Aiwa AV-D57 Operating Instructions Manual

Printed in Malaysia

For assistance and information

call toll free 1-800-BUY-AIWA

(United States and Puerto Rico)

NOTE

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment into an outlet on circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Modifications or adjustments to this product, which are not

expressly approved by the manufacturer, may void the user’s

right or authority to operate this product.

STEREO RECEIVER

RECEPTOR ESTEREO

AMPLI-TUNER STEREO

U

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D’EMPLOI

En (English)

8A-AR3-903-01

000115ACK-Y-M

F (Français)

AV-D57

For assistance and information

call toll free 1-800-BUY-AIWA

(United States and Puerto Rico)

E (Español)

English

Note on the selection of the DOLBY SURROUND center speaker mode

When selecting the center speaker mode (NORMAL or WIDE) of the DOLBY SURROUND, first select the “DOLBY D” or

“PRO LOGIC” mode (not the “3 STEREO” mode) and then select the center speaker mode.

The selected center speaker mode for the DOLBY D or PRO LOGIC mode is also effective for the 3 STEREO mode.

Español

Nota sobre la selección del modo de altavoz central DOLBY SURROUND

Al seleccionar el modo de altavoz central (NORMAL o WIDE) de DOLBY SURROUND, seleccione primero el modo “DOLBY

D” o “PRO LOGIC” (y no el modo “3 STEREO”) y después elija el modo de altavoz central.

El modo de altavoz central seleccionado para el modo DOLBY D o PRO LOGIC también es efectivo para el 3 STEREO.

Français

Remarque sur la sélection du mode DOLBY SURROUND avec enceinte centrale

Lors de la sélection du mode d’enceinte centrale (NORMAL ou WIDE) de DOLBY SURROUND, sélectionnez d’abord le

mode “DOLBY D” ou “PRO LOGIC” (pas le mode “3 STEREO”) puis sélectionnez le mode d’enceinte centrale.

Le mode d’enceinte centrale sélectionné pour le mode DOLBY D ou PRO LOGIC fonctionne également avec le mode 3 STEREO.

Deutsch

Hinweis zur Auswahl des DOLBY SURROUND-Modus für den mittleren Lautsprecher

Wenn Sie den DOLBY SURROUND-Modus für den mittleren Lautsprecher einstellen (NORMAL oder WIDE), wählen Sie

erst “DOLBY D” oder “PRO LOGIC” (nicht “3 STEREO”) und dann den Modus für den mittleren Lautsprecher.

Der ausgewählte Modus (DOLBY D oder PRO LOGIC) für den mittleren Lautsprecher gilt auch für den Modus 3 STEREO.

Italiano

Nota sulla selezione del modo del diffusore centrale DOLBY SURROUND

Se si seleziona il modo del diffusore centrale (NORMAL o WIDE) di DOLBY SURROUND, selezionare per prima cosa il

modo “DOLBY D” o “PRO LOGIC” (non il modo “3 STEREO”), quindi selezionare il modo del diffusore centrale.

Il modo del diffusore centrale selezionato per il modo DOLBY D o PRO LOGIC èinoltre operativo per il modo 3 STEREO.

Nederlands

Opmerking over het kiezen van de DOLBY SURROUND middenluidsprekerstand

Bij het kiezen van de middenluidsprekerstand (NORMAL of WIDE) van DOLBY SURROUND, kiest u eerst de stand “DOLBY

D” of “PRO LOGIC” (niet de stand “3 STEREO”) en daarna de middenluidsprekerstand.

De middenluidsprekerstand die u heeft gekozen voor DOLBY D of PRO LOGIC geldt ook in de 3 STEREO stand.

Česky

Poznámka k volbě režimu prostředního reproduktoru DOLBY SURROUND

Při volbě režimu prostředního reproduktoru (NORMAL nebo WIDE) DOLBY SURROUND, zvolte nejprve režim “DOLBY D”

nebo “PRO LOGIC” (ne režim “3 STEREO”) a potom zvolte režim prostředního reproduktoru.

Zvolený režim prostředního reproduktoru pro režim DOLBY D nebo PRO LOGIC funguje také pro režim 3 STEREO.

Magyar

Megjegyzés a DOLBY SURROUND (körhangzás) középső hangsugárzó mód kiválasztásáról

Ha DOLBY SURROUND (körhangzás) üzemben a középső hangsugárzó módot (NORMAL (normál) vagy WIDE (széles))

kívánja kiválasztani, válassza először a “DOLBY D” vagy “PRO LOGIC” módot (ne a “3 STEREO”) módot, és ezután válassza

a középső hangsugárzó módot.

A DOLBY D vagy PRO LOGIC üzemmódra kiválasztott középső hangsugárzó mód a 3 STEREO üzemben is működik.

Polski

Uwaga dotycząca nastawiania DOLBY SURROUND na tryb środkowego głośnika

Nastawiając na tryb środkowego głośnika (NORMAL lub WIDE) dla DOLBY SURROUND, należy w pierwszej kolejności

nastawić tryb “DOLBY D” lub “PRO LOGIC” (nie nastawiać trybu “3 STEREO”) i następnie wybrać tryb głośnika środkowego.

Nastawienie trybu głośnika środkowego dla DOLBY D lub PRO LOGIC dotyczy również trybu 3 STEREO.

8A-AR2-920-01

0003ACK-Y-M

Printed in Malaysia

1

ENGLISH

Owner’s record

For your convenience, record the model number and serial

number (you will find them on the rear of your unit) in the space

provided below. Please refer to them when you contact your Aiwa

dealer in case of difficulty.

