LG 1177675 Manuel utilisateur

ENGLISH ESPAÑOL FRANÇAIS

OWNER'S MANUAL

WASHING

MACHINE

Please read this owner's manual thoroughly before operating and keep

it handy for reference at all times.

WM3400CW

MFL71693702

Rev.00_121619

www.lg.com

2

3 SAFETY INSTRUCTIONS

3 IMPORTANT SAFETY INSTRUCTIONS

7 PRODUCT OVERVIEW

7 Parts

7 Accessories

8 INSTALLATION

8 Tools Needed

8 Installation Overview

9 Product Specifications

10 Choosing the Proper Location

11 Unpacking and Removing Shipping Bolts

12 Connecting the Water Lines

13 Connecting the Drain Hose

14 Leveling the Washer

15 Connecting to the Power Supply

15 Testing the Washer

16 OPERATION

16 Using the Washer

1717 Sorting Laund

18 Loading the Washer

Adding Cleaning Produc1818

21 Control Panel

Wash Cycl2323

Cycle Gui2424

TABLE OF CONTENTS

28 MAINTENANCE

28 Regular Cleaning

30 Cleaning the Door Seal

30 Cleaning the Water Inlet Filters

31 Cleaning the Drain Pump Filter

32 Care in Cold Climates

33 TROUBLESHOOTING

33 FAQs: Frequently Asked Questions

34 Before Calling for Service

42 LIMITED WARRANTY

42 USA

45 CANADA

49 Warranty Exceptions (U.S. and Canada)

3SAFETY INSTRUCTIONS

ENGLISH

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others.

All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

If you do not follow instructions, it could result in death or serious injury.

CAUTION

If you do not follow instructions, it could result in minor or moderate injury or damage to the product.

All safety messages tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell

you what may happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of explosion, re, death, electric shock, scalding or injury

to persons when using this product, follow basic precautions, including the

following:

INSTALLATION

• Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety

glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

• Before use, the appliance must be properly installed as described in this manual.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Refer to the INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions

are packed with the appliance for the installer’s reference. If the appliance is moved to a new location, have

it checked and reinstalled by qualied service personnel.

• Moving or installation of the appliance requires two or more people.

• Do not install the appliance in humid spaces.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions.

• This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or aircraft.

4 SAFETY INSTRUCTIONS

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children might

use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers.

• The appliance must be installed and electrically grounded by qualied service personnel in accordance with

local codes.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.

• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

• This appliance must be positioned near to an electrical power supply.

• Disconnect the power cord, house fuse or circuit breaker before installing or servicing the appliance.

• The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.

• Use new hoses when connecting the appliance to the water supply. Do not reuse old hoses.

OPERATION

• Read all instructions before using the appliance and save these instructions.

• Use this appliance only for its intended purpose.

• If the product has been submerged, contact an LG Electronics customer information center for instructions

before resuming use.

• If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug it

immediately, and contact an LG Electronics customer information center.

• Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for

such a period, before using the appliance turn on all hot water faucets and let the water ow from each for

several minutes. This will release any accumulated hydrogen gas. As the gas is ammable, do not smoke or

use an open ame during this time.

• Do not reach into the washer if the tub or drum, agitator, or any interior parts are moving. Before loading,

unloading, or adding items, press Start/Pause and allow the tub or drum to coast to a complete stop before

reaching inside.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

• Do not allow children or pets to play on, in or with the appliance. Close supervision is necessary when the

appliance is used near children or pets.

• Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on product

labels.

• Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not use

a cord that shows cracks or abrasion damage along its length or at either end.

• Never unplug the appliance by pulling on the power cord. Always grip the plug rmly and pull straight out

from the outlet.

• Do not use an extension cord or adapter with this appliance.

• Do not grasp the power cord or touch the appliance controls with wet hands.

• Do not modify or extend the power cord.

5SAFETY INSTRUCTIONS

ENGLISH

• If the electrical supply cord is damaged, it must only be replaced by the manufacturer or its service agent or

a similar qualied person in order to avoid a hazard.

• Do not put oily or greasy clothing, candles or ammable materials on top of the appliance.

• Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags, etc.),

gasoline, chemicals and other ammable vapors and liquids.

• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other

appliance.

• Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when using

laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.

• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the nish.

• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, vegetable or cooking oil, or other ammable or explosive substances, as they give off

vapors that could ignite or explode.

