Zanussi ZDF26017WA Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur

Ce manuel convient également à

GETTING
STARTED?
EASY.
User Manual
ZDF26017WA
ZDF26017XA
EN User Manual 2
Dishwasher
FR Notice d'utilisation 18
Lave-vaisselle
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
This appliance is intended to be used in household and similar
applications such as:
farm houses; staff kitchen areas in shops, offices and other
working environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments.
2
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 8 (0.8) bar (MPa)
Follow the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
Put the cutlery in the cutlery basket with the sharp ends
pointing down or put them in the cutlery drawer in a horizontal
position with the sharp edges down.
Do not leave the appliance with the open door unattended to
avoid stepping accidentally onto it.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
If the appliance has ventilation openings in the base, they must
not be covered e.g. by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
SAFETY INSTRUCTIONS
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
Remove all the packaging.
Do not install or use a damaged appliance.
Follow the installation instructions supplied with
the appliance.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not install or use the appliance where the
temperature is less than 0 °C.
Install the appliance in a safe and suitable place
that meets installation requirements.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
The appliance must be earthed.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
3
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains
plug from the mains socket. Contact the
Authorised Service Centre to replace the water
inlet hose.
USE
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Dishwasher detergents are dangerous. Follow
the safety instructions on the detergent
packaging.
Do not drink and play with the water in the
appliance.
Do not remove the dishes from the appliance
until the programme is complete. Some
detergent may remain on the dishes.
Do not store items or apply pressure on the
open door of the appliance.
The appliance can release hot steam if you open
the door while a programme operates.
INTERNAL LIGHTING
WARNING! Risk of injury.
Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
To replace the internal lighting, contact the
Authorised Service Centre.
SERVICE
To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children and
pets to get closed in the appliance.
4
CONTROL PANEL
2
1
3
45
1
On/off button
2
Display
3
Indicators
4
Delay button
5
Programme buttons
INDICATORS
Indicator Description
XtraDry indicator.
Rinse aid indicator. It is always off while the programme operates.
Salt indicator. It is always off while the programme operates.
PROGRAMMES
The order of the programmes in the table may not reflect their sequence on the control panel.
5
Programme
Degree of soil
Type of load
Programme phases
Consumption values
1)2)
Duration
(min)
Energy
(kWh)
Water
(l)
3)
Normal soil
Crockery and
cutlery
Prewash
Wash 50 °C
Rinses
Dry
227 1.039 11
4)
All
Crockery,
cutlery, pots
and pans
Prewash
Wash from
45 °C to
70 °C
Rinses
Dry
45 - 156 0.7 - 1.4 7 - 12
Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Wash 70 °C
Rinses
Dry
155 - 170 1.5 - 1.7 14 - 15
5)
Fresh soil
Crockery and
cutlery
Wash 60 °C
or 65 °C
Rinses
30 0.8 10
6)
All Prewash 14 0.1 5
1) The pressure and the temperature of the water, the variations of the mains supply, the options, the quan-
tity of dishes and the degree of soil can change the values.
2) The values for programmes other than ECO are indicative only.
3) This programme offers the most efficient use of water and energy consumption for crockery and cutlery
with normal soil. This is the standard programme for test institutes.
4) The appliance senses the degree of soil and the quantity of items in the baskets. It automatically adjusts
the temperature and the quantity of water, the energy consumption and the programme duration.
5) This programme is suitable for washing a load or a half load with fresh soil. It gives good washing re-
sults in a short time.
6) With this programme, you can quickly rinse off food remains from dishes and prevent odours forming in
the appliance. Do not use detergent with this programme.
INFORMATION FOR TEST INSTITUTES
To receive the necessary information for conducting performance tests (e.g. according to EN60436), send
an email to:
In your request, include the product number code (PNC) from the rating plate.
For any other questions regarding your dishwasher, refer to the service book provided with your appliance.
6
SETTINGS
PROGRAMME SELECTION MODE
In the programme selection mode it is possible to
set a washing programme and to enter the user
mode to change the appliance settings.
To enter the programme selection mode, press on/
off.
The appliance is in programme selection mode
when
programme indicator is on and the
display shows the programme duration.
If the control panel does not indicate that the
appliance is in programme selection mode,
implement the Reset procedure.
RESET FUNCTION
Use Reset to:
Reset the currently running programme.
Stop the countdown of the Delay option.
