Snooper DVR-1HD Manuel utilisateur

Vehicle Drive Recorder

DVR-1

HD

mini

User manual

Benutzerhandbuch

Guide de l’utilisateur

Manuale per l’utente

Gebruikershandleiding

Manual del usuario

Vehicle Drive Recorder

DVR-1

HD

mini

User manual

UK • 2

Warranty Registration

Please visit www.snooperneo.co.uk and click on the ‘Registration’

button to register your unit for warranty.

Contents Page

Key product features 3

About your Snooper DVR-1HD Mini Vehicle Drive Recorder 4

What’s included? 5

Installing your Snooper DVR-1HD Mini 6

Powering your DVR-1HD Mini 8

Charging the internal battery back-up 10

Preparing a new micro SD card for use 11

Using your Snooper DVR-1HD 12

Reviewing video and audio recordings using the Snooper Player 14

Snooper Player explained 16

Changing your Snooper DVR-1HD’s hardware settings 19

Troubleshooting 22

Technical Speciﬁcations 23

Service under Warranty 24

Copyright

without prior notice.

UK • 3

Key product features

1. Super compact ‘Mini’ design. Can be discreetly mounted in any

vehicle.

2. 720P High Deﬁnition video with super-wide 120 degree viewing

angle.

3. Auto record. Never miss a thing as your DVR-1HD starts recording

automatically.

4. Built-in microphone.

5. Includes 8GB micro SD card and can support up to 32GB micro SD

card (DVR-1HD Mini requires speed class 6 and above)

6. GPS tracking provides accurate evidence of your route, recording

vehicle speed whilst conﬁrming date and exact time of any incidents.

7. Built-in adjustable G-sensor constantly monitors for impacts and

sudden changes in speed or direction that could indicate you have

been involved in an incident.

8. Event and Incident lock down. Any sections of video footage that are

adjudged by the G-sensor to include an ‘Event’ or ‘Incident’ will be

locked and saved so they cannot be automatically over written with

other footage.

UK • 4

About your Snooper DVR-1HD Mini Vehicle Drive

Recorder

REC >/M MIC

DC5V~12V / USB interface

Reset

GPS In

Mic

Power.

Illuminates red to indicate the

unit is powered on.

SOS.

Press to instantly save and lock a

video ﬁle.

MIC.

Press to turn the built-in

microphone on and oﬀ. The MIC

button will illuminate Orange

when set to record audio.

>/M.

Use to enter menu when device

connected to an appropriate

monitor.

REC.

Will ﬂash blue to indicate that

the unit is recording video

footage and to conﬁrm that the

unit is connected to GPS.

SOS

Power

UK • 5

Speaker

Bracket Interface

TOP VIEW

Camera Lens

Micro SD Card Slot

Infrared light

GPS Windscreen bracket

What’s included?

DVR-1HD Mini

GPS windscreen mount

5V USB car charger

12V Hard wire cable

USB data cable

USB to Video out cable

UK • 6

Installing your Snooper DVR-1HD Mini

DVR1HD Mini has been designed

to be mounted in the front

windscreen of your vehicle using

the GPS windscreen bracket

provided. For best results your

DVR should be mounted centrally,

behind or as near to the rear view

mirror as possible, giving it the

best view of the road ahead.

Follow these instructions to install your DVR1HD Mini.

1. Find a convenient location on your vehicle’s windscreen where you

can mount the GPS windscreen antenna without obscuring the

driver’s view or interfering with any of the vehicle’s controls. You need

to ﬁnd a position where your DVR has a clear view of the road ahead

(normally behind or as close as possible to the rear view mirror).

User tip: Don’t forget that you need to get power to your DVR so keep

this in mind when choosing your location.

Please note that the GPS windscreen bracket needs to have a clear

view of the sky to obtain a good GPS connection. Do not position

the bracket where the built-in GPS antenna is obscured by metal. The

UK • 7

GPS antenna should operate through tinted glass and the blacked

out areas often seen around and behind the rear view mirror. The

GPS antenna should also operate through most heat reﬂective

windscreens, but please test before completing the ﬁnal installation.

2. Clean the area of glass where you intend to mount the GPS

windscreen bracket with a good quality glass cleaner.

3. Remove the backing from the double sided tape on the GPS

windscreen bracket and carefully position it in the desired location on

the windscreen.

User Tip: It will take approximately 24hrs for the adhesive to ‘go oﬀ’ and

for the GPS windscreen bracket to become securely mounted.

4. Slide your DVR1HD Mini on to the windscreen bracket and adjust the

bracket as necessary so that the camera lens is pointing down the

road ahead.

User Tip: For best results your DVR1HD should be angled slightly

downwards away from the sky and towards the road ahead.

UK • 8

Powering your DVR-1HD Mini using the car charger

1. Connect the USB plug on the end of the car charger to the USB

DC5V~12V socket on the end of the DVR. Plug the car charger in to a

12V cigarette lighter socket in your vehicle, ensuring that the cable is

not obscuring the driver’s view or interfering with any of the driver’s

controls.

Caution: use only the car charger supplied with your Snooper DVR-

1HD Mini. Using a diﬀerent car charger could cause the unit to operate

incorrectly and could damage the unit invalidating the warranty.

Powering your DVR-1HD Mini using the ‘hard wire’

lead

You can power your DVR-1HD by wiring it directly to your vehicles 12V

electrical system using the ‘Hard Wire’ cable supplied as standard with

your unit.

1. Connect the positive side of the cable (marked with a red plus symbol)

to a 12V permanent live. This is a permanent live which has power if

the if ignition if On or Oﬀ.

2. Connect the negative side of the lead to a negative ground - any

metal portion of the vehicles frame.

UK • 9

Important: If you are unfamiliar with this procedure, please consult a

professional auto electrician.

User Tip: We recommend that you power the device to a permanent 12V

supply so that the ‘Parking Mode’ operates correctly. If you power your

DVR-1HD from a ‘switched’ 12V supply that powers oﬀ when you turn

the vehicle’s engine oﬀ, your DVR will power oﬀ shortly after when the

internal battery back-up has run out of power. With a permanent 12V

supply your DVR1 will remain powered on and can continue to monitor

the area around your vehicle whilst you are away from it.

However please note that if you do connect the device to a

permanent feed, and you are planning to leave your vehicle for an

extended period of time we recommend that your DVR-1HD is either

switched oﬀ or disconnected from the power source to avoid draining

your vehicle’s battery.

Caution: use only the hard wire cable supplied with your Snooper

DVR-1HD Mini. Using a diﬀerent hard wire cable could cause the unit

to operate incorrectly and could damage the unit invalidating the

warranty.

UK • 10

Charging the internal battery back-up

Your DVR1HD includes a small built-in rechargeable battery back-up. This

is required if you want to change the factory default settings and need to

connect the device to a separate monitor or Snooper portable navigation

device.

There are two ways to charge the internal battery.

1. Connect your DVR-1HD to your PC using the USB cable provided.

2. Charge using the USB car charger provided.

When charging, a red LED indicator light will illuminate. Once the internal

battery is fully charged the red LED indicator light will automatically

switch oﬀ.

Please note that the internal battery has not been designed to run your

DVR-1HD. Your DVR-1HD must be powered by a permanent 5V or 12V

feed to operate correctly.

UK • 11

Preparing a new micro SD card for use

Please note minimum SD card requirement. Minimum 4GB. Maximum

GB. Speed Class 6 and over.

Your DVR-1HD comes with a Micro SD card pre-installed and already

prepared. However if you choose to upgrade or change the SD card you

will need to prepare it for use ﬁrst.

1. Power oﬀ the device and insert the new SD card.

2. Power on the device. The SOS and power button LEDs will illuminate

red and ﬂash.

3. Press the REC button. The SOS and power button LEDs will stay

illuminated but will stop ﬂashing to indicate the preparation

procedure is underway.

4. After approximately 60 seconds the SOS button LED will turn oﬀ and

the blue REC button LED will ﬂash to indicate that the SD card has

been successfully prepared and the unit is ready for use.

User tip: We recommend you connect your DVR to a permanent power

source so that the unit does not power oﬀ during the preparation

procedure.

UK • 12

Using your Snooper DVR-1HD

Once installed and correctly powered your DVR-1HD has been designed

to operate automatically. As you drive, the device will automatically record

the view in front of your vehicle and will record all audio within range of

the built-in microphone. The GPS antenna will automatically record your

journey and all video, audio and trip information can be reviewed later

using the Snooper Player software included on the SD card included.

The power button LED will illuminate RED to indicate that the unit is

powered on. The REC button will ﬂash BLUE to indicate your DVR is

recording video footage and has a GPS connection. The MIC button will be

illuminated Orange if the built-in microphone is switched on.