• Do not add gasoline, dry cleaning solvents, or other ammable or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

• In the event of a gas leak (propane gas, LP gas, etc.) do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

• Do not tamper with controls.

• Fix the drain hose securely in place to avoid ooding.

• Do not abuse, sit on, or stand on the door of the appliance.

• Do not allow water, bleach or other liquids to sit in the drum for extended periods. Doing so can corrode the

drum or cause mildew or odors.

MAINTENANCE

• Do not repair or replace any part of the appliance. All repairs and servicing must be performed by qualied

service personnel unless specically recommended in this owner’s manual. Use only authorized factory

parts.

• Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply.

• Remove any dust or foreign matter from the power plug pins.

• Do not disassemble or repair the appliance by yourself.

• Remove the door before the appliance is removed from service or discarded to avoid the danger of children

or small animals getting trapped inside.

• Make sure the dispenser drawer or lid is closed at all times when not being lled with laundry products.

GROUNDING INSTRUCTIONS

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with

a qualied electrician or service personnel if you are in doubt whether the appliance is properly grounded.

Do not modify the plug provided with the appliance; if it will not t the outlet, have a proper outlet installed by

a qualied electrician.

• The appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance for electric current. The appliance is equipped with

a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an

appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

6 SAFETY INSTRUCTIONS

CAUTION

To reduce the risk of minor or moderate injury to persons, malfunction, or damage

to the product or property when using this product, follow basic precautions,

including the following:

INSTALLATION

• Install the product on a rm and level oor.

OPERATION

• Do not place objects on top of the appliance.

• Turn off the water faucets and unplug the appliance if the appliance is to be left for an extended period of

time, such as during vacations.

• ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

• Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

• Do not combine laundry products for use in one load unless specified on the label.

• Do not touch draining water which may be hot.

• If the drain hose and the water supply hose are frozen in winter, defrost them before using the appliance.

• Do not store or spill liquid detergents, cleaners, or bleaches (chlorine bleach, oxygen bleach) on the

appliance. Doing so may result in corrosion, discoloration or damage to the surface of the appliance.

• Clothing or articles that are waterproof or water resistant must be washed in the Waterproof cycle only.

(e.g. water resistant clothing, mattress covers, outdoor clothes, plastic mats, etc.) Using a different cycle

may result in personal injury or damage to the washer, clothes, walls, floor, and surrounding objects due

to abnormal vibration.

SAVE THESE INSTRUCTIONS

7PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Parts

12

13

1

Control Panel

4

Drum

7

Drain Pump Filter Cover

10

Water Inlets

2

Detergent Dispenser

Drawer

5

Door

8

Drain Pump Filter

11

Shipping Bolts

3

Door Seal

6

Leveling Feet

9

Drain Hose

12

Power Cord

13

Drain Hose

Accessories

Included Accessories

Non-skid pads

Hole caps (4)

Wrench

Tie strap

Elbow bracket

(for securing drain

hose)

Required Accessories

Hot/cold water hoses

(sold separately)

Optional Accessories

Pedestal or Pedestal washer

(sold separately)

Stacking Kit

(sold separately)

NOTE

• The images in this guide may be different from the actual components and accessories, which are subject to

change by the manufacturer without prior notice for product improvement purposes.

• For your safety and for extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction or accidents caused by the use of separately purchased unauthorized

components or parts.

8 INSTALLATION

INSTALLATION

Tools Needed

Pliers

Level

Installation Overview

Please read the following installation instructions rst after purchasing this product or transporting it to another

location.

TEST!

Choosing the proper location

Unpacking and removing

shipping bolts

Connecting the water lines

Connecting the drain line

Leveling the washer Connecting to the power

supply

Testing the washer

9INSTALLATION

ENGLISH

Product Specications

The appearance and specications listed in this manual may vary due to constant product improvements.

Electrical requirements 120 VAC @ 60 Hz

Min. / Max. water pressure 20 – 120 psi (138–827 kPa)

Dimensions

Net weight 187.4 lb (85 kg)

Max spin speed 1300 RPM

WARNING

• Moving or installation of the appliance requires two or more people. Failure to follow these instructions may

result in injury.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious injury,

re, electric shock, or death.

• Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this

warning can cause serious injury, re, electric shock, or death.

• To reduce the risk of electric shock, do not install the appliance in humid spaces. Failure to follow this

warning can cause serious injury, re, electric shock, or death.