Bring the appliance back to the programme
selection mode.
To Reset, press and hold
and until
the appliance is in programme selection mode.
USER MODE
User mode allows to change the following settings:
Adjust the level of the water softener according
to the water hardness.
Activate or deactivate the rinse aid empty
notification.
Activate or deactivate AirDry.
Before entering user mode, make sure the
appliance is in programme selection mode:
1. Press and hold
and .
The indicators , and
flash.
As the appliance stores the saved settings, there is
no need to configure it before every cycle.
ADJUSTING THE WATER SOFTENER
Make sure that the appliance is in user mode:
1. Press
.
The indicators and are off.
The indicator still flashes.
The display shows the current setting: e.g.
= level 5.
2. Press to change the setting. Each
pressing increases the level number by one.
After reaching level 10, the countdown starts
again from level 1.
3. Press on/off to confirm the setting.
If you use multi-tabs containing salt
and the hardness of your water is
lower than 21°dH, you can set the
lowest water softener level. It
deactivates the salt refill indicator.
If you use standard detergent or multi-
tabs without salt, set the proper water
hardness level to keep the salt refill
indicator active.
THE WATER HARDNESS TABLE
The water softener removes minerals from the water
supply, which would have a negative effect on the
washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. It is important to set the right
level of the water softener to assure good washing
results.
Softening hard water increases the
consumption of water and energy as
well as the programme duration. The
higher the level of water softener, the
higher the consumption and the longer
the duration.
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
7
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
Water softener level
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
5
1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1
2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used, set
the proper water hardness level to keep the
salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
DEACTIVATING THE RINSE AID EMPTY
NOTIFICATION
Make sure that the appliance is in user mode:
1. Press .
The indicators and are off.
The indicator flashes.
The display shows the current setting:
= rinse aid empty notification
activated.
= rinse aid empty notification
deactivated.
2. Press to change the setting.
3. Press on/off to confirm the setting.
When rinse aid chamber is empty, the
rinse aid indicator is on prompting to
refill the rinse aid. If you are using
multi-tabs containing rinse aid and you
are satisfied with the drying result, you
can deactivate the notification.
However, we recommend that you
always use rinse aid for best drying
performance.
If you use standard detergent or multi-
tabs without rinse aid, activate the
notification to keep the rinse aid refill
indicator active.
DEACTIVATING AIRDRY
AirDry improves the drying results with less energy
consumption.
While the drying phase operates, the
device opens the appliance door. The
door is then kept ajar.
8
The duration of the drying phase and the door
opening time vary depending on the selected
programme and options.
When AirDry opens the door, the display shows the
remaining time of the running programme.
By default, AirDry is activated with all programmes
excluding
(if applicable), but it is possible to
deactivate it.
Make sure the appliance is in user mode.
1. Press .
The indicators and
are off.
The indicator flashes.
The display shows the current setting:
= AirDry activated.
=AirDry deactivated.
2. Press to change the setting.
3. Press on/off to confirm the setting.
CAUTION! If children have access to
the appliance, it is advised to
deactivate AirDry as opening the door
may pose a danger.
BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the hardness
of the water supply. If not, adjust the level
of the water softener. Contact your local
water authority to know the water
hardness in your area.
2. Fill the salt container with special salt for
dishwasher.
3. Fill the rinse aid dispenser with special rinse
aid for dishwasher.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance.
Do not use detergent and do not load the
baskets.
ADDING SALT
Before the first use, put one litre of water in the salt container.
CAUTION! Water and salt can come out of the salt container during filling. To prevent
corrosion, start a programme immediately after filling the salt container.
ADDING RINSE AID
2
1
4
3
2
1
The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot
rinse phase.
9
DAILY USE
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in programme
selection mode.
If the salt indicator is on, fill the salt
container.
If the rinse aid indicator is on, fill the rinse
aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the
type of load and the degree of soil.
ADDING DETERGENT
2
1
If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance
door.
ADDING MULTI-TABLETS
2
1
Adjust the water softener to the lowest level.
THE AUTO OFF FUNCTION
This function decreases energy consumption by
deactivating automatically the appliance when it is
not operating.
The function comes into operation:
5 minutes after the completion of the
programme.
After 5 minutes if the programme has not
started.
STARTING A PROGRAMME
1. Keep the appliance door ajar.
2. Press on/off to activate the appliance. Make
sure that the appliance is in programme
selection mode.
