Sony CDX-CA705M Manuel utilisateur

Marque: Sony

Modèle: CDX-CA705M

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

CDX-CA720X

Operating Instructions

Mode d’emploi

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record these numbers in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. CDX-CA720X/CA700X/CA705M Serial No.

CDX-CA720X

CDX-CA700X

CDX-CA705M

For installation and connections, see the supplied installation/connections manual.

En ce qui concerne l’installation et les connexions, consulter le manuel

d’installation/raccordement fourni.

3-237-887-11 (1)

Compact Disc

Player

CDX-CA705M only:

Welcome !

Thank you for purchasing this Sony Compact

Disc Player. You can enjoy its various features

even more with:

• Optional CD/MD units (both changers and

players)*

• CD TEXT information (displayed when a CD

TEXT disc*

is played).

• Supplied controller accessory

Card remote commander RM-X118

• Optional controller accessory

Rotary commander RM-X4S

*1 This unit works with Sony products only.

*2 A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name,

and track names. This information is recorded on

the disc.

Warning

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

–

Reorient or relocate the receiving antenna.

–

Increase the separation between the equipment

and receiver.

–

Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

–

Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

The use of optical instruments with this product

will increase eye hazard.

CAUTION

This label is located on the bottom of the

chassis.

CAUTION INVISIBLE

DO NOT STARE INTO BEAM OR

VIEW DIRECTLY WITH OPTICAL INSTRUMENTS

LASER RADIATION WHEN OPEN

This label is located on the drive unit’s internal

chassis.

The “XM Ready” logo indicates that this product

will control a Sony XM tuner module (sold

separately).

Please see your nearest authorized Sony dealer

for details on the XM tuner module.

For instructions on XM tuner operation, please

refer to the XM tuner module’s included

instruction manual.

Table of Contents

Location of controls. . . . . . . . . . . . . . . . . . . . 4

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Notes on discs . . . . . . . . . . . . . . . . . . . . . . . . 6

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . 7

Detaching the front panel . . . . . . . . . . . . . . . 8

Setting the clock . . . . . . . . . . . . . . . . . . . . . . 9

CD Player

CD/MD Unit (optional)

Playing a disc. . . . . . . . . . . . . . . . . . . . . . . . . 9

Display items. . . . . . . . . . . . . . . . . . . . . . . . 10

Playing tracks repeatedly

— Repeat Play . . . . . . . . . . . . . . . . . . . . 11

Playing tracks in random order

— Shuffle Play . . . . . . . . . . . . . . . . . . . . 11

Labeling a CD

— Disc Memo*. . . . . . . . . . . . . . . . . . . . 11

Locating a disc by name

— List-up* . . . . . . . . . . . . . . . . . . . . . . . 12

* Functions available with optional CD/MD unit

Radio

Storing stations automatically

— Best Tuning Memory (BTM). . . . . . . 13

Receiving the stored stations. . . . . . . . . . . . 13

Storing only the desired stations . . . . . . . . . 14

Storing station names

— Station Memo. . . . . . . . . . . . . . . . . . . 14

Tuning in a station through a list

— List-up . . . . . . . . . . . . . . . . . . . . . . . . 15

Other Functions

Using the rotary commander. . . . . . . . . . . . 16

Adjusting the sound characteristics . . . . . . 17

Quickly attenuating the sound . . . . . . . . . . 17

Changing the sound and display settings

— Menu . . . . . . . . . . . . . . . . . . . . . . . . . 18

Setting the equalizer (EQ7). . . . . . . . . . . . . 19

Setting the Dynamic Soundstage Organizer

(DSO). . . . . . . . . . . . . . . . . . . . . . . . . . . 19

MP3 playable CD Unit (optional)

Listening to an MP3 file . . . . . . . . . . . . . . . 20

Display items . . . . . . . . . . . . . . . . . . . . . . . 20

Playing tracks repeatedly

— Repeat Play . . . . . . . . . . . . . . . . . . . . 21

Playing tracks in random order

— Shuffle Play. . . . . . . . . . . . . . . . . . . . 21

Additional Information

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 22

Removing the unit. . . . . . . . . . . . . . . . . . . . 23

Specifications . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . 25

Error displays/Messages. . . . . . . . . . . . . . . 26

Location of controls

Refer to the pages listed for details.

