LG WD-14311RD Le manuel du propriétaire
- Catégorie
- Machines à laver
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
P/No.: MFL31245120
Washing Machine
OWNER’S MANUAL
WM3431H*
WM3434H*
Designed specially to use only HE (High Efficiency) detergent
Conçu exclusivement pour les détersifs HE (haute efficacité)
roduct Feature
P
ontents
C
2
Important Safety Information...........................................................3
Specification....................................................................................4
Installation.......................................................................................5
Preparation Before Washing.........................................................10
Adding detergent...........................................................................11
Cycles .........................................................................................12
How to Use Washer......................................................................13
Maintenance..................................................................................17
Troubleshooting Guide..................................................................20
Warranty........................................................................................23
Automatic Process From Washing To Drying.
Automatic process from washing to drying can be selected easily.
More economical by Intelligent Wash System
Intelligent Wash System detects the amount of load and water
temperature, and then determines the optimum water level and
washing time to minimize energy and water consumption.
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Child-Lock
The Child-Lock prevents children from pressing any button to
change the settings during operation.
Built-in Heater
Internal heater automatically heats the water to the best
temperature on selected cycles.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes
load to minimize the spinning noise level.
Auto Restart
If the washing machine is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
Designed specially to use only HE (High Efficiency)
detergent
mportant Safety Information
I
3
For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
• Read all instructions before using the washer.
• Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other
flammable or explosive substances, as they give
off vapors that could ignite or explode.
• Do not add gasoline, dry cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode.
• Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not
been used for such a period, before using the
washing machine, turn on all hot water faucets
and let the water flow from each for several
minutes. This will release any accumulated
hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children.
• Before the washer is removed from service or
discarded, remove the door to prevent children
from hiding inside.
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• See Installation Instructions for grounding
requirements.
• Do not use heat to dry articles containing foam
rubber or similarly textured rubber-like materials.
• Interior of washer and condensing duct should be
cleaned periodically by qualified service
personnel.
• ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
• Do not place items exposed to cooking oil in your
dryer, Items contaminated with cooking oils may
contribute to a chemical reaction that could cause
a load to catch fire.
• Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a
cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not use an adapter or extension cord.
• Do not remove ground prong.
• If you don’t have the proper outlet, consult an electrician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the
washer, follow basic precautions, including the following:
SAVE THESE INSTRUCTIONS
WARNING :
Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
!
!
4
pecification
S
Name: Front-loading Washing Machine
Power supply : 120V~, 60Hz
Size: 23
3
/
8
” 25
3
/
8
” 33
1
/
4
”42
17
/
32
” (D, door open)
595 mm 645 mm 845 mm, 1080 mm (D, door open)
Weight: 147 lbs. (66.7 kg)
Spin speed: 1400 rpm max. (WM3431H*)
1200 rpm max. (WM3434H*)
Permissible water pressure: 4.5 ~ 145 PSI (30 ~ 1000 kPa)
❋ Specifications subject to change by manufacturer.
Hose retainer
Hot/Cold (1 each)
Hose
Wrench
Tide
for removing shipping bolts
and leveling the washer
Tie strap
to secure drain hose to standpipe,
inlet hose, or laundry tub
Cap (4 each)
to cover the holes created after
removing the shipping bolts
Accessories
nstallation
I
5
1. To prevent internal damage during transport,
4 locking bolts are installed. Before operating
the washer, remove the bolts.
• If they are not removed, it may cause severe
vibration, noise, and malfunction.
3. Take out the 4 bolts by twisting the braces
slightly. Keep the 4 bolts and the wrench for
future use.
• Whenever the appliance is transported, the
shipping bolts must be replaced.
2. Unscrew the 4 bolts with the wrench
supplied.
4. Close the holes with the caps supplied.
The appliance is fitted with shipping bolts to prevent internal damage during transport.
Shipping bolts
Install or store unit where it will not be exposed to temperatures below freezing or
exposed to outside weather conditions.
Properly ground washer to conform with all governing codes and ordinances.
To reduce the risk of electric shock, do not install the washer in humid spaces.
The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted
floor.
In areas where there are areas which may be subject to infestation by cockroaches or other vermin, pay
particular attention to keeping the appliance and its surroundings in clean condition at all times.