10
3. Press the button related to the programme you
want to start. The related programme indicator
flashes and the display shows the programme
duration.
4. Set the applicable options.
5. Close the appliance door to start the
programme.
XTRADRY OPTION
Activate this option when you want to boost the
drying performance. With the use of this option, the
duration of some programmes, water consumption
and the last rinse temperature can be affected.
The XtraDry option is a permanent option for all
programmes other than
and need not to
be selected at every cycle.
ACTIVATING XTRADRY
Make sure the appliance is in programme selection
mode.
To activate XtraDry:
1. Press simultaneously and and hold until
the indicator is on.
2. Select a programme.
3. Set Delay option.
4. Close the appliance door to start the
programme.
Once the programme starts running,
XtraDry cannot be activated.
DELAY OPTION
1. Set a programme.
2. Press Delay until the display shows the delay
time you want to set (1-24h).
The delay time flashes in the display.
3. Close the appliance door. The countdown
starts to decrease by 1 hour.
When the countdown is complete the programme
starts.
OPENING THE DOOR WHILE THE
APPLIANCE OPERATES
Opening the door while a programme is running
stops the appliance. It may affect the energy
consumption and the programme duration. After
closing the door, the appliance continues from the
point of interruption.
If the door is opened during the drying
phase, before AirDry automatically
opens it, the programme ends after 30
seconds.
If the door is closed after it is opened
automatically by AirDry in the drying
phase, the programme ends after 3
minutes.
Do not try to close the appliance door
within 2 minutes after AirDry
automatically opens it, as this may
cause damage to the appliance.
END OF THE PROGRAMME
When the programme is complete, the display
shows: 0:00.
Press on/off or wait 5 minutes for the Auto OFF
function to automatically deactivate the
appliance.
Close the water tap.
If you open the door before the
activation of Auto OFF, the appliance
is automatically deactivated.
HINTS AND TIPS
GENERAL
Follow the hints below to ensure optimal cleaning
and drying results in daily use and to protect the
environment.
Washing dishes in the dishwasher as instructed
in the user manual usually consumes less water
and energy than washing dishes by hand.
Load the dishwasher to its full capacity to save
water and energy. For best cleaning results,
arrange items in the baskets as instructed in the
user manual and do not overload the baskets.
Do not pre-rinse dishes by hand. It increases
the water and energy consumption. When
needed, select a programme with a prewash
phase.
Remove larger residues of food from the dishes
and empty cups and glasses before putting
them inside the appliance.
Soak or slightly scour cookware with firmly
cooked-on or baked-on food before washing it
in the appliance.
Make sure that items in the baskets do not
touch or cover each other. Only then can the
water completely reach and wash the dishes.
11
You can use dishwasher detergent, rinse aid
and salt separately or you can use the multi-
tablets (e.g. ''All in 1''). Follow the instructions
on the packaging.
Select a programme according to the type of
load and the degree of soil. offers the
most efficient use of water and energy
consumption.
To prevent limescale buildup inside the
appliance:
Refill the salt container whenever
necessary.
Use the recommended dosage of the
detergent and rinse aid.
Make sure that the current level of the water
softener agrees with the hardness of the
water supply.
Follow the instructions in the chapter "Care
and cleaning".
THE WATER SOFTENER
The water softener removes minerals from the water
supply, which would have a detrimental effect on
the washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. It is important to set the right
level of the water softener to assure good washing
results.
USING SALT, RINSE AID AND DETERGENT
Only use salt, rinse aid and detergent for
dishwasher. Other products can cause damage
to the appliance.
In areas with hard and very hard water we
recommend to use plain dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
At least once a month run the appliance with the
use of appliance cleaner which is particularly
suitable for this purpose.
Detergent tablets do not fully dissolve with short
programmes. To prevent detergent residues on
the tableware, we recommend that you use the
tablets with long programmes.
Always use the correct quantity of detergent.
Insufficient dosage of detergent can result in
poor cleaning results and hard-water filming or
spotting on the items. Using too much detergent
with soft or softened water results in detergent
residues on the dishes. Adjust the amount of
detergent based on the water hardness. Refer
to the instructions on the detergent packaging.
Always use the correct quantity of rinse aid.
Insufficient dosage of rinse aid decreases the
drying results. Using too much rinse aid results
in bluish layers on the items.
