 Pairing a device ........................................................................................................................ 20

9.2 Bluetooth playback ................................................................................................................. 20

10 Other functions ........................................................................................................ 21

10.1 Sleep timer ................................................................................................................................... 21

10.2 Alarm .............................................................................................................................................. 21

10.2.1 Seing the alarm time ............................................................................................................ 21

10.2.2 Switching o the alarm aer being woken ..................................................................22

10.2.3 Deactivating the alarm ...........................................................................................................22

10.3 Equaliser ........................................................................................................................................22

11 System seings ........................................................................................................ 23

11.1 Time and date seings ........................................................................................................... 23

11.1.1 Manually seing the time/date ..........................................................................................23

11.1.2 Time update ................................................................................................................................23

11.1.3 Seing the time format ......................................................................................................... 24

11.1.4 Seing the date format ........................................................................................................ 24

11.2 Display brightness ................................................................................................................... 24

11.3 Language ......................................................................................................................................25

11.4 Factory seing ............................................................................................................................25

11.5 Soware version ........................................................................................................................25

12 Cleaning .....................................................................................................................26

13 Troubleshooting ......................................................................................................26

14 Technical data .......................................................................................................... 27

15 Installation ................................................................................................................ 27

5

EN

FR

IT

NL

NW

DK

PL

CZ

SK

1 Foreword

This instruction manual will help you to use your radio device, hereinaer referred to

as DIGITRADIO or device, as intended and safely.

1.1 Target group for this instruction manual

The instruction manual is intended for anyone who is installing, operating, cleaning or

disposing of the device.

1.1.1 Intended use

Please read this instruction manual carefully. This is the only way to operate your

device safely and correctly. Keep the instruction manual in a safe place for use at a

later date.

The device has been designed to receive DAB+/FM radio programmes.

Furthermore, it can receive music streams via Bluetooth if another device is

connected. The device has been designed for private use and not for commercial

purposes.

Caution!

This device is only intended for installation.

Only a licensed specialist is allowed to connect devices without connectors.

Risk of electric shock!

In the event of damage resulting from incorrect connection, no warranty claim can be

made.

In the event of having to completely disconnect the device from the power supply

(storm, prolonged absence), this should be performed using a switch.

1.2 Important information

Please take note of the following information to minimise safety risks, to prevent

damage to the device and to make a contribution to environmental protection.

Please read all the safety information carefully and keep it for future reference.

Always follow all the warnings and instructions in this instruction manual and on the

rear of the device.

Caution - This identiﬁes important information that must be observed to

prevent device defects, data loss/misuse or undesired operation.

Tip - This identiﬁes information relating to the described function, as well

as to another related function that may have to be taken into account, with

reference to the corresponding section in the manual.

6

1.2.1 Safety

For your own safety, you should read through the safety precautions carefully before

you put your DIGITRADIO UP1 into operation. The manufacturer accepts no liability

for damage caused by inappropriate handling, or by non-compliance with the safety

precautions.

This device is only intended for installation. Only a licensed specialist is allowed

to connect devices without connectors. Risk of electric shock! In the event of

damage resulting from incorrect connection, no warranty claim can be made.

Do not open the device under any circumstances!

Touching live parts poses a danger to life!

Any necessary repairs to the receiver should only be carried out by qualiﬁed

personnel.

The device must only be operated in an appropriate climate.

Do not expose the device to dripping or splashing water. If water has

penetrated the device, switch it o and inform the Service department.

Do not expose the device to heat sources that will heat it up more than

normal use.

If you detect a device defect, odour or smoke, considerable malfunctions,

or damage to the housing, switch o the device and inform the Service

department.

The device must only be connected to a mains voltage of 100V-240V~, 50/60

Hz.

Never try to operate the device with another voltage.

If the device shows signs of damage, it may not be put into operation.

7

EN

FR

IT

NL

NW

DK

PL

CZ

SK

Do not put the device into operation in the vicinity of baths, swimming pools

or splashing water.

Never try to repair a faulty device yourself. Always contact one of our customer

service locations.

Foreign bodies, e.g. nails, coins, etc. must not be allowed to fall inside the

device. Do not touch the connection contacts with metal objects or ﬁngers.

This could lead to short-circuits.

Never allow children to use the device unsupervised.

Even when switched o and on standby, the device is still connected to the

mains power supply.

Do not listen to music or the radio at high volume. Doing so can cause

permanent hearing impairment.

This device is not intended to be used by people (including children) with

limited physical, sensoryormentalcapacities or lackof experienceand/or

knowledge,unless they are supervised by a person responsible for their safety

or they are instructed by them as to how to use the device.

Children must be supervised to ensure that they do not play with the device.

It is forbidden to carry out modiﬁcations to the device.

Damaged devices or damaged accessories must not continue to be used.

1.2.2 Disposal

The device packaging is exclusively comprised of recyclable materials. Please sort

these and take them to the "Dual System." At the end of its service life, this device

must not be disposed of with your regular household waste. It must be taken to a

recycling collection point for electrical and electronic equipment.

This is indicated by the symbol on the product, the instruction manual or the

packaging.

The materials are recyclable according to their identiﬁcation.

An important contribution is made to our environment by recycling, recovery of

materials or other kinds of recycling for old devices.

8

Please ask local authorities for the location of the relevant disposal point. Ensure that

used baeries/rechargeable baeries as well as electronic waste are not disposed of

with domestic waste, but are properly disposed of (returned to the specialist shop,

hazardous waste).

Disposal instructions:

Disposal of packaging:

Your new device was protected by packaging on its way to you. All materials

used are environmentally friendly and recyclable. Please collaborate and

dispose of the packaging in an environmentally-friendly way. Ask for

information from your dealer regarding current disposal means or regarding

your local disposal facility.

Risk of suocation! Do not give packaging and parts thereof to children. Risk

of suocation by ﬁlms and other packaging materials.

Device disposal:

Old devices constitute valuable waste. Valuable raw materials can be

recovered through environmentally-friendly disposal. Consult your town or

local authority as to the possibilities for environmentally-friendly and proper

disposal of the device. Prior to disposal of the device, remove the baeries/

rechargeable baeries contained therein.

This device is identiﬁed in accordance with the Waste Electrical and Electronic

Equipment (WEEE) Directive2012/19/EU.

At the end of its service life, this device must not be disposed of with your

regular household waste. It must be taken to a recycling collection point for

electrical and electronic equipment. The symbol on the product, the operating

manual or the packaging indicates this. The materials are recyclable according

to their identiﬁcation. An important contribution is made to our environment

by recycling, recovery of materials or other kinds of recycling for old devices.

9

EN

FR

IT

NL

NW

DK

PL

CZ

SK

1.2.3 Legal notices

TechniSat herewith declares that the radio system model DIGITRADIO UP1

corresponds to Directive 2014/53/EU. The complete text of the EU declaration

of conformity is available at the following website:

hp://konf.tsat.de/?ID=11471

TechniSat accepts no liability for product damage as a result of external

inﬂuences, wear or improper handling, unauthorised repairs, modiﬁcations or

accidents.

Changes and printingerrors reserved. Version 02/18.

Copy and reproduction are subject to the publisher's consent. The respective

current version of the manual can be obtained in PDF format in the

download area of the TechniSat homepage at www.technisat.de.

DIGITRADIO UP1 and TechniSat are registered trademarks of:

TechniSat Digital GmbH

TechniPark

Julius-Saxler-Strasse 3

D-54550 Daun/Eifel, Germany

www.technisat.de

1.2.4 Service instructions

This product is quality-tested and provided with the legal warranty period of

24 months as from the date of purchase. Please keep your receipt as proof of

purchase. In the event of warranty claims please contact the product dealer.

Note!

Should you experience a problem with this device, or for queries and

information, our Technical Hotline is available:

Mon. - Fri. 8:00 am - 8:00 pm on tel.:

+49 (0) 3925 9220 1800.

10

If the device needs to be sent back, please use the following address only:

TechniSat Digital GmbH

Service-Center

Nordstr. 4a

39418 Staßfurt, Germany

The names of the companies, institutions or makes referred to are trademarks or

registered trademarks of the respective owners.

2 Illustration and buons

2 3 4 5 6 7 8 9

1

10

1 Display

2 On/Standby/Mode change

3 Info/Menu retrieval buon

4 Reduce selection/menu operation

5 Preset buon

6 Enter/Conﬁrm selection/Save/Snooze buon

7 Reduce volume

8 Increase selection/Menu operation

9 Increase volume

10 Speaker

11

EN

FR

IT

NL

NW

DK

PL

CZ

SK

3 Connection and assembly of the DIGITRADIO UP1

Caution!

> This device is only intended for installation. Work on the 230 V network may

only be performed by qualiﬁed electricians. Life-threatening hazard and ﬁre

hazard from electric voltage of 230 V. Disconnect the mains power supply

prior to assembly / disassembly. No claim can be made under the warranty or

for liability in the event of damage due to incorrect connection.

> 2 x DIN ﬂush-mounted/surface boxes are required for the radio and speaker.

> It is possible to assemble the radio and speaker in a horizontal or vertical

position. When assembling the radio, ensure the correct position of the plug

contacts A for the radio display operating unit.

> The power supply is established via the terminal connections labelled L and N

on the back of the radio unit.

> The antenna must be connected to the terminal connection labelled

ANTENNA.

> Connect the speaker to the terminal connection B. Ensure correct polarity.

If the device is already mounted or assembled, remove the display operating

unit from the radio unit with the help of the frame. If the device is in

the delivery condition, remove the aachment from the radio unit using

your hands. Remove the aachment using your hands only. Under no

circumstances use a screwdriver or similar hard object for removal purposes.

When removing, you must ﬁrst of all overcome the resistance of the spring

snap-in clips.

+

-

A

B

A

> Aer successful assembly, ﬁrst of all connect the display operating unit taking

into account the position of the contact strip (A). To do so, carefully push the

display operating unit straight onto the radio unit until it engages.

More detailed installation instructions and illustrations can be found in section

„15 Installation“ auf Seite 27.

12

4 Description of the DIGITRADIO UP1

4.1 Scope of delivery

Before start-up, please check whether everything has been delivered.

1 x DIGITRADIO UP1

1 x instruction manual

1 x Dual Installation Frame

1 x Antenna

Aachment materials

4.2 The special features of the DIGITRADIO UP1

The DIGITRADIO UP1 is comprised of a DAB+/FM receiver with the following

functions:

- You can store up to 10 DAB+ and 10 FM stations.

- The radio receives on the FM 87.5–108 MHz (analogue) frequencies and

DAB+ 174.9–239.2 MHz (digital).

- The device has a time and date display.

- Alarm function and sleep timer

- Music playback via Bluetooth

5 General device functions

5.1 Switching on the device

> Press the /Mode buon to switch on the DIGITRADIO UP1.

Aer switching on for the ﬁrst time the device automatically performs a

complete scan in DAB mode. While scanning, the display information shows

the progress, as well as the number of digital radio stations detected. Aer

completing the station scan the ﬁrst DAB+ channel is played.

5.2 Switching o the device

> Keep the /Mode buon depressed to switch the device to standby mode.

[Standby] appears brieﬂy on the display. The date and time are shown on the

display. The display brightness in standby mode can be adjusted by following

the instructions in section 11.2.

5.3 Changing to DAB+/FM/Bluetooth mode

> Press the /Mode buon brieﬂy to switch between DAB+ (Digital Radio), FM

and Bluetooth.

5.4 Adjusting the volume

> Adjust the volume using the Vol +/- buons. The set volume is shown on the

display by way of a bar chart.

13

EN

FR

IT

NL

NW

DK

PL

CZ

SK

5.5 Retrieving displays

> Press the Info/Menu buon repeatedly to scroll through the information

available. You have the choice of viewing the following information:

In DAB+ mode (the selected function is identiﬁed with an “*”):

[Running text] (continuous text with additional information provided

by broadcasters etc.), [Signal intensity], [Channel type], [Ensemble],

[Frequency], [Signal quality], [Bit rate and Codec], [Time] and [Date].

In FM mode (the selected function is identiﬁed with an “*”):

[Radio text] (if transmied), [Channel type] (PTY), [Ps] (Programme Service

Name or Station Name or Frequency), [Audio Information], [Time] and [Date].

6 Menu operation

All the DIGITRADIO UP1 functions and seings are accessed via the menu. The menu

navigation takes place using the Info/Menu, <<, >> and Enter buons.

The menu is divided into submenus and, depending on the mode (DAB+ or FM),

contains dierent menu items or functions which can be enabled. To open the menu,

keep the Info/Menu buon depressed. To change to submenus, ﬁrst of all press the

<< or >> buons to display a submenu, then press the Enter buon to retrieve the

submenu. An asterisk (*) highlights the current selection.

Close menu: press the Info/Menu buon repeatedly (depending on which

submenu you are in), or wait until the current radio channel is displayed again.

Seings are not saved until the Enter buon is pressed. If the Info/Menu is

pressed instead, the seings are not conﬁrmed and saved (the Info/Menu

buon in this case acts as a “Back” buon).

The functions and buons to be pressed are shown in bold in this instruction

manual. Displays in [square brackets].

Some texts (e.g. menu items, station information) may be too long to show on

the display. Shortly thereaer, these will be shown as running text.

14

7 DAB+ (digital radio) function

7.1 What is DAB+?

DAB+ is a new digital format through which crystal clear sound with no noise can

be heard. In contrast to conventional analogue radio stations, DAB+ can be used to

broadcast multiple stations on one and the same frequency. This is referred to as

an ensemble or multiplex. An ensemble is comprised of the radio station, as well as

several service components or data services, which are broadcast individually by the

radio stations. There is information at www.digitalradio.de or www.digitalradio.ch, for

example.

7.1.1 Data compression

With this, digital radio takes advantage of the properties of human hearing. The

human ear does not perceive sounds which are found under a speciﬁc minimum

volume. Data which are found under the so-called audibility threshold can, therefore,

be ﬁltered out. This is possible because, in a digital data stream, the relevant relative

volume for other units is saved for every unit of information. Moreover, in an audio

signal, the quieter parts are superimposed by louder ones at a speciﬁc limit value.

All the sound information below the threshold of hearing in a piece of music can be

ﬁltered out of the signal to be broadcast. This leads to a reduction of data in the data

stream to be transmied, with no perceptible dierence in sound for the listener (HE

AAC v2 - supplementary codiﬁcation process for DAB+).

7.1.2 Audio stream

With digital radio, audio streams are continuous data streams which contain the

MPEG 1 audio layer 2 frames and thereby represent acoustic information. This

enables standard radio channels to be broadcast and listened to on the receiver

side. Digital radio provides you not only with excellent sound quality radio but also

additional information. This may refer to the programme being broadcast or be

independent information (e.g. news, weather, trac, tips).

7.2 DAB+ (digital radio) reception

> Brieﬂy press the /Mode buon until [Digital Radio] appears on the display.

If DAB+ is being started for the ﬁrst time, a complete scan will be performed.

Aer completing the scan, the ﬁrst station in alphanumerical order will be

played.

7.2.1 Performing a complete scan

The automatic scan [Complete Scan] scans all DAB+ band III channels and

thereby ﬁnds all stations being broadcast within the reception area.

Aer completing the scan, the ﬁrst station in alphanumerical order will be

played.

15

EN

FR

IT

NL

NW

DK

PL

CZ

SK

> In order to perform a complete scan, open the menu by keeping the Info/

Menu buon depressed and use the <<, >> and Enter buons to select the

menu item [Complete Scan].

> [Scan...] appears on the display.

During the scan a progress bar and the number of stations found is displayed.

7.2.2 Selecting stations

> In order to select DAB+ stations, open the station list by pressing the << or

>> buons. Conﬁrm the station selected with Enter. The selected station is

played.

7.2.3 Storing DAB+ stations on a memory slot

The programme memory can save up to 10 stations in the DAB+ range.

> Now select the desired station (see section 7.2.2).

> In order to store this station on a memory slot, keep the Preset buon

depressed while playing. Then use the <<, >> buons to select a station

memory slot (1-10). Press the Enter buon to save. [Station saved] appears

on the display.

> Repeat this process to save other stations.

7.2.4 Retrieving DAB+ stations from a memory slot

> To retrieve a station that you have stored in the FAV memory, brieﬂy press the

Preset buon and select a station slot (1-10) using the <<, >> buons. Press

the Enter buon to play the station.

If no station is saved on the selected station slot, [(empty)] appears on the

display.

7.2.5 Overwriting/deleting a station memory slot

> Simply save a new station to a favourite memory slot as described.

When retrieving the factory seings all memory slots are deleted.

16

7.2.6 Signal intensity

> Brieﬂy press the Info/Menu buon repeatedly until the signal intensity is

shown on the display by way of a bar chart.

Minimum signal intensity

Current signal intensity

Stations with a signal intensity below the required minimum signal intensity

are not transmiing a strong enough signal.

7.2.7 Manual seing

This menu item is used to check the reception channels and can be used to position

the antenna.

> Keep the Info/Menu buon depressed, use the << or >> buons to select the

[Manual Seing] item and press the Enter buon.

> Use the << or >> and Enter buons to select a channel (5A to 13F). The signal

intensity will now be shown on the display. If a DAB+ station is being received

on a channel, the station ensemble name is displayed.

Stations with a signal intensity below the required minimum signal intensity

are not transmiing a strong enough signal.

7.2.8 Volume adjustment (DRC)

With the Volume Adjustment menu item, the compression rate is set which balances

the dynamic variations and thereby the accompanying volume variations.

> Keep the Info/Menu buon depressed and use the << or >> buons to select

the item [Volume Adjustment].

> Press the Enter buon.

> Select the compression rate using the << or >> buons:

DRC high - High compression

DRC low - Low compression

DRC o - Compression switched o.

> Press the Enter buon to conﬁrm.

7.2.9 Deleting inactive stations

This menu item is for removing old stations and those no longer being received from

the station list.

> Keep the Info/Menu buon pressed and use the << or >> buons to select

the item [Delete Inactive Stations].

> Press the Enter buon.

This is followed by the prompt [Delete OK?], to check whether the inactive stations

are to be deleted.

> Using << or >>, select the [Yes] item and conﬁrm by pressing the Enter

buon.

17

EN

FR

IT

NL

NW

DK

PL

CZ

SK

8 FM mode

8.1 Switching on FM radio mode

> Brieﬂy press the /Mode buon until [FM] appears on the display.

When switching on for the ﬁrst time, the frequency 87.50 MHz is set.

If you have already set or saved a station, the radio plays the last station set.

In the case of RDS stations, the station name appears.

8.2 FM reception with RDS information

RDS is a procedure for broadcasting additional information via FM stations.

Broadcasters with RDS broadcast their station name or the programme type, for

example. This is shown on the display. The device can show the RDS information RT

(Radio text), PS (Station name), PTY (Programme type).

8.3 Automatic station scan

> Keep the << or >> buons depressed for longer (2 to 3 sec.), in order to

automatically search for the next station with sucient signal.

> Alternatively, you can press the Enter buon.

If a FM station with sucient signal intensity is found, the scan stops and the

station is played. If an RDS station is being received, the station name appears

and, possibly, radio text.

Please use the manual station scan for seing weaker stations.

8.4 Manual station scan

> Brieﬂy press the << or >> buons repeatedly to set the desired stations or

frequency.

The display shows the frequency in steps of 0.05 MHz.

8.5 Scan seing

In this menu item it is possible to set the sensitivity of the scan.

> Keep the Info/Menu depressed, use the << or >> buons to select the [Scan

Seing] item and press the Enter buon.

> Select whether the scan should only stop for stations with a strong signal

[Strong Stations Only] or for all stations (including stations with a weak

signal) [All Stations].

With the All Stations seing the scan stops automatically upon detecting

each available station. This can result in weak stations being played with

background noise.

18

8.6 Audio seings

> Keep the Info/Menu buon depressed and use the << or >> buons to select

the [Audio Seing] item.

> Press the Enter buon.

> Using the << or >> buons, select the item [Stereo possible] or [Mono only].

> Press the Enter buon to conﬁrm.

Given that the DIGITRADIO UP1 is a mono device, this seing only aects the

station reception intensity.

8.7 Saving FM stations to a memory slot

The station memory can save up to 10 stations in the FM range.

> First set the desired station frequency.

> In order to store this station on a memory slot, keep the Preset buon

depressed while playing. Then use the <<, >> buons to select a station

memory slot (1-10). Press the Enter buon to save.

> Repeat this process to save other stations.

8.8 Retrieving FM stations from a memory slot

> In order to retrieve a station that you have previously stored in the FAV

memory, brieﬂy press the Preset buon and use the <<, >> buons to select a

station memory slot (1-10). Press the Enter buon to play the station.

If you have no station saved to the selected station slot [(empty)] appears on

the display.

8.9 Overwriting/deleting a station memory slot

> Simply save a new station to the respective memory slot as described.

When retrieving the factory seings all memory slots are deleted.

9 Bluetooth

> Brieﬂy press the /Mode buon until [Bluetooth] is shown on the display.

If Bluetooth mode is being launched for the ﬁrst time, a playback device, e.g. a

smartphone or tablet, must be paired with the DIGITRADIO UP1.

If a playback device has already been paired once and it is located in the

reception range, it will be automatically connected.

19

EN

FR

IT

NL

NW

DK

PL

CZ

SK

9.1 Pairing a device

> Select Bluetooth mode on the DIGITRADIO UP1. The display shows [Bluetooth

Visible].

> Open the Bluetooth seings on the smartphone/tablet that you wish to pair

with the DIGITRADIO UP1.

> Launch the search for available Bluetooth devices.

> From the list of detected Bluetooth devices, select the DIGITRADIO UP 1 item.

> Once successfully paired, [Bluetooth Connected] appears on the display.

Please refer to the instruction manual for your smartphone/tablet as to how

to use the Bluetooth function on your smartphone/tablet.

9.2 Bluetooth playback

Once you have successfully paired your smartphone/tablet with the DIGITRADIO

UP1, you can start playing audio. Open a music app on your smartphone/tablet

and start playing music. Depending on the smartphone/tablet, the sound will either

be played directly via the DIGITRADIO UP1, or you will ﬁrst of all have to select the

DIGITRADIO UP1 as the playback device. Please refer to the instruction manual for

your smartphone/tablet as to how to select playback devices via Bluetooth on your

smartphone/tablet.

> To pause playback, press the Enter buon, or pause via the music app on your

smartphone/tablet. Press the buon again to continue playback.

> To skip to the next track, press the >> buon, or select the next track in the

music app on your smartphone/tablet.

> If you would like to listen to the track currently being played from the start,

press the << buon once. To skip to the previous track, press the << buon

twice. Alternatively, use the music app on your smartphone/tablet.

> The volume can be adjusted using the Vol+/- buons, or with the volume

control on your smartphone/tablet.

Control of the smartphone/tablet via the DIGITRADIO UP1 is only possible with

supported devices.

Depending on the smartphone/tablet, ring tones or system tones can also be

transferred.

20

La page est en cours de chargement...

TechniSat DigitRadio UP1 Le manuel du propriétaire

Ce manuel convient également à

TechniSat DigitRadio UP1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents