Tannoy CMS 503ICT LP Guide de démarrage rapide

Marque: Tannoy

Modèle: CMS 503ICT LP

Catégorie: Haut-parleurs de voiture

Taper: Guide de démarrage rapide

Quick Start Guide

CMS 3.0 Series

CMS803DC BM/PI/Q / CMS803 PI BACKCAN

8" Full Range Ceiling Loudspeaker with Dual Concentric Driver

CMS603DC BM/PI / CMS603ICT BM/PI/LS / CMS603 PI BACKCAN

6" Full Range Ceiling Loudspeaker with Dual Concentric or ICT Driver

CMS503DC BM/PI/LP / CMS503ICT BM/PI/LP / CMS503 PI BACKCAN

5" Full Range Ceiling Loudspeaker with Dual Concentric or ICT Driver

CMS403DCE / CMS403ICTE

4" Full Range Ceiling Loudspeaker with Dual Concentric or ICT Driver and adjustable “eyeball” design

2 CMS 3.0 Series Quick Start Guide 3

Instrucciones de

seguridad

NEGACIÓN LEGAL

GARANTÍA LIMITADA

Las terminales marcadas con este símbolo

transportan corriente eléctrica de

magnitud suciente como para constituir

un riesgo de descarga eléctrica. Utilice solo cables de

altavoz profesionales y de alta calidad con conectores

TS de 6,3 mm o de bayoneta prejados. Cualquier otra

instalación o modicación debe ser realizada únicamente

por un técnico cualicado.

Este símbolo, siempre que aparece,

leadvierte de la presencia de voltaje

peligroso sin aislar dentro de la caja;

estevoltaje puede ser suciente para constituir un riesgo

dedescarga.

Este símbolo, siempre que aparece,

leadvierte sobre instrucciones operativas

y de mantenimiento que aparecen en la

documentación adjunta. Por favor, lea el manual.

Atención

Para reducir el riesgo de descarga

eléctrica, no quite la tapa (o la parte

posterior). No hay piezas en el interior del equipo que

puedan ser reparadas por el usuario. Si es necesario,

póngase en contacto con personal cualicado.

Atención

Para reducir el riesgo de incendio o

descarga eléctrica, no exponga este

aparato a la lluvia, humedad o alguna otra fuente que

pueda salpicar o derramar algún líquido sobre el aparato.

Nocoloque ningún tipo de recipiente para líquidos sobre

el aparato.

Atención

Las instrucciones de servicio deben

llevarlas a cabo exclusivamente personal

cualicado. Para evitar el riesgo de una descarga eléctrica,

no realice reparaciones que no se encuentren descritas

en el manual de operaciones. Lasreparaciones deben ser

realizadas exclusivamente por personalcualicado.

1. Lea las instrucciones.

2. Conserve estas instrucciones.

3. Preste atención a todas las advertencias.

4. Siga todas las instrucciones.

5. No use este aparato cerca del agua.

6. Limpie este aparato con un paño seco.

7. No bloquee las aberturas de ventilación. Instale el

equipo de acuerdo con las instrucciones del fabricante.

8. No instale este equipo cerca de fuentes de calor

tales como radiadores, acumuladores de calor, estufas u

otros aparatos (incluyendo amplicadores) que puedan

producir calor.

9. No elimine o deshabilite nunca la conexión a tierra

del aparato o del cable de alimentación de corriente.

Unenchufe polarizado tiene dos polos, uno de los cuales

tiene un contacto más ancho que el otro. Una clavija con

puesta a tierra dispone de tres contactos: dos polos y la

puesta a tierra. El contacto ancho y el tercer contacto,

respectivamente, son los que garantizan una mayor

seguridad. Si el enchufe suministrado con el equipo no

concuerda con la toma de corriente, consulte con un

electricista para cambiar la toma de corriente obsoleta.

10. Coloque el cable de suministro de energía de manera

que no pueda ser pisado y que esté protegido de objetos

alados. Asegúrese de que el cable de suministro de

energía esté protegido, especialmente en la zona de la

clavija y en el punto donde sale del aparato.

11. Use únicamente los dispositivos o accesorios

especicados por el fabricante.

12. Use únicamente la

carretilla, plataforma,

trípode, soporte o mesa

especicados por el

fabricante o suministrados

junto con el equipo.

Altransportar el equipo,

tenga cuidado para evitar

daños y caídas al tropezar con algún obstáculo.

13. Desenchufe el equipo durante tormentas o si no va a

utilizarlo durante un periodo largo.

14. Confíe las reparaciones únicamente a servicios

técnicos cualicados. La unidad requiere mantenimiento

siempre que haya sufrido algún daño, si el cable de

suministro de energía o el enchufe presentaran daños,

sehubiera derramado un líquido o hubieran caído objetos

dentro del equipo, si el aparato hubiera estado expuesto

a la humedad o la lluvia, si ha dejado de funcionar de

manera normal o si ha sufrido algún golpe o caída.

15. Al conectar la unidad a la toma de corriente eléctrica

asegúrese de que la conexión disponga de una unión

atierra.

16. Si el enchufe o conector de red sirve como único

medio de desconexión, éste debe ser accesiblefácilmente.

17. Cómo debe deshacerse de

este aparato: Este símbolo indica

que este aparato no debe ser

tratado como basura orgánica,

según lo indicado en la Directiva

WEEE (2012/19/EU) y a las

normativas aplicables en su país.

En lugar de ello deberá llevarlo al punto limpio más

cercano para el reciclaje de sus elementos eléctricos/

electrónicos (EEE). Al hacer esto estará ayudando a

prevenir las posibles consecuencias negativas para el

medio ambiente y la salud que podrían ser provocadas por

una gestión inadecuada de este tipo de aparatos. Además,

el reciclaje de materiales ayudará a conservar los recursos

naturales. Para más información acerca del reciclaje de

este aparato, póngase en contacto con el Ayuntamiento

de su ciudad o con el punto limpio local.

18. No instale esta unidad en un espacio muy reducido,

tal como encastrada en una librería o similar.

19. No coloque objetos con llama, como una vela

encendida, sobre este aparato.

20. Tenga presentes todas las advertencias relativas

al reciclaje y correcta eliminación de las pilas. Las pilas

deben ser siempre eliminadas en un punto limpio y nunca

con el resto de la basura orgánica.

21. Use este aparato en rangos de temperatura

moderados y/o tropicales.

Music Tribe no admite ningún tipo de responsabilidad

por cualquier daño o pérdida que pudiera sufrir

cualquier persona por conar total o parcialmente en

la descripciones, fotografías o armaciones contenidas

en este documento. Las especicaciones técnicas,

imágenes y otras informaciones contenidas en este

documento están sujetas a modicaciones sin previo

aviso. Todas las marcas comerciales que aparecen

aquí son propiedad de sus respectivos dueños. Midas,

Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound,

TC Electronic, TC Helicon, Behringer, Bugera y Coolaudio

son marcas comerciales o marcas registradas de

Music Tribe Global Brands Ltd. © Music Tribe Global

Brands Ltd. 2018 Reservados todos los derechos.

Si quiere conocer los detalles y condiciones aplicables

de la garantía así como información adicional sobre la

Garantía limitada de Music Tribe, consulte online toda la

información en la web musictribe.com/warranty.

Terminals marked with this symbol carry

electrical current of sucient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modication should be performed only

by qualiedpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be sucient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

qualied personnel.

Caution

To reduce the risk of re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by qualied service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by qualied

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories specied by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table specied by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualied service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

17. Correct disposal of this

product: This symbol indicates that

this product must not be disposed

of with household waste,

according to the WEEE Directive

(2012/19/EU) and your national

law. This product should be taken

to a collection center licensed for the recycling of waste

electrical and electronic equipment (EEE). The

mishandling of this type of waste could have a possible

negative impact on the environment and human health

due to potentially hazardous substances that are generally

associated with EEE. At the same time, your cooperation

in the correct disposal of this product will contribute to

the ecient use of natural resources. For more

information about where you can take your waste

equipment for recycling, please contact your local city

oce, or your household waste collection service.

18. Do not install in a conned space, such as a book

case or similar unit.

19. Do not place naked ame sources, such as lighted

candles, on the apparatus.

20. Please keep the environmental aspects of battery

disposal in mind. Batteries must be disposed-of at a

battery collection point.

21. Use this apparatus in tropical and/or

moderate climates.