Make sure that the water softener level is
correct. If the level is too high, the increased
quantity of salt in the water might result in rust
on cutlery.
WHAT TO DO IF YOU WANT TO STOP USING
MULTI-TABLETS
Before you start to use separately detergent, salt
and rinse aid do the following procedure.
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the shortest programme with a rinsing
phase. Do not add detergent and do not put
dishes in the baskets.
4. When the programme is completed, adjust the
water softener according to the water hardness
in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.
LOADING THE BASKETS
Always use the whole space of the baskets.
Only use the appliance to wash items that are
dishwasher-safe.
Do not wash in the appliance items made of
wood, horn, aluminium, pewter and copper as
they could crack, warp, get discoloured or
pitted.
Do not wash in the appliance items that can
absorb water (sponges, household cloths).
Remove remaining food from the items.
Make soft the remaining burned food on the
items.
Put hollow items (cups, glasses and pans) with
the opening down.
Make sure that cutlery and dishes do not bond
together. Mix spoons with other cutlery.
Make sure that glasses do not touch other
glasses.
Put light items in the upper basket. Make sure
that the items do not move.
Make sure that the spray arm can move freely
before you start a programme.
BEFORE STARTING A PROGRAMME
Before you start the selected programme, make
sure that:
The filters are clean and correctly installed.
The cap of the salt container is tight.
12
The spray arms are not clogged.
There is enough salt and rinse aid (unless you
use multi-tablets).
The arrangement of the items in the baskets is
correct.
The programme is suitable to the type of load
and the degree of soil.
The correct quantity of detergent is used.
UNLOADING THE BASKETS
1. Let the tableware cool down before you
remove it from the appliance. Hot items can be
easily damaged.
2. First remove items from the lower basket, then
from the upper basket.
After the programme is completed,
water can still remain on the inside
surfaces of the appliance.
CARE AND CLEANING
WARNING! Before maintenance,
deactivate the appliance and
disconnect the mains plug from the
main socket.
Dirty filters and clogged spray arms
decrease the washing results. Make a
check regularly and, if necessary, clean
them.
CLEANING THE FILTERS
B
A
C
Make sure that there are no residues of food or soil in or around the edge of the sump.
Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides.
Reassemble the filters (A) and (B).
Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks.
An incorrect position of the filters can cause bad washing results and damage to the
appliance
CLEANING THE SPRAY ARMS
Do not remove the spray arms. If the holes in the
spray arms are clogged, remove remaining parts of
soil with a thin pointed object.
EXTERNAL CLEANING
Clean the appliance with a moist soft cloth.
Only use neutral detergents.
Do not use abrasive products, abrasive cleaning
pads or solvents.
13
INTERNAL CLEANING
Carefully clean the appliance, including the
rubber gasket of the door, with a soft damp
cloth.
If you regularly use short duration programmes,
these can leave deposits of grease and
limescale inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per month.
To maintain the performance of your appliance
at its best, we recommend to use monthly a
specific cleaning product for dishwashers.
Follow carefully the instructions on the
packaging of the product.
TROUBLESHOOTING
WARNING! Improper repair of the
appliance may pose a danger to the
safety of the user. Any repairs must be
performed by qualified personnel.
The majority of problems that may occur can
be solved without the need to contact an
Authorised Service Centre.
Refer to the below table for information on possible
problems.
With some problems, the display shows an alarm
code.
Problem and alarm code Possible cause and solution
You cannot activate the appli-
ance.
Make sure that the mains plug is connected to the mains sock-
et.
Make sure that there is no damaged fuse in the fuse box.
The programme does not start. Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or wait for the end of
the countdown.
The appliance recharges the resin inside the water softener.
The duration of the procedure is approximately 5 minutes.
The appliance does not fill with
water.
The display shows i10 or i11.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
The appliance does not drain
the water.
The display shows i20.
Make sure that the sink spigot is not clogged.
Make sure that the interior filter system is not clogged.
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on.
The display shows i30.
Close the water tap.
Make sure that the appliance is correctly installed.
Make sure the baskets are loaded as instructed in the user
manual.
The appliance stops and starts
more times during operation.
It is normal. It provides optimal cleaning results and energy sav-
ings.
The programme lasts too long. If the delayed start option is set, cancel the delay setting or wait
for the end of the countdown.