Damage caused by cockroaches or other vermin will not be covered by the appliance warranty.
Removing shipping bolts
cap
nstallation
I
6
Installation clearances
The location must be large enough to fully
open the washer door.
Washer dimensions
• Most installations require a minimum 4 in.
(10 cm) clearance behind the washer.
Minimum installation spacing
for recessed area installation.
The following dimensions shown are for the
minimum spacing allowed.
Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required for
wall, door and floor moldings.
• Additional spacing of 1 in. (2.5 cm) on all
sides of the washer is recommended to
reduce noise transfer.
Companion appliance spacing should also be
considered.
23
3
/
8
"
(59.5 cm)
25
3
/
8
"
(64.5 cm
)
33
1
/
4
"
(84.5 cm)
42
17
/
3
2
"
(108 cm)
25
3
/
8
"
(64.5 cm)
4"
(10 cm)
23
3
/
8
"
(59.5 cm)
1"
(2.5 cm)
1"
(2.5 cm)
Level floor
Power outlet
• Allowable slope under entire washer is 1°.
• To minimize noise and vibration, the
washer MUST be installed on a solidly
constructed floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the washer on a platform or
weakly supported structure.
• Must be within 60 in. (1.5 m) of either side of
the washer. Do not overload the outlet with
more than one appliance.
• Time-delay fuse or circuit breaker is
recommended.
[Front view]
[Side view]
It is the personal responsibility and
obligation of the customer to have a
proper outlet installed by a qualified
electrician.
A firm, solid floor is even more critical
to a front-loading washer than to a
top-loader. If your floor is wood and/or
frame construction, you may need to
reinforce it. Front-loaders use
substantially faster spin speeds than
top-loaders, causing greater vibration.
If the floor is not solid, your washer will
vibrate. You will hear and feel the
vibration throughout your house.
7
nstallation
I
• Water supply pressure must be between
4.5 and 145 PSI (30~1000 kPa)
• Do not crossthread when connecting inlet
hose to the valve.
• If the water supply pressure is more than
145 PSI, a pressure reducing device should
be installed.
• Two Sealing washers are supplied with the
water inlet hoses to prevent water leaks.
• Check for leakage of washing machine
connections by turning the tap completely on.
• Periodically check the condition of the hose
and replace the hose if necessary.
• Make sure that there is no kink in the hose
and that it is not crushed.
• Be sure that the two water input ports are
connected to the correct water faucets.
The connector for hot water is colored red.
Washing Machine is to be connected to the water mains using new hoses
Old hoses should not be used.
Connecting water supply hose
Electrical connection
• Do not use an extension cord or double adapter.
• If the supply cord is damaged, it must be replaced by a qualified person in order to avoid a hazard.
• If the machine will not be used for an extended time, unplug it and shut off the water supply.
• Connect the machine to a grounded outlet in accordance with current wiring regulations.
• The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center.
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the
washing machine at room temperature for a few hours before putting it into operation.
8
nstallation
I
Installation of drain hose
max. 47"
min. 24"
max. 47"
max. 47"
max. 47"
min. 24"
• The drain hose should not be placed higher than 47” above the floor.
• Properly securing the drain hose will protect the floor from damage due to water leakage.
This equipment is not designed for maritime use or for mobile installations such as in
RV’s, aircraft, etc.
Turn off the faucet if the machine is to be left for an extended period of time (e.g. holiday).
When disposing of the appliance, cut off the power cable, and destroy the plug.
Disable the door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging from children.
• When installing the drain hose at a sink,
secure it so it cannot break away and
cause flooding and damage.
• Properly securing the drain hose will
protect the floor from damage due to
water leakage.
9
nstallation
I
Level adjustment
Concrete floors
Wooden floors
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably in a
corner of the room.
2. If the floor is uneven, adjust the adjustable feet as required. (do not
insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate
diagonally, the machine should not move up and down at all. (Please,
check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust
the feet again.
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mat and level the machine to suit (Cut the Tread Mat into 2
3
/
4
inch
squares and stick the pieces to the dry tile where machine is to be placed).
Tread Mat is a self adhesive material used on ladders & steps to prevent slipping.
• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with screws.