• To ensure proper airow, do not block the large opening on the bottom of the washer with carpeting or other

materials.

• Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong

outlet. Failure to follow this warning can cause serious injury, re, electric shock, or death.

• Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing. Service personnel - Do not contact the following parts while the appliance is energized: pump,

valve, motor, control board.

70 cm (W) X 77 cm (D) X 99 cm (H), 139.6 cm (D with door open)

27”

(W) X 30 ¼” (D) X 39” (H), 55” (D with door open)

10 INSTALLATION

Choosing the Proper

Location

Install the washer on a solid oor that is strong and

rigid enough to support the weight of the washer,

even when fully loaded, without exing or bouncing.

If the oor has too much ex, you may need to

reinforce it to make it more rigid. If the oor is not

solid, it may cause severe vibration and noise.

NOTE

• Before installing the washer, make sure the oor

is clean, dry and free of dust, dirt, water and oil so

the washer feet cannot slide easily. Leveling feet

that can move or slide on the oor can contribute to

excess vibration and noise due to poor contact with

the oor.

• If a drip pan must be used, take extra care to follow

the instructions provided with the drip pan and make

sure the leveling feet are adjusted for rm and even

contact with the pan. Use of drip pans and failure to

properly level the machine may result in increased

vibration and noise during operation.

• Allow for sufcient space between the walls and the

washer for installation.

Power Outlet

• The power outlet must be within 60 inches (1.5 m)

of either side of the washer.

• The appliance and outlet must be positioned so that

the plug is easily accessible.

• Do not overload the outlet with more than one

appliance.

• The outlet must be grounded in accordance with

current electrical wiring codes and regulations.

• Use a time-delay fuse or circuit breaker.

NOTE

• It is the personal responsibility and obligation of the

product owner to have a proper outlet installed by

qualied service personnel.

Flooring

• To minimize noise and vibration, the washer must

be installed on a solidly constructed oor.

• Allowable slope under the entire washer is a

maximum 1 inch (2.5 cm) difference from side to

side or from front to back.

• Installing on carpeting and soft tile surfaces is not

recommended.

• Never install the washer on a platform or weakly

supported structure.

NOTE

• The washer must be installed on rm ooring to

minimize vibration during the spin cycle. Concrete

ooring is best, but a wood oor is sufcient,

provided it is built to FHA standards.

Floor Installation

(70 cm)(2.5 cm) (2.5 cm)

27"

1" 1"

(0.5 cm

)

13

64

4"

(10 cm)

(62.6

cm)

(77 cm)

55"

(139.6 cm)

24

¾

30

¼

To ensure sufcient clearance for water lines, the

drain line and airow, allow minimum clearances of at

least 1 inch (2.5 cm) at the sides and 4 inches

(10 cm) behind the unit. Be sure to allow for wall,

door, or oor moldings that may increase the required

clearances.

Stacked or Pedestal Installation

30 ¼"

(77 cm)

4"

(10 cm)

27"

(70 cm)

1"

(2.5 cm)

1"

(2.5 cm)

77 ½"

(196.8 cm)

(0.5 cm)

13

64

NOTE

• Refer to the instructions packaged with the optional

pedestal kit before installing with a pedestal kit.

• Do not use a drip pan with a pedestal or pedestal

washer installation as it can block the drawer. Using

a drip pan may result in increased vibration and

noise during operation.

11INSTALLATION

ENGLISH

Unpacking and Removing

Shipping Bolts

Remove all shipping materials from the washer for

proper operation and inspect it for shipping damage.

CAUTION

• Failure to remove shipping materials can cause

excessive noise and vibration.

1

Lift the washer off the foam base.

After removing the carton and shipping material,

lift the washer off the foam base. Make sure the

plastic tub support comes off with the base and is

not stuck to the bottom of the washer.

If you must lay the washer down to remove the

base packaging materials, always protect the side

of the washer and lay it carefully on its side. Do

not lay the washer on its front or back.

Foam tub

support

Carton base

2

Remove the bolt assemblies.

Starting with the bottom two shipping bolts, use

the wrench (included) to fully loosen all four

shipping bolts by turning them counterclockwise.

Remove the bolt assemblies by wiggling them

slightly while pulling them out.

Retainer

Shipping

bolt

3

Install the hole caps.

Locate the four hole caps included in the

accessory pack and install them in the shipping

bolt holes.