14
Problem and alarm code Possible cause and solution
The displayed programme du-
ration is different than the du-
ration in the consumption val-
ues table.
Refer to the consumption values table in the chapter "Pro-
grammes".
The remaining time in the dis-
play increases and skips nearly
to the end of programme time.
This is not a defect. The appliance is working correctly.
Small leak from the appliance
door.
The appliance is not levelled. Loosen or tighten the adjustable
feet (if applicable).
The appliance door is not centred on the tub. Adjust the rear
foot (if applicable).
The appliance door is difficult
to close.
The appliance is not levelled. Loosen or tighten the adjustable
feet (if applicable).
Parts of the tableware are protruding from the baskets.
The appliance door opens dur-
ing the wash cycle.
The AirDry function is activated. You can deactivate the func-
tion. Refer to "Settings".
Rattling/knocking sounds from
inside the appliance.
The tableware is not properly arranged in the baskets. Refer to
basket loading leaflet.
Make sure that the spray arms can rotate freely.
The appliance trips the circuit-
beaker.
The amperage is insufficient to supply simultaneously all the ap-
pliances in use. Check the socket amperage and the capacity
of the meter or turn off one of the appliances in use.
Internal electrical fault of the appliance. Contact an Authorised
Service Centre.
Refer to "Before first use", "Daily
use", or "Hints and tips" for other
possible causes.
Once you have checked the appliance, deactivate
and activate the appliance. If the problem occurs
again, contact an Authorised Service Centre.
For alarm codes not described in the table, contact
an Authorised Service Centre.
WARNING! We do not recommend
using the appliance until the problem
has been completely fixed. Unplug the
appliance and do not plug it in again
until you are certain that it operates
correctly.
THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY
Problem Possible cause and solution
Poor washing results. Refer to "Daily use", "Hints and tips" and basket loading
leaflet.
Use more intensive washing programmes.
Clean spray arm jets and filter. Refer to "Care and Clean-
ing".
15
Problem Possible cause and solution
Poor drying results. Tableware has been left for too long inside a closed appli-
ance.
There is no rinse aid or the dosage of rinse aid is not enough.
Set the rinse aid dispenser to a higher level.
Plastic items may need to be towel dried.
For the best drying performance activate the option XtraDry
and set AirDry.
We recommend to always use rinse aid, even in combination
with multi-tablets.
There are whitish streaks or blu-
ish layers on glasses and dishes.
The release quantity of rinse aid is too much. Adjust the rinse
aid level to a lower level.
The quantity of detergent is too high.
There are stains and dry water
drops on glasses and dishes.
The released quantity of rinse aid is not sufficient. Adjust the
rinse aid level to a higher level.
The quality of the rinse aid can be the cause.
The dishes are wet. For the best drying performance activate the option XtraDry
and set AirDry .
The programme does not have a drying phase or has a drying
phase with low temperature.
The rinse aid dispenser is empty.
The quality of the rinse aid can be the cause.
The quality of the multi-tablets can be the cause. Try a differ-
ent brand or activate the rinse aid dispenser and use rinse
aid and multi-tablets together.
The interior of the appliance is
wet.
This is not a defect of the appliance. it is caused by the hu-
midity in the air that condenses on the walls.
Unusual foam during washing. Use the detergent designed specifically for dishwashers.
Use a detergent from a different manufacturer.
Do not pre-rinse dishes under running water before putting
them in the appliance.
Traces of rust on cutlery. There is too much salt in the water used for washing. Refer to
"The water softener".
Silver and stainless steel cutlery were placed together. Avoid
to put silver and stainless steel items close together.
There are residues of detergent
in the dispenser at the end of the
programme.
The detergent tablet got stuck in the dispenser and therefore
was not completely washed away by water.
Water cannot wash away the detergent from the dispenser.
Make sure that the spray arm is not blocked or clogged.
Make sure that items in the baskets do not impede the lid of
the detergent dispenser from opening.
Odours inside the appliance. Refer to "Internal cleaning".
16
Problem Possible cause and solution
Limescale deposits on the table-
ware, on the tub and on the in-
side of the door.
The level of salt is low, check the refill indicator.
The cap of the salt container is loose.
Your tap water is hard. Refer to "The water softener".
Even using multi-functional tabs use salt and set regeneration
of the water softener. Refer to "The water softener".
If lime scale deposits still remain, clean the appliance with
appliance cleaners which are particularly suitable for this pur-
pose.