Model No. Serial No. (Lot No.)

AV-D57

ENGLISH

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

PRECAUTIONS

Read the Operating Instructions carefully and completely before

operating the unit. Be sure to keep the Operating Instructions

for future reference. All warnings and cautions in the Operating

Instructions and on the unit should be strictly followed, as well

as the safety suggestions below.

Installation

1 Water and moisture — Do not use this unit near water, such

as near a bathtub, washbowl, swimming pool, or the like.

2 Heat — Do not use this unit near heat sources, including

heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C

(41°F) or higher than 35°C (95°F).

3 Mounting surface — Place the unit on a flat, even surface.

4 Ventilation — The unit should be situated with adequate

space around it so that proper heat ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and the top of the

unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that

may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight

rack where ventilation may be impeded.

5 Objects and liquid entry — Take care that objects or liquids

do not get inside the unit through the ventilation openings.

6 Carts and stands — When placed or

mounted on a stand or cart, the unit

should be moved with care.

Quick stops, excessive force, and

uneven surfaces may cause the unit or

cart to overturn or fall.

7 Wall or ceiling mounting — The unit should not be mounted

on a wall or ceiling, unless specified in the Operating

Instructions.

Electric Power

1 Power sources — Connect this unit only to power sources

specified in the Operating Instructions, and as marked on

the unit.

2 Polarization — As a safety feature, some units are equipped

with polarized AC power plugs which can only be inserted

one way into a power outlet. If it is difficult or impossible to

insert the AC power plug into an outlet, turn the plug over

and try again. If it is not still inserted easily into the outlet,

please call a qualified service technician to service or replace

the outlet. To avoid defeating the safety feature of the polarized

plug, do not force it into a power outlet.

3 AC power cord

- When disconnecting the AC power cord, pull it out by the

AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this

could result in fire or shock.

- Power cords should be firmly secured to avoid being severely

bent, pinched, or walked upon. Pay particular attention to

the cord from the unit to the power socket.

- Avoid overloading AC outlets and extension cords beyond

their capacity, as this could result in fire or shock.

4 Extension cord — To help prevent electric shock, do not

use a polarized AC power plug with an extension cord,

receptacle, or other outlet unless the polarized plug can be

completely inserted to prevent exposure of the blades of the

plug.

5 When not in use — Unplug the AC power cord from the AC

power outlet if the unit will not be used for several months or

more. When the cord is plugged in, a small amount of current

continues to flow to the unit, even when the power is turned

off.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

“CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

EnEn

En

ENGLISH

2

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

Remote control

FM antenna AM antenna

Operating Instructions, etc.

Outdoor Antenna

1 Power lines — When connecting an outdoor antenna, make

sure it is located away from power lines.

2 Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected

voltage surges or static electricity build-up. Article 810 of the

National Electrical Code, ANSI/NFPA70, provides information

on proper grounding of the mast, supporting structure, and

the lead-in wire to the antenna discharge unit, as well as the

size of the grounding unit, connection to grounding terminals,

and requirements for grounding terminals themselves.

Maintenance

Clean the unit only as recommended in the Operating

Instructions.

Damage Requiring Service

Have the unit serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have gotten inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.

TABLE OF CONTENTS

PRECAUTIONS ...................................................................1

PREPARATIONS

CONNECTIONS ..................................................................3

BEFORE OPERATION........................................................7

SOUND

CUSTOM AUDIO ADJUSTMENT .......................................8

ELECTRONIC GRAPHIC EQUALIZER ..............................9

DSP SURROUND..............................................................10

BASIC OPERATIONS

SELECTION OF AUDIO/VIDEO SOURCE.......................11

RECORDING AN AUDIO SOURCE .................................12

RADIO RECEPTION

MANUAL TUNING .............................................................13

PRESETTING STATIONS .................................................14

DOLBY SURROUND

SELECTING DOLBY SURROUND...................................15

ADJUSTING SPEAKER LEVEL BALANCE ....................16

ADJUSTING DOLBY DIGITAL SURROUND SOUND.....18

TIMER

SETTING THE CLOCK......................................................19

SETTING THE SLEEP TIMER .......................................... 19

GENERAL

SPECIFICATIONS ............................................................. 20

CARE AND MAINTENANCE ............................................21

TROUBLESHOOTING GUIDE ..........................................21

PARTS INDEX ...................................................................21

Check your accessories

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE

UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC-NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND CLAMP

Antenna Grounding According to the National Electrical Code

3

ENGLISH

CONNECTING EQUIPMENT

Jacks and plugs of the connecting cord are color-coded as

follows:

Red jacks and plugs : For the right channel of audio signals

White jacks and plugs: For the left channel of audio signals

Yellow jacks and plugs: For video signals

NOTE

Insert the plugs fully into the jacks. Loose connections may

produce a humming sound or other noise interference.

CONNECTIONS

Before connecting the AC cord

The rated voltage of your unit shown on the rear panel is 120 V

AC. Check that the rated voltage matches your local voltage.

IMPORTANT

Connect the speakers, antennas, and all other external

equipment first. Then connect the AC cord at the end.

PREPARATIONS

*

1

Be sure to connect the VIDEO OUT terminal of a DVD player

directly to a TV set, not through this unit. Otherwise, the picture

noise may appear when playing copy protected DVDs.