Music Tribe accepts no liability for any loss which

may be suered by any person who relies either

wholly or in part upon any description, photograph,

or statement contained herein. Technical specications,

appearances and other information are subject to

change without notice. All trademarks are the property

of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic,

TC Helicon, Behringer, Bugera and Coolaudio are

trademarks or registered trademarks of Music Tribe

Global Brands Ltd. © Music Tribe Global Brands Ltd.

For the applicable warranty terms and conditions

and additional information regarding Music Tribe’s

Limited Warranty, please see complete details online at

musictribe.com/warranty.

Zhongshan Eurotec Electronics Limited

No. 10 Wanmei Road, South China Modern Chinese

Medicine Park, Nanlang Town, 528451, Zhongshan City,

Guangdong Province, China

Important Safety

Instructions

LEGAL DISCLAIMER

LIMITED WARRANTY

4 CMS 3.0 Series Quick Start Guide 5

Consignes de sécurité

DÉNI LÉGAL

GARANTIE LIMITÉE

Wichtige

Sicherheitshinweise

HAFTUNGSAUSSCHLUSS

BESCHRÄNKTE GARANTIE

Les points repérés par ce symbole portent

une tension électrique susante pour

constituer un risque d’électrocution.

Utilisez uniquement des câbles d’enceintes professionnels

de haute qualité avec ches Jack mono 6,35 mm ou ches

à verrouillages déjà installées. Touteautre installation ou

modication doit être eectuée uniquement par un

personnel qualié.

Ce symbole avertit de la présence d’une

tension dangereuse et non isolée à

l’intérieur de l’appareil - elle peut

provoquer des chocs électriques.

Attention

Ce symbol signale les consignes

d’utilisation et d’entre ! Tien importantes

dans la documentation fournie. Lisez les consignes de

sécurité du manuel d’utilisation de l’appareil.

Attention

Pour éviter tout risque de choc électrique,

ne pas ouvrir le capot de l’appareil ni

démonter le panneau arrière. L’intérieur de l’appareil

ne possède aucun élément réparable par l’utilisateur.

Laissertoute réparation à un professionnel qualié.

Attention

Pour réduire les risques de feu et de choc

électrique, n’exposez pas cet appareil à la

pluie, à la moisissure, aux gouttes ou aux éclaboussures.

Ne posez pas de récipient contenant un liquide sur

l’appareil (un vase par exemple).

Attention

Ces consignes de sécurité et d’entretien

sont destinées à un personnel qualié.

Pouréviter tout risque de choc électrique, n’eectuez

aucune réparation sur l’appareil qui ne soit décrite par le

manuel d’utilisation. Les éventuelles réparations doivent

être eectuées uniquement par un technicien spécialisé.

1. Lisez ces consignes.

2. Conservez ces consignes.

3. Respectez tous les avertissements.

4. Respectez toutes les consignes d’utilisation.

5. N’utilisez jamais l’appareil à proximité d’un liquide.

6. Nettoyez l’appareil avec un chion sec.

7. Veillez à ne pas empêcher la bonne ventilation de

l’appareil via ses ouïes de ventilation. Respectezles

consignes du fabricant concernant l’installation

del’appareil.

8. Ne placez pas l’appareil à proximité d’une source

de chaleur telle qu’un chauage, une cuisinière ou tout

appareil dégageant de la chaleur (y compris un ampli

depuissance).

9. Ne supprimez jamais la sécurité des prises bipolaires

ou des prises terre. Les prises bipolaires possèdent deux

contacts de largeur diérente. Leplus large est le contact

de sécurité. Les prises terre possèdent deux contacts plus

une mise à la terre servant de sécurité. Si la prise du bloc

d’alimentation ou du cordon d’ali-mentation fourni ne

correspond pas à celles de votre installation électrique,

faites appel à un électricien pour eectuer le changement

de prise.

10. Installez le cordon d’alimentation de telle façon

que personne ne puisse marcher dessus et qu’il soit

protégé d’arêtes coupantes. Assurez-vous que le cordon

d’alimentation est sufsamment protégé, notamment au

niveau de sa prise électrique et de l’endroit où il est relié à

l’appareil; cela est également valable pour une éventuelle

rallonge électrique.

11. Utilisez exclusivement des accessoires et des

appareils supplémentaires recommandés par lefabricant.

12. Utilisez

exclusivement des

chariots, des diables,

desprésentoirs, despieds

et des surfaces de

travail recommandés

par le fabricant ou

livrés avec le produit.

Déplacezprécautionneusement tout chariot ou diable

chargé pour éviter d’éventuelles blessures en cas dechute.

13. Débranchez l’appareil de la tension secteur en cas

d’orage ou si l’appareil reste inutilisé pendant une longue

période de temps.

14. Les travaux d’entretien de l’appareil doivent

être eectués uniquement par du personnel qualié.

Aucunentretien n’est nécessaire sauf si l’appareil est

endommagé de quelque façon que ce soit (dommagessur

le cordon d’alimentation ou la prise par exemple), siun

liquide ou un objet a pénétré à l’intérieur du châssis,

si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne

fonctionne pas correctement ou à la suite d’une chute.

15. L’appareil doit être connecté à une prise secteur

dotée d’une protection par mise à la terre.

16. La prise électrique ou la prise IEC de tout appareil

dénué de bouton marche/arrêt doit rester accessible

enpermanence.

17. Mise au rebut appropriée de

ce produit: Ce symbole indique

qu’en accord avec la directive DEEE

(2012/19/EU) et les lois en vigueur

dans votre pays, ce produit ne doit

pas être jeté avec les déchets

ménagers. Ce produit doit être

déposé dans un point de collecte agréé pour le recyclage

des déchets d’équipements électriques et électroniques

(EEE). Une mauvaise manipulation de ce type de déchets

pourrait avoir un impact négatif sur l’environnement et la

santé à cause des substances potentiellement

dangereuses généralement associées à ces équipements.

En même temps, votre coopération dans la mise au rebut

de ce produit contribuera à l’utilisation ecace des

ressources naturelles. Pour plus d’informations sur

l’endroit où vous pouvez déposer vos déchets

d’équipements pour le recyclage, veuillez contacter votre

mairie ou votre centre local de collecte des déchets.

18. N’installez pas l’appareil dans un espace conné tel

qu’une bibliothèque ou meuble similaire.

19. Ne placez jamais d’objets enammés, tels que des

bougies allumées, sur l’appareil.

20. Gardez à l’esprit l’impact environnemental lorsque

vous mettez des piles au rebus. Les piles usées doivent

être déposées dans un point de collecte adapté.

21. Utilisez l’appareil dans un climat tropical

et/ou modéré.

Music Tribe ne peut être tenu pour responsable pour

toute perte pouvant être subie par toute personne

se ant en partie ou en totalité à toute description,

photographie ou armation contenue dans ce

document. Les caractéristiques, l’apparence et d’autres

informations peuvent faire l’objet de modications

sans notication. Toutes les marques appartiennent

à leurs propriétaires respectifs. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic,

TC Helicon, Behringer, Bugera et Coolaudio sont

des marques ou marques déposées de Music Tribe

Global Brands Ltd. © Music Tribe Global Brands Ltd.

Pour connaître les termes et conditions de garantie

applicables, ainsi que les informations supplémentaires

et détaillées sur la Garantie Limitée de Music Tribe,

consultez le site Internet musictribe.com/warranty.

Vorsicht

Die mit dem Symbol markierten

Anschlüsse führen so viel Spannung,

dassdie Gefahr eines Stromschlags besteht.

Verwenden Sie nur hochwertige, professionelle

Lautsprecherkabel mit vorinstallierten 6,35 mm

MONO-Klinkensteckern oder Lautsprecherstecker

mit Drehverriegelung. Alle anderen Installationen

oder Modikationen sollten nur von qualiziertem

Fachpersonal ausgeführt werden.

Achtung

Um eine Gefährdung durch Stromschlag

auszuschließen, darf die Geräteabdeckung

bzw. Geräterückwand nicht abgenommen werden.

ImInnern des Geräts benden sich keine vom Benutzer

reparierbaren Teile. Reparaturarbeiten dürfen nur von

qualiziertem Personal ausgeführt werden.

Achtung

Um eine Gefährdung durch Feuer bzw.

