TP-LINK LS1005G Guide d'installation
- Catégorie
- Commutateurs réseau
- Taper
- Guide d'installation
Ce manuel convient également à
© 2019 TP-Link
7106508315 REV1.0.0
Note: For simplicity, we will take LS1008G for example throughout this Guide.
Connection
PC
Router
LAN PortWAN Port
Internet
PC
Power Adapter
LS1008G
Ethernet Ports (1-8)Power LED
5/8-Port Gigabit Desktop Switch
Installation Guide
LS1005G/LS1008G
LED Explanation
Link/Act
Link/Act (Green)
On:
Running at 10/100/1000 Mbps
Flashing: Transmitting/receiving data
O:
No device is linked to the
corresponding port
On: Power on
O: Power o
Power
Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Environmental and Physical Specications
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
General Specications
Data Transfer Rate
Network Media (Cable)
IEEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x
CSMA/CD
Ethernet: 10 Mbps (Half Duplex), 20 Mbps (Full Duplex)
Fast Ethernet: 100 Mbps (Half Duplex), 200 Mbps (Full Duplex)
Gigabit Ethernet: 2000 Mbps (Full Duplex)
10Base-T: UTP category 3, 4, 5 cable (maximum 100 m)
EIA/TIA-568 100
Ω
STP (maximum 100 m)
100Base-TX: UTP category 5, 5e cable (maximum 100 m)
EIA/TIA-568 100
Ω
STP (maximum 100 m)
1000Base-T: UTP category 5e cable (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
5/8 10/100/1000 Mbps Auto-Negotiation RJ45 Ports
Power, Link/Act LED
Store-and-Forward
Automatically learning, automatically aging
10Base-T: 14881 pps/Port
100Base-TX: 148810 pps/Port
1000Base-T: 1488095 pps/Port
Standard
Protocol
Interface
LED Indicators
Transfer Method
MAC Address Learning
Frame Forward Rate
Wall Mountable
Distance Between
Mounting Holes
Ye s
LS1005G: 38 mm
LS1008G: 48 mm
Frequently Asked Questions (FAQ)
Q1. The Power LED is not lit.
The Power LED should be lit when the power system is
working normally. If the Power LED is not lit, check as
follows:
A1:
A2:
A3:
Make sure the power source is ON.
Make sure the power adapter is connected to the
switch with power source properly.
Make sure the voltage of the power supply meets the
requirements of the input voltage of the switch.
Q2. The Link/Act LED is not lit when a device
is connected to the corresponding port.
It is recommended that you check the following items:
A1:
A2:
Make sure that the cable connectors are rmly plugged
into the switch and the device.
A3:
The cable must be less than 100 meters long (328 feet).
Make sure the connected device is turned on and
works normally.
For technical support, and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides,
welcome to email techwriter@tp-link.com.cn.
To ask questions, find answers, and communicate with TP-Link
users or engineers, please visit
https://community.tp-link.com to joinTP-Link Community.
Q2. The Link/Act LED is not lit when a device
is connected to the corresponding port.
FCC compliance information statement
限用物質含有情況標示聲明書
限用物質及其化學符號
鉛
Pb
鎘
Cd
汞
Hg
六價鉻
CrVI
多溴聯苯
PBB
多溴二苯醚
PBDE
產品元件名稱
PCB
外殼
電源適配器
備考1. “ “系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2. “ “系指該項限用物質為排除項目。
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Explanation of the symbols on the product label
DC voltage
AC voltage
Class II equipment
Polarity of output terminals
Energy eciency marking
Indoor use only
RECYCLING
This product bears the selective sorting symbol for Waste
electrical and electronic equipment (WEEE). This means that this
product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or
electronic equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Consult the dealer or an experienced radio/ TV technician for help.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
Safety Information
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
Do not use any other chargers than those recommended.
Keep the device away from water, re, humidity or hot environments.
Do not use damaged charger or USB cable to charge the device.
Do not attempt to disassemble, repair, or modify the device.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
Note: The product label can be found at the bottom of the product.
Product Name: 5/8-Port Gigabit Desktop Switch
Model Number: LS1005G/LS1008G
Component Name Model
T050060-2B1 (For LS1005G)
T090060-2B1 (For LS1008G)
I.T.E. Power Supply
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
E-mail: [email protected]
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Consult the dealer or an experienced radio/ TV technician for help.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
To mount the device on a wall, use two screws which complies with ANSI B1.1 4#,
(5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are
xed on the wall, the distance between the screw head and the wall should be
more than 1.5 mm.
Product Name: I.T.E. Power Supply
Model Number: T050060-2B1/T090060-2B1
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
E-mail: [email protected]
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на
відповідність вимогам нормативних документів та вимогам, що передбачені
чинними законодавчими актами України.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Mark Warning
Canadian Compliance Statement
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU,
2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/ce.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Mounting Requirements
-
1
-
2
-
3
TP-LINK LS1005G Guide d'installation
- Catégorie
- Commutateurs réseau
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
- English: TP-LINK LS1005G Installation guide
Documents connexes
-
TP-LINK DECO S4 3-PACK AC1200 Le manuel du propriétaire
-
TP-LINK Deco M4 Mode d'emploi
-
-
TP-LINK TL-SG1008P Guide d'installation
-
TP-LINK Deco M5 Mode d'emploi
-
-
-
TP-LINK TG-3468 Mode d'emploi
-
-
TP-LINK Archer T2U Plus Le manuel du propriétaire