*

2

Input sound through the DIGITAL IN terminals cannot be

recorded. When recording the sound from the DVD, CD, MD

or LD player, connect the analog AUDIO OUT terminals of the

player to the corresponding AUDIO IN terminals of the receiver.

*

3

When connecting a monaural video, use a stereo-mono

connecting cord (not supplied).

*

4

When connecting an LD player equipped with the AC-3 RF

OUT terminal, use an RF demodulator unit. Also connect the

analog AUDIO OUT terminals of the LD player to the receiver

to play all the sources. For further information, refer to the

instructions of the LD player.

TV

Video 2* or

LD* /Cable TV

DVD or Video 1* /MD player

to VIDEO IN(Video 1)

to AUDIO IN(Video 1/MD)

to VIDEO IN

to AUDIO OUTPUT

to AUDIO OUT

to COAXIAL

DIGITAL OUT

Coaxial connecting

cord

Optical

connecting

cord

to OPTICAL

DIGITAL OUT

(DVD)

to AUDIO IN (Video 2)

to VIDEO OUT

to VIDEO IN (Video 2)

3

4

RF demodulator*

4

3

CD player

Turntable

Tape deck

to OUTPUT

to LINE OUT

to LINE IN

to VIDEO OUT(Video 1)*

to AUDIO OUT

1

*

2

*

2

REAR

FRONT

Camcorder

to VIDEO OUT

to AUDIO OUT

o

EnEn

En

ENGLISH

4

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

CONNECTING SPEAKERS1

Speaker terminals

Connect front speakers (system A and/or B), a center speaker,

surround speakers and sub woofer to the corresponding speaker

terminals on the unit:

- the front speaker cords to the FRONT SPEAKERS terminals

- the center speaker cord to the CENTER SPEAKER terminals

- the surround speaker cords to the SURROUND SPEAKERS

terminals.

- for more powerful bass, the sub woofer (with a built-in amplifier)

cord to the SUB WOOFER 3 jack

When connecting the sub woofer, be sure to select the

“SUBW ON” (sub woofer on) mode (see page 5).

Speaker impedance

For all speakers, use speakers of 8 ohms or more.

Connecting + to +, – to – terminals

To get the proper sound effect, the speaker terminals on the unit

and the speaker should be connected with proper polarity; the +

terminal on the unit should be connected to the + terminal on

the speaker (and – to –).

NOTE

• Be sure to connect the speaker cords correctly as shown in

the illustration on the right column. Improper connections can

cause short circuits in the SPEAKER(S) terminals.

• Do not leave objects generating magnetism near the speakers.

PREPARATIONS

Sub woofer

Surround speakers

Front speakers

Center speaker

1 and 2 in the illustration correspond to the following details.

Lift up the terminal flap,

insert the speaker cord lead

into the terminal slot, then

close the flap. Check that the

cord is connected securely.

1

Speaker system B

Right Left

1

Speaker system A

Right Left

1

Surround speakers

Right Left

1

Center speaker

1

Sub woofer

2

FM antenna

2

AM antenna

5

ENGLISH

CONNECTING THE SUPPLIED ANTENNAS 2

Connect the FM antenna to the FM 75 Ω terminals and the AM

antenna to the AM LOOP terminals.

To stand the AM loop antenna on a surface

Fix the claw to the slot as shown in the illustration.

To position the antennas

FM feeder antenna:

Extend this antenna horizontally in a T shape and fix its ends to

the wall.

AM loop antenna:

Position for the best reception.

NOTE

• Do not bring the FM antenna near metal objects or curtain rails.

• Do not bring the AM antenna near other external equipment,

the unit itself, the AC power cord or speaker cords, as noise

will be picked up.

• Do not unwind the AM loop antenna wire.

CONNECTING AN OUTDOOR ANTENNA

For better FM reception, use of an outdoor antenna is

recommended. Connect the outdoor antenna to the FM 75 Ω

terminals.

POSITIONING THE SPEAKERS

Position the speakers to make the most of DOLBY SURROUND

or DSP effect.

Front speakers (L/R)

Center speaker (C)

Position in the center of the two front speakers. In addition,

position on or below the TV set, if connecting a TV set to the

unit.

Surround speakers (SL/SR)

Place the surround speakers directly to the side of or slightly

behind the listening area. Align them horizontally, about 1 meter

(3.2 feet) above ear height.

Sub woofer (SW)

Place the sub woofer in any place between the two front speakers.

When connecting a sub woofer

Select “SUBW ON” mode.

1. Press the MANUAL SELECT button on the remote control

once so that “SUBW OFF” appears on the display.

2. Within 4 seconds, press the TUNING M button or turn

the MULTI JOG to the left to display “SUBW ON.”

If a sub woofer is not connected, be sure to select “SUBW

OFF.”

Display “SUBW ON” in step 1 and press the TUNING N

button or turn the MULTI JOG to the right in step 2.

NOTE

Sound from the surround speakers or center speaker depends

on the setting of DOLBY SURROUND or DSP surround.

FM antenna

AM antenna

EnEn

En

ENGLISH

6

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

PREPARATIONS

ABOUT THE REMOTE CONTROL

Inserting batteries

Detach the battery cover on the rear of the remote control and

insert two R6 (size AA) batteries.

When to replace the batteries

The maximum operational distance between the remote control

and the sensor on the unit should be approximately 5 meters

(16 feet). When this distance decreases, replace the batteries

with new ones.

Using the remote control

The instructions in this manual refer mainly to the buttons on the

main unit.

Some buttons have two functions.

