Hitachi RAC-25CNH2 Manuel utilisateur

SPLIT TYPE

HITACHI

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAS-25CNH2/RAC-25CNH2

OUTDOOR UNIT INDOOR UNIT

RAS-25CNH2

RAC-25CNH2

Instruction manual Page 1~22

To obtain the best performance and ensure years of trouble

free use, please read this instruction manual completely.

Bedlenungsanleitung Suite 23~44

Bitte lesen Sie diese Bedienungsanleitung aufmerksam durch,

um durch richtige Bedienung jahrelangen und störungsfreien

Betrieb zu gewährleisten.

Mode d’emploi Page 45~66

Des performances optimales et un fonctionnement à long

terme seront assurés en appliquant les présentes instructions

après avoir entièrement lu ce mode d’emploi.

Manuale di istruzioni Pag. 67~88

Per garantire la migliore prestazione e la più lunga

durataleggere attentamente e al completo le seguanti

istruzioni.

Manual de instrucciones Página 89~110

Para obtener el mejor funcionamiento y asegurar años de

uso libre de problemas, lea cuidadosamente este manual de

instrucciones.

Manual de instruções Página 111~132

A fim de obter um bom funcionamento e de garantir uma

utilização sem falhas durante muitos anos, é favor ler este

manual de instruções completamente.

O‰ËÁ›Â˜ XÂÈÚÈÛÌÔ‡ ™ÂÏ›‰· 133~154

°È· ÙËÓ Î·Ï‡ÙÂÚË ‰˘Ó·Ù‹ ·ﬁ‰ÔÛË Î·È ÙËÓ Ì·ÎÚÔ¯ÚﬁÓÈ· Î·È

¯ˆÚ›˜ ÚÔ‚Ï‹Ì·Ù· ¯Ú‹ÛË ÙË˜ Û˘ÛÎÂ˘‹˜ ·˘Ù‹˜, ·Ú·Î·ÏÔ‡ÌÂ

‰È·‚¿ÛÙÂ Ï‹Úˆ˜ ÙÈ˜ Ô‰ËÁ›Â˜ ¯ÂÈÚÈÛÌÔ‡ ÙË˜.

Инструкция по эксплуатации

стр. 155~176

Для обеспечения наилууших эксплуатационных

характеристик и многолетней безотказной работы

оборудования необходимо полностыо оэнакомиться с данной

Инструкцией по эксплуатации.

“BESTÄIGUNG” und “Bescheingung des Herstellers/Importeurs” sind am Ende dieser Bedienungsanleitung beschrieben.

– 2 –

!

SAFETY PRECAUTION

●

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

●

Pay special attention to signs of “ Warning” and “ Caution”. The “Warning” section contains matters which,

if not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may

result in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

●

The sign indicate the following meanings.

●

Please keep this manual after reading.

WARNING

PRECAUTIONS DURING INSTALLATION

●

Do not reconstruct the unit.

Water leakage, fault, short circuit or fire may occur if you reconstruct

the unit by yourself.

●

Please ask your sales agent or qualified technician for the installation

of your unit. Water leakage, short circuit or fire may occur if you install

the unit by yourself.

●

Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor,

or the earth line of telephone. Improper installation of earth line may

cause electric shock.

●

A circuit breaker should be installed depending on the mounting site of

the unit. Without a circuit breaker, the danger of electric shock exists.

●

Do not install near location where there is flammable gas. The outdoor

unit may catch fire if flammable gas leaks around it.

●

Please ensure smooth flow of water when installing the drain hose.

CAUTION

!

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

PRECAUTIONS DURING OPERATION

●

Avoid an extended period of direct air flow for your health.

W

A

R

N

I

N

G

!

●

Should abnormal situation arises (like burning smell), please stop operating the unit

and turn off the circuit breaker. Contact your agent. Fault, short circuit or fire may

occur if you continue to operate the unit under abnormal situation.

●

Please contact your agent for maintenance. Improper self maintenance may cause

electric shock and fire.

●

Please contact your agent if you need to remove and reinstall the unit. Electric

shock or fire may occur if you remove and reinstall the unit yourself improperly.

●

Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

●

During thunder storm, disconnect and turn off the circuit breaker.

●

Do not use any conductor as fuse wire, this could cause fatal accident.

!

Make sure to connect earth line.

Indicates the instructions that must be followed.

