Built-In Refrigeration Use & Care Guide
BUILT-IN REFRIGERATION
Customer Care
The model and serial number are printed on the enclosed
product registration card. Both numbers are also listed on
the product rating plate. Refer to page 4 for rating plate
location. For warranty purposes, you will also need the date
of installation and name of your authorized Sub-Zero dealer.
Record this information below for future reference.
If your product ever needs attention, be sure to use a
Sub-Zero factory certied service provider recommended
by our customer care center, or select one from our list of
providers available at subzero.com/locator. All factory certi-
ed service providers are carefully selected and thoroughly
trained by us.
SERVICE INFORMATION
Model Number
Serial Number
Date of Installation
Certied Service Name
Certied Service Number
Authorized Dealer
Dealer Number
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
Contents
4 Built-In Features
5 Electronic Controls
6 Storage
8 Operation
13 Care Recommendations
14 Technical Data
16 Troubleshooting
19 Sub-Zero Warranty
CALIFORNIA PROPOSITION 65
WARNING
This product may contain chemicals known to the state
of California to cause cancer or reproductive harm.
2
|
Sub-Zero Customer Care 800.222.7820
subzero.com
|
3
Thank You
Thank you for your purchase. We look forward to being part of your home for decades to
come. As a third-generation family-owned company, we take a very personal stake in the
preservation of your family’s food. We built our business and our reputation on helping
families serve the freshest food possible.
With your purchase, you receive one of the strongest warranties in the appliance industry.
Take a moment to read the full warranty statement on page 19. It’s also important to
register your Sub-Zero to ensure that you don’t miss out on exclusive owner benets,
such as; assurance that you will be taken care of in the unlikely event that service
becomes necessary during the warranty period, and a proof-of-purchase record in case
of a home insurance claim. You may register by one of the following options:
• Mail in the completed Sub-Zero product registration card.
• Register online at subzero.com/register and create a personalized My Sub-Zero/Wolf
account using the serial number on your product.
• Register by phone by calling Sub-Zero Customer Care at 800-222-7820.
As a Sub-Zero owner, you can count on ongoing support, day in and day out. Our cus-
tomer care center is available 24 hours a day, seven days a week and staffed by knowl-
edgeable product experts at our factory in Madison, Wisconsin. Should the need arise,
simply call 800-222-7820 and speak with one of our product experts. They will help
troubleshoot any issues you might have.
We are condent this guide will answer your questions about the features, operation, and
maintenance of your Sub-Zero, but if you have additional questions, please contact us at
800-222-7820 or visit us online at subzero.com.
4
|
Sub-Zero Customer Care 800.222.7820
Built-In Features
FEATURES
1
Product Rating Plate
2
Electronic Control Panel and Display
3
Freshness Cards
4
Door Shelves
5
Dairy Compartment
6
Refrigerator Storage Drawers
7
High-Humidity Crisper Drawer
8
Glass Shelves
9
Freezer Baskets
10
Ice Container
11
Air Purication System
12
Water Filtration System (behind grille)
13
Automatic Ice Maker
14
Ice | Water Dispenser (dispenser models)
15
Condenser (behind grille)
BUILT-IN FEATURES
Over-and-under model.
1
8
3
9
15
13
7
11
Side-by-side model with internal dispenser.
2
6
12
5
4
10
2
8
3
6
15
9
10
13
1
4
12
5
14
7
11
subzero.com
|
5
ELECTRONIC CONTROLS
Control Panel
FUNCTION
LIGHTS Turns interior accent lighting on or off for glass
door models.
ICE MAKER Turns power to ice maker on or off. Use to disable
ice maker during extended vacations.
MAX ICE Activates or deactivates max ice feature which
increases ice production 30% for a 24-hour period.
COLDER
WARMER
Adjusts tem per ature in one-degree increments.
Combination units have separate temperature con-
trols for refrigerator and freezer. Temper atures are
preset at 38°F
(3°C) and 0°F (-18°C).
PURE AIR Activates or deactivates air purication system.
ALARM Activates or deactivates door alarm. An audible
chime indicates door has been left ajar for more than
60 seconds.