• To use the function indicated on the button, or on the plate in

black, simply press the button.

• To use the function indicated on the plate in green, press the

button while pressing the SHIFT button.

Important

• The ENTER button on the remote control does not

substitute for the ENTER button on the main unit. This

button is for operating the DVD player only (see right

column.)

• In principal, the TUNING UP and DOWN buttons on the

remote control substitute for N and M buttons on

the main unit. Press the button while pressing the SHIFT

button.

To select the function (audio source) with the remote

control

Press the FUNCTION button repeatedly. The function changes

cyclically.

NOTE

• If the unit is not going to be used for an extended period of

time, remove the batteries to prevent possible electrolyte

leakage.

• The remote control may not operate correctly when:

- The line of sight between the remote control and the remote

sensor in the display window is exposed to intense light, such

as direct sunlight.

- Other remote controls are used nearby (those of a television,

etc.)

Operating AIWA CD or DVD players with the remote

control

You can control the basic functions of AIWA CD or DVD players

with the remote control. In principle, the buttons described below

have the same function as those on the DVD or CD players.

For more details, refer to the operating instructions of the player.

Operating DVD and CD players

Press the following button.

l/a - Starts playback. The button pauses

CD playback as well.

f,g - Searches a track. Hold the button down.

r,t - Skips

a track of the CD. Press the button repeatedly.

s - Stops playback.

Operating DVD players

Press the following button while pressing the SHIFT button.

i,k,j,l (up, down, left or right) button - Moves the cursor to

select a program etc.

AUDIO button - Changes an audio track (language etc.)

ENTER button - Enters the selected program etc.

TITLE or MENU button - Enters the title or menu screen.

RETURN button - Returns to the previous mode etc.

DVD PAUSE - Pauses the playback of a DVD.

Operating CD players

Press the following button.

DISC SKIP (CD) - Skips a disc in the CD changer.

7

ENGLISH

To select the front speaker system

To use speaker system A: Set the FRONT SPEAKERS A button

to HON.

To use speaker system B: Set the FRONT SPEAKERS B button

to HON.

To use both speaker systems: Set both the buttons to HON.

Set the button(s) to hOFF to turn off the speaker system(s).

NOTE

As the front speaker systems A and B are connected in series:

- The sound will decrease slightly when using both speaker

systems

- No sound can be heard if the FRONT SPEAKERS A and B

buttons are set to HON when only one speaker system is

connected

To turn the unit off, press the POWER button.

POWER ECONOMIZING (ECO) MODE

Setting this unit to the ECO mode reduces power consumption

as below.

Initial setting of the ECO mode is ON.

• When the current time is set, the clock display disappears

immediately.

• While the power is off, all the display lights turn off, and only

the indicator on the left side of the display window lights in red.

To cancel the ECO mode

1 Press the ECO button to display ECO MODE while the unit is

turned on.

2 Within 4 seconds, press the ENTER button.

3 Within 4 seconds, turn the MULTI JOG to select ECO OFF.

The mode will be automatically set after 4 seconds. It will

also be set if the ENTER button is pressed within 4 seconds

after step 3.

BEFORE OPERATION

To turn the unit on

Press the POWER button.

Operation is possible after four seconds. The VOL (volume) level

or function name is displayed one after the other for the first four

seconds.

The selected function indicator lights up in red.

To change the brightness level of the display

1 Press the ECO button repeatedly until “DIM MODE” is

displayed.

2 Within 4 seconds, press the ENTER button.

3 Within 4 seconds, turn the MULTI JOG to select the dimmer

mode as below.

The mode will be automatically set after 4 seconds. It will

also be set if the ENTER button is pressed within 4 seconds

after step 3.

DIM-OFF: The normal display.

DIMMER 1: The illumination of the display is dimmer than

usual.

DIMMER 2: The illumination of the display is dimmer than

DIMMER 1. The function indicator turns off.

Using the headphones

Connect headphones to the PHONES jack with a standard stereo

plug (ø6.3 mm, 1/4 inch). Be sure to set the FRONT SPEAKERS

A and B buttons to hOFF. Otherwise sound is output from the

speakers.

NOTE

When the headphones are plugged in:

- The Dolby Pro Logic or DSP system is automatically canceled

- The Dolby Digital Surround mode is changed to the

“2chSTEREO (2CH DOWNMIX)” mode

-

EnEn

En

ENGLISH

8

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

CUSTOM AUDIO ADJUSTMENT

VOLUME CONTROL

Turn the VOLUME control on the unit, or press the VOL buttons

on the remote control.

The volume level is shown on the display for four seconds. It can

be adjusted between 0 and MAX (31). It flashes when set over

the level of 27.

The volume level remains memorized even after the power is

turned off. However, if the power is turned off when the volume

is set to 17 or more, it is automatically set to 16 the next time the

power is turned on.

To adjust the left/right balance of the front speakers

Press the BALANCE button to display “L/R 0dB”. Then press

the N or M button repeatedly or turn the MULTI JOG within

four seconds.

Note that the front speaker balance for the DOLBY SURROUND

is also changed.

To mute the sound temporarily

Press the MUTING (MUTE) button (–20 dB).

“MUTE ON” appears on the display for four seconds. While muting

the sound, the selected function indicator flashes. Press the

MUTING button again to restore the sound.

PREPARATIONS

SOUND

SUPER T-BASS SYSTEM

The T-BASS system enhances the realism of low-frequency

sound.

Press the T-BASS button.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

NOTE

Low-frequency sound may be distorted when the T-BASS system

is used for a disc or tape in which low-frequency sound is

originally emphasized. In this case, cancel the T-BASS system.

SOUND ADJUSTMENT DURING RECORDING

The output volume and tone of the speakers or headphones may

be freely varied without affecting the level of the recording.

9

ENGLISH

ELECTRONIC GRAPHIC

EQUALIZER

This unit provides the following five different equalization modes.

ROCK: Powerful sound emphasizing treble and bass

POP: More presence in the vocals and midrange

JAZZ: Accented lower frequencies for jazz-type music

CLASSIC: Enriched sound with heavy bass and fine treble

BGM: Calm tone with suppressed bass and treble

Press the GEQ (Graphic Equalizer) button, and turn the

MULTI JOG until the desired equalization mode is

displayed.

The GEQ modes are displayed cyclically as follows.

The selected mode name is displayed for four seconds, and the

GEQ indicator lights up.

To cancel the selected mode

Press the GEQ button to display the GEQ mode name, and press

the button again within 4 seconds. “GEQ OFF” appears on the

display.

To select with the remote control

Press the GEQ button repeatedly while pressing the SHIFT

button until the desired equalization mode is displayed.

Five preset modes and “GEQ OFF” can be selected.

Selected mode

EnEn

En

ENGLISH

10

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

DSP SURROUND

The DSP (Digital Signal Processor) surround circuits can recreate

the effect of sounds reflected from walls or ceilings, to obtain the

sound presence of real environments. The unit provides 5 DSP

preset modes. Some of them are accompanied with the matching

GEQ preset mode, and you can also select or turn off the GEQ

to suit your preference.

Press the DSP button, and turn the MULTI JOG until

the desired DSP mode is displayed.

The selected mode name is displayed for four seconds, and the

DSP indicator lights up. When the selected DSP mode is

accompanied with the matching GEQ mode, the GEQ indicator

lights up as well.

When the music source is monaural

The DSP system may not work effectively.

To cancel the selected mode

Press the DSP button to display the DSP mode name, and press

the button again within 4 seconds. “DSP OFF” appears on the

display. Even if canceling the selected DSP mode, the matching

or selected GEQ mode still remains.

To select with the remote control

1 Press the DSP button.

2 Within 4 seconds, press the TUNING UP or DOWN button

repeatedly while pressing the SHIFT button until the desired

DSP mode is displayed.

Ten preset modes can be selected.

To change the mode rapidly, hold down the TUNING UP or

DOWN button while pressing the SHIFT button.

To adjust the volume and balance of the surround

speakers

Press the MANUAL SELECT button on the remote control three

times to display “SUR 0dB” while the DSP system is turned on.

Then press the N or M button repeatedly or turn the MULTI

JOG within four seconds.

NOTE

The DSP surround system is automatically canceled and cannot

be turned on when headphones are plugged in.

SOUND

Selected mode

11

ENGLISH

BASIC OPERATIONS

To select the video source

1 Turn the FUNCTION to select PHONO, CD or AUX.

2 Press the ENTER button to display VIDEO 1.

3 Turn the MULTI JOG to select VIDEO 2 or VIDEO 3.

To change a displayed name for the VIDEO 1

and VIDEO 2

When the VIDEO 1 function is selected, VIDEO 1 is displayed

initially. It can be changed to DVD or MD.

Press the DIGITAL/ANALOG/BAND button while pressing the

ENTER button,

then release the ENTER button first.

The displayed name for the VIDEO 2 function can be changed

to VIDEO 2, LD or TV; while the VIDEO 2 function is selected,

press the DIGITAL/ANALOG/BAND button while pressing the

ENTER button,

then release the ENTER button first.

To select the “ANALOG” or “DIGITAL” (Dolby

Digital Surround) mode of the VIDEO 1 or

VIDEO 2 function

Press the DIGITAL/ANALOG/BAND button when the VIDEO 1

or VIDEO 2 is selected. The selected mode “ANALOG” or

“DIGITAL” appears on the display.

In the DIGITAL mode: Equipment connected to the OPTICAL

DIGITAL IN terminal is selected as a source for the VIDEO 1

function, and equipment connected to the COAXIAL DIGITAL

IN terminal for the VIDEO 2 function. The DIGITAL indicator

lights in red.

In the ANALOG mode: Equipment connected to the VIDEO 1/

DVD/MD IN terminals is selected as a source for the VIDEO 1

function, and equipment connected to the VIDEO 2/LD/TV

terminals for the VIDEO 2 function.

NOTE

The “DIGITAL” mode changes to the “ANALOG,” when pressing

the TAPE MONITOR button.

When the “OVER LEVEL” indicator lights up

The unit is equipped with the OVER LEVEL indicator. When input

analog signals from the connected equipment are too high to

accept, the indicator lights on the right side of the display. In this

case, adjust the input level as mentioned below so that the

indicator disappears.

To adjust the sound level of the connected source

The input sensitivity level of each function can be adjusted

(except the TUNER, VIDEO 1 (DIGITAL) and VIDEO 2 (DIGITAL)

functions).

When the sound level of the connected source is higher or lower

than that of the TUNER, adjust it as follows.

1 Select the function to be adjusted.

Turn the FUNCTION or press the TAPE MONITOR button

and play the source.

2 Press the N or M button repeatedly.

Adjust the level so that the “OVER LEVEL” indicator does not

light on the display.

• The level can be adjusted between -6dB (MIN) and +8dB

(MAX) in 2dB steps. Adjust the level so that the sound is

output at the same level as the TUNER.

• The input sensitivity level of the TAPE MONITOR can be

adjusted to 0dB or -6dB.

SELECTION OF AUDIO/VIDEO

SOURCE

1 Select the program source.

Turn the FUNCTION selector or press the TAPE MONITOR

button. The selected function indicator lights in red.

To listen to or watch The indicator in red

Tape TAPE MONITOR

Radio TUNER

Record PHONO

Compact disc CD

Television, etc. AUX

Video VIDEO 1/DVD/MD,

VIDEO 2/LD/TV, VIDEO 3

LD or Cable TV VIDEO 2/LD/TV

MD or DVD VIDEO 1/DVD/MD

The function to be selected (except PHONO) depends on the

equipment connected to the input terminals on the rear panel

of the unit.

To select with the remote control

Press the TAPE MONITOR button or the FUNCTION button

repeatedly.

NOTE

When using a turntable with a built-in equalizer amplifier, set

the switch of the equalizer amplifier to off. See the instructions

of the turntable for further information.

2 Start the selected program source.

3 Adjust the sound.

About the video source to the monitor or TV

The selected video source is indicated on the display and the

video signal through the MONITOR VIDEO OUT jack is output

on the TV.

V1: VIDEO 1, V2: VIDEO 2, V3: VIDEO 3

Selected video source

EnEn

En

ENGLISH

12

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

RECORDING AN AUDIO SOURCE

1 Select the program source to be recorded.

Turn the FUNCTION.

2 Set the tape deck or MD recorder to the recording

mode.

3 Start the selected program source.

To monitor recorded sound during recording (when the

connected tape deck is a three-head system)

Press the TAPE MONITOR button. “TAPE ON” appears on the

display for four seconds, and then the source name selected in

step 1 comes back on. To cancel the tape monitor, press it again

so that “TAPE OFF” appears.

NOTE

• Any sound control system has no effect on recording (see

page 8).

• Input sound through the DIGITAL IN terminals cannot be

recorded. When recording the sound from the DVD, CD, MD

or LD player, connect the analog AUDIO OUT terminals of

the player to the corresponding AUDIO IN terminals of the

receiver.

The sound will be recorded in 2 ch stereo.

• When recording audio sources by the MD recorder connected

to the VIDEO 1/DVD/MD AUDIO OUT terminals, the selected

video source (see page 11) should be V2 or V3. Recording

cannot be done while the V1 (VIDEO 1) is selected and

displayed on the window.

• Input sound from the tape deck connected to the TAPE

MONITOR IN terminals cannot be recorded.

TO PLAY A DVD OR LD RECORDED IN

DOLBY DIGITAL SURROUND

This receiver is equipped with the Dolby Digital decoder and

has the DIGITAL IN (both OPTICAL and COAXIAL) terminals.

When a DVD or LD player is connected to the DIGITAL IN terminal

of the receiver, you can enjoy theater-quality audio right in your

home when playing discs recorded in Dolby Digital Surround.

Before operation

• Check that the TAPE MONITOR is not selected. If the TAPE

MONITOR is selected, press the TAPE MONITOR button so

that “TAPE OFF” appears on the display.

• When connecting an LD player equipped with the AC-3 RF

OUT terminal, use an RF demodulator unit. Also connect the

analog AUDIO OUT terminals of the LD player to the receiver

to play all the sources. For further information, refer to the

instructions of the LD player.

1 Turn the FUNCTION to select the VIDEO 1 (VIDEO

2) and press the DIGITAL/ANALOG/BAND button

repeatedly until “DIGITAL” is displayed.

The DVD (LD) player connected to the OPTICAL (COAXIAL)

DIGITAL IN terminal is selected as a source.

2 Start playing the DVD (LD) recorded in Dolby

Digital Surround.

The “DOLBY DIGITAL” indicator will light on the display when

the bit stream of the Dolby Digital Surround comes in the

unit.

To select the Dolby Digital Surround mode according to your

speakers, see “SELECTING DOLBY SURROUND” on page

15.

NOTE

• While the TAPE MONITOR is selected and the TAPE MONITOR

indicator turns red, “DIGITAL” cannot be selected.

• When headphones are plugged in, the Dolby Digital Surround

mode is automatically changed to “2chSTEREO” and the “2CH

DOWNMIX” indicator lights on the display.

Even if the DOLBY SURROUND button is pressed while the

headphones are plugged in, the mode cannot be changed.

• This unit supports input signals of the Dolby Digital Surround

bit stream and linear PCM whose sampling frequency is 32

kHz, 44.1 kHz and 48 kHz. The unit cannot play the DVDs whose

sampling frequency is 96 kHz.

• When connecting some DVD players to the receiver through

the DIGITAL IN terminals, noise may be heard in the DVD

operation: e.g. searching a disc, skipping a chapter.

BASIC OPERATIONS

13

ENGLISH

MANUAL TUNING

1 Turn the FUNCTION to select the TUNER function,

and press the DIGITAL/ANALOG/BAND button

repeatedly to select the desired band.

The display changes to frequency indications after indicating

band and video source (V1, V2 or V3) for two seconds.

2 Press the N or M button to select a station.

Each time the button is pressed, the frequency changes.

When a station is received, “TUNE” is displayed for two

seconds. During FM stereo reception, 1 is displayed.

When operating with the remote control

Press the TUNER/BAND button while pressing the SHIFT button

in step 1, and the TUNING DOWN or UP button while pressing

the SHIFT button in step 2.