Stromschlag auszuschließen, darf dieses

Gerät weder Regen oder Feuchtigkeit ausgesetzt werden

noch sollten Spritzwasser oder tropfende Flüssigkeiten

in das Gerät gelangen können. Stellen Sie keine mit

Flüssigkeit gefüllten Gegenstände, wie z. B. Vasen,

aufdasGerät.

Achtung

Die Service-Hinweise sind nur durch

qualiziertes Personal zu befolgen.

Umeine Gefährdung durch Stromschlag zu vermeiden,

führen Sie bitte keinerlei Reparaturen an dem Gerät

durch, die nicht in der Bedienungsanleitung beschrieben

sind. Reparaturen sind nur von qualiziertem

Fachpersonaldurchzuführen.

1. Lesen Sie diese Hinweise.

2. Bewahren Sie diese Hinweise auf.

3. Beachten Sie alle Warnhinweise.

4. Befolgen Sie alle Bedienungshinweise.

5. Betreiben Sie das Gerät nicht in der Nähe vonWasser.

6. Reinigen Sie das Gerät mit einem trockenen Tuch.

7. Blockieren Sie nicht die Belüftungsschlitze. Beachten

Sie beim Einbau des Gerätes die Herstellerhinweise.

8. Stellen Sie das Gerät nicht in der Nähe von

Wärmequellen auf. Solche Wärmequellen sind z. B.

Heizkörper, Herde oder andere Wärme erzeugende Geräte

(auch Verstärker).

9. Entfernen Sie in keinem Fall die

Sicherheitsvorrichtung von Zweipol- oder geerdeten

Steckern. Ein Zweipolstecker hat zwei unterschiedlich

breite Steckkontakte. Ein geerdeter Stecker hat zwei

Steckkontakte und einen dritten Erdungskontakt.

Derbreitere Steckkontakt oder der zusätzliche

Erdungskontakt dient Ihrer Sicherheit. Falls das

mitgelieferte Steckerformat nicht zu Ihrer Steckdose

passt, wenden Sie sich bitte an einen Elektriker, damit die

Steckdose entsprechend ausgetauscht wird.

10. Verlegen Sie das Netzkabel so, dass es vor

Tritten und scharfen Kanten geschützt ist und nicht

beschädigt werden kann. Achten Sie bitte insbesondere

im Bereich der Stecker, Verlängerungskabel und an

der Stelle, an der das Netzkabel das Gerät verlässt,

aufausreichendenSchutz.

11. Das Gerät muss jederzeit mit intaktem Schutzleiter

an das Stromnetz angeschlossen sein.

12. Sollte der Hauptnetzstecker oder eine

Gerätesteckdose die Funktionseinheit zum Abschalten

sein, muss diese immer zugänglich sein.

13. Verwenden Sie nur Zusatzgeräte/Zubehörteile,

dielaut Hersteller geeignet sind.

14. Verwenden

Sie nur Wagen,

Standvorrichtungen,

Stative, Halter oder Tische,

die vom Hersteller benannt

oder im Lieferumfang

des Geräts enthalten

sind. Falls Sie einen

Wagen benutzen, seien Sie vorsichtig beim Bewegen

der Wagen- Gerätkombination, umVerletzungen durch

Stolpern zuvermeiden.

15. Ziehen Sie den Netzstecker bei Gewitter oder wenn

Sie das Gerät längere Zeit nicht benutzen.

16. Lassen Sie alle Wartungsarbeiten nur von

qualiziertem Service-Personal ausführen. EineWartung

ist notwendig, wenn das Gerät in irgendeiner Weise

beschädigt wurde (z. B. Beschädigung des Netzkabels oder

Steckers), Gegenstände oder Flüssigkeit in das Geräteinnere

gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt

wurde, das Gerät nicht ordnungsgemäß funktioniert oder

auf den Boden gefallen ist.

17. Korrekte Entsorgung dieses

Produkts: Dieses Symbol weist

darauf hin, das Produkt

entsprechend der WEEE Direktive

(2012/19/EU) und der jeweiligen

nationalen Gesetze nicht

zusammen mit Ihren

Haushaltsabfällen zu entsorgen. DiesesProdukt sollte bei

einer autorisierten Sammelstelle für Recycling elektrischer

und elektronischer Geräte (EEE) abgegeben werden.

Wegen bedenklicher Substanzen, diegenerell mit

elektrischen und elektronischen Geräten in Verbindung

stehen, könnte eine unsachgemäße Behandlung dieser

Abfallart eine negative Auswirkung auf Umwelt und

Gesundheit haben. Gleichzeitig gewährleistet Ihr Beitrag

zur richtigen Entsorgung dieses Produkts die eektive

Nutzung natürlicher Ressourcen. Fürweitere

Informationen zur Entsorgung Ihrer Geräte bei einer

Recycling-Stelle nehmen Sie bitte Kontakt zum

zuständigen städtischen Büro, Entsorgungsamt oder zu

Ihrem Haushaltsabfallentsorgerauf.

18. Installieren Sie das Gerät nicht in einer beengten

Umgebung, zum Beispiel Bücherregal oder ähnliches.

19. Stellen Sie keine Gegenstände mit oenen

Flammen, etwa brennende Kerzen, auf das Gerät.

20. Beachten Sie bei der Entsorgung von Batterien

den Umweltschutz-Aspekt. Batterien müssen bei einer

Batterie-Sammelstelle entsorgt werden.

21. Verwenden Sie das Gerät in tropischen und/oder

gemäßigten Klimazonen.

Music Tribe übernimmt keine Haftung für Verluste,

die Personen entstanden sind, die sich ganz oder

teilweise auf hier enthaltene Beschreibungen,

Fotos oder Aussagen verlassen haben. Technische Daten,

Erscheinungsbild und andere Informationen können

ohne vorherige Ankündigung geändert werden.

Alle Warenzeichen sind Eigentum der jeweiligen

Inhaber. Midas, Klark Teknik, Lab Gruppen, Lake,

Tannoy, Turbosound, TC Electronic, TC Helicon,

Behringer, Bugera und Coolaudio sind Warenzeichen

oder eingetragene Warenzeichen der Music Tribe

Global Brands Ltd. © Music Tribe Global Brands Ltd.

Die geltenden Garantiebedingungen und zusätzliche

Informationen bezüglich der von Music Tribe gewährten

beschränkten Garantie nden Sie online unter

musictribe.com/warranty.

6 CMS 3.0 Series Quick Start Guide 7

Instruções de Segurança

Importantes

LEGAL RENUNCIANTE

GARANTIA LIMITADA

Aviso!

Terminais marcados com o símbolo

carregam corrente elétrica de magnitude

suciente para constituir um risco de choque elétrico.

Use apenas cabos de alto-falantes de alta qualidade

com plugues TS de ¼" ou plugues com trava de torção

pré-instalados. Todas as outras instalações e modicações

devem ser efetuadas por pessoasqualicadas.

Este símbolo, onde quer que o encontre,

alerta-o para a leitura das instruções de

manuseamento que acompanham o

equipamento. Por favor leia o manual de instruções.

Atenção

De forma a diminuir o risco de choque

eléctrico, não remover a cobertura

(ouasecção de trás). Não existem peças substituíveis por

parte do utilizador no seu interior. Para esse efeito recorrer

a um técnico qualicado.

Atenção

Para reduzir o risco de incêndios ou

choques eléctricos o aparelho não deve ser

exposto à chuva nem à humidade. Além disso, não deve

ser sujeito a salpicos, nem devem ser colocados em cima

do aparelho objectos contendo líquidos, tais como jarras.

Atenção

Estas instruções de operação devem ser

utilizadas, em exclusivo, por técnicos de

assistência qualicados. Para evitar choques eléctricos

não proceda a reparações ou intervenções, que não as

indicadas nas instruções de operação, salvo se possuir as

quali-cações necessárias. Para evitar choques eléctricos

não proceda a reparações ou intervenções, que não as

indicadas nas instruções de operação. Só o deverá fazer se

possuir as qualicações necessárias.

1. Leia estas instruções.

2. Guarde estas instruções.

3. Preste atenção a todos os avisos.

4. Siga todas as instruções.

5. Não utilize este dispositivo perto de água.

6. Limpe apenas com um pano seco.

7. Não obstrua as entradas de ventilação. Instale de

acordo com as instruções do fabricante.

8. Não instale perto de quaisquer fontes de calor

tais como radiadores, bocas de ar quente, fogões de

sala ou outros aparelhos (incluindo amplicadores)

que produzam calor.