• If possible install the washer in one of the corners of the room, where the floor is more stable.
Insert the rubber cups to reduce vibration.
You can obtain the rubber cups (p/no.4620ER4002B) from the LG parts dept.
Important!
• Proper placement and levelling of the washer ensure long,regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If the washer feet get wet, slipping may occur.
Rubber Cup
Timber or suspended type flooring may contribute to
excessive vibration and unbalance errors.
10
reparation Before Washing
P
1. Fabric Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your
garment and how it should be washed.
2. Sorting
To get the best results, sort clothes into loads that can be washed with the same wash cycle.
Different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer
can occur causing discoloration of white clothing. If possible, do not wash heavily soiled
items with lightly soiled ones.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lights, Darks) Separate white fabrics from colored fabrics.
Lint (Lint Producers, Collectors) Wash lint producers and lint collectors
separately.
3. Check before loading
WARNING - To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
• Check all pockets to make sure
that they are empty. Things such
as nails, hair clip, matches, pens,
coins and keys can damage both
your washer and your clothes.
• Close zippers, hooks, and strings
to make sure that these items don’t
snag on other clothes.
• Pre-treat dirt and stains by
brushing a little detergent dissolved
in water onto stains like collars and
cuffs to help shift dirt.
Do not wash or spin water-proof clothes.
!
Before the first washing
Select the Normal cycle, add about 1/2 the recommended amount of detergent in the dispenser, and allow
the unit to wash without clothing. This will remove any residue from the drum that may remain after
manufacturing.
11
dding detergent
A
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing
of the fabric softener which could stain
clothes.
• Do not leave the fabric softener in the
detergent drawer for more than 2 days.
(Fabric softener could harden)
• Softener will automatically be added
during last rinse cycle.
• Do not open the drawer when water is
supplied.
• Solvents (benzene, etc.) are not
allowable.
1. The Dispenser Drawer
Your LG washer is designed to use only High
Efficiency (HE) detergents.
HE detergents are formulated specifically for
front load washers and contain suds reducing
components.
HE detergents make less suds, improve
washing and rinsing performance, and help to
keep the interior
of your LG washer clean.
If a regular detergent is used, it may cause
oversudsing and unsatisfactory performance.
For the best washing and rinsing
performance, low-sudsing HE detergents are
strongly recommended.
• Because reducing the amount of
detergent may reduce cleaning, it is
important to pretreat stains, sort carefully
by color and soil level, and avoid
overloading.
• Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid using too much detergent.
• Detergent is dispensed at the beginning of
the cycle.
4. Detergent usage
• Do not open the dispenser drawer during
water fill cycle.
• Bleach will be dispensed automatically
after the detergent has had time to work.
• Do not exceed the maximum fill line.
3. The liquid bleach dispenser
2. Adding Fabric Softener
Adding detergent and fabric softener
Do not pour fabric softener
directly on the clothes
Designed specially to use only
HE(High Efficiency) detergent
12
ycles
C
1) Automatic wash load (weight) detection:
Automatically detects the load and optimizes the washing time. After detecting, the
estimated time remaining in the cycle will be displayed.
Select cycles designed for different types of fabric and soil levels.
13
ow to use washer
H
• Rotate the Cycle selector knob to
select cycle designed for different types
of fabric and soil levels.
• Each cycle has a preset Water
Temperature, Spin Speed, Soil Level,
and Option (See page 12).
• The preset settings can be changed
anytime before Start.
2. Cycles
• Use this button to turn the Power On/Off.
1. Power ( )
• Use this button to start/stop the washer.
3. Start/Pause ( )
• Allows the start of any cycle to be delayed
for 1~19 hours.
• Choose the wash cycle for your load, and
then press the Delay Wash button once
for one hour or press the button again to
increase the delay wash time up to 19
hours in one hour increments.
4. Delay Wash
• This option provides an additional rinse.
• Use this option to ensure the removal of
detergent or bleach residue from garments.
5. Extra Rinse
This front load washer requires
longer cycle time and gets clothes
much cleaner, yet is more gentle
on the fabrics, than top load
washers. Washing time can be
reduced significantly for small
loads or lightly soiled loads by
selecting Speed Wash with the
Cycle knob and setting the Soil
Level button at Light.
14
ow to use washer
H
• Select a water temperature based on
the type of load you are washing.
• Follow the fabric care label and chart
below for best results.
• Warm rinses leave the loads dryer than
cold rinses. Warm rinses increase
wrinkling.
• In cold climates, a warm rinse makes the
load more comfortable to handle.
• Cold rinses save energy.
• The Cold rinse temperatures depend on
the cold water at your faucet.
6. Wash/Rinse Temperature
• To change the spin speed, press the
Spin Speed button repeatedly to cycle
through available options.
7. Spin speed
• To change the soil level, press the
Soil Level button repeatedly until the
desired setting is on.
8. Soil Level
Suggested Wash Temp.
Garment
Kitchen towels, sheets,
and baby garments
Whites and Heavy
soiled color-fast items
Most loads
Brightly colored items,
washable woolens
Extra Hot
Hot
Warm
Cold
15
ow to use washer
H
1) Drying Automatic guide
2) Drying time guide
• Drying options are easily selected with the Dry
button.
• For most even drying , make sure all articles in the
clothes load are similar in material and thickness.
• Do not overload dryer by stuffing too many articles
into drum. Items must be able to tumble freely
• If you open door and remove load before dryer has
finished its cycle, remember to press the
Start/Pause button.
• By pressing the Dry button, you can select
• Use your Automatic Cycles to dry most loads.
Electronic sensors measure the temperature of the
exhaust to increase or decrease the drying
temperature for faster reaction time and tighter
temperature control.
• Recommended Dry selection according to fabric type:
a) Perm Press - Low Temp.
b) If clothes are to be ironed - Less
c) Cotton/Towels - Normal
d) Diapers - More
The estimated drying time varies from the
actual drying time with an Automatic.
The type of fabric, size of the load, and the
dryness selected affect drying time.
• By pressing the Dry button, the drying time can
be selected.
• Timed dry can last up to 150 min. When
selecting Dry only, drying will start after
spinning.
• These drying times are given as a guide to help
you set your dryer for manual drying. Drying
times can vary greatly depending on dampness,
room temperature and type of fabric. Your own
experience will be your best guide.
- Do not tumble dry woolen articles. Pull them to
their original shape and dry them flat.
Woolen Articles
- Some woven and loopknit materials may shrink,
by varying amounts, depending on their quality.
- Always stretch them out immediately after
drying.
Woven and Loopknit Materials
- Do not overload your dryer.
- Take out permanent press articles as soon as
the dryer stops to reduce wrinkles.
Permanent Press and Synthetics
- Always check the manufacturer's instructions.
Fiber or Leather Materials
- Always check the manufacturer's instructions.
Baby clothes and Night Gowns
- Do not dry any items made from or containing
rubber or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and table cloths
c) bathmats
Rubber and Plastics
- Do not dry fiberglass articles in your dryer. Glass
particles left in the dryer could be picked up by
your clothes the next time you use the dryer and
irritate your skin.
Fiber glass
➔
➔
➔
Normal
Low Temp.
Less
Off
➔➔
More Time
9. Dry
• Your dryer can handle a load of up to 9 lbs.
(4 kg) dry weight of articles.
• When drying cycle is completed, (Cool Down)
is displayed on the Multi display.
• Cool Down is set automatically when the drying
cycle is complete.
• If clothes are not removed promptly when the
drying cycle ends, wrinkles can form.
• The Cool Down feature periodically tumbles,
rearranges and fluffs the load to avoid wrinkles for
up to 4 hours.
• The message will continue to display until the
clothes are removed or the Start/Pause button is
pressed.
16
ow to use washer
H
OPTION
MULTI DISPLAY
STATUS INDICATOR
CHILD LOCK
DOOR LOCKED
• If the laundry is heavily soiled, Extra
Wash option is effective.
• Available in Sanitary, Cotton/Towels,
Normal and Perm Press cycles.
2. Extra Wash
• Lights whenever the door of the washer
is locked.
• The door can be unlocked by pressing
the Start/Pause ( ) button to stop the
washer. It will unlock after 1~2 minutes.
If the water temperature or the
level is too high, the door cannot be
unlocked.
Do not try to force the door open
when
DOOR LOCKED ( )
lights on.
• These lights show which portion of the
cycle the washer is operating.
• This display shows:
a) the estimated time remaining in the
cycle when operating,
b) the error code when an error has
been detected.
• Use this option to prevent unwanted use
of the washer. Press and hold Delay
Wash button for 3 seconds to
lock/unlock control.
• When Child lock is set, lights
and all buttons are disabled except the
Power ( ) button. You can lock the
washer while it is operating.
• Provides a set time for soaking, then
automatically moves into the wash cycle.
• Use this option to wash normal clothes or
thick and heavy clothes which are
excessively dirty.
1. Soak
• Use this option to select spin cycle only.
4. Spin Only
• Use this option to rinse and then spin.
3. Rinse+Spin
• When you want dry only, select this
option.
5. Dry Only
17
aintenance
M
The water inlet filter
- " " error message will blink on the control panel when water does not enter the
detergent drawer.
- If your water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged. We recommend cleaning it every few months.
The drain pump filter
❋
The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
❋
Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock
hazards.
❋
When disposing of the appliance, cut off the mains cable, destroy the plug, and disable the door
lock to prevent young children being trapped inside.
1. Turn off the
water tap.
2. Unscrew the
water inlet
hose.
3. Clean the
filter using a
hard bristle
brush.
4. Tighten the
inlet hose.
1. Open the lower cover
cap () with a tool
such as coin.
Turn the drain plug
() to pull out the
hose.
2. Unplug the drain plug (),
allowing the water to flow out.
At this time use a vessel to
prevent water from flowing
onto the floor. When water
does not flow any more, turn
the pump filter () open to
the left.
3. Remove any foreign
objects from the pump filter
(). After cleaning, turn the
pump filter () clockwise
and insert the drain plug
() to the original place.
Close the lower cover
cap().
• Allow the water to cool down before cleaning the drain pump filter.
CAUTION
Drain, using the drain hose, before opening the pump filter to remove objects.
Be careful when draining if the water is hot.
18
aintenance
M
Dispenser drawer
❋ After a while detergents and fabric softeners leave a deposit in the drawer.
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downward and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
The drawer recess
❋ Detergent can also accumulate inside the recess which should
be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
The washing drum
• If you live in a hard water area, lime scale can continuously build up in places where it cannot be seen
and it is not easily removed from the drum. Over time the build-up of scale clogs appliances, and if it is
not kept in check, these will eventually have to be replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal
articles (paper clips, safety pins, etc.) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes, or bleaches, make sure they are suitable for washing machine use.
• Descaler could contain components that can damage part of your washing machine.
• Remove the spots with a stainless steel cleaning agent.
• Never use steel wool.
MAX
max
M
A
X
MAX
M
A
X
19
aintenance
M
Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral, non-
abrasive household detergent.
Immediately wipe off any spills with a damp cloth.
Try not to damage the surface with sharp objects.
IMPORTANT: Do not use methylated spirit, solvents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass. These areas
should always be clean to ensure a water-tight seal.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
Remove hard water deposits using only cleaners labeled as safe for washing
machines.
Winterizing instructions
If the washer is stored in an area where freezing can occur or moved in freezing
temperatures, follow these winterizing instructions to prevent damage to the washer:
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1 gallon (3.8
) nontoxic recreational vehicle (RV) antifreeze to empty wash
drum. Close door.
5. Set spin cycle and let washer spin for 1 minute to drain out all the water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry drum interior, and close door.
7. Remove the two-compartment container from the Dispenser. Drain any water in
compartments and dry the compartments.
8. Store washer in an upright position.
9. To remove antifreeze from washer after storage, run empty washer through a
complete cycle using detergent. Do not add laundry.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
LG WD-14311RD Le manuel du propriétaire
- Catégorie
- Machines à laver
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: LG WD-14311RD Owner's manual
Documents connexes
-
LG WD-12590RD Le manuel du propriétaire
-
LG WD-13330TD Le manuel du propriétaire
-
LG WM3431HW/01 Le manuel du propriétaire
-
-
LG FH6G1BCHK6N Le manuel du propriétaire
-
-
-
LG WM2487HWM Le manuel du propriétaire
-
LG WM2016CW Le manuel du propriétaire
-