To search for a station quickly (Auto Search)

Keep the N or M button pressed until the tuner starts

searching for a station. After tuning in to a station, the search

stops.

To stop the Auto Search manually, press the N or M button.

When operating with the remote control, keep the TUNING UP

or DOWN button pressed while pressing the SHIFT button.

• The Auto Search may not stop at stations with very weak

signals.

When an FM stereo broadcast contains noise

Press the MONO TUNER button while pressing the SHIFT button

on the remote control so that “MONO” appears on the display.

Noise is reduced, although reception is monaural.

To restore stereo reception, repeat the above so that “STEREO”

appears.

RADIO RECEPTION

When the reception contains noise interference

Move the unit away from other electrical appliances, especially

digital audio devices, or turn off the appliances that generate

noise signals.

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If

you use this unit in an area where the frequency allocation

system is 9 kHz/step, change the tuning interval.

Hold down the DIGITAL/ANALOG/BAND button and press the

POWER button.

To reset the interval, repeat this procedure.

EnEn

En

ENGLISH

14

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

PRESETTING STATIONS

The unit can store a total of 32 preset stations. When a station is

stored, a preset number is assigned to the station. Use the preset

number to tune in to a preset station directly.

1 Turn the FUNCTION to select the TUNER function,

and press the DIGITAL/ANALOG/BAND button

repeatedly to select the desired band. Then press

the N or M button to select a station.

2 Press the ENTER button to store the station.

A preset number assigned to the station, beginning from 1 in

consecutive order for each band, appears in the display for

two seconds.

3 Repeat steps 1 and 2.

No more stations will be stored and “FULL” appears if a total

of 32 stations have already been stored for all the bands.

NOTE

When the AM tuning interval is changed, all preset stations are

cleared. The preset stations have to be set again.

PRESET NUMBER TUNING

1 Turn the FUNCTION to select the TUNER function,

and press the DIGITAL/ANALOG/BAND button

repeatedly to select a band.

2 Turn the MULTI JOG to select a preset number.

When operating with the remote control

Press the TUNER/BAND button while pressing the SHIFT button

to select a band, then press the numbered buttons to select a

preset number.

Example:

To select preset number 25, press 2 and 5.

To select preset number 7 press 0 and 7.

To clear a preset station

Select the preset number of the station to be cleared. Then, press

the ENTER button, and press it again within four seconds.

The preset numbers of all other stations in the band with higher

numbers are decreased by one.

RADIO RECEPTION

15

ENGLISH

The recommended mode

[Dolby Digital Surround]

[Dolby Pro Logic]

PHANTOM mode: Select this mode when the center speaker is

not connected. All center channel signals are redistributed to

the left and right channel speakers.

3 STEREO mode: Select this mode when the surround speakers

are not connected.

TO SELECT A DOLBY SURROUND MODE

Preparations

• When selecting a Dolby Digital Surround mode, select the

VIDEO 1 (DIGITAL) or VIDEO 2 (DIGITAL) function (see page

12) and play a disc recorded in Dolby Digital Surround

before selecting the mode.

• When selecting a Dolby Pro Logic mode, select the function

except VIDEO 1 (DIGITAL) and VIDEO 2 (DIGITAL) (DIGITAL).

1 Press the DOLBY SURROUND button and turn

the MULTI JOG to select the appropriate mode.

The selected mode name appears on the display.

[Dolby Digital Surround]

To select the 2chSTEREO mode, press the DOLBY

SURROUND button repeatedly until “2chSTEREO” appears.

NOTE

Select the Dolby Digital Surround mode while playing a source

recorded in Dolby Digital Surround.

[Dolby Pro Logic]

This unit is equipped with not only the Dolby Pro Logic decoder

but also the Dolby Digital decoder.

The unit and the center and surround speakers (standard) assure

full-scale home theater sound. When playing back discs or video

software that have been recorded in Dolby Pro Logic or Dolby

Digital Surround, astonishingly realistic sound surrounds the

listener to create a new level of audio/visual entertainment.

Independent control of the five channels allows the listener to

enjoy the same type of sound reproduction experienced in movie

theaters. Voices are reproduced in the front and center sound

field, while ambient sounds like cars and crowds are reproduced

on all sides of the listener for an incredibly lifelike audio/video

experience. Please read the following carefully to “tune” the

system’s output to match the characteristics of your listening

space.

Check the following:

• Before enjoying the DOLBY SURROUND sound, adjust the

speaker sound levels to the proper balance (see page 16).

• Make sure the speakers are properly connected and positioned

(see pages 4 and 5).

• Make sure the TV set and video unit are properly connected

(see page 3).

• Make sure the disc and video tape, etc., support Dolby Pro

Logic or Dolby Digital Surround.

SELECTING DOLBY SURROUND

The optimal Dolby Digital Surround and Dolby Pro Logic modes

and settings depend on the type and placement of the speakers.

It is recommended that the optional Aiwa speakers should be

used for all channels, for example, the SX-AVR2900 speaker

system.

Check the current type and placement of your speakers and

select the recommended mode accordingly.

DOLBY SURROUND

Center speaker

Larger-size

DOLBY

D-WIDE

3 STEREO-

WIDE

No speaker

PHANTOM

2chSTEREO

Smaller-size

DOLBY

D-NORMAL

3 STEREO-

NORMAL

Surround speaker

(Rear speaker)

No surround

speaker

Center speaker

No speaker

PHANTOM

–

Surround speaker

(Rear speaker)

No surround

speaker

Smaller-size

PRO LOGIC-

NORMAL

3 STEREO-

NORMAL

Larger-size

PRO LOGIC-

WIDE

3 STEREO-

WIDE

PRO LOGIC PHANTOM 3 STEREO

DOLBY D PHANTOM 3 STEREO

EnEn

En

ENGLISH

16

EE

E

(Españo(Españo

(Españo

FF

F

(França (França

(França

2 Press the DOLBY SURROUND button again and

hold it down until the center speaker mode to be

selected appears. (Except the 2chSTEREO and

PHANTOM modes.)

“NORMAL” and “WIDE” appear one after the other.

When operating with the remote control

Press the SURROUND button repeatedly to select the mode,

and hold it down to select the center speaker mode.

NOTE

• Depending on the sound source or listening condition, surround

effect may not be obtained even when the Dolby Digital

Surround or Dolby Pro Logic is selected.

• The full Dolby Digital Surround or Dolby Pro Logic effect cannot

be obtained when using software not recorded in the Dolby

Digital Surround or Dolby Pro Logic system. In this case, use

the DSP surround system instead (see page 10).

• When headphones are plugged in:

- The Dolby Pro Logic system is automatically canceled.

- The Dolby Digital Surround mode is automatically changed

to “2chSTEREO.”

• While headphones are plugged in:

- The Dolby Pro Logic cannot be turned on.

- The Dolby Digital Surround mode cannot be changed.

ADJUSTING SPEAKER LEVEL

BALANCE

The unit is equipped with a built-in test signal generator called a

noise sequencer for easy balance adjustment of all five channels.

The sequencer outputs a noise signal that “travels” from channel

to channel, enabling the simple adjustment of sound level to

achieve the same apparent loudness, at your listening position,

from each channel.

1 Select the Dolby Digital Surround (except

“2chSTEREO”) or Dolby Pro Logic mode

according to the current type and placement of

your speakers.

(See page 15.)

2 Press the MANUAL SELECT button on the remote

control and hold it down for about two seconds

until “L” of “L/R 0dB” starts to flash.

A noise signal is sent to each channel in turn as follows:

DOLBY D (PRO LOGIC) NORMAL or WIDE mode

DOLBY SURROUND

To be continued

17

ENGLISH

PHANTOM mode

3 STEREO NORMAL or WIDE mode

* “L” or “R” flashes to indicate one of the front speakers from

which the noise signal is output.

3 Adjust the sound level of the center and surround

speakers.

While “CEN,” “S-L” or “S-R” flashes in the display, press the

TUNING UP or DOWN button while pressing the SHIFT button

on the remote control so that the sound level of the center or

surround speakers matches that of the front speakers.

The balance of the front speakers can be adjusted as well

while “L/R” is displayed.

NOTE

The N or M button on the main unit cannot be used.

4 Press the MANUAL SELECT button again to stop

the noise signal.

NOTE

When adjusting the speaker level balance of the Dolby Digital

Surround, that of the Dolby Pro Logic is also changed and vice

versa.

About the channels

The left and right speakers create the stereo effect.

The center speaker helps precise sound positioning over a

broad sound field.

The rear-mounted surround speakers enhance the “depth” of

the sound field.

To change the delay time of the surround speakers or

center speaker when using the Dolby Digital Surround

or Dolby Pro Logic mode

While the Dolby Digital Surround (except “2chSTEREO”) or Dolby

Pro Logic is activated, press the MANUAL SELECT button on

the remote control repeatedly so that “CEN 0mS” or “SUR 5mS”

(SUR 20mS) is displayed. Then, within 4 seconds, press the

N or M button or turn the MULTI JOG. The delay time changes

as shown below.

[Center speaker]

Adjust the delay time so that lines (voice in a movie) are heard

clearly and naturally.

The center speaker delay time is initially set to 0 ms

(milliseconds). It can be adjusted between 0 and 5 ms in 1 ms

step.

[Surround speakers]

Adjust the delay time to suite your preference.

Dolby Digital Surround

The speakers delay time is initially set to 5 ms. It can be adjusted

between 0 and 15 ms in 5 ms steps.

Dolby Pro Logic

The speakers delay time is initially set to 20 ms. It can be adjusted

between 15 and 30 ms in 5 ms steps.

NOTE

• When adjusting the delay time of the surround speakers or

center speaker for the Dolby Digital Surround, that of the Dolby

Pro Logic is changed and vice versa.

• When the surround speakers delay time of the Dolby Digital

Surround is set to 0 ms (5 ms, 10 ms , or 15 ms), that of the

Dolby Pro Logic is set to 15 ms (20 ms, 25 ms or 30 ms), and

vice versa.

To adjust the speaker level balance while listening to the

source

The speaker level balance can be changed after adjusting it with

the noise sequencer. The balance can be changed whenever

the Dolby Digital Surround or Dolby Pro Logic system is activated.

1 Play a disc or video software recorded in Dolby Pro Logic or

Dolby Digital Surround.

2 Press the MANUAL SELECT button on the remote control

repeatedly so that “L/R,” “CEN,” “S-L” or “S-R” appears on the

display.

3 Press the N or M button or turn the MULTI JOG while the

speaker name to be adjusted is displayed.

La page est en cours de chargement...

Aiwa AV-D57 Operating Instructions Manual

Aiwa AV-D57 Operating Instructions Manual

dans d''autres langues

Documents connexes