User Tip: If you want to power the unit oﬀ at any time, simply press

the power button. When you power it back on again, it will operate

automatically as before.

There are several user selectable settings, but for ease of use we have

carefully set-up your DVR-1HD for optimum performance as follows:-

Image size – 1280 x 720.

For maximum image clarity we have set the image resolution to 1280 x

720.

Time Setup – GMT.

UK • 13

Audio record – On.

When powered on the MIC button will be illuminated orange and your

DVR-1HD will automatically record all audio within range of it’s built-in

microphone.

User Tip: Press the MIC button at any time to temporarily mute the built-

in microphone.

G-Sensor sensitivity – Normal.

The unit’s built-in G-Sensor monitors for any unusual movement such as

heavy breaking, hard impact or sharp turning which may indicate that

your vehicle has been involved in an incident. If the G-sensor is activated

the portion of video that includes this event will be locked and saved so

that it cannot be automatically overwritten.

IR Led – On.

The infrared LEDs help improve visibility at night, especially useful for

Parking Mode.

Frequency – 50 hz

GPS Time Zone – GMT: +0 (zero)

User Tip: We think these are the optimum settings for your DVR-1HD, but

if you wish to change them, please refer to the ‘settings’ section later in

this manual.

UK • 14

Reviewing video and audio recordings using the

Snooper Player.

1. Carefully remove the micro SD card from the device and insert it in to

a USB socket on your PC using an appropriate micro SD card reader.

2. A pop-up box should appear on your PC as follows:-

3. Click on ‘Open folder to view ﬁles.

4. Double click on the ‘Snooper Player’ icon as seen below.

UK • 15

5. The Snooper Player software will be displayed on your computer

screen as follows:-

User Tip: if the following pop-

up box appears, click ‘Continue

without scanning’. Any ‘broken’

ﬁles on the SD card can be

repaired using the Snooper Player

software. Clicking ‘Scan and

ﬁx (recommended) may result

in ﬁles being deleted and data

permanently lost.

UK • 16

Snooper Player explained

21

24

25

26

27

1

16

2

17

3

18

4 5 6 7 8 9 10 11 12 13 14 15

19 20

22

23

UK • 17

1. Open folder from your PC containing existing video/audio footage.

2. Click to take a snap shot from any section of video recorded.

3. Save route data. Select a folder to export it from the Snooper Player

and save it to your PC.

4. Delete routes recorded and no longer required, from the Snooper

Player.

5. Change settings such as Language and set up a password to protect

your data.

6. View video footage in ‘slow motion’

7. Stop video footage playing.

8. Play/pause video footage.

9. Increase speed of video footage.

10. Adjust volume of audio.

11. Run video footage on repeat.

12. Flip video footage 180 degrees

13. Export GPS coordinates to your PC in KML format.

14. Open and close Google Map view window.

15. Open and close G-sensor information window.

UK • 18

16. Repair broken video ﬁles.

17. Unlock ‘Incident/Event’ video footage.

18. Adjust Brightness, Contrast and Saturation of any video ﬁle selected.

19. GPS coordinates.

20. Your speed reading. Click to switch between mph and km/h.

21. Video footage.

22. Compass heading.

23. Adjust size of Snooper Player window.

24. Google Map view. Shows route track using coordinates collected and

saved by DVR-1HD GPS antenna.

25. G-sensor information window. Displays any event information such

as hard breaking, impacts or sharp turns that might indicate that an

incident has occurred on a recorded route.

26. Main route folders.

27. Sub route ﬁles.

UK • 19

Changing your Snooper DVR-1HD’s hardware settings

The settings in your DVR-1HD have been set for optimum use but are

user selectable and can be changed by connecting the device to an

appropriate monitor using the video cable provided. You can also connect

the unit to any Snooper PND but may need to purchase an adaptor cable

separately from www.snooper.co.uk

1. Ensure that the DVR-1HD internal battery is fully charged and the SD

card is inserted.

2. Connect the USB to Video cable provided, between your DVR1HD and

a suitable monitor.

3. Power on the DVR1HD. You should see what the DVR1HD camera is

looking at on the monitor.

4. Press the >|M button to enter the Menu.

5. Scroll up and down through the menu using the MIC and SOS button

and use to the REC button to Enter or Conﬁrm a setting.

6. To exit the menu or ‘go back’ press the >|M button.

La page charge ...

Snooper DVR-1HD Manuel utilisateur

Ce manuel convient également à

Snooper DVR-1HD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents