Snooper DVR-1HD Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Vehicle Drive Recorder
DVR-1
HD
mini
User manual
Benutzerhandbuch
Guide de l’utilisateur
Manuale per l’utente
Gebruikershandleiding
Manual del usuario
Vehicle Drive Recorder
DVR-1
HD
mini
User manual
UK • 2
Warranty Registration
Please visit www.snooperneo.co.uk and click on the Registration’
button to register your unit for warranty.
Contents Page
Key product features 3
About your Snooper DVR-1HD Mini Vehicle Drive Recorder 4
What’s included? 5
Installing your Snooper DVR-1HD Mini 6
Powering your DVR-1HD Mini 8
Charging the internal battery back-up 10
Preparing a new micro SD card for use 11
Using your Snooper DVR-1HD 12
Reviewing video and audio recordings using the Snooper Player 14
Snooper Player explained 16
Changing your Snooper DVR-1HD’s hardware settings 19
Troubleshooting 22
Technical Specifications 23
Service under Warranty 24
Copyright
Copyright @2014 SNOOPER. All rights reserved. Product specifications and features are for reference only and are subject to change
without prior notice.
UK • 3
Key product features
1. Super compact ‘Mini design. Can be discreetly mounted in any
vehicle.
2. 720P High Definition video with super-wide 120 degree viewing
angle.
3. Auto record. Never miss a thing as your DVR-1HD starts recording
automatically.
4. Built-in microphone.
5. Includes 8GB micro SD card and can support up to 32GB micro SD
card (DVR-1HD Mini requires speed class 6 and above)
6. GPS tracking provides accurate evidence of your route, recording
vehicle speed whilst confirming date and exact time of any incidents.
7. Built-in adjustable G-sensor constantly monitors for impacts and
sudden changes in speed or direction that could indicate you have
been involved in an incident.
8. Event and Incident lock down. Any sections of video footage that are
adjudged by the G-sensor to include an ‘Event or ‘Incident will be
locked and saved so they cannot be automatically over written with
other footage.
UK • 4
About your Snooper DVR-1HD Mini Vehicle Drive
Recorder
REC >/M MIC
DC5V~12V / USB interface
Reset
GPS In
Mic
Power.
Illuminates red to indicate the
unit is powered on.
SOS.
Press to instantly save and lock a
video file.
MIC.
Press to turn the built-in
microphone on and off. The MIC
button will illuminate Orange
when set to record audio.
>/M.
Use to enter menu when device
connected to an appropriate
monitor.
REC.
Will flash blue to indicate that
the unit is recording video
footage and to confirm that the
unit is connected to GPS.
SOS
Power
UK • 5
Speaker
Bracket Interface
TOP VIEW
Camera Lens
Micro SD Card Slot
Infrared light
GPS Windscreen bracket
Whats included?
DVR-1HD Mini
GPS windscreen mount
5V USB car charger
12V Hard wire cable
USB data cable
USB to Video out cable
UK • 6
Installing your Snooper DVR-1HD Mini
DVR1HD Mini has been designed
to be mounted in the front
windscreen of your vehicle using
the GPS windscreen bracket
provided. For best results your
DVR should be mounted centrally,
behind or as near to the rear view
mirror as possible, giving it the
best view of the road ahead.
Follow these instructions to install your DVR1HD Mini.
1. Find a convenient location on your vehicles windscreen where you
can mount the GPS windscreen antenna without obscuring the
drivers view or interfering with any of the vehicles controls. You need
to find a position where your DVR has a clear view of the road ahead
(normally behind or as close as possible to the rear view mirror).
User tip: Don’t forget that you need to get power to your DVR so keep
this in mind when choosing your location.
Please note that the GPS windscreen bracket needs to have a clear
view of the sky to obtain a good GPS connection. Do not position
the bracket where the built-in GPS antenna is obscured by metal. The
UK • 7
GPS antenna should operate through tinted glass and the blacked
out areas often seen around and behind the rear view mirror. The
GPS antenna should also operate through most heat reflective
windscreens, but please test before completing the final installation.
2. Clean the area of glass where you intend to mount the GPS
windscreen bracket with a good quality glass cleaner.
3. Remove the backing from the double sided tape on the GPS
windscreen bracket and carefully position it in the desired location on
the windscreen.
User Tip: It will take approximately 24hrs for the adhesive to ‘go off’ and
for the GPS windscreen bracket to become securely mounted.
4. Slide your DVR1HD Mini on to the windscreen bracket and adjust the
bracket as necessary so that the camera lens is pointing down the
road ahead.
User Tip: For best results your DVR1HD should be angled slightly
downwards away from the sky and towards the road ahead.
UK • 8
Powering your DVR-1HD Mini using the car charger
1. Connect the USB plug on the end of the car charger to the USB
DC5V~12V socket on the end of the DVR. Plug the car charger in to a
12V cigarette lighter socket in your vehicle, ensuring that the cable is
not obscuring the drivers view or interfering with any of the drivers
controls.
Caution: use only the car charger supplied with your Snooper DVR-
1HD Mini. Using a different car charger could cause the unit to operate
incorrectly and could damage the unit invalidating the warranty.
Powering your DVR-1HD Mini using the hard wire
lead
You can power your DVR-1HD by wiring it directly to your vehicles 12V
electrical system using the ‘Hard Wire cable supplied as standard with
your unit.
1. Connect the positive side of the cable (marked with a red plus symbol)
to a 12V permanent live. This is a permanent live which has power if
the if ignition if On or Off.
2. Connect the negative side of the lead to a negative ground - any
metal portion of the vehicles frame.
UK • 9
Important: If you are unfamiliar with this procedure, please consult a
professional auto electrician.
User Tip: We recommend that you power the device to a permanent 12V
supply so that the ‘Parking Mode’ operates correctly. If you power your
DVR-1HD from a ‘switched’ 12V supply that powers off when you turn
the vehicles engine off, your DVR will power off shortly after when the
internal battery back-up has run out of power. With a permanent 12V
supply your DVR1 will remain powered on and can continue to monitor
the area around your vehicle whilst you are away from it.
However please note that if you do connect the device to a
permanent feed, and you are planning to leave your vehicle for an
extended period of time we recommend that your DVR-1HD is either
switched off or disconnected from the power source to avoid draining
your vehicle’s battery.
Caution: use only the hard wire cable supplied with your Snooper
DVR-1HD Mini. Using a different hard wire cable could cause the unit
to operate incorrectly and could damage the unit invalidating the
warranty.
UK • 10
Charging the internal battery back-up
Your DVR1HD includes a small built-in rechargeable battery back-up. This
is required if you want to change the factory default settings and need to
connect the device to a separate monitor or Snooper portable navigation
device.
There are two ways to charge the internal battery.
1. Connect your DVR-1HD to your PC using the USB cable provided.
2. Charge using the USB car charger provided.
When charging, a red LED indicator light will illuminate. Once the internal
battery is fully charged the red LED indicator light will automatically
switch off.
Please note that the internal battery has not been designed to run your
DVR-1HD. Your DVR-1HD must be powered by a permanent 5V or 12V
feed to operate correctly.
UK • 11
Preparing a new micro SD card for use
Please note minimum SD card requirement. Minimum 4GB. Maximum
GB. Speed Class 6 and over.
Your DVR-1HD comes with a Micro SD card pre-installed and already
prepared. However if you choose to upgrade or change the SD card you
will need to prepare it for use first.
1. Power off the device and insert the new SD card.
2. Power on the device. The SOS and power button LEDs will illuminate
red and flash.
3. Press the REC button. The SOS and power button LEDs will stay
illuminated but will stop flashing to indicate the preparation
procedure is underway.
4. After approximately 60 seconds the SOS button LED will turn off and
the blue REC button LED will flash to indicate that the SD card has
been successfully prepared and the unit is ready for use.
User tip: We recommend you connect your DVR to a permanent power
source so that the unit does not power off during the preparation
procedure.
UK • 12
Using your Snooper DVR-1HD
Once installed and correctly powered your DVR-1HD has been designed
to operate automatically. As you drive, the device will automatically record
the view in front of your vehicle and will record all audio within range of
the built-in microphone. The GPS antenna will automatically record your
journey and all video, audio and trip information can be reviewed later
using the Snooper Player software included on the SD card included.
The power button LED will illuminate RED to indicate that the unit is
powered on. The REC button will flash BLUE to indicate your DVR is
recording video footage and has a GPS connection. The MIC button will be
illuminated Orange if the built-in microphone is switched on.
