Acson A5WMY15KR Mode d'emploi

MODELS

M5WMY10KR

M5WMY15KR

EnglishDeutschFrançaisEspañolItaliano

MODELS

A5WMY10KR

A5WMY15KR

00_CV_3P257186-2A.fm Page 1 Saturday, October 31, 2009 2:17 PM

1

English

CONTENTS

READ BEFORE OPERATION

Safety Precautions ......................................... 2

Names of Parts .............................................. 4

Preparation before Operation......................... 7

OPERATION

AUTO · DRY · COOL · HEAT · FAN

Operation ....................................................... 9

Adjusting the Airflow Direction ..................... 11

COMFORT AIRFLOW Operation................. 13

POWERFUL Operation ................................ 14

ECONO Operation ....................................... 15

OFF TIMER Operation ................................. 16

ON TIMER Operation................................... 17

CARE

Care and Cleaning ....................................... 18

TROUBLESHOOTING

Troubleshooting ........................................... 22

01_EN_3P257186-2A.fm Page 1 Saturday, October 31, 2009 2:19 PM

2

READ BEFORE OPERATION

Safety Precautions

• Keep this manual where the operator can easily find them.

• Read the precautions in this manual carefully before operating the unit.

• The precautions described herein are classified as WARNING and CAUTION. They both contain

important information regarding safety. Be sure to observe all precautions without fail.

• After reading, keep this manual in a convenient place so that you can refer to it whenever necessary.

If the equipment is transferred to a new user, be sure also to hand over the manual.

WARNING

• In order to avoid fire, explosion or injury, do not operate the unit when harmful, among which

flammable or corrosive gases, are detected near the unit.

• Be aware that prolonged, direct exposure to cool or warm air from the air conditioner, or to air

that is too cool or too warm can be harmful to your physical condition and health.

•

Do not place objects, including rods, your fingers, etc., in the air inlet or outlet. Product malfunctioning,

product or injury damage may result due to contact with the air conditioner’s high-speed fan blades.

• Do not attempt to repair, dismantle reinstall or modify the air conditioner yourself as this may result in

water leakage, electric shocks or fire hazards.

• Do not use flammable spray near the air conditioner, or otherwise fire may result.

•

Beware of fire in case of refrigerant leakage. If the air conditioner is not operating correctly, i.e. not generating

cool or warm air, refrigerant leakage could be the cause. Consult your dealer for assistance. The refrigerant

within the air conditioner is safe and normally does not leak.

However, in the event of a leakage, contact with a naked burner, heater or cooker may result in generation of noxious

gas. Do not longer use the air conditioner until a qualified service person confirms that the leakage has been repaired.

•

Do not attempt to install or repair the air conditioner yourself. Improper workmanship may result in water leakage, electric

shocks or fire hazards. Please contact your local dealer or qualified personnel for installation and maintenance work.

•

When the air conditioner is malfunctioning (giving off a burning odour, etc.) turn off power to the unit and contact your

local dealer. Continued operation under such circumstances may result in a failure, electric shocks or fire hazards.

•

Be sure to install an earth leakage breaker. Failure to install an earth leakage breaker may result in electric shocks or fire.

• Be sure to earth the unit. Do not earth the unit to a utility pipe, lightning conductor or

telephone earth lead. Imperfect earthing may result in electric shocks.

CAUTION

•

Do not use the air conditioner for purposes other than those for which it is intended. Do not use

the air conditioner for cooling precision instruments, food, plants, animals or works of art as

this may adversely affect the performance, quality and/or longevity of the object concerned.

• Do not expose plants or animals directly to airflow from the unit as this may cause adverse effects.

• Do not place appliances that produce naked flames in places exposed to the airflow from the unit as

this may impair combustion of the burner.

WARNING

Failure to follow these instructions properly may

result in personal injury or loss of life.

CAUTION

Failure to observe these instructions properly may

result in property damage or personal injury, which

may be serious depending on the circumstances.

Never attempt. Be sure to follow the instructions.

Be sure to establish an earth connection.

Never wet the air conditioner nor the remote

controller with water.

Never touch the air conditioner nor the

remote controller with wet hands.

01_EN_3P257186-2A.fm Page 2 Saturday, October 31, 2009 2:19 PM

3

English

• Do not block air inlets nor outlets. Impaired airflow may result in insufficient performance or trouble.

• Do not sit or place objects on the outdoor unit. Falling yourself or falling objects could cause injury.

• Do not place objects that are susceptible to moisture directly beneath the indoor or outdoor units.

Under certain conditions, condensation on the main unit or refrigerant pipes, air filter dirt or drain

blockage may cause dripping, resulting in fouling or failure of the object concerned.

• After prolonged use, check the unit stand and its mounts for damage. If left in a damaged condition,

the unit may fall and cause injury.

• To avoid injury, do not touch the air inlet or aluminium fins of the unit.

• The appliance is not intended for use by unattended young children or infirm persons. Impairment of

bodily functions and harm to health may result.

• To avoid oxygen depletion, ensure that the room is adequately ventilated if equipment such as

a burner is used together with the air conditioner.

• Before cleaning, be sure to stop unit operation, turn the breaker off or remove the power cord.

Otherwise, an electric shock and injury may result.

• Only connect the air conditioner to the specified power supply circuit. Power supplies other than the

one specified may result in electric shocks, overheating and fires.

•

Arrange the drain hose to ensure smooth drainage. Imperfect drainage may cause wetting of the building, furniture etc.

•

Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris

accumulate around the unit. Leaves are a hotbed for small animals which can enter the unit. Once in

the unit, such animals can cause malfunctions, smoke or fire when making contact with electrical parts.

• Do not place objects around the indoor unit.

Doing so may have an adverse influence on the performance, product quality, and life of the air conditioner.

• This appliance is not intended to be used by persons with reduced physical, sensory or mental

capabilities, or with lack of operation knowledge, unless they have been given supervision or

instruction concerning the appliance use by person responsible for their safety.

Keep out of children’s reach to ensure that they do not play with the appliance.

• To avoid electric shocks, do not operate with wet hands.

• Do not wash the air conditioner with water, as this may result in electric shocks or fire.

• Do not place water containers (flower etc.) above the unit, as this may result in electric

shocks or fire hazards.

■ To install the air conditioner in the following types of environments, consult the dealer.

• Places with an oily ambient or where steam or soot occurs.

• Salty environment such as coastal areas.

• Places where sulfide gas occurs such as hot springs.

• Places where snow may block the outdoor unit.

• The drain from the outdoor unit must be discharged to a place of good drainage.

■ For installation, choose a place as described below.

•

A place solid enough to bear the weight of the unit which does not amplify the operation noise or vibration.

•

A place from where the air discharged from the outdoor unit or the operation noise will not annoy your neighbours.

• For power supply, be sure to use a separate power circuit dedicated to the air conditioner.

• Relocating the air conditioner requires specialized knowledge and skills. Please consult the dealer

if relocation is necessary for moving or remodeling.

Installation site.

Consider nuisance to your neighbours from noises.

Electrical work.

System relocation.

01_EN_3P257186-2A.fm Page 3 Saturday, October 31, 2009 2:19 PM

4

Names of Parts

■

Indoor Unit

ON/OFF

1

7

2

910 8

34

5

6

11

15

13

12

14

01_EN_3P257186-2A.fm Page 4 Saturday, October 31, 2009 2:19 PM

5

English

■

Outdoor Unit

■ Indoor Unit

1. Air filter

2. Titanium apatite photocatalytic

air-purifying filter:

• These filters are attached to the inside of

the air filters.

3. Air inlet

4. Front panel

5. Panel tab

6. Room temperature sensor:

• It senses the air temperature around the

unit.

7. Display

8. Air outlet

9. Flap (horizontal blade): (page 11.)

10. Louvers (vertical blades):

• The louvers are inside of the air outlet.

(page 12.)

11. Model name plate

12. Indoor unit ON/OFF switch:

• Press this switch once to start operation.

Press once again to stop it.

• The operation mode refers to the following

table.

• This switch is useful when the remote

controller is missing.

13. OPERATION lamp (green)

14. TIMER lamp (yellow): (page 16.)

15. Signal receiver:

•

It receives signals from the remote controller.

• When the unit receives a signal, you will

hear a beep sound.

• Operation start .......... beep-beep

• Settings changed....... beep

• Operation stop........... long beep

■ Outdoor Unit

16. Air inlet (back and side)

17. Refrigerant piping and inter-unit wiring

18. Drain hose

19. Earth terminal:

• It is inside of this cover.

20. Air outlet

21. Outdoor temperature sensor (back)

22. Model name plate

• Appearance of the outdoor unit may differ from some models.