a DSO button 19

b MODE button

To change the operation.

c Z (eject) button (located on the front side

of the unit, behind the front panel) 9

d DSPL (display mode change) button

e Volume control dial

f Display window

g MENU button

To display the menus.

h LIST button 12, 15

i OPEN button 8, 9

j OFF (Stop/Power off) button*

8, 9

k RESET button (located on the front side of

the unit, behind the front panel) 7

l SOURCE (Power on/Radio/CD/MD)

button

To select the source.

m SCRL (scroll) button 10

n Frequency select switch (located on

the bottom of the unit)*

The AM (FM) tuning interval is factory-set

to the 10 k (200 k) position. Make sure that

the 9 k (50 k) position is selected.

o Receptor for the card remote

commander

p SOUND button 17

q ENTER button

To enter a setting.

r EQ7 button 19

*1 Warning when installing in a car without

an ACC (accessory) position on the

ignition switch

After turning off the ignition, be sure to press

(OFF) on the unit for 2 seconds to turn off the

clock display.

Otherwise, the clock display does not turn off

and this causes battery drain.

*2 CDX-CA705M only

CDX-CA720X/CA700X/CA705M

SOURCE

DSO

SEEK

EQ7

s DISC/PRESET buttons (+/–)

To receive preset stations, change the disc*

and select a menu.

* When an optional CD/MD unit is connected.

t SEEK buttons (–/+)

To skip tracks, fast-forward, reverse a track,

tune in stations automatically, find a station

manually, and select a setting.

The corresponding buttons of the card

remote commander control the same

functions as those on this unit.

a DSPL button

b Number buttons

(1) REP

(2) SHUF

To store stations, receive stored stations.

c DSO button

d MENU button

e SOURCE button

f SEEK (</,) buttons

g SOUND button

h OFF button

i VOL (+/–) buttons

j EQ7 button

k MODE button

l LIST button

m DISC (M/m) buttons

n ENTER button

o ATT button

Note

If the unit is turned off by pressing (OFF) for

2 seconds, it cannot be operated with the card remote

commander unless (SOURCE) on the unit is pressed,

or a disc is inserted to activate the unit first.

Tip

See “Replacing the lithium battery” on page 22 for

details on how to replace the batteries.

SEEK

EQ7

SEEK

(SEEK)

(–): to select

leftwards/

(SEEK)

(+): to select

rightwards/

(DISC/PRESET)

(+): to select upwards

In menu mode, the currently selectable button (s)

of these four are indicated with a “ M” in the display.

(DISC/PRESET)

(–): to select downwards

Card remote commander RM-X118

DISC

–

ATTOFF

REP SHUF

DSPL

MODE

SOURCE

DISC

SEEK

–

SOUND

ENTER

LIST

EQ7DSO

VOL

Precautions

• If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

• Power antennas will extend automatically

while the unit is operating.

If you have any questions or problems

concerning your unit that are not covered in this

manual, please consult your nearest Sony dealer.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit

will not operate properly. In such a case, remove

the disc and wait for about an hour until the

moisture has evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

Notes on discs

• To keep the disc clean, do not touch the surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc

magazines when not in use.

Do not subject the discs to heat/high

temperature. Avoid leaving them in parked cars

or on dashboards/rear trays.

• Do not attach labels, or use discs with sticky

ink/residue. Such discs may stop spinning

when used, causing a malfunction, or may ruin

the disc.

• Do not use discs with any labels or stickers

attached.

The following malfunctions may result from

using such discs:

– Inability to eject a disc (due to a label or

sticker peeling off and jamming the eject

mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to

heat shrinking of a sticker or label causing a

disc to warp.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do

not use such discs.

• You cannot play 8 cm CDs.

• Before playing, clean the discs with a

commercially available cleaning cloth. Wipe

each disc from the centre out. Do not use

solvents such as benzine, thinner, commercially

available cleaners, or antistatic spray intended

for analog discs.

Notes on CD-R/CD-RW discs

• You can play CD-Rs (recordable CDs)/CD-

RWs (rewritable CDs) designed for audio use

on this unit.

Look for these marks to distinguish CD-Rs/

CD-RWs for audio use.

These marks denote that a disc is not for audio

use.

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the

condition of the disc) may not play on this unit.

• You cannot play a CD-R/a CD-RW that is not

finalized*.

* A process necessary for a recorded CD-R/CD-RW

disc to be played on the audio CD player.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Remove the front panel and press the RESET

button with a pointed object, such as a ball-point

pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

RESET button

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

Caution alarm

If you turn the ignition switch to the OFF

position without removing the front panel, the

caution alarm will beep for a few seconds.

If you connect an optional amplifier and do not

use the built-in amplifier, the beep sound will be

deactivated.

1 Press (OFF)*.

CD/MD playback or radio reception stops

(the key illumination and display remain on).

* If your car has no ACC position on the ignition

switch, be sure to turn the unit off by pressing

(OFF) for 2 seconds to avoid car battery drain.

2 Press (OPEN), then slide the front

panel to the right, and gently pull out

the left end of the front panel.

Notes

• If you detach the panel while the unit is still turned

on, the power will turn off automatically to prevent

the speakers from being damaged.

• Do not drop or put excessive pressure on the front

panel and its display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in parked

car or on a dashboard/rear trays.

Tip

When carrying the front panel with you, use the

supplied front panel case.

Attaching the front panel

Place hole A of the front panel onto the spindle

B on the unit, then lightly push the left side in.

Press (SOURCE) (or insert a CD) to operate the

unit.

Note

Do not put anything on the inner surface of the front

panel.

Setting the clock

The clock uses a 12-hour digital indication.

Example: To set the clock to 10:08

1 Press (MENU), then press either side

of (DISC/PRESET) repeatedly until

“CLOCK” appears.

1 Press (ENTER).

The hour indication flashes.

2 Press either side of (DISC/PRESET)

to set the hour.

3 Press the (+) side of (SEEK).

The minute indication flashes.

4 Press either side of (DISC/PRESET)

to set the minute.

2 Press (ENTER).

The clock starts. After the clock setting is

completed, the display returns to normal play

mode.

Tip

When D.INFO mode is set to ON, the time is always

displayed (page 18).

CD Player

CD/MD Unit (optional)

In addition to playing a CD with this unit, you

can also control external CD/MD units.

If you connect MP3 playable CD units (eg. MP3

CD changer), you can play MP3 files;

compressed audio files with quality sound. See

“MP3 playable CD Unit (optional)” on page 20.

Note

If you connect an optional CD unit with the CD TEXT

function, the CD TEXT information will appear in the

display when you play a CD TEXT disc.

Playing a disc

(With this unit)

1 Press (OPEN) and insert the disc

(labeled side up).

2 Close the front panel.

Playback starts automatically.

If a disc is already inserted, press (SOURCE)

repeatedly until “CD” appears to start playback.

To Press

Stop playback (OFF)

Eject the disc (OPEN) then Z

Skip tracks

– Automatic

Music Sensor

(SEEK) (./>)

[once for each track]

Fast-forward/

reverse

– Manual Search

(SEEK) (m/M)

[hold to desired point]

continue to next page t

Notes

• While the first/last track on the disc is playing, if

(SEEK) is pressed, playback skips to the last/first

track of the disc.

• When the last track on the disc is over, playback

restarts from the first track of the disc.

• With an optional unit connected, playback of the

same source will continue on to the optional CD/MD

unit.

(With optional unit)

1 Press (SOURCE) repeatedly to select

“CD” or “MD (MS*).”

2 Press (MODE) repeatedly until the

desired unit appears.

Playback starts.

*MS: MG Memory Stick System-up Player MGS-X1

Cautions when connecting MGS-X1 and MD unit(s)

This unit recognizes MGS-X1 as an MD unit.

• When you want to play MGS-X1, press (SOURCE) to

select “MS” or “MD.” If “MS” appears in the source

display, MGS-X1 starts to play. If “MD” appears in

the source display, press (MODE) to select “MS,” to

start playback.