9. Não anule o objectivo de segurança das chas

polarizadas ou do tipo de ligação à terra. Uma cha

polarizada dispõe de duas palhetas sendo uma mais larga

do que a outra. Uma cha do tipo ligação à terra dispõe

de duas palhetas e um terceiro dente de ligação à terra.

A palheta larga ou o terceiro dente são fornecidos para

sua segurança. Se a cha fornecida não encaixar na sua

tomada, consulte um electricista para a substituição da

tomada obsoleta.

10. Proteja o cabo de alimentação de pisadelas ou

apertos, especialmente nas chas, extensões, e no local

de saída da unidade. Certique-se de que o cabo eléctrico

está protegido. Verique particularmente nas chas, nos

receptáculos e no ponto em que o cabo sai doaparelho.

11. O aparelho tem de estar sempre conectado à rede

eléctrica com o condutor de protecção intacto.

12. Se utilizar uma cha de rede principal ou uma

tomada de aparelhos para desligar a unidade de

funcionamento, esta deve estar sempre acessível.

13. Utilize apenas ligações/acessórios especicados

pelofabricante.

14. Utilize apenas com

o carrinho, estrutura,

tripé, suporte, ou mesa

especicados pelo

fabricante ou vendidos

com o dispositivo.

Quandoutilizar um

carrinho, tenha cuidado ao

mover o conjunto carrinho/dispositivo para evitar danos

provocados pela terpidação.

15. Desligue este dispositivo durante as trovoadas

ou quando não for utilizado durante longos períodos

detempo.

16. Qualquer tipo de reparação deve ser sempre

efectuado por pessoal qualicado. É necessária uma

reparação sempre que a unidade tiver sido de alguma

forma danicada, como por exemplo: no caso do cabo

de alimentação ou cha se encontrarem danicados;

naeventualidade de líquido ter sido derramado ou

objectos terem caído para dentro do dispositivo; no caso

da unidade ter estado exposta à chuva ou à humidade;

seesta não funcionar normalmente, ou se tiver caído.

17. Correcta eliminação deste

produto: este símbolo indica que

o produto não deve ser eliminado

juntamente com os resíduos

domésticos, segundo a Directiva

REEE (2012/19/EU) e a legislação

nacional. Este produto deverá

ser levado para um centro de recolha licenciado para a

reciclagem de resíduos de equipamentos eléctricos e

electrónicos (EEE). O tratamento incorrecto deste tipo

de resíduos pode ter um eventual impacto negativo

no ambiente e na saúde humana devido a substâncias

potencialmente perigosas que estão geralmente

associadas aos EEE. Ao mesmo tempo, a sua colaboração

para a eliminação correcta deste produto irá contribuir

para a utilização eciente dos recursos naturais. Paramais

informação acerca dos locais onde poderá deixar o seu

equipamento usado para reciclagem, é favor contactar

os serviços municipais locais, a entidade de gestão de

resíduos ou os serviços de recolha de resíduosdomésticos.

18. Não instale em lugares connados, tais como

estantes ou unidades similares.

19. Não coloque fontes de chama, tais como velas

acesas, sobre o aparelho.

20. Favor, obedecer os aspectos ambientais de descarte

de bateria. Baterias devem ser descartadas em um ponto

de coletas de baterias.

21. Use este aparelho em climas tropicais

e/ou moderados.

O Music Tribe não se responsabiliza por perda alguma

que possa ser sofrida por qualquer pessoa que dependa,

seja de maneira completa ou parcial, de qualquer

descrição, fotograa, ou declaração aqui contidas.

Dados técnicos, aparências e outras informações estão

sujeitas a modicações sem aviso prévio. Todas as

marcas são propriedade de seus respectivos donos.

Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy,

Turbosound, TC Electronic, TC Helicon, Behringer,

Bugera e Coolaudio são marcas ou marcas registradas

do Music Tribe Global Brands Ltd. © Music Tribe Global

Para obter os termos de garantia aplicáveis e condições e

informações adicionais a respeito da garantia limitada do

Music Tribe, favor vericar detalhes na íntegra através do

website musictribe.com/warranty.

Introduction

Thank you for purchasing this TANNOY Ceiling Monitor System product. Designed for both speech and music program material, the TANNOY CMS range provides

exceptional sonic quality and long-term reliability in all ceiling mount applications. The CMS 3.0 DC series features new 16 ohm Dual Concentric drivers for improved

performance and prolonged service life.

Unpacking

Every TANNOY product is carefully inspected before shipment. After unpacking, please inspect your product to ensure no damage has occurred in transit. In the

unlikely event of damage, please notify your dealer and retain all shipping materials as your dealer may require return shipment.

All CMS loudspeakers are shipped in pairs and provided with the following accessories as standard: C-ring, tile-bridge kit, cut-out template and paint mask. A plaster

(mud) ring is available as an optional accessory.

Safety Notices

Some regional construction codes require the use of a secondary method of securing loudspeakers in the ceiling to provide security of a backup support. A secondary

support line should be attached from the safety loop on the rear of the product to a source point on the ceiling. For PI models, the secondary support line should be

attached from the back of the driver chassis to a source point on the ceiling. Please consult the relevant construction codes in your region.

When using a power driver to install the product, it is essential to use the correct torque level settings to avoid over-tightening and damage to the ceiling material or

clamps. Recommended torque setting: 1.5 Nm

TANNOY will not be held responsible for any damages caused by the improper installation of these loudspeakers.

The CMS 603 ICT LS is UL-1480, category UUMW, for use with non-DC supervised systems.

Electrical Safety Notice: To comply with the standard UL-1480, metal-clad flexible conduit (BX) is required for connection to the terminal block for proper

earth grounding.

In order to comply with UL regulations, the PI backcan must always be used with the CMS PI models.

SAFETY NOTE:

In order to comply with the relevant  re safety regulations (ie. BS 5839:1998), it is required that in the event of  re, that failure of the circuit to which the loudspeaker is connected does not occur before evacuation of the building is complete. Suitable measures include: - a) use

of terminal blocks (for connection to primary) with a melting point of not less than 650°C, for example constructed from ceramic materials; b) use of terminal blocks of a lower melting point but protected with thermal insulation;c) use of terminal blocks such that, on melting, an

open-circuit or a short-circuit does not occur.

8 CMS 3.0 Series Quick Start Guide 9

Product Feature Identi cation

IMPORTANT NOTE: Drawings for each loudspeaker below are generic and apply to the loudspeaker types specified. Some variations will be apparent in some models,

but differences are not critical for installation purposes except as noted.

Blind Mount

The blind-mount models are supplied with a pre-fitted backcan. Above applies to all models as well any others that do NOT have a “PI” suffix.

Pre-install

A pre-install (PI) unit is shown without the optional pre-install backcan.

Pre-install backcan

Optional pre-install (PI) backcan for PI models.

NOTE: The CMS 603DC/ICT and CMS 803DC models have the transformer pre-attached to the inside of the backcan. The CMS 503DC/ICT has the transformer

pre-attached to the loudspeaker assembly.

Accessories

Standard Accessories

Optional Accessories

C-Ring

Grille

Paint Mask

Cut-out template

Tile-bridge kit

Note: A tile-bridge kit

must always be used

when installing into

suspended ceiling tiles

60 W Transformer

Note: For use with CMS

803 PI in distributed lines

without backcans.

Plaster (mud) ring

10 CMS 3.0 Series Quick Start Guide 11

Installation Guide for Suspended Ceilings

1. Remove the ceiling tile from its frame and place it on a  at surface. Position the cutout template

(self adhesive backed) on the tile. (Fig.1)

2. Cut out the hole in the ceiling tile using a pad saw following the broken line indicated on the template (Fig.2)

3. Place the C-Ring and tile-bridge on top of the ceiling panel, aligning the C-Ring over the hole, and screw the

C-Ring to the tile bridge using the  xings provided. (Fig.3)

4. Go to the ‘Wiring and Setting Up’ chapter.

5. Slide the speaker assembly through the hole. Turn the screws (denoted “Screw Fix”) clockwise on the front

of the speaker to extend the mounting wings. Tighten the screws until a  rm grip is achieved. (NOTE: Screws

have a PoziDriv head; use of a PoziDriv driver is recommended). If using a power driver,

TANNOY

recommends a

torque setting of 1.5 Nm. (Fig.4)

DO NOT OVERTIGHTEN!