16

20

17

19

18

22

21

Mode

Temperature

setting

Airflow rate

AUTO 25°C AUTO

01_EN_3P257186-2A.fm Page 5 Saturday, October 31, 2009 2:19 PM

6

Names of Parts

■

Remote Controller

1. Signal transmitter:

• It sends signals to the indoor unit.

2. Display (LCD):

• It displays the current settings.

(In this illustration, each section is shown

with its displays on for the purpose of

explanation.)

3. ECONO button:

ECONO operation (page 15.)

4. POWERFUL button:

POWERFUL operation (page 14.)

5. TEMPERATURE adjustment button:

• It changes the temperature setting.

6. ON/OFF button:

• Press this button once to start operation.

Press once again to stop it.

7. MODE selector button:

• It selects the operation mode.

(AUTO/DRY/COOL/HEAT/FAN) (page 9.)

8. FAN setting button:

• It selects the airflow rate setting.

9. SWING button:

• Adjusting the airflow direction. (page 11.)

10. COMFORT AIRFLOW button:

COMFORT AIRFLOW operation (page 13.)

11. ON TIMER button: (page 17.)

12. OFF TIMER button: (page 16.)

13. TIMER CANCEL button:

• It cancels the timer setting.

1

6

2

10

9

8

5

13

4

3

7

12

11

<

iAPJ2

>

01_EN_3P257186-2A.fm Page 6 Saturday, October 31, 2009 2:19 PM

7

English

Preparation before Operation

■

To set the batteries

1. Push down the hook and open

the back cover.

2. Set two dry batteries AAA.LR03

(alkaline).

3. Return the back cover to the

previous position.

■

To operate the remote

controller

• To use the remote controller, aim the transmitter at the indoor unit.

If there is anything to block signals between the unit and the

remote controller, such as a curtain, the unit will not operate.

• Do not drop the remote controller. Do not get it wet.

• The maximum distance for communication is approx. 7m.

■

To fix the remote controller holder

on the wall

1.

Choose a place from where the signals reach the unit.

2. Fix the holder to a wall, a pillar, or similar

location with the screws procured locally.

3. Hang the remote controller on the remote

controller holder.

NOTE

■ Notes on batteries

•

When replacing the batteries, use batteries of the same type, and replace both old batteries together.

• When the system is not used for a long time, take the batteries out.

• The batteries will last for approx. 1 year. If the remote controller display begins to fade and

the degradation of reception performance occurs within a year, however, replace both

batteries with new, size AAA.LR03 (alkaline).

• The attached batteries are provided for the initial use of the system.

The usable period of the batteries may be short depending on the manufactured date of the air conditioner.

■ Notes on remote controller

• Never expose the remote controller to direct sunlight.

•

Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.

• Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such

as inverter-type lamps) is in the room. Consult the shop if that is the case.

• If the remote controller signals happen to operate another appliance, move that appliance

to somewhere else, or consult the shop.

2

3

1

Position

and

correctly!

–

+

Receiver

Remote

controller holder

Remote controller

Screws

01_EN_3P257186-2A.fm Page 7 Saturday, October 31, 2009 2:19 PM

8

Preparation before Operation

■

Turn the breaker on

• Turning on the breaker opens the flap, then closes it again. (This is a normal procedure.)

NOTE

■ Tips for saving energy

• Be careful not to cool (heat) the room too much.

Keeping the temperature setting at a moderate

level helps save energy.

• Cover windows with a blind or a curtain.

Blocking sunlight and air from outdoors

increases the cooling (heating) effect.

• Clogged air filters cause inefficient operation and waste energy. Clean them once in about

every 2 weeks.

■ Please note

•

The air conditioner always consumes 15-35W of electricity even while it is not operating.

The outdoor unit consumes 1-10W to have its electric components work even while it is not

operating.

During standby electricity saving mode : about 1W

The outdoor unit consumes about 35W of power at the time of compressor preheating.

• If you are not going to use the air conditioner for a long period, for example in spring or

autumn, turn the breaker off.

• Use the air conditioner in the following conditions.

• Operation outside this humidity or temperature range may cause a safety device to disable

the system.

Recommended temperature setting

For cooling: 26-28°C

For heating: 20-24°C

Mode Operating conditions If operation is continued out of this range

COOL Outdoor temperature: 10-46°C

Indoor temperature: 18-32°C

Indoor humidity: 80% max.

•A safety device may work to stop the operation.

•Condensation may occur on the indoor unit and drip.

HEAT Outdoor temperature: –15-24°C

Indoor temperature: 10-30°C

•A safety device may work to stop the operation.

DRY Outdoor temperature: 10-46°C

Indoor temperature: 18-32°C

Indoor humidity: 80% max.

•A safety device may work to stop the operation.

•Condensation may occur on the indoor unit and drip.

01_EN_3P257186-2A.fm Page 8 Saturday, October 31, 2009 2:19 PM

9

English

OPERATION

AUTO · DRY · COOL · HEAT · FAN Operation

The air conditioner operates with the operation mode of your

choice.

From the next time on, the air conditioner will operate with the same

operation mode.

■

To start operation

1. Press and select a operation mode.

• Each pressing of the button advances the mode setting in

sequence.

2. Press .

• “ ” is displayed on the LCD.

• The OPERATION lamp lights up.

■

To stop operation

3. Press again.

• “ ” disappears from the LCD.

• Then OPERATION lamp goes off.

■

To change the temperature setting

4. Press .

: AUTO : HEAT

: DRY : FAN

: COOL

AUTO or COOL or HEAT operation DRY or FAN operation

Press to raise the temperature and

press to lower the temperature.

The temperature setting is not variable.

Set to the temperature you like.

01_EN_3P257186-2A.fm Page 9 Saturday, October 31, 2009 2:19 PM

10

AUTO · DRY · COOL · HEAT · FAN Operation

■

To change the airflow rate setting

5. Press .

• Indoor unit quiet operation

When the airflow is set to “ ”, the noise from the indoor unit will become quieter.

Use this when making the noise quieter.

NOTE

AUTO or COOL or HEAT or FAN operation DRY operation

5 levels of airflow rate setting

from “ ” to “ ” plus “ ”

“ ” are available.

The airflow rate setting is not variable.

■ Notes on HEAT operation

• Since this air conditioner heats the room by taking heat from outdoor air to indoors, the

heating capacity becomes smaller in lower outdoor temperatures. If the heating effect is

insufficient, it is recommended to use another heating appliance in combination with the air

conditioner.

• The heat pump system heats the room by circulating hot air around all parts of the room.

After the start of HEAT operation, it takes some time before the room gets warmer.

• In HEAT operation, frost may occur on the outdoor unit and lower the heating capacity. In

that case, the system switches into defrosting operation to take away the frost.

• During defrosting operation, hot air does not flow out of indoor unit.

• A pinging sound may be heard during defrosting operation, which, however does not mean

that the air conditioner has failures.

■ Note on COOL operation

• This air conditioner cools the room by blowing the hot air in the room outside, so if the

outside temperature is high, the performance of the air conditioner drops.

■ Note on DRY operation

• The computer chip works to rid the room of humidity while maintaining the temperature as

much as possible. It automatically controls temperature and airflow rate, so manual

adjustment of these functions is unavailable.

■ Notes on AUTO operation

• In AUTO operation, the system selects a temperature setting and an appropriate operation

mode (COOL or HEAT) based on the room temperature at the start of the operation.

• The system automatically reselects setting at a regular interval to bring the room

temperature to user-setting level.

■ Note on FAN operation

• This mode is valid for fan only.

■ Note on airflow rate setting

• At smaller airflow rates, the cooling (heating) effect is also smaller.

01_EN_3P257186-2A.fm Page 10 Saturday, October 31, 2009 2:19 PM

11

English

Adjusting the Airflow Direction

You can adjust the airflow direction to increase your comfort.

■

To start auto swing

Press .

• “ ” is displayed on the LCD.

• The flap (horizontal blade) will begin to swing.

■

To set the flap at desired position

• This function is effective while flap is in auto swing mode.

Press when the flap has reached the

desired position.

• The flap will stop moving.

• “ ” disappears from the LCD.

Upper and lower airflow direction

01_EN_3P257186-2A.fm Page 11 Saturday, October 31, 2009 2:19 PM

12

Adjusting the Airflow Direction

■

To adjust the louvers (vertical

blades)

Hold the knob and move the louvers.

(You will find a knob on the left-side and the right-side

blades.)

• When the unit is installed in the corner of a room, the

direction of the louvers should be facing away from the

wall.

If they face the wall, the wall will block off the wind,

causing the cooling (or heating) efficiency to drop.

CAUTION

NOTE

• Always use a remote controller to adjust the angles of the flap. If you attempt to move it

forcibly with hand when it is swinging, the mechanism may be broken.

• Be careful when adjusting the louvers. Inside the air outlet, a fan is rotating at a high speed.

■ Notes on the angles of the flap

• The flap swinging range depends on the

operation. (See the figure.)

• If the air conditioner is operated in HEAT or

DRY operation with the flap kept stopped in

the downward direction, the flap will

automatically start operating in approx. an

hour in order to prevent dew condensation.

45˚

5˚

45˚

5˚

15˚

45˚

50˚

0˚

In DRY operation or COOL operation

Upper limit

Lower limit

Upper limit

Lower limit

Upper limit

Lower limit

Stop operation

In HEAT operation

In FAN operation

COMFORT AIRFLOW

01_EN_3P257186-2A.fm Page 12 Saturday, October 31, 2009 2:19 PM

13

English

COMFORT AIRFLOW Operation

The flow of air will be in the upward direction while in COOL operation and in the downward direction

while in HEAT operation, which will provide a comfortable wind that will not come in direct contact with

people.

■

To start COMFORT AIRFLOW

operation

1. Press .

• The flap position will change, preventing air from blowing

directly on the occupants of the room.

• “ ” is displayed on the LCD.

• Airflow rate is set to Auto.

COOL/DRY: The flap will go up.

HEAT: The flap will go down.

■

To cancel COMFORT AIRFLOW

operation

2. Press again.

• The flap will return to the memory position from before

COMFORT AIRFLOW mode.

• “ ” disappears from the LCD.

NOTE

COOL operation HEAT operation

■ Notes on COMFORT AIRFLOW operation

• The flap position will change, preventing air from blowing directly on the occupants of the

room.

• POWERFUL operation and COMFORT AIRFLOW operation cannot be used at the same

time.

Priority is given to the function of whichever button is pressed last.

• The airflow rate will be set to Auto. If the upper and lower airflow direction is selected, the

COMFORT AIRFLOW operation will be canceled.

01_EN_3P257186-2A.fm Page 13 Saturday, October 31, 2009 2:19 PM

14

POWERFUL Operation

POWERFUL operation quickly maximizes the cooling (heating)

effect in any operation mode. You can get the maximum capacity.

■

To start POWERFUL operation

1. Press .

• POWERFUL operation ends in 20 minutes. Then the

system automatically operates again with the previous

settings which were used before POWERFUL operation.

• “ ” is displayed on the LCD.

■

To cancel POWERFUL operation

2. Press again.

• “ ” disappears from the LCD.

NOTE

■ Notes on POWERFUL operation

• When using POWERFUL operation, there are some functions which are not available.

•

POWERFUL operation cannot be used together with ECONO or COMFORT AIRFLOW operation.

Priority is given to the function of whichever button is pressed last.

• POWERFUL operation can only be set when the unit is running.

• POWERFUL operation will not increase the capacity of the air conditioner if the air

conditioner is already in operation with its maximum capacity demonstrated.

• In COOL and HEAT operation

To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased

and the airflow rate be fixed to the maximum setting.

The temperature and airflow settings are not variable.

• In DRY operation

The temperature setting is lowered by 2.5°C and the airflow rate is slightly increased.

• In FAN operation

The airflow rate is fixed to the maximum setting.

• In AUTO operation

To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased

and the airflow rate be fixed to the maximum setting.

01_EN_3P257186-2A.fm Page 14 Saturday, October 31, 2009 2:19 PM

15

English

ECONO Operation

ECONO operation is a function which enables efficient operation by

limiting the maximum power consumption value.

This function is useful for cases in which attention should be paid to

ensure a circuit breaker will not trip when the product runs

alongside other appliances.

■

To start ECONO operation

1. Press .

• “ ” is displayed on the LCD.

■

To cancel ECONO operation

2. Press again.

• “ ” disappears from the LCD.

• This diagram is a representation for illustrative purposes only.

* The maximum running current and power consumption of the air conditioner in ECONO

operation vary with the connecting outdoor unit.

NOTE

■ Notes on ECONO operation

• ECONO operation can only be set when the unit is running.

• ECONO operation is a function which enables efficient operation by limiting the power

consumption of the outdoor unit (operating frequency).

• ECONO operation functions in AUTO, COOL, DRY and HEAT operation.

• POWERFUL and ECONO operation cannot be used at the same time.

Priority is given to the function of whichever button is pressed last.

• If the level of power consumption is already low, ECONO operation will not drop the power

consumption.

Running current and

power consumption

From start up until set

temperature is reached

Time

Maximum during

normal operation

Maximum during

ECONO operation

Normal

operation

ECONO

operation

01_EN_3P257186-2A.fm Page 15 Saturday, October 31, 2009 2:19 PM

16

OFF TIMER Operation

Timer functions are useful for automatically switching the air

conditioner on or off at night or in the morning. You can also use

OFF TIMER and ON TIMER in combination.

■

To use OFF TIMER operation

1. Press .

Each pressing of advances the time setting by 1 hour.

The time can be set between 1 to 9 hours.

• The TIMER lamp lights up.

■

To cancel OFF TIMER operation

2. Press .

• “ ” disappears from the LCD.

• The TIMER lamp goes off.

NOTE

“ ” is displayed on the LCD.

■ Note on TIMER operation

• Once you set ON/OFF TIMER, the time setting is kept in the memory. The memory is

canceled when remote controller batteries are replaced.

■ NIGHT SET mode

When the OFF TIMER is set, the air conditioner automatically adjusts the temperature

setting (0.5°C up in COOL, 2.0°C down in HEAT) to prevent excessive cooling (heating) for

your pleasant sleep.

01_EN_3P257186-2A.fm Page 16 Saturday, October 31, 2009 2:19 PM

17

English

ON TIMER Operation

■

To use ON TIMER operation

1. Press .

Each pressing of advances the time setting by 1 hour.

The time can be set between 1 to 12 hours.

• The TIMER lamp lights up.

■

To cancel ON TIMER operation

2. Press .

• “ ” disappears from the LCD.

• The TIMER lamp goes off.

■

To combine ON TIMER and OFF TIMER

• A sample setting for combining the 2 timers is shown below.

• “ ” and “ ” are displayed on the LCD.

NOTE

“ ” is displayed on the LCD.

■ In the following cases, set the timer again.

• After a breaker has turned off.

• After a power failure.

• After replacing batteries in the remote controller.

Display

01_EN_3P257186-2A.fm Page 17 Saturday, October 31, 2009 2:19 PM

18

CARE

Care and Cleaning

■

Indoor unit, outdoor unit and remote controller

1. Wipe them with dry soft cloth.

■

Front panel

1. Open the front panel.

• Hold the front panel by the panel tabs

on the both sides and open it.

2. Remove the front panel.

• Slide the front panel to either the left

or right and pulling it toward you.

This will disconnect the front panel

shaft on one side.

• Disconnect the front panel shaft on the

other side in the same manner.

3. Clean the front panel.

• Wipe it with a soft cloth soaked in water.

• Only neutral detergent may be used.

• In case of washing the panel with water, wipe it with dry soft cloth, dry it up in the shade after

washing.

4. Attach the front panel.

• Align the front panel shaft on the left

and right of the front panel with the

slots, then push them all the way in.

• Close the front panel slowly.

(Press the panel at both sides and the

center.)

CAUTION

Before cleaning, be sure to stop the operation and

turn the breaker off.

Units

• Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an

injury.

• When removing or attaching the front panel, use a robust and stable stool and watch your

steps carefully.

• When removing or attaching the front panel, support the panel securely with hand to prevent

it from falling.

• For cleaning, do not use hot water above 40°C, benzine, gasoline, thinner, nor other volatile

oils, polishing compound, scrubbing brushes, nor other hand stuff.

• After cleaning, make sure that the front panel is securely fixed.

Panel tab

Front

panel shaft

01_EN_3P257186-2A.fm Page 18 Saturday, October 31, 2009 2:19 PM

19

English

1. Pull out the air filters.

• Open the front panel.

• Push a little upwards the tab at the center of each air

filter, then pull it down.

2. Take off the titanium apatite

photocatalytic air-purifying filter.

• Hold the recessed parts of the frame and unhook the

4 claws.

3. Clean or replace each filter.

3-1 Air filter

3-1-1 Wash the air filters with water or clean

them with vacuum cleaner.

• If the dust does not come off easily, wash

them with neutral detergent thinned with

lukewarm water, then dry them up in the

shade.

• Be sure to remove the titanium apatite

photocatalytic air-purifying filter.

• It is recommended to clean the air filters

every 2 weeks.

Filters

Titanium apatite

photocatalytic

air-purifying filter

Air filter

Filter frame

Claw

01_EN_3P257186-2A.fm Page 19 Saturday, October 31, 2009 2:19 PM

La page charge ...

Acson A5WMY15KR Mode d'emploi

Ce manuel convient également à

Acson A5WMY15KR Mode d'emploi

dans d''autres langues

Autres documents