DMP Electronics 1127W PIR Motion Detector Guide d'installation

Marque: DMP Electronics

Modèle: 1127W PIR Motion Detector

Taper: Guide d'installation

Ce manuel convient également à

1127W PIR MOTION DETECTOR

Installation Guide

DESCRIPTION

The 1127W is an 1100 Series Wireless

Wall Mount Wide Angle PIR. The

1127W provides Pet Immunity up to

40 lbs. The Detection area is

36° x 84° angle using a Fresnel

lens. The PIR includes a case

tamper and functionality to allow

sensor conﬁguration from the

panel. Features include R.F.I. and

Noise Immunity, Sensitivity, Pulse

Count, Walk Test, & Disarm Disable

programming.

Compatibility

• All DMP 1100 Series Wireless

Receivers and panels

What is Included?

• One PIR detector with DMP

wireless transmitter

• Two CR123 batteries

• Hardware pack

PROGRAM THE PIR IN THE PANEL

When programming the 1127W in the panel, refer to the panel

programming guide as needed.

Note: When setting up a wireless system, it is recommended

to program zones and connect the receiver before installing

batteries in the transmitters.

1. In ZONE INFORMATION, enter the wireless zone number.

2. Enter the zone name.

3. Select NT (Night) as the ZONE TYPE.

4. Select the AREA.

5. At the NEXT ZN? prompt, select NO.

6. Select YES when WIRELESS? displays.

7. Enter the eight-digit SERIAL# and press CMD.

8. Enter the SUPRVSN TIME and press CMD.

9. Choose whether or not to enable DISARM DISABLE (panel

ﬁrmware Version 172 and higher only). Selecting YES allows

the 1127W to be disabled for Night and Exit type zones while

the area is disarmed.

10. At PULSE COUNT, choose either 2 or 4. The pulse count is

the number of pulse inputs (trips) the 1127W needs to sense

before going into alarm.

11. At SENSITIVITY, choose either LOW or HIGH. Selecting

LOW sensitivity may reduce false alarms for installations in

harsh environments.

12. At the NEXT ZN? prompt, select YES if you are ﬁnished

programming the zone. Select NO if you would like to access

additional programming options.

When a receiver is installed, powered up, or the panel is reset, the

supervision time for transmitters is reset. If the receiver has been

powered down for more than one hour, wireless transmitters may

take up to an additional hour to send a supervision message unless

tripped, tampered, or powered up. This operation extends battery

life for transmitters. A missing message may display on the keypad

until the transmitter sends a supervision message.

INSTALL THE BATTERIES

Observe polarity when installing the batteries. Use only 3V lithium

batteries, DMP Model CR123.

If the batteries reach the factory preset low level, a Low Battery

signal is sent to the panel. The 1127W PIR remains operational

for approximately 30 days to allow adequate time to replace the

batteries.

1. Remove the front cover. See Figure 2.

2. Remove the batteries (if installed) before installing new

batteries.

3. Observe polarity and insert the batteries into the battery

holder.

Caution: Risk of ﬁre, explosion, and burns. Do not recharge,

disassemble, heat above 212°F (100°C), or incinerate.

Properly dispose of used batteries.

Figure 1: 1127W PIR

2 1127W INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

MOUNT THE DETECTOR

Caution: You must be free of static electricity before handling sensor circuit boards. Touch a grounded, bare

metal surface before touching circuit boards or wear a grounding strap.

Locate the Unit:

• On a rigid vibration-free surface

• Where the expected intruder movement is across the

detection pattern

Do Not Locate the Unit:

• On a surface exposed to moisture

• In any area containing excessive metallic surfaces

• Where it may be exposed to false alarm sources such as:

direct sunlight, heat sources (heater, radiators, etc.) in the

ﬁeld of view or strong air drafts (fans, air conditioner, etc.)

LED Survey Operation

The PIR transmitter provides a survey capability to allow one

person to conﬁrm communication with the receiver while the cover

is removed. This allows you to easily determine the best location for

the 1127W.

1. Hold the 1127W in the exact desired location.

2. Press the tamper switch to send data to the receiver and

determine if communication is conﬁrmed or faulty. See

Figure 2 for tamper switch location.

SELECT A LOCATION

Figure 3: Remove the Cover

Cover Lock Screw

Tamper

Corner Mount Holes

Wall Mount Holes

When mounting the detector, refer to Figure 3.

1. Remove the front cover from the

detector.

2. Remove the batteries and the PCB from

the back cover to expose mounting holes.

Use your thumbs to push on the battery

case to slide the PCB toward the top of

the back cover and lift out.

3. Select the appropriate mounting holes

on the back cover for either corner or ﬂat

wall mounting.

4. With the Cover Lock Screw toward the

bottom, attach the back cover to the

wall, up to 8’ high, using screws and wall

anchors, do not over-tighten.

5. Reinstall the PCB in the back cover in the

reverse order of Step 2.

6. Reinstall the batteries and front cover.

Figure 2: Detection Pattern

84˚

Top View

Side View

8.0’ (2.4m)

10’

20’ 30’ 36’

(5m) (10m)(11m)

65˚

32˚

14˚

7˚

Conﬁrmed: If communication is conﬁrmed, the survey LED under the board turns on when data is

sent to the receiver and o when acknowledgement is received. To view this survey LED, turn the

1127W sideways. Repeat this test to conﬁrm ﬁve separate consecutive LED blinks. Any indication

otherwise means proper communication has not been established.

Faulty: If communication is faulty, the LED remains on for about 8 seconds or ﬂashes multiple times

in quick succession. Relocate the 1127W or receiver until the LED conﬁrms clear communication.

1127W INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

TEST THE DETECTOR

Walk Test

1. From the Walk Test menu of the panel, select the PIR Walk Test to place the PIR in walk test mode

(enabling the LED) for 30 minutes. After 30 minutes, the Walk Test automatically exits and the PIR returns

to normal.

Any 1127W PIR Transmitters that have DISARM DISABLE set to YES are temporarily enabled when the Walk

Test is selected. Upon completion of Walk Test, the transmitter is disabled again.

2. After entering the walk test mode, thoroughly test the installation to insure proper protection pattern of the

installed units. The walk test is a local test only and no results are sent to the Central Station.

Transmission Test

1. After programming the unit, close the cover to restore the tamper switch.

2. Verify that the keypad display indicates a signal received from the detector.

ADDITIONAL INFORMATION

Battery Life Expectancy

Typical battery life expectancy for a DMP Model 1127W Wireless PIR is ﬁve years, based on 300 trips per day. Battery life can

be increased 40% to seven years by programming the Disarm Disable feature as YES. DMP wireless equipment uses two-way

communication to extend battery life.

The following situation can extend battery life expectancy:

• Enabling the Disarm Disable feature in Zone Programming allows the PIR to be disabled while the area is disarmed. This

eliminates frequent motion from being detected in a high trac area during the disarmed period.

• Extend transmitter supervision time in panel programming.

The following situations can reduce battery life expectancy:

• If a receiver is unplugged or not installed.

Note: Transmitters continue to send supervision messages until a receiver returns an acknowledgement. After an

hour the transmitter only attempts a supervision message every 60 minutes.

• Programming the Disarm Disable feature as NO where frequent transmissions, in areas of high trac, cause messages

to be sent every time movement is detected.

• When installed in extreme hot or cold environments.

Maintenance

When installed and used properly, the unit provides years of service with minimal maintenance. To ensure proper operation,

perform unit testing annually as described. Clean the cover and optional bracket with a water dampened cloth as needed to

keep it free of dust and dirt. Always test the unit after cleaning.

Mounting Outside

The temperature range for mounting outside is 32 - 120 ° F with a humidity at 85% at 86 ° F.

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-1055 1.03 20235

1127W

Speciﬁcations

Battery

Life Expectancy 5

to 7 years

Type 3 V CR123

Transmit Condition Alarm, Low Battery

Mounting height 8 feet

Frequency Range 905 - 924 MHz

Dimensions

2.7” W x 1.77” D x 4.33” H

6.9 W x 4.5 D x 11.0 H cm

Color White

Ordering Information

1127W-W Wide Angle PIR

CR123 3 V battery

Patents

U.S. Patent No. 7,239,236

Certiﬁcations

FCC Part 15: CCKPC0152

Industry Canada: 5251A-PC0152

Underwriters Laboratory (UL) Listed

ANSI/UL 639 Intrusion Detection Units

ANSI/UL 1023 Household Burglar Alarm

System Units Accessory

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from

all persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada Licence-exempt RSS standards. Operation is subject to the following two

conditions:

1. This device may not cause interference, and

2. this device must accept any interference, including interference that may cause undesired operation of the device.

This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits speciﬁed by Health

Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general

bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites

établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces

(20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand

public.

DMP Electronics 1127W PIR Motion Detector Guide d'installation

Marque: DMP Electronics

Modèle: 1127W PIR Motion Detector

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DMP Electronics 1127W PIR Motion Detector Installation guide

DMP Electronics 1127W PIR Motion Detector Guide d'installation

Ce manuel convient également à

DMP Electronics 1127W PIR Motion Detector Guide d'installation

dans d''autres langues

Documents connexes

Autres documents