6. Attach the nylon safety to the hooks on the front ba e before attaching the grille by presenting it to the

speakers and allowing the magnets to pull it into position (Fig.5). (With the CMS 403DCe/ICTe, the grille is

already  tted to the product.)

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step 5, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front

trim to conceal the mounting screws.

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Installation Guide for Sheetrock (Plasterboard) Ceilings

1. Position the cutout template (self adhesive backed) on the ceiling. (Fig.1)

2. Cut out the hole in the ceiling using a pad saw following the broken line indicated on the template then slide the

C-Ring into the ceiling, aligning it over the cut-out hole. (Fig.2)

3. Go to the ‘Wiring and Setting Up’ chapter, then return to point 4 below.

4. Slide the speaker assembly through the hole. Turn the screws (denoted “Screw Fix”) clockwise on the front of

the speaker to extend the mounting wings. Tighten the screws until a  rm grip is achieved. (NOTE: Screws have

a PoziDriv head; use of a PoziDriv driver is recommended). If using a power driver,

TANNOY

recommends a torque

setting of 1.5 Nm. (Fig.3)

DO NOT OVERTIGHTEN!

5. Attach the nylon safety to the hooks on the front ba e before attaching the grille by presenting it to the speakers

and allowing the magnets to pull it into position (Fig.4). (With the CMS 403DCe/ICTe, the grille is already  tted to

the product.)

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step 4, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front

trim to conceal the mounting screws.

Fig.1

Fig.2

Fig.3

Fig.4

12 CMS 3.0 Series Quick Start Guide 13

Installation Guide for Optional Plaster Ring

An optional plaster (mud) ring bracket is available from TANNOY. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings.

1. Nail or screw the plaster ring to the joists. (Fig.1)

2. Lay the speaker wiring to where the speaker will be  tted and complete the plastering work on the ceiling. (Fig.2)

3. Go to the ‘Wiring and Setting Up’ chapter, then return to point 4 below.

4. Slide the speaker assembly through the hole. Turn the screws (denoted “Screw Fix”) clockwise on the front of

the speaker to extend the mounting wings. Tighten the screws until a  rm grip is achieved. (Note: Screws have a

PoziDriv head; use of a PoziDriv driver is recommended). If using a power driver,

TANNOY

recommends a torque

setting of 1.5 Nm. (Fig.3)

DO NOT OVERTIGHTEN!

5. Attach the nylon safety to the hooks on the front ba e before attaching the grille by presenting it to the speakers

and allowing the magnets to pull it into position (Fig.4). (With the CMS 403DCe/ICTe, the grille is already  tted to

the product.)

NOTE ON INSTALLATION OF CMS 403DCe/ICTe:

Before tightening the screws in step 4, swivel the speaker in the desired direction. When the screws are tightened, the speaker will lock into position. Replace the front

trim to conceal the mounting screws.

Fig.1

Fig.2

Fig.3

Fig.4

Installation Guide for Optional Pre-Installation Backcan (PI Models Only)

An optional pre-install backcan is available for all pre-install (PI) models. The backcan is designed for pre-installation in newly constructed, non-suspended ceilings.

NOTE: The CMS 603DC/ICT and CMS 803DC models have the transformer pre-attached to the inside of the backcan; the CMS 503DC/ICT models have the transformer

pre-attached to the loudspeaker assembly.

1. Attach the backcan to a safe and secure  xing point. This can be done in a number of ways:

METHOD 1: Fix the backcan to a secure fixing point by using suitable fixings with the 4 fixing holes provided

on the PI backcan. (Fig.1)

METHOD 2: Secure the backcan to a safe and secure fixing point using suitable fixings with the flexible straps

that are attached to the PI backcan. (Fig.2)

METHOD 3:

a. Attach the PI backcan to the optional pre-mount ring (plaster ring) using the fixings provided with the

pre-mount ring. (Fig.3)

b. Next, secure the wings of the pre-mount ring to a safe and secure fixing point by using suitable

fixings. (Fig.4)

Please turn over

Fig.1

Fig.2

Fig.3

Fig.4

14 CMS 3.0 Series Quick Start Guide 15

Installation Guide for Optional Pre-Installation Backcan (PI Models Only)

2. Attach the conduit to the installed backcan. This can be done in two ways:

METHOD 1: You can use the clamp at the back of the pre-install backcan. The product will accept a

squeeze connector with a thread size of up to 22 mm: To remove the cable clamp, simply unscrew

the threaded washer (under the wiring cover) which holds the cable clamp in place and replace it

with a conduit squeeze connector. (Fig.5)

METHOD 2: You can use any of the three knock-out points at the sides of the PI backcan

(19 mm, 22 mm or 28 mm diameter). (Fig.6)

3. If conduit is not chosen as the wiring method, run an approved speaker cable to the installed can.

Terminate in the top mounted cable clamp or with an approved cable connector in one of the three

knock-out points at the sides of the PI backcan.

4. Cut hole in the proper location in the ceiling using a pad saw. Place the pre-install backcan over the

hole. (Fig.7)

Conduit

Squeeze

Connector

Fig.5

Fig.6

Fig.7

5. Go to the ‘Wiring and Setting Up’ chapter, then return to point 6 below.

6. Slide the speaker assembly through the hole. Turn the screws (denoted “Screw Fix”) clockwise on the front of

the speaker to extend the mounting wings. Tighten the screws until a  rm grip is achieved. (NOTE: Screws have

a PoziDriv head; use of a PoziDriv driver is recommended). If using a power driver,

TANNOY

recommends a torque

setting of 1.5 Nm. (Fig.8)

DO NOT OVERTIGHTEN!

7. Attach the nylon safety to the hooks on the front ba e before attaching the grille by presenting it to the speakers

and allowing the magnets to pull it into position. (Fig.9)

Fig.8

Fig.9

16 CMS 3.0 Series Quick Start Guide 17

Wiring and Setting Up

1. Open the wiring cover (if applicable) and locate the Euro-type connector plug and socket at the back

of the speaker. (Fig.1)

2. For connection to an ampli er, use Pins 1 and 2 (Fig.2):

• Pin 1 is positive

• Pin 2 is negative

For connection to additional speakers in a distributed line, Pins 3 and 4 are in parallel where:

• Pin 3 is negative

• Pin 4 is positive

3. Close the wiring cover and tighten both screws on the cable clamp (if applicable).

4. Use the rotary switch on the front of the unit to select low impedance (LoZ) mode or high impedance

(70 V or 100 V) for distributed applications.

THE SPEAKER IS SUPPLIED IN LOW IMPEDANCE MODE. NEVER CONNECT THE SPEAKER TO

A 70/100 VOLT AMPLIFIER WHILE IT IS SET FOR LOW IMPEDANCE.

CMS 403DCe/ICTe and CMS 503DC/ICT models (all variants) use a 30 W transformer. In distributed line

applications, the transformer can be tapped at 30 W, 15 W and 7.5 W, with an additional 3.75 W tap

for 70 V line systems. (Fig.3)

CMS 603DC/ICT and CMS 803DC models (all variants) use a 60 W transformer. In distributed line

applications, the transformer can be tapped at 60 W, 30 W and 15 W, with an additional 7.5 W tap for

70 V line systems. (Fig.4)

Fig.1

Fig.2

Fig.3

Fig.4

CMS Series Model Dimensions

CMS 803DC BM

Hole Cut-out Size: 295 mm

CMS 803DC PI

Hole Cut-out Size: 295 mm

319.0

[12.56"]

327.7

[12.90"]

5.2

[0.20"]

310.5

[12.22"]

286.4

[11.27"]

319.0

[12.56"]

286.4

[11.27"]

125.6

[4.94"]

5.2

[0.20"]

18 CMS 3.0 Series Quick Start Guide 19

CMS Series Model Dimensions

CMS 803DC PI BACKCAN

Hole Cut-out Size: 295 mm

CMS 803DCQ

Hole Cut-out Size: 295 mm

Ø397.0

[15.63"]

Ø291.4

[11.47"]

Ø365.0

[14.37"]

8.8

[0.35"]

151.2

[5.95"]

168.5

[6.63"]

319.0

[12.56"]

327.7

[12.90"]

5.2

[0.20"]

310.5

[12.22"]

286.4

[11.27"]

CMS Series Model Dimensions

CMS 603DC BM

Hole Cut-out Size: 253 mm

CMS 603ICT BM

Hole Cut-out Size: 253 mm

273.3

[10.76"]

4.2

[0.17"]

255.8

[10.07"]

244.3

[9.62"]

274.0

[10.79"]

273.8

[10.78"]

4.1

[0.16"]

256.5

[10.10"]

244.3

[9.62"]

274.0

[10.79"]

20 CMS 3.0 Series Quick Start Guide 21

CMS Series Model Dimensions

CMS 603DC PI

Hole Cut-out Size: 253 mm

CMS 603ICT PI

Hole Cut-out Size: 253 mm

274.0

[10.79"]

4.1

[0.16"]

244.3

[9.62"]

100.0

[3.94"]

100.0

[3.94"]

4.1

[0.16"]

244.3

[9.62"]

273.5

[10.77"]

CMS Series Model Dimensions

CMS 603DC PI BACKCAN

Hole Cut-out Size: 253 mm

CMS 603ICT PI BACKCAN

Hole Cut-out Size: 253 mm

Ø351.0

[13.82"]

Ø249.4

[9.82"]

168.5

[6.63"]

8.8

[0.35"]

151.2

[5.95"]

Ø319.0

[12.56"]

Ø351.0

[13.82"]

Ø249.4

[9.82"]

168.5

[6.63"]

8.8

[0.35"]

151.2

[5.95"]

Ø319.0

[12.56"]

22 CMS 3.0 Series Quick Start Guide 23

CMS Series Model Dimensions

CMS 603ICT LS

Hole Cut-out Size: 253 mm

273.8

[10.78"]

4.1

[0.16"]

256.5

[10.10"]

244.3

[9.62"]

274.0

[10.79"]

CMS Series Model Dimensions

CMS 503DC BM

Hole Cut-out Size: 190 mm

CMS 503ICT BM

Hole Cut-out Size: 190 mm

205.9

[8.11"]

181.3

[7.14"]

205.3

[8.08"]

188.0

[7.40"]

4.5

[0.18"]

205.9

[8.11"]

181.3

[7.14"]

205.8

[8.10"]

188.5

[7.42"]

4.2

[0.17"]

24 CMS 3.0 Series Quick Start Guide 25

CMS Series Model Dimensions

CMS 503DC LP

Hole Cut-out Size: 253 mm

CMS 503ICT LP

Hole Cut-out Size: 253 mm

274.0

[10.79"]

98.6

[3.88"]

4.2

[0.17"]

244.3

[9.62"]

274.0

[10.79"]

98.6

[3.88"]

4.2

[0.17"]

244.3

[9.62"]

CMS Series Model Dimensions

CMS 503DC PI

Hole Cut-out Size: 190 mm

CMS 503ICT PI

Hole Cut-out Size: 190 mm

205.9

[8.11"]

133.3

[5.25"]

4.2

[0.17"]

205.9

[8.11"]

131.7

[5.19"]

4.2

[0.17"]

181.3

[7.14"]

26 CMS 3.0 Series Quick Start Guide 27

CMS Series Model Dimensions

CMS 503DC PI BACKCAN

Hole Cut-out Size: 190 mm

CMS 503ICT PI BACKCAN

Hole Cut-out Size: 190 mm

Ø288.0

[11.34"]

Ø256.0

[10.08"]

8.8

[0.35"]

136.2

[5.36"]

153.5

[6.04"]

Ø186.4

[7.34"]

Ø288.0

[11.34"]

Ø256.0

[10.08"]

8.8

[0.35"]

136.2

[5.36"]

153.5

[6.04"]

Ø186.4

[7.34"]

CMS Series Model Dimensions

CMS 403DCe

Hole Cut-out Size: 187 mm

CMS 403ICTe

Hole Cut-out Size: 187 mm

Painting

If desired, the grille and baffle panel may be painted to match the surrounding décor.

Painting the baffle:

• Carefully mask o the driver assembly using the paint mask provided to ensure that the paint does not come into contact with the cone and roll surround.

• Apply several thin coats of paint – this will provide a better  nish than one overly thick coat.

Painting the grille:

• Carefully remove the acoustically transparent grille cloth from the reverse side of the grille.

• Paint the grille and then replace the grille cloth - several thin coats of paint will provide a better  nish than one overly thick coat.

• Re-bond the grille cloth to the grille over the entire area using a light spray-adhesive to avoid audible resonances.

Ø205.0

[8.07"]

34.2

[1.35"]

147.6

[5.81"]

Ø181.1

[7.13"]

Ø205.0

34.2

[1.35"]

147.6

[5.81"]

Ø181.1

[7.13"]

28 CMS 3.0 Series Quick Start Guide 29

Technical Speci cations

CMS 803DC Models CMS 803DCQ Model

Performance

Frequency response (-3 dB)

(1)

47 Hz - 30 kHz BM Backcan 47 Hz - 30 kHz

Frequency range (-10 dB)

(1)

40 Hz - 35 kHz BM Backcan

Frequency range (-10 dB)

(1)

41 Hz - 35 kHz PI Backcan

System sensitivity (1 W @ 1 m)

(2)

92 dB (1 W = 4 V for 16 Ohms) 93 dB (1 W = 4 V for 16 Ohms)

Nominal Coverage Angle 90 degrees conical 60 degrees conical

Power Handling

(3)

Average 90 W

Programme 180 W

Peak 360 W

Recommended Amplifier Power 180 W @ 16 Ohms

Nominal Impedance (Lo, Z) 16 Ohms

Rated maximum SPL

Average 112 dB 113 dB

Peak 118 dB 119 dB

With THP60 - Average 110 dB 111 dB

Transformer Taps (via front rotary switch)

70 V 60 W (83 Ω) / 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / OFF & low impedance operation

100 V 60 W (165 Ω) / 30 W (330 Ω) / 15 W (660 Ω) / OFF & low impedance operation

Transducers

Dual Concentric point source driver 1 x 200 mm (8.0") Dual Concentric driver, using Omnimagnet technology

Low Frequency 44 mm (1.75") voice coil, treated multi  ber paper pulp cone

High Frequency 25 mm (1.00") PEI dome

Physical

Enclosure

Backcan Zinc plated steel

Ba e Re ex loaded UL 94V-0 rated ABS

Grille Steel, with weather resistant coating

Safety Features Safety ring located at rear of enclosure for load bearing safety bond

Clamping Design Security toggle clamp Min / Max clamping range 9.5 mm (0.37") / 60 mm (2.36") Recommended clamp torque: 1.5 Nm

Backcan Options

Blind Mount (BM) Complete with  xed backcan —

Pre Install (PI) Separate backcan for pre-installation —

Cable Entry Options Cable clamp & squeeze connector for conduit up to 22 mm

Conduit Knockouts on PI Backcan 3 Sets of horizontal positions 19 / 22 / 28 mm (0.75" / 0.87" / 1.10")

Connectors Removable locking connector with screw terminals with “loop through” facility

Compliance UL-1480, UL-2043, CE

Notes:

1. Average over stated bandwidth. Measured in an IEC ba e in an Anechoic Chamber

2. Unweighted pink noise input, measured at 1 metre on axis

3. Long term power handling capacity as de ned in EIA - 426B test

A full range of measurements, performance data, CLF and Ease Data for CMS 803DC/CMS 803DCQ can be downloaded from www.tannoypro.com.

TANNOY operates a policy of continuous research and development. The introduction of new materials or manufacturing methods may introduce variations in actual performance; however, actual performance always will equal or exceed the published speci cations, which

TANNOY reserves the right to alter without prior notice. Please verify the latest speci cations when dealing with critical applications.

