™
Warnings and considerations
WARNING! Turn OFF electrical power before installing or servicing this
product. Improper use or installation can cause SERIOUS INJURY, DEATH
or LOSS/DAMAGE OF PROPERTY.
ATTENTION! Coupez l’alimentation électrique avant d’installer ou de
réparer ce produit. Une mauvaise installation ou utilisation peut entraîner
des blessures graves, décès ou perte / dommages à la propriété.
WARNING! This device must be protected by a circuit breaker (20A max).
ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)
WARNING! Ground this device in accordance with the National Electric
Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s
contact with a metal wallbox for adequate grounding. Use the device’s
ground wire to make a secure connection to the safety ground of the
electrical system.
ATTENTION! Cet appareil doit être en conformité avec le Code national de
l’électricité (NEC). Ne comptez pas uniquement au contact de la plaque
avant avec un boîtier mural métallique pour la mise à la terre adéquate.
Utilisez cet appareil à la terre de l’appareil pour établir une connexion
sécurisée au système électrique.
IMPORTANT! This device must be installed by a licensed electrician in
accordance with all national and local electrical codes.
IMPORTANT! If you are unsure about any part of these instructions,
consult a qualified electrician.
IMPORTANT! Use this device only with copper or copper-clad wire. Do
not use aluminum wiring. This product has not been approved for use with
aluminum wiring.
IMPORTANT! Using this product in a manner other than outlined in this
document voids your warranty. Further, Control4 is NOT liable for any
damage incurred with the misuse of this product. See “Troubleshooting.”
IMPORTANT! Do NOT use a power screwdriver to install this device. If you
do, you may overtighten the screws and strip them. Also, overtightening
the screws may interfere with proper button operation.
IMPORTANT! This is an electronic device with intricate components.
Handle and install with care!
IMPORTANT! When used in conjunction with an Auxiliary Keypad
(C4-KA-xx), the wire connecting the Auxiliary Keypad to the Configurable
Keypad must not exceed 45 m (150 ft.) at 120V AC, and 30 m (100 ft.) at
277VAC.
Installation instructions
1 Ensure that the location and intended use meet the following criteria:
• When replacing a traditional 3-way switch, refer to the “Two-Location”
sample wiring configurations provided in the appropriate load control
device installation guide.
• Install in accordance with all national and local electrical codes.
• The range and performance of the wireless control system is highly
dependent on the following: (1) distance between devices; (2) layout
of the home; (3) walls separating devices; and (4) electrical equipment
located near devices.
2 Turn o the local electrical power by either switching o the circuit breaker or
removing the fuse from the fuse box. To ensure the wires do NOT have power
running to them, use an inductive voltage detector.
Supported model
• C4-KC120277 Wireless Configurable Keypad
Introduction
The Control4® Configurable Keypad is intended for use in a Control4 system. It
installs in a standard wallbox using typical wiring standards and communicates to
the Control4 system using a wireless connection.
Box contents
• Configurable Keypad
• Keycap Button Kit
• Wire nuts
• Warranty card
• Configurable Keypad Installation Guide (this document)
• Keypad Button Installation Guide
Specifications
The specifications are described below.
Model number C4-KC120277-xx
Power requirements 120-277V AC +/-10% 50/60 Hz
36-48V DC
This device requires a neutral AC connection.
Power consumption 120V: 350mW
277V: 540mW
36V DC: 430mW
Environmental
Operational temperature 0 to 40 ˚C (32 to 104 ˚F)
Humidity 5% to 95% non-condensing
Storage -20 to 70 ˚C (-4 to 158 ˚F)
Miscellaneous
Control communications Zigbee, IEEE 802.15.4, 2.4 GHz, 15-channel
spread spectrum radio
Wallbox volume 4.75 cubic inches
Weight 0.05 kg (0.12 lb.)
Shipping weight 0.08 kg (0.18 lb.)
