Shading Systems Gen3 Single Shade Power Supply Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

LOW VOLTAGE ROLLER SHADE
SINGLE SHADE
INSTALLATION INSTRUCTIONS
IMPORTANT
Read and understand all instructions before installing.
This document assumes that you have already installed roller
shade brackets.
We do not recommend installing the shade’s wired end in the
locking bracket. Read and understand all instructions before
installing. Always wear personal protection equipment including
safety glasses and gloves. Use a ladder per its manufacturer’s
instructions. Work safely!
Tools Required
Measuring Tape
Wire Strippers
Ladder
1/8” Flat Head Screwdriver
Recommended Items
Wire Management Clips
PARTS LIST
Part Quantity
Power Supply 1
Power Cord 1 (per shade)
INSTALLATION
1. Lay out the Power Supply, the shade, and the Power
Cord. Ensure that cords and wires are of sufficient
length and that Distribution Panel is located away from
water and flammable materials.
2. Connect the Power Cord to the Power Supply.
IMPORTANT: Do not connect the Power Cord to the
wall outlet at this time!
3. Place the shade in the brackets and route the shade’s
wires in such a way that they are hidden from view, but
still accessible. Use wire clips as needed for routing.
4. Terminate the Power Supply’s Quick Connector to
shade’s connector.
5. Please see Qadvanced Roller Shade Gen. 3
Programming Instructions for pairing the remote and
learning shade limits.
Around Back Through Keyhole
Pub #9000200 Revised: 09/2018
For more information visit us at qmotionshades.com or call 877.849.6070
© 2018 QMotion. QMotion is a trademark. All rights reserved.
Motorized Roller Shades
QLVS-433, QMLV-433FM
LOW VOLTAGE SHADE
CAN RSS-Gen/CNR-Gen.
FCC Regulatory Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this device not expressly approved by QMotion Advanced Shading Systems could void the user’s authority to
operate the equipment.
Industry Canada Regulatory Statements:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
This Class B digital apparatus meets all requirements of the Canadian Intereference Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel bouilleur.
Do not operate at temperatures below 32° F or above 130° F. End user must ensure that shade being used is fire resistant. Keep transmitter away
from children. Periodically examine assembly and brackets for signs of wear and discontinue use if repair is necessary. The controller and transmitter
assemblies contain no serviceable parts.
Ton de Zeeuw
Contact for QMotion
Raritan Europe B.V.
Jan van Galenstraat 59
3115 JG Schiedam
The Netherlands
Tel: +31.(0)10.2844040 • Fax: +31.(0)10.2844049
VAT: NL803738614B01 / KvK-CoC: 24256806 / EORI: NL803738614
  • Page 1 1
  • Page 2 2

Shading Systems Gen3 Single Shade Power Supply Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à