The sign in the figure indicates prohibition.

W

A

R

N

I

N

G

!

– 3 –

ENGLISH

PRECAUTIONS DURING OPERATION

●

The product shall be operated under the manufacturer specification and

not for any other intended use.

●

Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

●

When operating the unit with burning equipments, regularly ventilate the

room to avoid oxygen insufficiency.

●

Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus

such as the electric kettle, oven etc.

●

Do not place plants directly under the air flow as it is bad for the plants.

●

Please ensure that outdoor mounting frame is always stable, firm and

without defect. If not, the outdoor unit may collapse and cause danger.

●

Do not splash or direct water to the body of the unit when cleaning it as this

may cause short circuit.

●

Do not put water container (like vase) on the indoor unit to avoid water

dripping into the unit. Dripping water will damage the insulator inside the

unit and causes short-circuit.

●

When operating the unit with the door and windows opened, (the room humidity is always above

80%) and with the air deflector facing down or moving automatically for a long period of time,

water will condense on the air deflector and drips down occasionally. This will wet your furniture.

Therefore, do not operate under such condition for a long time.

●

If the amount of heat in the room is above the cooling capability of the unit (for example: more

people entering the room, using heating equipments and etc.), the preset room temperature

cannot be achieved.

●

Do not climb on the outdoor unit or put objects on it.

●

Please switch off the unit and turn off the circuit breaker during cleaning, the

high-speed fan inside the unit may cause danger.

●

Turn off the circuit breaker if the unit is not to be operated for a long period.

C

A

U

T

I

O

N

!

– 4 –

INDOOR UNIT

OUTDOOR UNIT

WIDTH (mm)

745

700

MODEL

RAS-25CNH2

RAC-25CNH2

HEIGHT (mm)

248

570

DEPTH (mm)

175

210

MODEL NAME AND DIMENSIONS

NAMES AND FUNCTIONS OF EACH PART

AIR FILTER

To prevent dust from coming into the indoor unit.

(Refer page 16)

POWER PLUG (NOT PROVIDED)

INDOOR UNIT INDICATORS

Light indicator showing the operating condition.

(Refer page 5)

FRONT PANEL (AIR INLET)

HORIZONTAL DEFLECTOR

●

VERTICAL

DEFLECTOR (AIR OUTLET)

(Refer page 12)

REMOTE CONTROL

Send out operation signal to the indoor unit. So as

to operate the whole unit.

(Refer page 6)

DRAIN PIPE

Condensed water drain to outside.

CONNECTING CORD

AIR INLET (BACK, LEFT SIDE)

AIR OUTLET

– 5 –

ENGLISH

INDOOR UNIT INDICATORS

TEMPORARY SWITCH

Use this switch to start and stop when the remote

controller does not work.

● By setting the temporary switch, the operation is done

in previously set operation mode.

● When the operation is done using the temporary switch

after the power source is turned off and turn on again,

the operation is done in automatic mode.

OPERATION INDICATOR

OPERATION LAMP

This lamp lights during operation.

The OPERATION LAMP flashes in the following cases

during heating.

(1) During preheating

For about 2–3 minutes after starting up.

(2) During defrosting

Defrosting will be performed about once an hour

when frost forms on the heat exchanger of the

outdoor unit, for 5–10 minutes each time.

TIMER LAMP

This lamp lights when the timer is working.

SIGNAL RECEIVER

There will be a beep sound when this receiver receives

signal from remote controller.

POWER SWITCH

– 6 –

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

■ This controls the operation function and timer setting of the room air conditioner. The range of

control is about 4 meters. If indoor lighting is controlled electronically, the range of control may be

shorter.

Precautions for Use

● Do not put the remote controller under

direct sunlight and high temperature.

● Do not drop it on the floor, and protect

it from water.

● If you press the FUNCTION button

during operation, the air conditioner may

stop for about 3 minutes for protection

before you can start it again.

You can use the remote controller by fixing it on the

wall with the accessory parts.

● Before fixing it,

make sure the

unit can be

controlled by the

remote control

unit at the fixing

position.

REMOTE

CONTROLLER

HOLDER

START/STOP Button

Press this button to start operation.

Press it again to stop operation.

SLEEP Button

Use this button to set the sleep timer.

( Page 10)

Reserve Button

Timer setting reservation.

OFF TIMER Button

Select the turn OFF time.

ON TIMER Button

Select the turn ON time.

Transmission Sign

The transmission sign blinks

when a signal has been send.

TEMPERATURE Button

Room temperuture setting.

Value will change quicker when

keep pressing.

( Page 7)

FAN SPEED Button

Select the fan speed for

cooling and heating mode.

( Page 8)

AUTO SWING Button

Control the angle of the

horizontal air deflector.

( Page 12)

CANCEL Button

Cancel timer reservation.

Signal Transmission

FUNCTION Button

Select the operation mode.

( Page 8)

C

˚

Hr.

HITACHI

°C

– 7 –

ENGLISH

AUTOMATIC OPERATION

■ The device will automatically determine the mode of operation, HEAT, COOL or DEHUMIDIFY,

depending on the initial room temperature. The selected mode of operation will not change when

the room temperature varies.

1

Press the (START/STOP) button

● Operation start with a “beep” sound.

Press the (START/STOP) button

● Make sure the (Automatic) mode have been selected by using

the (FUNCTION) button.

● The fan speed selector does not work at this operation.

STOP

Press the (ROOM TEMPERATURE) button

● Temperature setting change by 1°C for each 1 time press.

Up

Down

● You can raise or lower the temperature setting by a maximum of

3°C.

● The display does not indicate the preset temperature in the Automatic

mode. Device will receive the setting by a “beep”.

■ You can slightly adjust the room temperature.

1

°C

▲ ▲

■ CONDITION OF AUTOMATIC OPERATION

● The selected mode of operation will not change during the operation even though the room

temperature change.

Over 27°C COOL

23 ~ 27°C

FUNCTION

27°C

Slightly lower than the

room temperature

LOW

FAN SPEED

HIGH at start, LOW after

the preset temperature is

reached

-

DRY

-

INITIAL ROOM

TEMPERATURE (APPROX.)

TEMPERATURE

SETTING

Under 23°C HEAT 23°C

HIGH at start, MED or

LOW after the preset

temperature is reached

-

HITACHI

°C

HITACHI

°C

– 8 –

MANUAL OPERATION [Heating

●

Dehumidify

●

Cooling]

■ Please use under below condition when you want to set the function mode, room temperature and

fan speed by manually.

1

OPERATION MODE SELECTION

● Every time you press the button, the mode will change as the below

sequence

(Auto) [ (Heat) [ (Dry) [ (Cool)

2

ROOM TEMPERATURE SETTING

Up

Down

● The cooling operation does not start if the

temperature setting is higher than the current

room temperature.

3

FAN SPEED SETTING

● Every time you press the button, fan speed will change as

below sequence.

● HEATING : AUTO [ HIGH [ MED [ LOW

COOLING : ( [ [ [ )

● DEHUMIDIFYING : LOW (FIXED)

: ( )

4

Press the (START/STOP) button

● Operation start with a signal received sound “beep”.

Press the (START/STOP) button

● As the settings are stored in memory in the remote control unit, you

only have to press the (Start/Stop) button in order to use the

same setting next time.

STOP

HEATING

Outdoor Temperature

21°C below

DEHUMIDIFYING

Room Temperature

16°C above

COOLING

Outdoor Temperature

22°C above

°C

Heating 20~24°C

Dehumidify 20~26°C

Cooling 25~28°C

■ Recommend Temperature

▲ ▲

HITACHI

°C

HITACHI

°C

HITACHI

°C

}

HITACHI

°C

– 9 –

ENGLISH

TIMER RESERVATION

■ ON Timer and OFF Timer are available.

1

OFF TIME setting

● Select the OFF TIME by pressing the (OFF)

Button.

● Setting time will change according to the below

sequence when you press the button.

● The value change quicker if you keep pressing the

button.

OFF Timer Reservation

■ Operation stop at setting time

2

Press the (Reserve) button

● OFF TIMER reserved with a signal received sound

“beep”.

● The (OFF) Mark starts lighting instead of blinding.

0.5 1.0 1.5 9.5 10 11 12

0.5 hour interval 1 hour interval

1

ON TIME setting

● Select the ON TIMER by pressing the (ON)

Button.

● At the beginning of setting, time 6 hours was set.

● Setting time will change according to the below

sequence.

● The value change quicker if you keep pressing the

button.

ON Timer Reservation

0.5 1.0 1.5 9.5 10 11 12

0.5 hour interval 1 hour interval

1

Press the (Cancel) button

● As the time settings are stored in remote controller

memory, you only have to press the (Reserve)

button in order to use the same setting next time.

CANCELLATION of Timer Reservation

2

Press the (Reserve) button

● ON TIMER reserved with a signal received sound

“beep”.

● The (ON) Mark starts lighting instead of blinding.

o

■ Operation will start for setting

temperature at setting time (The starting

time may different depend on the room

temperature and set temperature).

Hr.

HITACHI

°C

Hr.

HITACHI

°C

Hr.

HITACHI

°C

Hr.

HITACHI

°C

Hr.

– 10 –

Press the (SLEEP) button, and the display changes as shown below.

HOW TO SET THE SLEEP TIMER

Mode

Sleep timer

Indication

1 hour 2 hours 3 hours 7 hours

Sleep timer off

44 44

1

Sleep Timer: The device will continue working for the designated

number of hours and then turn off.

Point the signal window of the remote controller toward the indoor

unit, and press the SLEEP button.

The timer information will be displayed on the remote controller.

The TIMER lamp lights with a beep from the indoor unit.

How to Cancel Reservation

Point the signal window of the remote controller toward the indoor unit, and press the (CANCEL)

button.

The (RESERVED) sign goes out with a beep and the (TIMER) lamp turns off on the indoor unit.

NOTE

If you set the sleep timer when the off-timer or

on/off-timer has been set earlier, the sleep timer

becomes effective instead of the off- or on/off-

timer set earlier.

Hr.

HITACHI

°C

Example: Setting 3 hours

sleep time.

– 11 –

ENGLISH

Cooling

“ ”

and

dehumidifying

“ ”

Explanation of the sleep timer

The device will control the FAN SPEED and room temperature automatically

so as to be quiet and good for people’s health.

You can set the sleep timer to turn off after 1, 2, 3 or 7 hours. The FAN

SPEED and room temperature will be controlled as shown below.

Function Operation

The settings of room temperature and circulation are not varied.

The FAN SPEED will be set to

LOW immediately.

Fan

“ ”

Heating

“ ”

The room temperature will be

controlled 5°C below the

temperature setting 30 minutes

after the setting of the sleep

timer. The FAN SPEED will be

set to LOW immediately.

Operation with the sleep timer

Sleep timer set

30 minutes later

1 hour later

3 hours later

7 hours

later

2 hours

later

5°C

Sleep

timer set

30 minutes later

3 hours later

7 hours later

2 hours

later

6 hours

later

The room temperature is kept

at about 12°C minimum.

The room temperature is kept

at about 25–28°C.

– 12 –

ADJUSTING THE AIR DEFLECTOR

1

Adjustment of the conditioned air in the upward and downward

directions.

According to operation, the horizontal air deflector is

automatically set to the proper angle suitable for each

operation. The deflector can be swing up and down and also

set to the desired angle using the “ (AUTO SWING)”

button. (If the angle of the deflector is changed, it will not

return to the auto-set position after operations start unless

the operation mode is switched.)

2

Adjustment of the conditioned air to the left and right.

Hold the vertical air deflector as shown in the figure and adjust

the conditioned air to the left and right.

● If the “ (AUTO SWING)” button is pressed once,

the horizontal air deflector swings up and down. If the

button is pressed again, the deflector stops in its current

position. Several seconds (about 6 seconds) may be

required before the deflector starts to move.

● Use the horizontal air deflector within the adjusting range

shown on the right.

● When the operation is stopped, the horizontal air deflector

moves and stops at the position where the air outlet

closes.

When cooling

dehumidifying

When heating

!

CAUTION

● In “Cooling” operation, do not keep the horizontal air

deflector swinging for a long time. Some dew may form

on the horizontal air deflector and some dew may drop

from it.

– 13 –

ENGLISH

HOW TO EXCHANGE THE BATTERIES IN THE REMOTE CONTROLLER

1

Remove the cover as shown in the figure and take out the

old batteries.

=

2

Install the new batteries.

The direction of the batteries should match the marks in the

case.

1. Do not use new and old batteries, or different kinds of batteries

together.

2. Take out the batteries when you do not use the remote controller

for 2 or 3 months.

CAUTION

Push and pull to the

direction of arrow

!

TEMPORARY SWITCH

Use this switch to start and stop when the

remote controller does not work.