POWER Turns unit on or off. When power is off, ‘OFF’ will
appear in control panel display. Turning power off at
the control panel eliminates the need to unplug or
turn power off at the circuit breaker during service or
extended vacations.
Control panel and display (model BI-30UG shown).
Display
INDICATOR
Illuminates or ashes when electronic control system
has detected a temperature or ice maker problem, or if
condenser needs to be cleaned.
Illuminates when air purication system is activated
and ashes when cartridge needs to be replaced.
After the cartridge has been replaced, touch and hold
PURE AIR on the control panel for 5 seconds to
reset.
Illuminates when water lter needs to be replaced.
Illuminates when ice maker system is activated.
Illuminates when max ice feature is activated.
Illuminates when door alarm is activated.
Illuminates when accent lighting is activated for glass
door models.
6
|
Sub-Zero Customer Care 800.222.7820
Keeping Food At Its Best
This Sub-Zero features a unique dual refrigeration system
to keep food fresher longer.
With the Sub-Zero dual refrigeration system, individual
refrigerator and freezer systems have been designed to
maintain accurate, consistent temperatures and proper
humidity levels for longer food life expectancy. Dual refrig-
eration eliminates transfer of fresh food odors to frozen food
and ice and does not freeze the moisture out of the air in the
fresh food section.
For handy tips and information on how to maximize food
freshness, refer to the freshness cards stored in the
refrigerator.
Refrigerator Storage
DOOR SHELVES
To remove a door shelf or the dairy compartment, lift from
the bottom and slide out. To reinstall, place in the desired
position and slide the shelf down onto the guides. Refer to
the illustration below.
IMPORTANT NOTE: If door opening is limited to 90°, door
shelves may need to be removed before removing a storage
drawer or glass shelf.
STORAGE
STORAGE DRAWERS
To remove a storage drawer, pull forward until the drawer
stops. Lift the front of the drawer slightly, then pull forward.
Refer to the illustration below.
For the French door model, drawer slides may need to be
pushed back manually to provide sufcient clearance for
removal.
To reinstall, push drawer slides in. Align the drawer with
slides and push back until it stops. Press down on the front
of the drawer to engage the slides.
GLASS SHELVES
To remove or adjust a glass shelf, tilt up, then lift up and out.
To reposition, insert shelf in the tracks along the back wall,
then lower the front until it locks into position. Refer to the
illustration below.
IMPORTANT NOTE: Use care when handling glass shelves to
prevent breakage or scratching the interior.
CAUTION
Glass shelves should warm to room temperature before
immersing in warm water.
Storage drawer removal.
Glass shelf removal.
Door shelf removal.
subzero.com
|
7
ICE CONTAINER
BI-36F and over-and-under models | To remove, pull con-
tainer forward until it stops, then lift out.
Side-by-side models | To remove, pull container forward
until it stops, then lift to clear the carrier assembly along the
back. Pull forward and out. Refer to the illustration below.
Dispenser models | To remove, pull container out partially,
then rotate and pull out. Refer to the illustration below.
STORAGE
Freezer Storage
FREEZER BASKETS
BI-36F and side-by-side models | To remove, pull forward
until basket stops. Pull the two metal clips located behind
the bottom two corners of the basket forward, then lift up
and out. Refer to the illustration below. To reinstall, push
drawer slides in. Align the basket with slides and push
back until it stops. Press down on the front of the basket to
engage slides.
IMPORTANT NOTE: To remove for models BI-36S, BI-42S,
BI-42SID and BI-42SD, the basket must be raised
and pulled through the opening in the door liner after
disengaging.
Over-and-under models | To remove the upper and lower
freezer baskets, lift up and out. Refer to the illustration
below. To reinstall, insert the lower basket into the four
corner retainers. Position the upper basket onto the side
rails and slide back until it clicks.
BI-36F and side-by-side models.
Over-and-under models.
Side-by-side models.
Dispenser models.
8
|
Sub-Zero Customer Care 800.222.7820
AIR PURIFICATION CARTRIDGE REPLACEMENT
1 To access the air purication cartridge, grasp the outside
cover from the bottom and rotate upward. Refer to the
illustration below.
2 Grasp the black cover from the top and rotate down-
ward. The cartridge will pop out and can be removed.
3 Remove the new cartridge from packaging and insert
with connector pointing downward.
4 Once in position, close the black cover. Then rotate the
outside cover downward until it closes against the back
wall.
5 Once the cartridge has been replaced, touch and hold
PURE AIR on the control panel for ve seconds to reset.
The
indicator will appear in the control panel display
but not ash.
Air Purication System
The advanced air purication system of Sub-Zero built-in
models reduces bacteria, odors and ethylene gas, which
causes premature ripening in fruits and vegetables. The
air purication cartridge has been factory installed and is
located inside the refrigerator, on the back wall.
To initiate air purication, touch PURE AIR on the control
panel.
The cartridge will last approximately one year. The
indicator will ash in the control panel display when the
cartridge needs to be replaced.
Replacement Sub-Zero air purication cartridges can be
ordered online at subzerowolfstore.com. For questions,
contact Sub-Zero customer care at 800-222-7820.
CAUTION
The air purication system complies with applicable
Federal requirements regarding incidental exposure
to ultraviolet light. Lamp contains mercury. Manage in
accordance with disposal laws. Visit earth911.com or
call 800-222-7820.
OPERATION
Air purication cartridge.
subzero.com
|
9
OPERATION
WATER FILTER REPLACEMENT
1 To access the water lter, pull out on the bottom edge
of the grille assembly and rotate upward.
2 To remove the old lter, rotate counterclockwise one-
quarter turn, then pull out. Refer to the illustration below.
It is normal for a small amount of water to drip when
the lter is removed. It should be wiped up with a paper
towel or cloth.
3 Remove the new lter from packaging and remove
plastic cap.
4 Insert the new lter into the manifold and turn clockwise.
5 Once the new lter has been installed, press and hold
the water lter reset button for ve seconds to reset.
Refer to the illustration below.
Water Filtration System
The water ltration system of Sub-Zero built-in models
supplies ltered water to the ice maker and water dispenser
(dispenser models) to produce great-tasting water and ice.
IMPORTANT NOTE: When using the water ltration system
for the rst time and after lter replacement, it is neces-
sary to clear any air from the system and allow the lter to
assist in cleaning the water lines. For non-dispenser models,
discard the rst two full containers of ice. For dispenser
models, dispense several glasses of water for a period of
two minutes.
If the water ltration system will not be utilized, it can be
placed in water lter bypass mode by removing the lter.
The lter is rated for 750 gallons
(2839 L) or one year, which-
ever comes rst. The
indicator will illuminate in the
control panel display when the lter needs to be replaced.
Replacement Sub-Zero water lters can be ordered online
at subzerowolfstore.com. For questions, contact Sub-Zero
customer care at 800-222-7820.
Water lter removal.
WATER FILTER
Water lter location.
WATER FILTER
RESET BUTTON
WATER
FILTER
10
|
Sub-Zero Customer Care 800.222.7820
OPERATION
Ice | Water Dispenser
The rst time the water dispenser is used, purge the water
system and storage tank for three minutes. This will clear
any air in the system, along with impurities from new
plumbing connections.
Initially, for water to dispense properly, press and hold
WATER or the water dispenser button until water ows from
the dispenser. It may need to be pressed for 60 seconds for
water to ll the internal reservoir tank.
The chilled water reservoir tank holds approximately 40 oz
(1.2 L) of ltered water. It may take several hours to chill the
water to refrigerator temperature during the original ll and
after a large amount of water is dispensed.
CAUTION
Limit continuous ice and water dispenser operation to
seven minutes or less.
Ice Maker Operation
To initiate ice production, touch ICE MAKER on the control
panel. After initial start-up, discard the rst few batches
of ice. The ice may contain impurities from new plumbing
connections.
The ice maker will cycle every two hours. If ice is not used
regularly it may fuse together. To avoid, discard ice and
allow ice maker to replenish.
Sabbath
This appliance is certied by Star-K to meet strict religious
regulations in conjunction with specic instructions found
on www.star-k.org.
To initiate Sabbath mode, while the unit is on, touch POWER
on the control panel. ‘OFF’ appears in the control panel
display. Touch and hold POWER for 10 seconds until ‘SAb’
appears in the display indicating Sabbath mode has been
initiated. Lights, ice maker, door alarm and dispenser (if
applicable) will be disabled. To return to normal operating
conditions, touch POWER.
subzero.com
|
11
Ice | Water Dispenser
INTERNAL DISPENSER
For models BI-42SID and BI-48SID, the internal ice and
water dispenser is designed to accommodate a 16-oz
(.5 L)
pint glass. Larger containers may be used but may compro-
mise the effectiveness of the dispenser. Drops of water may
collect in the removable water grille located directly below
the dispenser. Refer to the illustration below.
FUNCTION
ICE Press and hold to dispense ice.
WATER Press and hold to dispense water.
For models with an internal water only dispenser, the
dispenser is located inside the refrigerator on the left wall.
Press a glass against the dispenser to activate water ow.
Water ow will stop when the glass is pulled away. Refer to
the illustration below.
EXTERNAL DISPENSER
Drops of water may collect in the removable water grille.
This is not a drain. Do not pour water into the water grille.
For large quantities of ice, a bulk ice dispenser is located
inside the refrigerator. Refer to the illustrations below.
FUNCTION
LIGHT Press to cycle through lighting options; lights off,
lights on and control panel lights only.
ICE Press and hold to dispense ice.
WATER Press and hold to dispense water.
LOCK Press and hold for 3 seconds to activate or deac-
tivate the dispenser lock. Lock indicator will be
illuminated when dispenser is locked.
BULK ICE Press and hold to dispense large quantities of ice.
OPERATION
External dispenser.
WATER
GRILLE
Bulk ice dispenser.
BULK ICE
WATER
ICE
WATER
GRILLE
WATER DISPENSER
Internal ice and water
dispenser.
Internal water dispenser.
12
|
Sub-Zero Customer Care 800.222.7820
Interior Lighting
For glass door models, accent lighting can be turned on
and off by touching LIGHTS on the control panel. The
indicator will illuminate when accent lighting is activated.
FREEZER LIGHTING
Over-and-under models | Lighting is located in upper front
section of the freezer compartment. To remove the light
diffuser, gently compress the diffuser to release it from sup-
porting guides.
Side-by-side models | Freezer basket lighting is located
above the ice container. To access the light bulb, remove
the ice container and push the carrier assembly to the back
of the unit. The bulb will be accessible under the xed shelf
in front of the ice maker.
Dispenser models | Lighting above the ice container
is accessible by removing the ice container. Refer to ice
container removal on page 7. Once the container has been
removed, remove the light diffuser as described in overhead
lighting. Lighting below the ice container is accessible by
removing the light diffuser. To remove, press the plastic
lip up and pull the diffuser out of the supporting guides.
Freezer basket lighting is located below the xed shelf on
the back wall of the freezer. To access the light diffuser, rst
remove the freezer basket below the xed shelf. To remove
the light diffuser and access the light bulb, gently compress
the diffuser to release it from supporting guides.
OPERATION
subzero.com
|
13
CARE RECOMMENDATIONS
Cleaning
INTERIOR CLEANING
For over-and-under and side-by-side models, the refrig-
erator or freezer may be disabled without disrupting the
other section. To disable a section, touch POWER. Touch
and hold WARMER for the section being disabled, continue
to hold and touch POWER. Double dashes will appear in the
control panel display. Repeat to turn the section back on.
To clean interior surfaces and all removable parts, wash with
a mild solution of soap, water and baking soda. Rinse and
dry thoroughly. Avoid getting water on lights and control
panel.
CAUTION
Do not use vinegar, rubbing alcohol or other alcohol-
based cleaners on any interior surface.
STAINLESS STEEL EXTERIOR
Use a nonabrasive stainless steel cleaner and apply with a
soft lint-free cloth. To bring out the natural luster, lightly wipe
surface with a water-dampened microber cloth followed by
a dry polishing chamois. Always follow the grain of stainless
steel.
CONDENSER CLEANING
CAUTION
Before cleaning the condenser, turn power off at the
control panel. Wear gloves to avoid injury from sharp
condenser ns.
The condenser is located behind the ip-up grille. To
access, pull out on the bottom edge of the grille and rotate
upward. Use a soft bristle brush and vacuum to remove
dust and lint from the condenser. Clean the condenser every
three to six months. Refer to the illustration below.
IMPORTANT NOTE: To avoid damaging condenser ns,
vacuum in the direction of the ns.
CAUTION
Failure to clean the condenser could result in tempera-
ture loss, mechanical failure or damage.
VACATIONS
For extended vacations, turn power off at the control panel.
Empty the unit and block doors open slightly to let fresh
air in and keep interior dry. Water lter should be replaced
before start up.
Condenser location.
CONDENSER
14
|
Sub-Zero Customer Care 800.222.7820
TECHNICAL DATA
Sub-Zero Water Filtration System Data
REPLACEMENT CARTRIDGE (4204490)
Tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor,
Particulate Class I; and against NSF/ANSI Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, Carbofuran,
1,4-dichlorobenzene, Lindane, Toxaphene, Turbidity, Cysts and Asbestos.
OPERATING SPECIFICATIONS
Capacity: certied for up to 750 gallons (2,838 L); up to twelve months
Pressure Requirement: 35 – 120 psi (2.8 – 8.2 bar)
Temperature: 33 – 100°F (0.6 – 38°C)
Flow Rate: 0.78 gpm (2.9 Lpm)
NSF
Standard
Inuent Challenge
Concentration
Average Inuent
Concentration
Product Water Concentration % Reduction
Max Permissable
Product Water
ConcentrationSubstance Average Max Efuent Average Minimum
Chlorine, Taste & Odor 42 2.0 mg/L ± 10% 1.88 mg/L
0.05 mg/L
0.06 mg/L 97.34% 96.80% ≥ 50%
Particulate 42
At least 10,000
particles/ml
5,700,000/ml 30,583/ml 69,000/ml 99.46% 98.78% ≥ 85%
Lead at pH 6.5 53 0.15 mg/L ± 10% 0.153 mg/L <0.001 mg/L <0.001 mg/L 99.34% 99.34% 0.010 mg/L
Lead at pH 8.5 53 0.15 mg/L ± 10% 0.150 mg/L <0.001 mg/L <0.001 mg/L 99.33% 99.33% 0.010 mg/L
Mercury at pH 6.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0003 mg/L 0.0005 mg/L 95.00% 91.66% 0.002 mg/L
Mercury at pH 8.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0008 mg/L 0.0015 mg/L 86.66% 75.00% 0.002 mg/L
Atrazine 53 0.009 mg/L ± 10% 0.009 mg/L <0.002 mg/L <0.002 mg/L 77.77% 77.77% 0.003 mg/L
Benzene 53 0.015 mg/L ± 10% 0.014 mg/L 0.0006 mg/L 0.0011 mg/L 95.71% 92.14% 0.005 mg/L
Carbofuran 53 0.08 mg/L ± 10% 0.081 mg/L <0.001 mg/L <0.001 mg/L 98.76% 98.76% 0.04 mg/L
1,4-dichlorobenzene 53 0.225 mg/L ± 10% 0.208 mg/L <0.0005 mg/L <0.0005 mg/L 99.75% 99.75% 0.075 mg/L
Lindane 53 0.002 mg/L ± 10% 0.002 mg/L 0.00003 mg/L 0.00007 mg/L 98.50% 96.50% 0.0002 mg/L
Toxaphene 53 0.015 mg/L ± 10% 0.015 mg/L <0.001 mg/L <0.001 mg/L 93.33% 93.33% 0.003 mg/L
Turbidity 53 11 ± 1 NTU 10.7 NTU 0.31 NTU 0.49 NTU 97.10% 95.42% 0.5 NTU
Cysts** 53 Minimum 50,000/L 166,500/L <1/L <1/L >99.99% >99.99% >99.95%
Asbestos 53 10
7
to 10
8
bers/L
†
155 MF/L <1 MF/L <1 MF/L >99.99% >99.99% >99%
**Based on the use of Cryptosporidium Parvum oocysts † Fibers greater than 10 μm in length
• Do not use with water that is microbiologically unsafe or of unknown
water quality without adequate disinfection before or after the
system.