• When you want to play an MD unit, press (SOURCE)

to select “MD” or “MS.” If your desired MD unit

appears in the source display, it starts to play. If “MS”

or another MD unit appears in the source display,

press (MODE) to select your desired MD unit, to

start playback.

Display items

When the disc/track changes, any prerecorded

title*

of the new disc/track is automatically

displayed (if the Auto Scroll function is set to

“ON,” names exceeding 8 characters will be

scrolled (page 18)).

*1 When pressing (DSPL), “NO NAME” indicates that

there is no Disc Memo (page 11) or prerecorded

name to display.

*2 Only for CD TEXT discs with the artist name.

Notes

• Some characters cannot be displayed.

• For some CD TEXT discs with very many

characters, information may not scroll.

• This unit cannot display the artist name for each

track of a CD TEXT disc.

Tip

When A.SCRL (Auto Scroll) is set to OFF and the disc/

track name is changed, the disc/track name does not

scroll.

To Press

Skip discs

–Disc selection

(DISC/PRESET) (+/–)

To Press

Switch display

item

(DSPL)

Scroll display item (SCRL)

Displayable items

• Track number/ Elapsed playing

time

•Disc name*

/artist name*

•Track title*

Disc number

Displayable items

• Music Source

•Clock

• Function

Playing tracks repeatedly

— Repeat Play

The disc in the main unit will repeat a track or

the entire disc when it reaches the end. For repeat

play, you can select:

• REP-TRACK — to repeat a track.

• REP-DISC* — to repeat a disc.

* Available only when one or more optional CD/MD

units are connected.

During playback, press (1) on the

card remote commander repeatedly

until the desired setting appears in the

display.

Repeat Play starts.

To return to normal play mode, select “REP-

OFF.”

Playing tracks in random

order

— Shuffle Play

You can select:

• SHUF-DISC — to play the tracks on the

current disc in random order.

• SHUF-CHGR*

— to play the tracks in the

current optional CD (MD) unit in random

order.

•SHUF-ALL*

— to play all the tracks in all the

connected CD (MD) units (including this unit)

in random order.

*1 Available only when one or more optional CD (MD)

units are connected.

*2 Available only when one or more optional CD units,

or two or more optional MD units are connected.

During playback, press (2) on the

card remote commander repeatedly

until the desired setting appears in the

display.

Shuffle Play starts.

To return to normal play mode, select “SHUF-

OFF.”

Note

“SHUF-ALL” will not shuffle tracks between CD units

and MD units.

Labeling a CD

— Disc Memo (For a CD unit with the

CUSTOM FILE function)

You can label each disc with a custom name

(Disc Memo). You can enter up to 8 characters

for a disc. If you label a CD, you can locate the

disc by name (page 12).

1 Start playing the disc you want to label

in a CD unit with the CUSTOM FILE

function.

2 Press (MENU), then press either side

of (DISC/PRESET) repeatedly until

“NAMEEDIT” appears.

3 Press (ENTER).

The unit will repeat the disc during the

labeling procedure.

4 Enter the characters.

1 Press the (+)*

side of

(DISC/PRESET) repeatedly to select

the desired character.

A t B t C ... t 0 t 1 t 2 ... t +

t – t

... t _*

t A

*1 For reverse order, press the (–) side of

(DISC/PRESET).

*2 (blank space)

2 Press the (+) side of (SEEK) after

locating the desired character.

If you press the (–) side of (SEEK), you

can move back to the left.

3 Repeat steps 1 and 2 to enter the

entire name.

5 To return to normal CD play mode,

press (ENTER).

continue to next page t

Tips

• Simply overwrite or enter “

_” to correct or erase a

name.

• There is another way to start labeling a CD: Press

(LIST) for 2 seconds instead of performing steps 2

and 3. You can also complete the operation by

pressing (LIST) for 2 seconds instead of step 5.

• You can label CDs on a unit without the CUSTOM

FILE function if that unit is connected along with a

CD unit that has the function. The Disc Memo will be

stored in the memory of the CD unit with the

CUSTOM FILE function.

Note

REP-TRACK/shuffle play is suspended until the Name

Edit is complete.