Cap

NOTE

• Save the bolt assemblies for future use. To prevent

damage to internal components, do not transport

the washer without reinstalling the shipping bolts.

• Failure to remove shipping bolts and retainers may

cause severe vibration and noise, which can lead

to permanent damage to the washer. The cord is

secured to the back of the washer with a shipping

bolt to help prevent operation with shipping bolts in

place.

12 INSTALLATION

Connecting the Water Lines

To avoid the risk of costly water damage, purchase

and install new inlet hoses when installing the

washer.

1

Check the ttings and seals.

Inspect the threaded tting on each hose and

make sure there is a rubber seal in place in both

ends of each hose to prevent leaking.

Rubber seal Rubber seal

Water hose (to water

inlet on washer)

Water hose (to tap)

2

Connect the water supply hoses.

Connect the water supply hoses to the hot and

cold water faucets tightly by hand and then

tighten another 2/3 turn with pliers. Connect the

blue hose to a cold water faucet and the red hose

to a hot water faucet.

3

Flush out the inlet hoses.

After connecting the inlet hoses to the water

faucets, turn on the water faucets to ush out

foreign substances (dirt, sand or sawdust) in the

water lines. Let water drain into a bucket, and

check the water temperature to make sure you've

connected the hoses to the correct faucets.

4

Attach the water lines to the back of the

washer.

Attach the hot water line to the hot water inlet on

the back of the washer. Attach the cold water line

to the cold water inlet on the back of the washer.

Tighten the ttings securely. Turn ON both faucets

all the way and check for leaks at both ends of the

hoses.

Cold

water

inlet

Hot water

inlet

WARNING

• Do not overtighten the hoses or cross-thread the

hose ttings. Overtightening or cross-threading

can damage the valves or couplings, resulting in

leaking and property damage.

• Do not reuse old hoses. Use only new hoses

when installing the washer. Old hoses could leak

or burst causing ooding and property damage.

Contact an LG Customer Information Center for

assistance in buying hoses.

NOTE

• Periodically check the hoses for cracks, leaks, and

wear, and replace the hoses every ve years. Do

not stretch the water hoses intentionally, and make

sure that they are not pinched, crushed or kinked by

other objects.

• Water supply pressure must be between 20 psi

and 120 psi (138 – 827 kPa). If the water supply

pressure is more than 120 psi, a pressure reducing

valve must be installed.

• To provide optimum washing performance, the hot

water temperature should be set at 120 – 130 °F

(48 – 54 °C) and the cold at 60 °F (15 °C).

• The washer should never be installed or stored in a

location subject to freezing temperatures. Damage

to the water lines and internal mechanisms of the

washer can result. If the washer was exposed to

freezing temperatures prior to installation, allow it to

stand at room temperature for several hours before

use and check for leaks prior to operation.

• Do not use ood-preventing hoses with auto shutoff

devices. The devices can be tripped during ll and

prevent the machine from lling properly.

13INSTALLATION

ENGLISH

Connecting the Drain Hose

Connect the drain hose to either a standpipe or

laundry tub.

NOTE

• The drain hose should always be properly secured.

Failure to properly secure the drain hose can result

in ooding and property damage.

• The drain must be installed in accordance with any

applicable local codes and regulations.

• Make sure that the drain hose is not stretched,

pinched, crushed, or kinked.

• Do not install the drain hose with the end lower than

29.5 inches (0.7 m) or higher than 96 inches

(2.4 m) above the bottom of the washer or more

than 60 inches (1.5 m) away from the washer.

• Never create an airtight seal between the hose and

the drain with tape or other means. If no air gap

is present, water can be siphoned out of the tub

resulting in poor wash/rinse performance or clothing

damage.

Option 1: Standpipe

1

Clip the end of the hose into the elbow

bracket.

Connect the elbow bracket within 4 inches

(10 cm) of the end of the drain hose. If the drain

hose is extended more than 4 inches (10 cm)

beyond the end of the elbow bracket, mold or

microorganisms could spread to the inside of the

washer.

No more than

4 inches (10 cm)

Elbow bracket

2

Insert the end of the drain hose into the

standpipe.

Drain hose

Elbow bracket

3

Use a tie strap to secure the drain hose in

place.

Option 2: Laundry Tub

1

Clip the end of the hose into the elbow

bracket.

Connect the elbow bracket within 4 inches

(10 cm) of the end of the drain hose. If the drain

hose is extended more than 4 inches (10 cm)

beyond the end of the elbow bracket, mold or

microorganisms could spread to the inside of the

washer.

No more than

4 inches (10 cm)

Elbow bracket

2

Hang the end of the drain hose over the side

of the laundry tub.

Drain hose

Elbow bracket

3

Use a tie strap to secure the drain hose in

place.

14 INSTALLATION

Leveling the Washer

The drum of your new washer spins at very high

speeds. To minimize vibration, noise, and unwanted

movement, the oor must be a level, solid surface.

NOTE

• Adjust the leveling feet only as far as necessary to

level the washer. Extending the leveling feet more

than necessary can cause the washer to vibrate.

• Before installing the washer, make sure that the

oor is clean, dry and free of dust, dirt, water and

oil so the washer feet cannot slide easily. Feet

that move or slide on the oor can contribute to

excessive vibration and noise due to poor contact

with the oor.

1

Position the washer in its nal location.

Take special care not to pinch, strain, or crush the

water and drain lines. If you have a carpenter's

level, you can place it across the top of the

washer. The slope beneath the washer should not

exceed 1 inch, and all four leveling feet must rest

rmly on the oor.

Level

1"

2

Adjust the lower nut on the leveling feet.

Turn in one direction to raise the washer or the

other direction to lower it.

Raise Lower

3

Tighten the locknuts.

Turn the locknuts counter-clockwise to tighten

them when the washer is level.

Locknut

Tighten all 4

locknuts securely

4

Recheck the washer’s levelness.

Push or rock the top edges of the washer gently

to make sure the washer does not rock. If the

washer rocks, repeat steps 2-3.

CAUTION

• Using the washer without leveling it may cause

excess vibration and noise, leading to a machine

malfunction.

• Extend the leveling feet only to level the washer.

If you extend the leveling feet unnecessarily, it

may cause abnormal vibration of the washer.

Using Non-Skid Pads

If you install the washer on a slippery surface, it may

move because of vibration. Incorrect leveling may

cause malfunction through noise and vibration. If this

occurs, install the non-skid pads under the leveling

feet and adjust the level.

1

Clean the oor to attach the non-skid pads.

Use a dry rag to remove and clean foreign objects

or moisture. If moisture remains, the non-skid

pads may slip.

2

Adjust the level after placing the washer in the

installation area.

3

Place the adhesive side of the non-skid pad

on the oor.

It is most effective to install the non-skid pads

under the front leveling feet. If it is hard to place

the pads under the front leveling feet, place them

under the back leveling feet.

This side up

Adhesive

side

Remove backing

4

Recheck the washer’s levelness.

Push or rock the top edges of the washer gently

to make sure that the washer does not rock. If the

washer rocks, level the washer again.

15INSTALLATION

ENGLISH

Connecting to the Power

Supply

The washer should be plugged into a 120-VAC,

60 Hz grounded 3-prong outlet. Plug in the washer.

WARNING

• Do not use a worn or damaged power cord or

power plug. Replace or repair it immediately.

Failure to do so may result in death, re, electric

shock, or malfunction.

• Do not modify the power cord and plug provided

with the appliance. Take care not to damage it

when installing or moving the washer. Failure

to follow this warning may result in death, re,

electric shock, or malfunction.

• Make sure that the washer is grounded.

• Connect this washer to a grounded outlet

conforming to the rating prior to use. Failure

to do so may result in re, electric shock, or

malfunction.

• Do not damage or cut off the ground prong of

the power cord. Doing so may cause death, re,

electric shock, or product malfunction.

• Improper connection of the equipment-grounding

conductor can result in risk of electric shock.

Check with a qualied electrician or service

technician if you are in doubt as to whether the

appliance is properly grounded. If it does not t

the outlet, have a proper outlet installed by a

qualied electrician

• The appliance and outlet must be positioned so

that the plug is easily accessible.

• Do not use adapters or extension cords. Doing

so may result in serious injury, re, electric

shock, or death.

• For best performance, plug the washer into

its own individual outlet. This helps prevent

overloading house wiring circuits which could

cause a re hazard from overheated wires.

• If necessary, use a new, UL-listed 3-prong

adapter or 3-wire extension cord with a 3-prong

(grounding) plug rated at no less than the branch

circuit. Do not use an extension cord longer

than 3 feet. Failure to follow these warnings may

result in serious injury, re, electric shock, or

death.