• Systems certied for cyst reduction may be used on disinfected
waters that may contain lterable cysts.
• This system must be installed, operated, maintained and lters
replaced as required in order for the product to perform as adver-
tised.
• Note that while the testing was performed under standard labora-
tory conditions, actual performance may vary. The contaminants
or other substances removed or reduced by this water treatment
system are not necessarily in your water.
SPECIAL NOTES
• Replacement Sub-Zero water lter cartridges can be ordered online
at subzerowolfstore.com. For questions, contact Sub-Zero customer
care at 800-222-7820.
• Change lter cartridge at least every twelve months. High sediment
areas may require more frequent lter cartridge replacement.
• Installation and operation instructions, parts and service availability,
and standard warranty are included with the product when
shipped.
• Replace water lter cartridge when the lter indicator is lit or when
water ow becomes too low. Use replacement water lter cartridge
part number 4204490. Replacement lter pricing information can be
found at subzero.com.
Manufactured for: Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744, 800-222-7820
This system has been tested according to NSF/ANSI 42/53 for reduc-
tion of the substances listed below. The concentration of the indicated
substances in water entering the system was reduced to a concentra-
tion less than or equal to the permissible limit for water leaving the
system, as specied in NSF/ANSI 42/53.
subzero.com
|
15
TECHNICAL DATA
16
|
Sub-Zero Customer Care 800.222.7820
TROUBLESHOOTING
Troubleshooting
SERVICE INDICATOR
Illuminated. Touch POWER to turn unit off. Verify con-
denser area is clean. Touch POWER to turn unit on. If
indicator is still illuminated, call Sub-Zero customer care
at 800-222-7820.
Flashing. Contact Sub-Zero factory certied service.
Flashing with audible chime. Contact Sub-Zero factory
certied service.
Flashing. Replace air purication cartridge. Also, replace
cartridge if there is an odor inside unit.
Flashing. Replace water lter. Also, replace lter if ice
tastes bad, is discolored, ice cubes are small or if water
ow from dispenser is slow.
Flashing with audible chime. Door has been left ajar for
more than 60 seconds. Close door.
UNIT OPERATION
No lights or cooling.
• Verify power is on.
• Verify electrical power to unit and home circuit breaker
is on.
No lights in refrigerator or freezer.
• Door/drawer may have been left ajar which has disabled
lights to eliminate excess heat. If lights are out, close
door/drawer for one hour. If lights are still out, contact
Sub-Zero factory certied service.
• LED interior lighting must be replaced by Sub-Zero
factory certied service.
Frost, condensation or ice build up inside unit.
• Verify condenser is clean.
• Verify door is closing properly.
• Verify door has not been left ajar.
• Verify door gasket does not have rips or tears. If it does,
contact Sub-Zero factory certied service.
• If icing is heavy, turn unit off and use a hair dryer to melt
ice. Hair dryer should be set on low and kept moving
at all times. Once ice has melted, wipe up water with a
cloth or paper towel.
High temperatures, unit runs excessively or unit giving off
too much heat.
• Verify condenser is clean.
• Verify door is closing properly.
• Verify door has not been left ajar.
• Increased ambient temperatures may cause compres-
sors to run longer.
• If temperature display shows 38° and 0°, but is not
cooling, unit may be in showroom mode. Contact
Sub-Zero Customer Care at 800-222-7820.
subzero.com
|
17
Troubleshooting
ICE PRODUCTION
No ice.
• Verify
indicator appears in control panel display.
• Verify ice maker has been on for at least 24 hours.
• Verify freezer temperature near 0°F.
• Verify ice container is properly installed.
• Verify ice maker arm in down position.
• Verify water is being supplied to unit.
• Verify water lter has been replaced within the last 12
months and installed properly.
• Verify water lter has been removed if a reverse osmosis
ltration system is being utilized.
• Verify
indicator is not ashing. If ashing, touch MAX
ICE and ICE MAKER on the control panel simultaneously.
Blue or green ice.
• Possible copper supply line corrosion. Contact plumber
to clean or replace.
Black ecks in cubes.
• Stop use and contact Sub-Zero factory certied service.
Bad taste.
• Defrost freezer and clean with soap and water.
• Place coffee grounds or charcoal briquettes in freezer to
absorb odor.
Hollow cubes.
• Clean condenser. Contact Sub-Zero factory certied
service if unresolved.
TROUBLESHOOTING
ODOR
• Unit should be cleaned before using for the rst time.
This will clear any odors that may have been trapped
during shipping.
• Replace air purication cartridge.
• Clean unit and shelving thoroughly.
• Uncovered food could create odor which may require
cleaning.
• Remove and clean drain pan located behind kickplate,
and reinstall.
18
|
Sub-Zero Customer Care 800.222.7820
TROUBLESHOOTING
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service
marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
Troubleshooting
SERVICE
• Maintain the quality built into your product by contacting
Sub-Zero factory certied service. For the name of the
nearest Sub-Zero factory certied service, check the
contact & support section of our website, subzero.com
or call Sub-Zero customer care at 800-222-7820.
• When contacting service, you will need the model and
serial number of your unit. Both numbers are listed on
the product rating plate. Refer to page 4 for rating plate
location.
• For warranty purposes, you will also need the date
of installation and name of your authorized Sub-Zero
dealer. This information should be recorded on page 2
of this guide.
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defec-
tive in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will
be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless
otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all
connecting tubing. If the owner uses Sub-Zero factory certied service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certi-
ed service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or
replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certied service
or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at [email protected] or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water lters and air purication cartridges are not covered by the product warranty.
2
|
Línea de atención al cliente de Sub-Zero 800.222.7820
UNIDAD DE REFRIGERACIÓN INTEGRADA
Contenido
4 Características integradas
5 Controles electrónicos
6 Almacenamiento
8 Operación
13 Recomendaciones de cuidado
14 Datos técnicos
16 Resolución de problemas
19 Garantía de Sub-Zero
PROPUESTA 65 DE CALIFORNIA
ADVERTENCIA
Este producto puede contener químicos que el estado
de California considera que causan cáncer o daños
reproductivos.
Atención al cliente
El modelo y número de serie están impresos en la tarjeta
de registro del producto adjunta. Los dos números también
aparecen en la placa de datos del producto. Consulte la
página 4 para encontrar la placa de datos. Para nes de la
garantía, usted también necesitará la fecha de instalación y
el nombre de su distribuidor autorizado de Sub-Zero.
Anote esta información abajo para referencia futura.
Si su producto alguna vez necesita servicio, asegúrese de
usar un proveedor de servicios certicado por Sub-Zero
y recomendado por nuestro centro de atención al cliente,
o seleccione uno de nuestra lista de proveedores dis-
ponibles en subzero.com/locator. Todos los proveedores de
servicio certicados de fábrica han sido cuidadosamente
seleccionados y entrenados a fondo por nosotros.
INFORMACIÓN PARA SERVICIO
Número de modelo
Número de serie
Fecha de instalación
Nombre de servicio certicado
Número de servicio certicado
Distribuidor autorizado
Número de distribuidor
Aviso importante
Para garantizar que este producto sea instalado y operado
de la forma más segura y eciente posible, tome nota de los
siguientes tipos de información resaltada en esta guía:
AVISO IMPORTANTE resalta la información que es
especialmente importante.
PRECAUCIÓN indica una situación en la que se pueden
sufrir heridas leves o provocar daños al producto si no se
siguen las instrucciones.
ADVERTENCIA indica peligro de que se produzcan heridas
graves o incluso la muerte si no se siguen las precauciones.
AVISO IMPORTANTE: En toda esta guía, las dimensiones
entre paréntesis son milímetros, a menos que se especique
lo contrario.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
dans d''autres langues
- English: Sub-Zero BI-36U/S/PH-LH User guide
- español: Sub-Zero BI-36U/S/PH-LH Guía del usuario