Configurable
Keypad
Installation Guide
Copyright ©2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and
their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC,
dba “Control4” and/or dba “SnapAV” in the United States and/or other countries. Snap AV and
Wirepath are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other
names and brands may be claimed as the property of their respective owners. All specifications
subject to change without notice.
200-00309-F 2020-02-20 MS
NOTE: The wallbox wiring shown in this document is an example. Your
wire colors and functions may dier. If you are not sure which wires are
the Line In/Hot, Neutral, and Earth Ground wires, have a trained electrician
do the installation.
3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch
from the wire end (see Figure 1).
Figure 1.
Strip wire insulation
IMPORTANT!
Not grounding this product, as described in the section,
“Warnings and Considerations,” may result in an installation less immune
to damage caused by electrical disturbances, such as ESD or lightning,
and may void the warranty.
4 Identify and connect the keypad wires to the wallbox wires using the wire
nuts as shown in Figure 2 below.
Figure 2. Keypad wiring
TIP:
If you are using a Control4 push-on (screwless) faceplate in a multi-
gang installation, attach the black faceplate sub-plate to all of the devices
that will be installed into the wallbox prior to attaching the devices to the
wallbox. This will help ensure that all the devices are properly aligned and
on the same plane after installation.
5 Fit the wires back into the wallbox. Bend the wires in a zigzag pattern so that
they easily fold into the wallbox (Figure 3).
Figure 3.
Bend the wires
6 Align the keypad to the wallbox (the model # label should be at the bottom)
and fasten it with screws. Tighten the screws until the back side of the yoke
plate is even with the wall surface, but no further. Overtightening can warp
the configurable keypad and cause mechanical malfunction.
7 Install the Top Actuator Bar, Bottom Sensor Bar, and buttons following the
instructions in the “Button Installation” section below.
8 Install the Control4 Faceplate following the instructions in the Faceplate
Installation Guide or attach a standard Decora-style faceplate.
9 Turn on power at the circuit breaker or replace the fuse from
the fuse box.
Button installation
For information about how to install or remove the buttons on the configurable
keypad, see the Keypad Buttons Installation Guide.
Operation and configuration
On initial power up, all status LEDs on the keypad will illuminate green indicating
that the device has power. Until the keypad has been configured into a Control4
system, it will not control any loads. To set up this keypad for use with a Control4
system, refer to the Composer Pro User Guide.
Button tap sequences
The button tap sequences are defined in the table below. Button tap sequences
that require a single (1) button should use the top-most button installed on the
keypad. Button tap sequences requiring two (2) buttons should use the top-most
and bottom-most buttons installed on the keypad.
Function Button sequence
Identify 4
Zigbee channel 7
Reboot 15
Factory reset 9-4-9
Leave mesh and reset 13-4-13
Troubleshooting
If the LEDs do not light up indicating that the keypad is receiving power::
• Ensure circuit breaker is not turned OFF or tripped.
• Check for proper wiring (see Step 2 in “Installation Instructions”).
Care and cleaning
• Do NOT paint the keypad or its wall plate.
• Do NOT use any chemical cleaners to clean the keypad.
• Clean surface of the keypad with a soft damp cloth as needed.
Regulatory/safety information
To review regulatory information for your particular Control4 products, see the
information located on the Control4 website at
ctrl4.co/reg
.
Warranty
For complete warranty information, including details on consumer legal rights as
well as warranty exclusions, visit
ctrl4.co/warranty
.
Patent information
Applicable patents are available at
ctrl4.co/patents
-
1
-
2
Control 4 C4-KC120277-BL Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
Control4 C4-TV120277-BL Guide d'installation
-
-
Delta EIDWU25TSUB02 Manuel utilisateur
-
Control4 C4-V-ROSW120 Manuel utilisateur
-
Control4 CORE1 Guide d'installation
-
-
Control4 C4-CORE3 Guide d'installation
-
-
-
Episode EA-MINI-SUB-1D-100 Guide d'installation