Viewing the Disc Memo

As a display item, the Disc Memo always takes

priority over any original CD TEXT information.

Tip

To find out about other items that can be displayed,

see page 10.

Erasing the Disc Memo

1 Press (SOURCE) repeatedly to select

“CD.”

2 Press (MODE) repeatedly to select the

CD unit storing the Disc Memo.

3 Press (MENU), then press either side

of (DISC/PRESET) repeatedly until

“NAME DEL” appears.

4 Press (ENTER).

The stored names will appear.

5 Press either side of (DISC/PRESET)

repeatedly to select the disc name you

want to erase.

The stored names will appear.

6 Press (ENTER) for 2 seconds.

The name is erased.

Repeat steps 5 and 6 if you want to erase

other names.

7 Press (MENU) twice.

The unit returns to normal CD play mode.

Notes

• When the Disc Memo for a CD TEXT disc is erased,

the original CD TEXT information is displayed.

• If you cannot find the Disc Memo you want to erase,

try selecting a different CD unit in step 2.

Locating a disc by name

— List-up (For a CD unit with the CD TEXT/

CUSTOM FILE function, or an MD unit)

You can use this function for discs that have been

assigned custom names*

or for CD TEXT

discs*

*1 Locating a disc by its custom name: when you

assign a name for a CD (page 11) or an MD.

*2 Locating discs by the CD TEXT information: when

you play a CD TEXT disc on a CD unit with the CD

TEXT function.

1 Press (LIST).

The name assigned to the current disc appears

in the display.

2 Press either side of (DISC/PRESET)

repeatedly until you find the desired

disc.

3 Press (ENTER) to play the disc.

Note

Some letters cannot be displayed (exception: Disc

Memo).

To Press

View (DSPL) during CD/CD

TEXT disc playback

Radio

The unit can store up to 6 stations per band

(FM1, FM2, FM3, AM1, and AM2).

Caution

When tuning in stations while driving, use Best

Tuning Memory to prevent accidents.

Storing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals within the selected band, and stores them

in the order of their frequency.

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (MENU), then press either side

of (DISC/PRESET) repeatedly until

“BTM” appears.

4 Press (ENTER).

A beep sounds when the setting is stored.

Notes

• If only a few stations can be received due to weak

signals, some number buttons will retain their former

settings.

• When a number is indicated in the display, the unit

starts storing stations from the one currently

displayed.

Receiving the stored stations

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6))

on the card remote commander on

which the desired station is stored.

Tip

Press either side of (DISC/PRESET) to receive the

stations in the order they are stored in the memory

(Preset Search function).

If preset tuning does not work

Press either side of (SEEK) to search

for the station (automatic tuning).

Scanning stops when the unit receives a

station. Repeat until the desired station is

received.

Tips

• If automatic tuning stops too frequently, turn on the

Local Seek to limit seek to stations with stronger

signals (see “Changing the sound and display

settings” on page 18).

• If you know the frequency of the station you want to

listen to, press and hold either side of (SEEK) to

locate the approximate frequency, then press

(SEEK) repeatedly to fine adjust to the desired

frequency (manual tuning).

If FM stereo reception is poor

Select monaural reception mode

(see “Changing the sound and display

settings” on page 18).

The sound improves, but becomes monaural

(“ST” disappears).

Note

If interference occurs, this unit will automatically

narrow the reception frequency to eliminate noise (IF

AUTO function). In such cases, some FM stereo

broadcasts may become monaural while in the stereo

reception mode.

Tips

• To always hear FM stereo broadcasts in stereo, you

can change the IF AUTO setting and widen the

frequency signal reception (see “Changing the

sound and display settings” on page 18). Note that

some interference may occur in this setting.

• If FM broadcasts are difficult to hear, set DSO to

OFF (page 19).

Storing only the desired

stations

You can manually preset the desired stations on

any chosen number button.

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press either side of (SEEK) to tune in

the station that you want to store.

4 Press the desired number button ((1)

to (6)) on the card remote commander

for 2 seconds until “MEM” appears.

The number button indication appears in the

display.

Note

If you try to store another station on the same number

button, the previously stored station will be erased.

Storing station names

— Station Memo

You can assign a name to each radio station and

store it in memory. The name of the station

currently tuned in appears in the display. You can

assign a name using up to 8 characters for a

station.

Storing the station names

1 Tune in a station whose name you

want to store.

2 Press (MENU), then press either side

of (DISC/PRESET) repeatedly until

“NAMEEDIT” appears.

3 Press (ENTER).

4 Enter the characters.

1Press the (+)*

side of

(DISC/PRESET) repeatedly to select

the desired character.

A t B t C ... t 0 t 1 t 2 ... t +

t – t

... t _*

t A

*1 For reverse order, press the (–) side of

(DISC/PRESET).

*2 (blank space)

2Press the (+) side of (SEEK) after

locating the desired character.

If you press the (–) side of (SEEK), you can

move back to the left.

3Repeat steps 1 and 2 to enter the

entire name.

5 Press (ENTER).

Tips

• Simply overwrite or enter “

_” to correct or erase a

name.

• There is another way to start storing station names:

Press (LIST) for 2 seconds instead of performing

steps 2 and 3. You can also complete the operation

by pressing (LIST) for 2 seconds instead of step 5.

Erasing the station name

1 During radio reception, press (MENU),

then press either side of

(DISC/PRESET) repeatedly until “NAME

DEL” appears.

2 Press (ENTER).

3 Press either side of (DISC/PRESET)

repeatedly to select the station whose

name you want to erase.

4 Press (ENTER) for 2 seconds.

The name is erased.

Repeat steps 3 to 4 if you want to erase other

names.

5 Press (MENU) twice.

The unit returns to normal radio reception

mode.

Note

If you have already erased all of the station names,

“NO DATA” appears in step 4.

Tuning in a station through a

list

— List-up

1 During radio reception, press (LIST)

momentarily.

The frequency or the name assigned to the

current station appears in the display.

2 Press either side of (DISC/PRESET)

repeatedly until you find the desired

station.

If no name is assigned to the selected station,

the frequency appears in the display.

3 Press (ENTER) to tune in the desired

station.

Other Functions

You can also control the unit (and optional CD/

MD units) with a rotary commander (optional).

Using the rotary commander

First, attach the appropriate label depending on

how you want to mount the rotary commander.

The rotary commander works by pressing

buttons and/or rotating controls.

By pressing buttons

*1 Only if the corresponding optional equipment is

connected.

*2 If your car has no ACC (accessory) position on the

ignition key switch, be sure to press (OFF) for

2 seconds to turn off the clock indication after

turning off the ignition.

By rotating the control

Rotate and release to:

– Skip tracks.

– Tune in stations automatically.

Rotate, hold, and release to:

– Fast-forward/reverse a track.

– Find a station manually.

By pushing in and rotating the control

Push in and rotate the control to:

– Receive preset stations.

– Change the disc*.

* When an optional CD/MD unit is connected.

Press To

(SOURCE) Change source

(radio/CD/MD*

)/Power on

(MODE) Change operation

(radio band/CD unit/MD*

unit)

(ATT) Attenuate sound

(OFF)*

Stop playback or radio

reception/Power off

(SOUND) Adjust the sound menu

(DSPL) Change the display item

SOUND

DSPL

MODE

SOUND

DSPL

MODE

OFF

Rotate the VOL control

to adjust the volume.

(SOURCE)

(SOUND)

(ATT)

(DSPL)

(OFF)

(MODE)

SEEK/AMS

control

PRESET/DISC

control

Changing the operative direction

The operative direction of controls is factory-set

as shown below.

If you need to mount the rotary commander on

the right hand side of the steering column, you

can reverse the operative direction.

Press (SOUND) for 2 seconds while

pushing the VOL control.

Tip

You can also change the operative direction of these

controls with the unit (page 18).

Adjusting the sound

characteristics

You can adjust the bass, treble, balance and fader.

1 Select the item you want to adjust by

pressing (SOUND) repeatedly.

Each time you press (SOUND), the item

changes as follows:

BAS (bass) t TRE (treble) t

BAL (left-right) t FAD (front-rear)

2 Adjust the selected item by pressing

either side of (SEEK).

When adjusting with the rotary commander,

press (SOUND) and rotate the VOL control.

Note

Adjust within 3 seconds after selecting the item.

Quickly attenuating the

sound

(With the rotary commander or the card

remote commander)

Press (ATT) on the rotary commander

or card remote commander.

After “ATT-ON” momentarily appears,

“ATT” appears in the display.

To restore the previous volume level, press

(ATT) again.

Tip

When the interface cable of a car telephone is

connected to the ATT lead, the unit decreases the

volume automatically when a telephone call comes in

(Telephone ATT function).

To increase

To decrease

Changing the sound and

display settings

— Menu

The following items can be set:

SET (Set Up)

• CLOCK (page 9)

• BEEP — to turn the beeps on or off.

• RM (Rotary Commander) — to change the

operative direction of the controls of the rotary

commander.

– Select “NORM” to use the rotary commander

at the factory-set position.

– Select “REV” when you mount the rotary

commander on the right side of the steering

column.

• P.OUT-4.0V/5.5V— to change the pre-out of

the power amplifier to 4.0V or 5.5V. Selectable

only when the unit is turned off. (CDX-

CA720X only)

Note

If the volume is turned up very high when connected

to a power amplifier, the sound may be distorted. In

this case, set P.OUT to “4.0V.”

DSPL (Display)

• D.INFO (Dual Information) — to display the

clock and the play mode at the same time (ON).

• M.DSPL (Motion Display) — to select the

Motion Display mode from “1,” “2,” and

“OFF.”

– Select “1” to show decoration patterns in the

display and activate Demo display.

– Select “2” to show decoration patterns in the

display and deactivate Demo display.

– Select “OFF” to deactivate the Motion

Display.

• A.SCRL (Auto Scroll)

– Select “ON” to scroll all automatically

displayed names exceeding 8 characters.

– When A.SCRL is set to off and the disc/track

name is changed, the disc/track name does

not scroll.

• DIM (Dimmer) — to change the brightness of

the display. (CDX-CA720X only)

– Select “ON” to dim the display.

– Select “OFF” to deactivate the Dimmer.

P/M (Play Mode)

• LOCAL ON/OFF (Local seek mode) (page 13)

– Select “ON” to only tune into stations with

stronger signals.

• MONO ON/OFF (Monaural mode) (page 13)

– Select “ON” to hear FM stereo broadcast in

monaural. Select “OFF” to return to normal

mode.

• IF AUTO/WIDE (page 13)

SND (Sound)

• EQ7 TUNE (page 19) — to adjust the equalizer

curve.

• LOUD (Loudness) — to enjoy bass and treble

even at low volumes. The bass and treble will

be reinforced.

1 Press (MENU).

To set A.SCRL, press (MENU) during CD/

MD playback.

2 Press either side of (DISC/PRESET)

repeatedly until the desired item

appears.

3 Press the (+) side of (SEEK) to select

the desired setting (Example: “ON” or

“OFF”).

4 Press (ENTER).

After the mode setting is completed, the

display returns to normal play mode.

Note

The displayed item will differ depending on the source.

Tip

You can easily switch among categories (“SET,”

“DSPL,” “P/M,” “SND,” and “EDIT”) by pressing either

side of (DISC/PRESET) for 2 seconds.

Setting the equalizer (EQ7)

You can select an equalizer curve for 7 music

types (XPLOD, VOCAL, CLUB, JAZZ, NEW

AGE, ROCK, CUSTOM, and OFF (equalizer

OFF)).

You can store and adjust the equalizer settings

for frequency and level.

Selecting the equalizer curve

1 Press (SOURCE) to select a source

(radio, CD, or MD).

2 Press (EQ7) repeatedly until the

desired equalizer curve.

Each time you press (EQ7), the item

changes.

To cancel the equalizing effect, select “OFF.”

After 3 seconds, the display returns to the

normal playback mode.

Adjusting the equalizer curve

1 Press (MENU).

2 Press either side of (DISC/PRESET)

repeatedly until “EQ7 TUNE” appears,

then press (ENTER).

3 Press either side of (SEEK) to select

the desired equalizer curve, then

press (ENTER).