CMS 803DC Models CMS 803DCQ Model

Physical

Dimensions

Bezel diameter 319.0 mm (12.56")

Front of ceiling to rear of backcan — 310.5 mm (12.22")

Front of ceiling to top of safety loop — 327.7 mm (12.90")

BM Model: Front of ceiling to rear of backcan 310.5 mm (12.22") —

BM Model: Front of ceiling to top of safety loop 327.7 mm (12.90") —

PI Model: Front of ceiling surface to rear of speaker unit 125.6 mm (4.94") —

PI Model: Front of accessory backcan bezel to top of

safety loop

168.5 mm (6.63") —

Hole cutout diameter (all models) 295 mm (11.61")

Net Weight (ea) — 8.5 kg (18.74 lbs)

CMS 803DC BM 8.5 kg (18.74 lbs) —

CMS 803DC PI 5.0 kg (11.02 lbs) —

PI Backcan 4.2 kg (9.25 lbs) —

Included Accessories C-Ring, tile-bridge kit, paint mask, cut-out template, grille

Optional Accessories Plaster (mud) ring, Arco grille

Packed Quantity 2

30 CMS 3.0 Series Quick Start Guide 31

CMS 603DC Models CMS 603ICT Models

Performance

Frequency response (-3 dB)

(1)

BM Backcan 75 Hz - 30 kHz 78 Hz - 22 kHz

Frequency range (-10 dB)

(1)

BM Backcan 50 Hz - 30 kHz 51 Hz - 24 kHz

Frequency range (-10 dB)

(1)

PI Backcan 46 Hz - 30 kHz 46 Hz - 24 kHz

System sensitivity (1 W @ 1 m)

(2)

91 dB (1 W = 4 V for 16 Ohms)

Nominal Coverage Angle 90 degrees conical 90 degrees conical

Coverage Angle (1 kHz to 6 kHz) 92 degrees

Directivity Factor (Q) 7.1 averaged 1 kHz to 6 kHz

Directivity Index (DI) 7.9 averaged 1 kHz to 6 kHz

Power Handling

(3)

Average 80 W 60 W

Programme 160 W 120 W

Peak 320 W 240 W

Recommended Amplifier Power 160 W @ 16 Ohms 120 W @ 16 Ohms

Nominal Impedance (Lo, Z) 16 Ohms

Rated maximum SPL

Average 110 dB 109 dB

Peak 116 dB 115 dB

Transformer Taps (via front rotary switch)

70 V 60 W (83 Ω) / 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / OFF & low impedance operation

100 V 60 W (165 Ω) / 30 W (330 Ω) / 15 W (660 Ω) / OFF & low impedance operation

Crossover — 7 kHz inductively coupled

Transducers

Dual Concentric point source driver

1 x 165 mm (6.5") Dual Concentric driver,

using Omnimagnet technology

—

Low Frequency 44 mm (1.75") voice coil, treated multi  ber paper pulp cone 165 mm (6.50") mineral loaded polypropylene

High Frequency 25 mm (1.00") PEI dome ICT aluminium dome

Physical

Enclosure

Backcan Zinc plated steel

Ba e Re ex loaded UL 94V-0 rated ABS

Grille Steel, with weather resistant coating

Safety Features Safety ring located at rear of enclosure for load bearing safety bond

CMS 603ICT LS UL 1480 UUMW certi cation for Life Safety applications

Clamping Design Security toggle clamp Min / Max clamping range 9.5 mm (0.37") / 60 mm (2.36") Recommended clamp torque: 1.5 Nm

Backcan Options

Blind Mount (BM) Complete with  xed backcan

Pre Install (PI) Separate backcan for pre-installation

Cable Entry Options Cable clamp & squeeze connector for conduit up to 22 mm

Conduit Knockouts on PI Backcan 3 Sets of horizontal positions 19 / 22 / 28 mm (0.75" / 0.87" / 1.10")

Connectors Removable locking connector with screw terminals with “loop through” facility

Compliance UL-1480, UL-2043, CE

Notes:

1. Average over stated bandwidth. Measured in an IEC ba e in an Anechoic Chamber

2. Unweighted pink noise input, measured at 1 metre on axis

3. Long term power handling capacity as de ned in EIA - 426B test

A full range of measurements, performance data, CLF and Ease Data for CMS 603DC/CMS 603ICT can be downloaded from www.tannoypro.com.

TANNOY reserves the right to alter without prior notice. Please verify the latest speci cations when dealing with critical applications.

CMS 603DC Models CMS 603ICT Models

Physical

Dimensions

Bezel diameter 274.0 mm (10.79")

BM Model: Front of ceiling to rear of backcan 255.8 mm (10.07") 256.5 mm (10.10")

BM Model: Front of ceiling to top of safety loop 273.3 mm (10.76") 273.8 mm (10.78")

PI Model: Front of ceiling surface to rear of speaker unit 100.7 mm (3.96") 100.0 mm (3.94")

PI Model: Front of accessory backcan bezel to top of

safety loop

168.5 mm (6.60")

Hole cutout diameter (all models) 253 mm (9.96")

Net Weight (ea)

CMS 603DC BM 6.6 kg (14.6 lbs) —

CMS 603DC PI 3.8 kg (8.37 lbs) —

CMS 603ICT BM — 5.4 kg (11.9 lbs)

CMS 603ICT PI — 2.7 kg (5.95 lbs)

PI Backcan 3.7 kg (8.1 lbs)

Included Accessories C-Ring, tile-bridge kit, paint mask, cut-out template, grille

Optional Accessories Plaster (mud) ring, Arco grille

Packed Quantity 2

32 CMS 3.0 Series Quick Start Guide 33

CMS 503DC Models CMS 503DC LP Model

Performance

Frequency response (-3 dB)

(1)

85 Hz - 50 kHz BM Backcan 88 Hz - 22 kHz

Frequency range (-10 dB)

(1)

74 Hz - 54 kHz BM Backcan 77 Hz - 24 kHz

Frequency range (-10 dB)

(1)

70 Hz - 54 kHz PI Backcan —

System sensitivity (1 W @ 1 m)

(2)

89 dB (1 W = 4 V for 16 Ohms)

Nominal Coverage Angle 90 degrees conical

Power Handling

(3)

Average 60 W

Programme 120 W

Peak 240 W

Recommended Amplifier Power 120 W @ 16 Ohms

Nominal Impedance (Lo, Z) 16 Ohms

Rated maximum SPL

Average 107 dB

Peak 113 dB

Transformer Taps (via front rotary switch)

70 V 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / 3.75 W (1320 Ω) / OFF & low impedance operation

100 V 30 W (330 Ω) / 15 W (660 Ω) / 7.5 W (1320 Ω) / OFF & low impedance operation

Transducers

Dual Concentric point source driver 1 x 130 mm (5.0") Dual Concentric driver, using Omnimagnet technology

Low Frequency 35 mm (1.38") voice coil, treated multi  ber paper pulp cone

High Frequency 20 mm (0.79") PEI dome

Physical

Enclosure

Backcan Zinc plated steel

Ba e Re ex loaded UL 94V-0 rated ABS

Grille Steel, with weather resistant coating

Safety Features Safety ring located at rear of enclosure for load bearing safety bond

Clamping Design Security toggle clamp Min / Max clamping range 9.5 mm (0.37") / 60 mm (2.36") Recommended clamp torque: 1.5 Nm

Backcan Options

Blind Mount (BM) Complete with  xed backcan —

Pre Install (PI) Separate backcan for pre-installation —

Cable Entry Options Cable clamp & squeeze connector for conduit up to 22 mm

Conduit Knockouts on PI Backcan

3 Sets of horizontal positions 19 / 22 / 28 mm

(0.75" / 0.87" / 1.10")

—

Connectors Removable locking connector with screw terminals with “loop through” facility

Compliance UL-1480, UL-2043, CE

Dimensions

Bezel diameter 205.9 mm (8.11") 274.0 mm (10.79")

Front of ceiling to rear of backcan — 98.6 mm (3.88")

BM Model: Front of ceiling to rear of backcan 188.0 mm (7.40") —

BM Model: Front of ceiling to top of safety loop 205.3 mm (8.08") —

PI Model: Front of ceiling surface to rear of speaker unit 133.3 mm (5.25") —

PI Model: Front of accessory backcan bezel to top of

safety loop

153.5 mm (6.04") —

Hole cutout diameter (all models) 190 mm (7.48") 253.0 mm (9.96")

Net Weight (ea) — 4.7 kg (10.36 lbs)

CMS 503DC BM 4.3 kg (9.47 lbs) —

CMS 503DC PI 3.2 kg (7.05 lbs) —

PI Backcan 1.9 kg (4.18 lbs) —

Included Accessories C-Ring, tile-bridge kit, paint mask, cut-out template, grille

Optional Accessories Plaster (mud) ring, Arco grille

Packed Quantity 2

Notes:

1. Average over stated bandwidth. Measured in an IEC ba e in an Anechoic Chamber

2. Unweighted pink noise input, measured at 1 metre on axis

3. Long term power handling capacity as de ned in EIA - 426B test

A full range of measurements, performance data, CLF and Ease Data for CMS 503DC/CMS 503DC LP can be downloaded from www.tannoypro.com.