User Tip: If you want to power the unit off at any time, simply press
the power button. When you power it back on again, it will operate
automatically as before.
There are several user selectable settings, but for ease of use we have
carefully set-up your DVR-1HD for optimum performance as follows:-
Image size – 1280 x 720.
For maximum image clarity we have set the image resolution to 1280 x
720.
Time Setup – GMT.
UK • 13
Audio record – On.
When powered on the MIC button will be illuminated orange and your
DVR-1HD will automatically record all audio within range of it’s built-in
microphone.
User Tip: Press the MIC button at any time to temporarily mute the built-
in microphone.
G-Sensor sensitivity – Normal.
The unit’s built-in G-Sensor monitors for any unusual movement such as
heavy breaking, hard impact or sharp turning which may indicate that
your vehicle has been involved in an incident. If the G-sensor is activated
the portion of video that includes this event will be locked and saved so
that it cannot be automatically overwritten.
IR Led – On.
The infrared LEDs help improve visibility at night, especially useful for
Parking Mode.
Frequency – 50 hz
GPS Time Zone – GMT: +0 (zero)
User Tip: We think these are the optimum settings for your DVR-1HD, but
if you wish to change them, please refer to the ‘settings’ section later in
this manual.
UK • 14
Reviewing video and audio recordings using the
Snooper Player.
1. Carefully remove the micro SD card from the device and insert it in to
a USB socket on your PC using an appropriate micro SD card reader.
2. A pop-up box should appear on your PC as follows:-
3. Click on ‘Open folder to view files.
4. Double click on the ‘Snooper Player icon as seen below.
UK • 15
5. The Snooper Player software will be displayed on your computer
screen as follows:-
User Tip: if the following pop-
up box appears, click ‘Continue
without scanning. Any ‘broken
files on the SD card can be
repaired using the Snooper Player
software. Clicking ‘Scan and
fix (recommended) may result
in files being deleted and data
permanently lost.
UK • 16
Snooper Player explained
21
24
25
26
27
1
16
2
17
3
18
4 5 6 7 8 9 10 11 12 13 14 15
19 20
22
23
UK • 17
1. Open folder from your PC containing existing video/audio footage.
2. Click to take a snap shot from any section of video recorded.
3. Save route data. Select a folder to export it from the Snooper Player
and save it to your PC.
4. Delete routes recorded and no longer required, from the Snooper
Player.
5. Change settings such as Language and set up a password to protect
your data.
6. View video footage in slow motion
7. Stop video footage playing.
8. Play/pause video footage.
9. Increase speed of video footage.
10. Adjust volume of audio.
11. Run video footage on repeat.
12. Flip video footage 180 degrees
13. Export GPS coordinates to your PC in KML format.
14. Open and close Google Map view window.
15. Open and close G-sensor information window.
UK • 18
16. Repair broken video files.
17. Unlock ‘Incident/Event video footage.
18. Adjust Brightness, Contrast and Saturation of any video file selected.
19. GPS coordinates.
20. Your speed reading. Click to switch between mph and km/h.
21. Video footage.
22. Compass heading.
23. Adjust size of Snooper Player window.
24. Google Map view. Shows route track using coordinates collected and
saved by DVR-1HD GPS antenna.
25. G-sensor information window. Displays any event information such
as hard breaking, impacts or sharp turns that might indicate that an
incident has occurred on a recorded route.
26. Main route folders.
27. Sub route files.
UK • 19
Changing your Snooper DVR-1HD’s hardware settings
The settings in your DVR-1HD have been set for optimum use but are
user selectable and can be changed by connecting the device to an
appropriate monitor using the video cable provided. You can also connect
the unit to any Snooper PND but may need to purchase an adaptor cable
separately from www.snooper.co.uk
1. Ensure that the DVR-1HD internal battery is fully charged and the SD
card is inserted.
2. Connect the USB to Video cable provided, between your DVR1HD and
a suitable monitor.
3. Power on the DVR1HD. You should see what the DVR1HD camera is
looking at on the monitor.
4. Press the >|M button to enter the Menu.
5. Scroll up and down through the menu using the MIC and SOS button
and use to the REC button to Enter or Confirm a setting.
6. To exit the menu or go back press the >|M button.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145

Snooper DVR-1HD Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à