Each time you press (SEEK), the item

changes.

4 Select the desired frequency and level.

1 Press either side of (SEEK) to select

the desired frequency.

Each time you press (SEEK), the

frequency changes.

62 Hz y 157 Hz y 396 Hz y 1kHz

y 2.5kHz y 6.3kHz y 16kHz

2 Press either side of (DISC/PRESET)

to adjust the desired volume level.

The volume level is adjustable in 1 dB

steps from –10 dB to +10 dB.

To restore the factory-set equalizer curve,

press (ENTER) for 2 seconds.

5 Press (MENU) twice.

When the effect setting is complete, the

normal playback mode appears.

Setting the Dynamic

Soundstage Organizer (DSO)

If your speakers are installed into the lower part

of the doors, the sound will come from below

and may not be clear.

The DSO (Dynamic Soundstage Organizer)

function creates a more ambient sound as if there

were speakers in the dashboard (virtual

speakers).

You can store the DSO setting for each source.

1 Press (SOURCE) to select a source

(radio, CD, or MD).

2 Press (DSO) repeatedly until “DSO-

ON” appears.

To cancel the DSO function, select “DSO-OFF”

in step 2.

Notes

• Depending on the type of car interior or type of

music, DSO may not have a desirable affect.

• If FM broadcasts are difficult to hear, set DSO to

OFF.

MP3 playable CD Unit

(optional)

This unit can control external MP3 playable CD

units with the CUSTOM FILE functions.

If you connect the optional MP3 playable CD

units, you can play discs containing MP3 files

and use the CUSTOM FILE functions (page 11,

12).

Listening to an MP3 file

1 Press (SOURCE) repeatedly to select

“CD.”

2 Press (MODE) repeatedly until the

appropriate indication for the MP3

playable CD unit (“CD1,” “CD2,” etc.)

appears.

Playback starts.

When the last file on the disc is over

The file number indication returns to “1,” and

playback restarts from the first file of the disc.

Notes

• If a disc with no MP3 files (tracks) is inserted, “CD”

appears in the disc type display to start playback but

there will be no sound.

• Before playing a track, this unit reads all track and

album information on the disc. Depending on the

track structure, it may take more than a minute

before play begins. During this time, “READ” is

displayed. Please wait for play to start automatically

when the reading is complete.

Display items

*1 While displaying an ID3 tag, the album number

does not appear.

*2 If the disc has been labeled by this unit using the

CUSTOM FILE function, Disc Memo is displayed

preferentially.

*3 When pressing (DSPL), “NO NAME” indicates that

there is no disc name, album name, or track title

and “NO ID3” indicates that there is no ID3 tag.

Notes

• Some characters cannot be displayed. Characters

and signs which cannot be displayed appear as “ *.”

• For some ID3 tags with very many characters,

information may not scroll.

• This unit cannot display the artist name for each

track of an album.

Tip

When A.SCRL (Auto Scroll) is set to OFF and the

album/track name is changed, the album/track name

does not scroll.

To Press

Stop playback (OFF)

Eject the disc (OPEN) then Z

Skip tracks

–Automatic

Music Sensor

(SEEK) (./>)

[once for each track]

Fast-forward/

reverse

–Manual Search

(SEEK) (m/M)

[hold to desired point]

Skip discs

–Disc selection

(DISC/PRESET) (+/–)

[once for each disc]

Skip albums

–Album selection

(DISC/PRESET) (+/–)

[hold to desired point]

To Press

Switch display

item

(DSPL)

Scroll display item (SCRL)

Displayable items

• Track number/ Elapsed playing

time

•Disc name*

• Album name*

•Track title*

•ID3 tag*

Displayable items

•Source

•Clock

Displayable items

• Disc number

• Album number*

La page charge ...

Sony CDX-CA705M Manuel utilisateur

Marque: Sony

Modèle: CDX-CA705M

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

CDX-CA720X

Télécharger le PDF

rapport

dans d''autres langues

English: Sony CDX-CA705M User manual

Sony CDX-CA705M Manuel utilisateur

Ce manuel convient également à

Sony CDX-CA705M Manuel utilisateur

dans d''autres langues

Documents connexes