TANNOY reserves the right to alter without prior notice. Please verify the latest speci cations when dealing with critical applications.

CMS 503ICT Models CMS 503ICT LP Model

Performance

Frequency response (-3 dB)

(1)

85 Hz - 22 kHz BM Backcan 88 Hz - 50 kHz

Frequency range (-10 dB)

(1)

74 Hz - 24 kHz BM Backcan 77 Hz - 54 kHz

Frequency range (-10 dB)

(1)

71 Hz - 24 kHz PI Backcan —

System sensitivity (1 W @ 1 m)

(2)

89 dB (1 W = 4 V for 16 Ohms)

Nominal Coverage Angle 90 degrees conical

Coverage Angle (1 kHz to 6 kHz) 105 degrees —

Directivity Factor (Q) 5.6 averaged 1 kHz to 6 kHz —

Directivity Index (DI) 7.0 averaged 1 kHz to 6 kHz —

Power Handling

(3)

Average 50 W

Programme 100 W

Peak 200 W

Recommended Amplifier Power 100 W @ 16 Ohms

Nominal Impedance (Lo, Z) 16 Ohms

Rated maximum SPL

Average 106 dB

Peak 112 dB

Transformer Taps (via front rotary switch)

70 V 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / 3.75 W (1320 Ω) / OFF & low impedance operation

100 V 30 W (330 Ω) / 15 W (660 Ω) / 7.5 W (1320 Ω) / OFF & low impedance operation

Crossover 7 kHz inductively coupled —

Transducers

Low Frequency 130 mm (5.00") mineral loaded polypropylene 1 x 130 mm (5.0") mineral loaded polypropylene

High Frequency ICT aluminium dome ICT

Physical

Enclosure

Backcan Zinc plated steel

Ba e Re ex loaded UL 94V-0 rated ABS

Grille Steel, with weather resistant coating

Safety Features Safety ring located at rear of enclosure for load bearing safety bond

Clamping Design

Security toggle clamp Min / Max clamping range 9.5 mm (0.37") / 60 mm (2.36") Recommended clamp torque: 1.5 Nm

Backcan Options

Blind Mount (BM) Complete with  xed backcan —

Pre Install (PI) Separate backcan for pre-installation —

Cable Entry Options Cable clamp & squeeze connector for conduit up to 22 mm

Conduit Knockouts on PI Backcan

3 Sets of horizontal positions 19 / 22 / 28 mm

(0.75" / 0.87" / 1.10")

—

Connectors Removable locking connector with screw terminals with “loop through” facility

Compliance UL-1480, UL-2043, CE

Dimensions

Bezel diameter 205.9 mm (8.11") 274.0 mm (10.79")

Front of ceiling to rear of backcan 98.6 mm (3.88")

BM Model: Front of ceiling to rear of backcan 188.5 mm (7.42") 98.6 mm (3.88")

BM Model: Front of ceiling to top of safety loop 205.8 mm (8.10") —

PI Model: Front of ceiling surface to rear of speaker unit 131.7 mm (5.19") —

PI Model: Front of accessory backcan bezel to top of

safety loop

153.5 mm (6.04")

Hole cutout diameter (all models) 190 mm (7.48") 253.0 mm (9.96")

Net Weight (ea) — 4.4 kg (9.70 lbs)

CMS 503ICT BM 3.95 kg (8.70 lbs) —

CMS 503ICT PI 2.95 kg (6.50 lbs) —

PI Backcan 1.9 kg (4.18 lbs) —

Included Accessories C-Ring, tile-bridge kit, paint mask, cut-out template, grille

Optional Accessories Plaster (mud) ring, Arco grille

Packed Quantity 2

Notes:

1. Average over stated bandwidth. Measured in an IEC ba e in an Anechoic Chamber

2. Unweighted pink noise input, measured at 1 metre on axis

3. Long term power handling capacity as de ned in EIA - 426B test

A full range of measurements, performance data, CLF and Ease Data for CMS 503ICT/CMS 503ICT LP can be downloaded from www.tannoypro.com.

TANNOY reserves the right to alter without prior notice. Please verify the latest speci cations when dealing with critical applications.

34 CMS 3.0 Series Quick Start Guide 35

Other important information

1. Register online. Please register your new

Music Tribe equipment right after you purchase it by

visiting tannoy.com. Registering your purchase using our

simple online form helps us to process your repair claims

more quickly and e ciently. Also, read the terms and

conditions of our warranty, if applicable.

2. Malfunction. Should your Music Tribe

Authorized Reseller not be located in your vicinity,

you may contact the Music Tribe Authorized Ful ller for

your country listed under “Support” at tannoy.com. Should

your country not be listed, please check if your problem

can be dealt with by our “Online Support” which may also

be found under “Support” at tannoy.com. Alternatively,

please submit an online warranty claim at behringer.com

BEFORE returning the product.

3. Power Connections. Before plugging the

unit into a power socket, please make sure you are using

the correct mains voltage for your particular model.

Faulty fuses must be replaced with fuses of the same type

and rating without exception.

Important information

CMS 403DCe Model CMS 403ICTe Model

Performance

Frequency response (-3 dB)

(1)

110 Hz - 50 kHz BM Backcan 110 Hz - 22 kHz

Frequency range (-10 dB)

(1)

80 Hz - 54 kHz BM Backcan 80 Hz - 24 kHz

System sensitivity (1 W @ 1 m)

(2)

88 dB (1 W = 4 V for 16 Ohms)

Nominal Coverage Angle 90 degrees conical

Coverage Angle (1 kHz to 6 kHz) —120 degrees

Directivity Factor (Q) — 5.26 averaged 1 kHz to 6 kHz

Directivity Index (DI) — 6.30 averaged 1 kHz to 6 kHz

Power Handling

(3)

Average 40 W

Peak 160 W

Recommended Amplifier Power 80 W @ 16 Ohms

Nominal Impedance (Lo, Z) 16 Ohms

Rated maximum SPL

Average 104 dB

Peak 110 dB

Transformer Taps (via front rotary switch)

70 V 30 W (165 Ω) / 15 W (330 Ω) / 7.5 W (660 Ω) / 3.75 W (1320 Ω) / OFF & low impedance operation

100 V 30 W (330 Ω) / 15 W (660 Ω) / 7.5 W (1320 Ω) / OFF & low impedance operation

Crossover — 7 kHz inductively coupled

Transducers

Dual Concentric point source driver

1 x 100 mm (4.0") Dual Concentric driver,

using Omnimagnet technology

100 mm (4.00") mineral loaded polypropylene

Low Frequency 35 mm (1.38") voice coil, treated multi  ber paper pulp cone 19 mm (0.75") ICT aluminium dome

High Frequency 20 mm (0.79") PEI dome —

Physical

Enclosure

Backcan Re ex loaded UL 94V-0 rated ABS

Ba e Re ex loaded UL 94V-0 rated ABS

Grille Steel, with weather resistant coating

Safety Features Safety ring located at rear of enclosure for load bearing safety bond

Clamping Design Min / Max clamping range: 0.0 mm (0.0") / 20.0 mm (0.79")Recommended clamp torque: 1.5 Nm

Backcan

Blind Mount (BM) Complete with  xed backcan —

Connectors Removable locking connector with screw terminals with “loop through” facility

Compliance UL-1480, UL-2043, CE

Dimensions

Bezel diameter 205.0 mm (8.07")

Front of ceiling to rear of pod 147.6 mm (5.81")

Hole cutout diameter 187 mm (7.36")

Net Weight (ea) 3.2 kg (7.05 lbs) 3.0 kg (6.61 lbs)

Included Accessories C-Ring, tile-bridge kit, paint mask, cut-out template, grille

Optional Accessories Plaster (mud) ring

Packed Quantity 2

Notes:

1. Average over stated bandwidth. Measured in an IEC ba e in an Anechoic Chamber

2. Unweighted pink noise input, measured at 1 metre on axis

3. Long term power handling capacity as de ned in EIA - 426B test A full range of measurements, performance data, CLF and Ease Data for CMS 403DCe/CMS 403ICTe can be downloaded from www.tannoypro.com.

TANNOY reserves the right to alter without prior notice. Please verify the latest speci cations when dealing with critical applications.