Testing the Washer

Check if the washer is properly installed and run a

test cycle.

1

Load the washer with 6 pounds of laundry

(approximately 6 thick bath towels).

2

Press the Power button.

3

Press the Rinse+Spin button.

4

Press the Start/Pause button.

The wash cycle starts.

5

Check if water is supplied, that the machine does

not rock or vibrate excessively, and that it drains

well during the spin cycle.

NOTE

• If water leaks during water supply, see Connecting

the Water Lines to connect them properly.

• If the washer rocks and vibrates excessively, see

Leveling the Washer to level it again.

• If the drain does not work, see Connecting the Drain

Hose to install the hose properly.

16 OPERATION

OPERATION

Using the Washer

WARNING

• To reduce the risk of re, electric shock, or injury to persons, read the SAFETY INSTRUCTIONS before

operating this appliance.

1

Sort Laundry and Load the Washer

Sort laundry by fabric type, soil level, color and load size, as needed. Open the

door and load items into the washer.

If using single-use detergent packs, place pack in drum before loading

laundry.

2

Add Cleaning Products.

Add the proper amount of HE (High-Efciency) detergent to the detergent

dispenser. If desired, add bleach or fabric softener to the appropriate areas

of the dispenser drawer. Do not place liquid or powdered detergent packs in

the dispenser.

3

Turn on the Washer

Press the Power button to turn on the washer. The lights above the cycle

buttons will illuminate and a chime will sound.

4

Select a Cycle

Turn the Cycle Selector Knob until the desired cycle is selected. The preset

Temp., Spin, Soil and option settings for that cycle will be shown. Pressing the

Start/Pause button without selecting a cycle will cause the Normal cycle to

begin immediately with the default settings.

5

Adjust Settings

Default settings for the selected cycle can now be changed, if desired, using the

cycle modier and option buttons.

• Not all modiers and options are available on all cycles. A different chime will

sound and the LED will not come on if the selection is not allowed.

6

Begin Cycle

Press the Start/Pause button to begin the cycle. The washer will agitate briey

without water to measure the weight of the load. If the Start/Pause button is

not pressed within a certain time, the washer will shut off and all settings will be

lost.

7

End of Cycle

When the cycle is nished, a melody will sound. Immediately remove your

clothing from the washer to reduce wrinkling. Check around the door seal when

removing the load for small items that may be caught in the seal.

NOTE

• The washer rotates the laundry in a way that allows it to use less water while still fully saturating your clothing.

It is normal to not be able to see water during the wash cycle.

• If the temperature or the water level inside the machine is too high, the door will not unlock when the Start/

Pause button is pressed. To stop a cycle and drain the water completely, turn the power off, then on, and then

press Rinse+Spin.

OPERATION_WM3400CW 17

ENGLISH

Sorting Laundry

CAUTION

• The washer can be fully loaded, but the drum

should not be tightly packed with items. The door

of the washer should close easily.

• Use the Bedding cycle for buoyant or

nonabsorbent items such as pillows or

comforters. Failure to follow this caution can

result in leakage.

• Clothing or articles that are waterproof or water

resistant must be washed in the Bedding cycle

only. (e.g. water resistant clothing, mattress

covers, outdoor clothes, plastic mats, etc.)

Otherwise, it may result in personal injury or

damage to the washer, clothes, walls, oor, and

surrounding objects due to abnormal vibration.

• Remove the stufng from pillows and cushions

before washing the covers. Failure to do so can

cause excessive vibration, resulting in damage

to the washer, clothes, nearby objects, walls, and

oor.

Grouping Similar Items

For the best washing results, and to reduce the

possibility of damage to clothing, care should be

taken to sort the clothing into loads that are made up

of similar items.

Mixing different fabric types and/or soil levels can

result in poor wash performance, color transfer,

discoloration, fabric damage or linting. Fabrics should

be sorted into groups as described below.

Colors

Sort articles by color. Wash dark clothes together in a

separate load from light colors or whites. Mixing dark

clothes with light clothes can result in dye transfer or

discoloration of the lighter clothes.

Soil Level

Wash heavily soiled clothing together. Washing lightly

soiled clothing in the same load with heavily soiled

clothing could result in poor wash performance for

the lightly soiled clothing.

Fabric Type

Delicate articles should not be mixed with heavy

or sturdy fabric types. Washing heavy fabrics in a

delicate load can result in poor wash performance

for the heavy fabrics and possible damage to the

delicates.

Lint Type

Some fabrics attract and bind lint to them while others

give off lint in the laundry process. Avoid mixing these

lint collectors and lint producers in the same load.

Mixing these fabrics will result in pilling and linting on

the lint collectors. (For example, lint collector—knit

sweater; lint producer—terry cloth towels.)

Sort Laundry

By colors By Soil By Fabric By Lint

White Heavy Delicates

Lint

Producer

Lights Normal Easy Care

Lint

Collector

Darks Light Sturdy

Fabric Care Labels

Many articles of clothing include a fabric care label.

Using the chart below, adjust the cycle and option

selections to care for your clothing according to the

manufacturer’s recommendations.

Category Label Directions

Washing

Hand wash

Machine wash, Normal

cycle

Perm Press/Wrinkle

Resistant setting (which has

a cool down or cold spray

before the slower spin)

Gentle/Delicate setting

(slow agitation and/or

reduced wash time)

Do not wash

Do not wring

Water

Temperature

Hot

Tepid

Cold/Cool

Bleach

Symbols

Any bleach (when needed)

Only non-chlorine bleach

(when needed)

Do not bleach

18 OPERATION_WM3400CW

Loading the Washer

• Check and empty pockets. Paper clips, coins,

matches, etc. can damage clothing and the washer.

• Close zippers and hooks, and tie drawstrings to

prevent snagging or tangling of clothes.

• Pretreat heavily stained areas for best results.

• Combine large and small items in a load. Load large

items rst. Large items should not be more than half

of total load.

• The washer can be fully loaded, but the drum

should not be tightly packed with items. The door of

the washer must close easily.

• Do not wash single small items. Add 1-2 similar

items to the load to prevent an out-of-balance load.

• Wash thick, bulky items individually. Heavy blankets,

comforters, bedspreads, or pet beds can get

tangled or cause an unbalanced load if combined

with other items.

• Do not wash/spin waterproof items. Washing

raincoats or sleeping bags may result in abnormal

vibration or may cause the load to bounce, which

could damage the drum.

• Wash small, light items in a mesh bag. Items like

underwear can get caught in the door seal, and

a brassiere hook may damage other items or the

drum.

• Brush off heavy soil, dust, and hair from items

before washing. Excess dirt or sand can abrade

other fabrics and lead to poor wash performance.

• For best performance, load clothes as shown.

1

3

2

4

- Load clothes loosely, and do not overll the drum.

Clothes need room to circulate in order to get

clean.

- Do not press down on items while stacking them in

the drum.

Adding Cleaning Products

Loading the Dispenser

To add detergent, bleach, and fabric softener to the

automatic dispenser.

1

Open the detergent dispenser drawer.

2

Load the laundry products into the

appropriate compartments.

• If using a liquid detergent, make sure the liquid

detergent cup is in place.

• If using a powdered detergent, remove the liquid

detergent cup and put the powder in the main

wash detergent compartment.

• If using detergent pods, place the pod in the

drum before loading the laundry. Do not place

liquid or powdered detergent pods in the

dispenser.

Pre-washPre-wash

detergentdetergent

compartmentcompartment

Liquid Liquid

detergent detergent

cupcup

Liquid chlorine Liquid chlorine

bleach bleach

compartmentcompartment

Main wash Main wash

detergent detergent

compartmentcompartment

Liquid fabric Liquid fabric

softener softener

compartmentcompartment

3

Close the detergent dispenser drawer slowly

before starting the cycle.

• Slamming the detergent dispenser drawer may

result in the detergent overowing into another

compartment or pouring into the tub earlier than

programmed.

NOTE

• It is normal for a small amount of water to remain in

the dispenser compartments at the end of the cycle.

ENGLISH

IMPORTANT:

• Do not place or store laundry products, such as

detergent, bleach, or liquid fabric softener, on

top of your washer or dryer. Wipe up any spills

immediately. These products can damage the

machine's nish and controls.

Pre-Wash Detergent Compartment

Add liquid or powdered detergent to this compartment

when using the Pre-Wash option. Always use HE

(High-Efciency) detergent with your washer.

• When using the Pre-Wash option, liquid detergent

for the main wash needs to be loaded in the

liquid detergent cup accessory in the main wash

dispenser, to prevent it from being dispensed with

the pre-wash detergent.

• The amount of detergent added for the Pre-Wash

option is 1/2 the amount recommended for the

main wash cycle. For example, if the main wash

cycle requires one measure of detergent, add 1/2

measure for the Pre-Wash option.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the

main wash cycle. Either powdered or liquid detergent

may be used in this compartment. The detergent

is added to the load at the beginning of the cycle.

Always use HE (High-Efciency) detergent with your

washer.

NOTE

• Never exceed the manufacturer’s recommendations

when adding detergent. Using too much detergent

can result in detergent buildup in clothing and the

washer.

• Liquid or powdered color-safe bleach may be added

to the main wash compartment with detergent of the

same type.

• When using liquid detergent, make sure the liquid

detergent cup and insert are in place. Do not

exceed the maximum ll line.

• When using powdered detergent, remove the insert

and liquid detergent cup from the compartment.

Powdered detergent will not dispense with the liquid

detergent cup and insert in place.

• If you use a detergent that does not dissolve easily

or a detergent with high viscosity, it will leave a

residue and may clog on the dispenser.

OPERATION_WM3400CW 19

Liquid Bleach Compartment

This compartment holds liquid bleach, which is

dispensed automatically at the proper time during

the wash cycle. The dispenser is activated twice to

ensure complete dispensing of the bleach. Any liquid

remaining in the dispenser at the end of the cycle is

water, not bleach.

• Do not add powdered bleach to this compartment.

The bleach compartment is designed to dispense

liquid chlorine bleach only. Powdered or liquid color-

safe bleach will not dispense properly.

• Always follow the manufacturer's recommendations

when adding bleach. Never add more than one cup

and do not exceed the maximum ll line since this

can cause the bleach to be dispensed immediately,

resulting in damage to fabrics. Using too much

bleach can damage fabrics.

• Never pour undiluted liquid chlorine bleach directly

onto the load or into the drum. Fabric damage can

occur.

• Do not use color-safe bleach or Oxi products in the

same cycle with liquid chlorine bleach.

WARNING

• Do NOT mix chlorine bleach with ammonia or

acids such as vinegar or rust/scale remover.

Mixing chemicals like these can produce a lethal

gas, resulting in severe injury or death.

20 OPERATION_WM3400CW

Fabric Softener Compartment

This compartment holds liquid fabric softener, which

is automatically dispensed during the nal rinse cycle.

Do not exceed the manufacturer’s recommendations

when adding softener. Using too much fabric softener

can result in buildup in clothing and the washer.

Either powdered or liquid fabric softener may be

used.

• Follow the manufacturer’s recommendations when

adding fabric softener. Do not exceed the maximum

ll line. Using too much fabric softener may stain

clothes.

• Dilute concentrated fabric softeners with Tepid

water. Do not exceed the maximum ll line.

• Never pour fabric softener directly onto the load or

into the drum.

Detergent Use

This washer is designed for use with only HE (High-

Efciency) detergents. HE detergents produce fewer

suds, dissolve more efciently to improve washing

and rinsing performance, and help to keep the

interior of the washer clean. Using detergent that is

not HE may cause oversudsing and unsatisfactory

performance which could result in error codes, cycle

failure, and machine damage.

Designed specially to use only HE

(High-Efciency) detergent

• For proper wash performance, always measure

detergent using the measuring device provided by

the detergent manufacturer. For an average load,

use less than half of the recommended maximum.

Use less detergent for soft water, light soil, or

smaller loads.

• Never use more than the maximum amount of

detergent recommended by the manufacturer. Using

too much detergent can lead to oversudsing, poor

rinsing, detergent buildup in clothing, and residue

buildup that can contribute to odors in the machine.

• Use extra care when measuring 2X and 3X

concentrated detergents because even a small

amount extra can lead to problems.

• Detergents designated as HE-compatible may not

provide optimal results.

• Do not use more than one detergent pod in the

washer. Using too much detergent may cause

oversudsing and unsatisfactory performance.

Reduce detergent amount or add an extra rinse if

detergent residue is left on fabrics. To add an extra

rinse, press the Extra Rinse button.

Liquid Liquid

detergentdetergent

MaximumMaximum

Normal Load AmountNormal Load Amount

Powdered Powdered

detergentdetergent

Detergent Pods

Place liquid or powdered detergent pods in the drum

before loading laundry. Do not place pods in the

dispenser.

La page charge ...

LG 1177675 Manuel utilisateur

LG 1177675 Manuel utilisateur

dans d''autres langues

Documents connexes