● By setting the temporary switch, the

operation is done in previously set operation

mode.

● When the operation is done using the

temporary switch after the power source is

turned off and turn on again, the operation

is done in automatic mode.

POWER SWITCH

TEMPORARY SWITCH

– 14 –

Suitable Room Temperature Install curtain or blinds

Ventilation Effective Usage Of Timer

Do Not Forget To Clean The Air Filter

Please Adjust Suitable Temperature

For Baby And Children

Warning

Freezing temperature

is bad for health and a

waste of electric power.

!

It is possible to

reduce heat

entering the

room through

windows.

At night, please use the “OFF or ON timer

operation mode”, together with your wake up

time in the morning. This will enable you to

enjoy a comfortable room temperature. Please

use the timer effectively.

Dusty air filter will reduce the air volume and

the cooling efficiency. To prevent from wasting

electric energy, please clean the filter every 2

weeks.

Please pay attention to the room temperature

and air flow direction when operating the unit

for baby, children and old folks who have

difficulty in movement.

Caution

Do not close the room for a long period of

time. Occasionally open the door and windows

to allow the

entrance of

fresh air.

!

THE IDEAL WAYS OF OPERATION

– 15 –

ENGLISH

FOR USER’S INFORMATION

The Air Conditioner And The Heat Source In The Room

After Power Failure

Not Operating For A Long Time

When Lightning Occurs

Caution

If the amount of heat in the room is above the cooling

capability of the air conditioner (for example: more

people entering the room, using heating equipments

and etc.), the preset room temperature cannot be

achieved.

!

When the power is resumed after a power failure,

the indoor unit will still remain “OFF”. To operate the

unit, please press the “ON/OFF” button again.

When the indoor unit is not to be used for a long

period of time, please switch off the power from the

mains. If the power from mains remains “ON”, the

indoor unit still consumes about 8W in the operation

control circuit even if it is in “OFF” mode.

Warning

To protect the whole unit during lightning, please

stop operating the unit and remove the plug from the

socket.

!

OFF

Operate

After power

failure

– 16 –

MAINTENANCE

INSTALLATION METHOD

REMOVING METHOD

Air filter

Air cleansing and

deodorizing filter

!

Before the cleaning, stop operation and disconnect the power supply.

1. AIR FILTER

Clean the air filter, as it removes dust inside the room. In case the air filter is full of dust, the air flow

will decrease and the cooling capacity will be reduced. Further, noise may occur. Be sure to clean the

filter following the procedure below.

NOTE:

● Air cleansing and deodorizing filter should be cleaned every month or sooner if noticeable loading

occurs. When used overtime, it may loose its deodorizing function. For maximum performance,

it is recommended to replace it every 3-6 months depending on application requirements.

PROCEDURE

CAUTION

● Do not wash with hot water at more than 40°C. The filter may shrink.

● When washing it, shake off moisture completely and dry it in the shade; do not expose it directly

to the sun. The filter may shrink.

● Do not use detergent on the air cleansing and deodorizing filter as some detergent may deteriorate

the filter electrostatic performance.

Open the front panel and remove the filter

● Gently lift and remove the air cleansing and

deodorizing filters from the air filter frame.

1

● Re-insert the air cleansing and deodorizing

filters to the filter frame. Set the filter with

"FRONT" mark facing front, and slot them

into the original state.

● After attaching the filter, push the front panel

at three arrow portions as shown in figure

and close it.

3

● Vacuum dust from the air filter and air

cleansing and deodorizing filters using

vacuum cleaner. If there is too much dust,

rinse under running tap water and gently

brush it with soft bristle brush. Allow filters to

dry in shade.

2

!

– 17 –

ENGLISH

ATTACHING THE AIR CLEANSING AND DEODORIZING FILTERS

Before installation, be sure to stop the operation by using the remote controller.

Claws (8 places)

Make sure the “FRONT” is facing back side

Claws

Front cover

Front panel

Air filter

1

Open the front panel.

● Pull up the front panel by holding it at both sides

with both hands.

2

Remove the filter.

● Push the filter upward to release the claws and

pull out the filter.

3

Attaching the air cleansing and deodorizing filters

to the filter.

● Attach the air cleansing and deodorizing filters to

the frame by gently compress its both sides and

release after insertion into filter frame.

4

Attach the filters.

● Attach the filters by ensuring that the surface written

“FRONT” is facing front.

● After attaching the filters, push the front panel at

three arrow portion as shown in figure and close it.

!

CAUTION

Do not bend the air cleansing

and deodorizing filter as it may

cause damage to the structure.

NOTE

● In case of removing the air cleansing and deodorizing filters, please follow the above procedures.

● The cooling capacity is slightly weakened and the cooling speed becomes slower when the air cleansing

and deodorizing filters are used. So, set the fan speed to "HIGH" when using it in this condition.

● Air cleansing and deodorizing filters are washable and reusable up to 20 times by using vacuum cleaner

or water rinse under running tap water. Type number for this air cleansing filter is <SPX-CFH5>. Please

use this number for ordering when you want to renew it.

● Do not operate the air conditioner without filter. Dust may enter the air conditioner and fault may occur.

Frame

– 18 –

2. Washable Front Panel

● The front panel remove and can wash with clean

water in whole.

Wash it with a soft sponge.

After using neutral detergent, wash thoroughly with

clean water.

● When it is not removed, wipe it with a soft dry

cloth. Wipe the remote controller thoroughly with a

soft dry cloth.

● Wipe the water thoroughly.

If the water remains at indicators or signal receiver

of indoor unit, it causes trouble.

Method to remove of the suction grille.

Be sure to hold the suction grille with both hands

to detach and attach it.

!

CAUTION

● Do not splash or direct water to the body of the unit when cleaning

it as this may cause short circuit.

● Never use hot water (above 40°C), benzine, gasoline, acid, thinner or

a brush, because they will damage the plastic surface and the coating.

Removing the Front Panel

Arm

● When the front panel is fully opened with

both hands, push the right arm to the inside

to release it, and while closing the front panel

slightly, put it out forward.

Attaching the Front Panel

● Move the projections of the left and right

arms into the Flanges in the unit and

securely insert them into the holes.

Projection

Hole

Flange

– 19 –

ENGLISH

3. MAINTENANCE AT BEGINNING OF LONG OFF PERIOD

● Running the unit setting the operation mode to

(COOL), the temperature to 32°C and the fan speed

to HI for about half a day on a fine day, and dry the

whole of the unit.

● Disconnect the power plug.

1

2

3

REGULAR INSPECTION

PLEASE CHECK THE FOLLOWING POINTS EVERY EITHER HALF YEARLY OR YEARLY.

CONTACT YOUR SALES AGENT SHOULD YOU NEED ANY HELP.

Is the plug of power line firmly plugged into the socket?

(Please ensure no loose contact between them).

Is the earth line disconnected or broken?

Is the mounting frame seriously affected by rust and is the

outdoor unit tilted or unstable?

Air

Blow

Confirm

– 20 –

AFTER SALE SERVICE AND WARRANTY

WHEN ASKING FOR SERVICE, CHECK THE FOLLOWING POINTS.

When it does not operate

● Is the fuse all right?

● Is the voltage extremely high or low?

● Is the circuit breaker “ON”?

● Is the air filter blocked with dust?

● Does sunlight fall directly on the outdoor unit?

● Is the air flow of the outdoor unit obstructed?

● Are the doors or windows opened, or is there any source of

heat in the room?

● Is the set temperature suitable?

CONDITION CHECK THE FOLLOWING POINTS

Notes

● In quiet operation or stopping the operation, the following phenomena

may occassionally occur, but they are not abnormal for the operation.

(1) Slight flowing noise of refrigerant in the refrigerating cycle.

(2) Slight rubbing noise from the fan casing which is cooled and then

gradually warmed as operation stops.

● The odor will possibly be emitted from the room air conditioner because

the various odor, emitted by smoke, foodstuffs, cosmetics and so on,

sticks to it. So please clean the air filter and the evaporator regularly to

reduce the odor.

●

Please contact your sales agent immediately if the air conditioner still fails to operate normally after the above

inspections. Inform your agent of the model of your unit, production number, date of installation. Please also

inform him regarding the fault.

●

Power supply shall be connected at the rated voltage, otherwise the unit will be broken or could not reach the

specified capacity.

When it does not cool well

When it does not hot well

La page charge ...

Hitachi RAC-25CNH2 Manuel utilisateur

Hitachi RAC-25CNH2 Manuel utilisateur

dans d''autres langues

Documents connexes