Try different detergent.
Contact the detergent manufacturer.
Dull, discoloured or chipped ta-
bleware.
Make sure that only dishwasher-safe items are washed in the
appliance.
Load and unload the basket carefully. Refer to basket loading
leaflet.
Place delicate items in the upper basket.
Refer to "Before first use", "Daily
use" or "Hints and tips" for other
possible causes.
TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 600 / 850 / 625
Electrical connection
1) Voltage (V) 220 - 240
Frequency (Hz) 50
Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)
Water supply
Cold water or hot water
2) max 60 °C
Capacity Place settings 13
Power consumption Left-on mode (W) 5.0
Off-mode (W) 0.50
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to
decrease energy consumption.
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
17
VISITEZ NOTRE SITE WEB POUR :
Obtenir des conseils d’utilisation, des brochures, un dépanneur, des informations sur le
service et les réparations :
www.zanussi.com/support
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement les
instructions fournies. Le fabricant ne pourra être tenu pour
responsable des blessures et dégâts résultant d'une mauvaise
installation ou utilisation. Conservez toujours les instructions dans
un lieu sûr et accessible pour vous y référer ultérieurement.
SÉCURITÉ DES ENFANTS ET DES PERSONNES
VULNÉRABLES.
Cet appareil peut être utilisé par des enfants âgés d'au moins
8 ans et par des personnes ayant des capacités physiques,
sensorielles ou mentales réduites ou dénuées d’expérience ou
de connaissance, s'ils sont correctement surveillés ou si des
instructions relatives à l'utilisation de l'appareil en toute sécurité
leur ont été données et s’ils comprennent les risques encourus.
Les enfants entre 3 et 8 ans et les personnes ayant un
handicap très important et complexe doivent être tenus à l'écart
de l'appareil, à moins d'être surveillés en permanence.
Les enfants de moins de 3 ans doivent être tenus à l'écart de
l'appareil, à moins d'être surveillés en permanence.
Ne laissez pas les enfants jouer avec l'appareil.
Ne laissez pas les détergents à la portée des enfants.
Tenez les enfants et les animaux éloignés de l'appareil lorsque
la porte est ouverte.
Le nettoyage et l'entretien ne doivent pas être effectués par des
enfants sans surveillance.
SÉCURITÉ GÉNÉRALE
Cet appareil est conçu pour un usage domestique et des
applications équivalentes, comme :
dans des fermes, des coins cuisines réservés au personnel
dans des magasins, bureaux et autres ;
18
pour une utilisation privée, par les clients, dans des hôtels,
motels, chambres d’hôte, et autres types de lieux de séjour ;
Ne modifiez pas les caractéristiques de cet appareil.
La pression de l’eau en fonctionnement (minimale et maximale)
doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa)
Respectez le nombre maximal de 13 couverts.
Si le câble d’alimentation est endommagé, il doit être remplacé
par le fabricant, son service après-vente ou par un
professionnel qualifié afin d’éviter un danger.
Placez les couverts dans le panier à couverts, avec les
extrémités pointues vers le bas, ou placez-les dans le tiroir à
couverts en position horizontale, bords tranchants vers le bas.
Ne laissez pas la porte de l’appareil ouverte sans surveillance
pour éviter de vous prendre accidentellement les pieds dedans.
Avant toute opération d'entretien, éteignez l'appareil et
débranchez la fiche de la prise secteur.
Ne pulvérisez pas d'eau ni de vapeur à haute pression pour
nettoyer l'appareil.
Si l’appareil dispose d’orifices d’aération à la base, veillez à ne
pas les couvrir, p. ex. avec de la moquette.
L’appareil doit être raccordé au réseau d’eau à l’aide des tuyaux
neufs fournis. Les anciens ensembles de tuyaux ne doivent pas
être réutilisés.
CONSIGNES DE SÉCURITÉ
INSTALLATION
AVERTISSEMENT! L'appareil doit
être installé uniquement par un
professionnel qualifié.
Retirez l'intégralité de l'emballage.
N'installez pas et ne branchez pas un appareil
endommagé.
Suivez scrupuleusement les instructions
d'installation fournies avec l'appareil.
Soyez toujours vigilants lorsque vous déplacez
l'appareil car il est lourd. Utilisez toujours des
gants de sécurité et des chaussures fermées.
N'installez pas l'appareil ou ne l'utilisez pas dans
un endroit où la température ambiante est
inférieure à 0 °C.
Installez l'appareil dans un lieu sûr et adapté
répondant aux exigences d'installation.
BRANCHEMENT ÉLECTRIQUE
AVERTISSEMENT! Risque
d'incendie ou d'électrocution.
L’appareil doit être relié à la terre.
Assurez-vous que les paramètres figurant sur la
plaque signalétique correspondent aux données
électriques nominale de l’alimentation secteur.
Utilisez toujours une prise de courant de
sécurité correctement installée.
N'utilisez pas d'adaptateurs multiprise et de
rallonges.
Veillez à ne pas endommager la fiche secteur ni
le câble d'alimentation. Le remplacement du
19
câble d’alimentation de l’appareil doit être
effectué par notre service après-vente agréé.
Ne branchez la fiche secteur dans la prise
secteur qu'à la fin de l'installation. Assurez-vous
que la prise secteur est accessible après
l'installation.
Ne tirez pas sur le câble secteur pour
débrancher l'appareil. Tirez toujours sur la fiche
de la prise secteur.
Cet appareil est fourni avec un câble
d'alimentation de 13 A. Si vous devez changer
le fusible de la fiche secteur, utilisez uniquement
un fusible 13 A approuvé ASTA (BS 1362)
(Royaume-Uni et Irlande uniquement).
RACCORDEMENT À L'ARRIVÉE D'EAU
Veillez à ne pas endommager les tuyaux de
circulation d'eau.
Avant d'installer des tuyaux neufs, des tuyaux
n'ayant pas servi depuis longtemps, lorsqu'une
réparation a été effectuée ou qu'un nouveau
dispositif a été installé (compteurs d'eau, etc.),
laissez l'eau s'écouler jusqu'à ce qu'elle soit
parfaitement propre et claire.
Pendant et après la première utilisation de
l'appareil, vérifiez qu'aucune fuite n'est visible.
Si le tuyau d'arrivée d'eau est endommagé,
fermez immédiatement le robinet d'eau et
débranchez la fiche de la prise secteur.
Contactez le service après-vente pour
remplacer le tuyau d'arrivée d'eau.
UTILISATION
Ne placez pas de produits inflammables ou
d'éléments imbibés de produits inflammables à
l'intérieur ou à proximité de l'appareil, ni sur
celui-ci.
Les produits de lavage pour lave-vaisselle sont
dangereux. Suivez les consignes de sécurité
figurant sur l'emballage du produit de lavage.
Ne buvez pas et ne jouez pas avec l’eau de
l’appareil.
N'enlevez pas la vaisselle de l'appareil avant la
fin du programme. Il se peut que la vaisselle
contienne encore du produit de lavage.
Ne posez pas d’objets et n’appliquez pas de
pression sur la porte ouverte de l'appareil.
L’appareil peut dégager de la vapeur chaude si
vous ouvrez la porte pendant le déroulement
d’un programme.
ÉCLAIRAGE INTÉRIEUR
AVERTISSEMENT! Risque de
blessure.
Concernant la/les lampe(s) à l’intérieur de ce
produit et les lampes de rechange vendues
séparément : Ces lampes sont conçues pour
résister à des conditions physiques extrêmes
dans les appareils électroménagers, telles que
la température, les vibrations, l’humidité, ou sont
conçues pour signaler des informations sur le
statut opérationnel de l’appareil. Elles ne sont
pas destinées à être utilisées dans d'autres
applications et ne conviennent pas à l’éclairage
des pièces d’un logement.
Pour remplacer l'éclairage intérieur, contactez le
service après-vente agréé.
SERVICE
Pour réparer l'appareil, contactez un service
après-vente agréé. Utilisez exclusivement des
pièces d'origine.
Veuillez noter qu’une autoréparation ou une
réparation non professionnelle peuvent avoir
des conséquences sur la sécurité et annuler la
garantie.
MISE AU REBUT
AVERTISSEMENT! Risque de
blessure ou d'asphyxie.
Débranchez l'appareil de l'alimentation
électrique.
Coupez le câble d'alimentation et mettez-le au
rebut.
Retirez le dispositif de verrouillage de la porte
pour empêcher les enfants et les animaux de
s'enfermer dans l'appareil.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Zanussi ZDF26017WA Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues