Gaggenau USA RW414761 Guide d'installation

Gaggenau

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES DE INSTALACIÓN

RC 462/472

RF 411/413

RF 461/463

RF 471

RW 414/

464

2

INSTALLATION INSTRUCTIONS ........... 3

INSTRUCTIONS D’INSTALLATION ........ 36

INSTRUCCIONES DE INSTALACIÓN..... 70

3

Content

Important Safety Instructions ............................ 5

Installation options ............................................. 6

Individual appliance .................................................. 6

Side-by-Side ................................................................ 6

Individual appliances with partition ........................ 6

Individual appliance at the end of the kitchen ........ 6

Installing the appliance ...................................... 6

Installation location .................................................... 7

Atmosphere grades ................................................... 7

Stable installation ....................................................... 7

Installation niche ........................................................ 7

Neighbouring kitchen furniture ................................ 7

Floor ............................................................................. 7

Aligning the appliance .............................................. 8

Electrical connection .......................................... 8

Water connection ................................................ 8

Dimensions of the installation niche ................. 9

Required accessories and tools ........................ 10

Supplied accessories ................................................ 10

Optional accessories ................................................ 10

Other ............................................................................ 10

Tools ............................................................................. 10

Installation instructions ...................................... 11

1. Check the installation niche ................ 11

2. Removing the packaging ..................... 11

3. Transport of the appliance ................... 12

4. Installation preparation ......................... 12

5. Special installation ................................. 12

1. Attaching the anti-tilt brackets ............. 13

2. Attaching an alternative

anti-tilt device .......................................... 14

3. Attaching the edge protectors ............ 14

4. Attaching the fastening sheets

(lateral) 14

1. Pushing the appliance into

the installation niche .............................. 15

2. Aligning the appliance

in the niche .............................................. 16

3. Attaching the appliance to

the niche ceiling ..................................... 17

4. Fastening the appliance to the side

wall of the installation niche ................. 18

1. Attaching the toe kick panel ................ 19

2. Aligning the base panel ........................ 19

3. Switching the appliance on

for the first time ....................................... 20

4. Preparing the furniture doors .............. 20

5. Loading the appliance door ................ 21

6. Removing positioning aids .................. 21

7. Fastening the adjusting rib

to the furniture door ............................... 21

8. Fastening the fixing rib

to the furniture door ............................... 22

9. Mounting the furniture door ................. 23

10. Screw on the lower fixing angle ......... 24

4

1. Attaching the covers .......................... 25

2. Mounting the air seperator ................ 25

3. Tensioning the hinge springs ........... 26

Special installation steps ................................... 26

Changing over the door hinges .................. 27

Removing/changing the sealing mat ........ 29

Side-by-Side installation ................................ 30

Preparing to connect the water ................... 32

Connecting the water to the appliance ..... 33

Aligning ice and water dispenser ............... 33

Attaching covering strips .............................. 34

Adjusting the door opening angle .............. 35

5

Important Safety Instructions

These mounting instructions are designed to help you

install your new appliance.

The manufacturer cannot be held liable for mounting

which has been improperly carried out. We recommend

that you allow a qualified specialist to set up and switch

the appliance on for the first time.

Following all information and keeping to the instructions

are preconditions for mounting and switching the

appliance on safely for the first time.

Keep the mounting instructions safe for use later on.

Before setting up and switching the appliance on for the

first time, read the mounting instructions fully and

thoroughly.

ã WARNING

These appliances are top-heavy and must be

secured to prevent the possibility of tipping forward.

Anti-tip protection is required.

Keep doors closed until the appliance is completely

installed and secured per installation instructions.

Due to the weight and size of this appliance, and to

reduce the risk of personal injury or damage to the

product – TWO PEOPLE ARE REQUIRED FOR

PROPER INSTALLATION.

This appliance must be properly grounded. See the

section on “Connecting the power”.

Use this appliance only for its intended purpose.

Immediately repair or replace electric service cords

that become frayed or damaged.

Unplug the appliance or switch off the fuse before

cleaning or making repairs.

Repairs should be made by a qualified service

technician.

ã CAUTION

Installation of this appliance requires basic

mechanical, carpentry and plumbing skills.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the Appliance Warranty.

See the Owner's Manual for warranty information.

Important

Save these instructions for local inspector's use. Observe

all governing codes and ordinances.

Note to Installer – Be sure to leave these instructions

with the Consumer.

Note to Consumer – Keep these instructions with your

Owner's Manual for future reference.

General

These installation instructions are intended for use by

qualified installers. All connections for water, electrical

power and grounding must comply with local codes and

ordinances and be made by licensed personnel when

required. In the absence of a local code:

– In the U.S.A., in accordance with the National Electric

Code, ANSI/NFPA70 – latest edition/State and

Municipal codes and/or local codes.

– In Canada, in accordance with the Canadian Electric

Code C22.1 – latest edition/Provincial and Municipal

codes and/or local codes.

Definitions

ã

WARNING

This indicates that death or serious injuries may

occur as a result of not observing this warning.

ã CAUTION

This indicates that minor or moderate injuries or

damage may occur as a result of not observing

this warning.

Note:

This is used to draw the user's attention to something in

particular.

6

Installation options

Various installation possibilities are available.

These are only limited by the kitchen design.

Individual appliance

Side-by-Side

If two appliances are set up next to each other, a sealing

kit for Side-by-Side combination should be used in order

to guarantee a stable connection.

For further information see section “Required

accessories and tools”.

Individual appliances with partition

– When dimensioning the partition for model 4, note

the thickness of the door panels to prevent damage

if the doors are opened at the same time.

– Use the Heater Kit for Side-by-Side Installation if the

gap between the appliances is less than 6" (160

mm).

See the section on “Required accessories and tools/

Optional accessories”.

– Minimum thickness of the partition

5

/

8

" (16 mm).

Individual appliance at the end of the

kitchen

If one side of the appliance is visible, a side panel must

be used.

The side panel must be connected firmly to the wall, the

floor and overhead cabinet/fixtures before the appliance

is placed in the installation niche.

The dimensions of the side panel are taken from the

opposite installation niche wall. During installation ensure

that the installation niche is square and the proper size.

7

Installing the appliance

Installation location

ã

WARNING

The fully laden appliance is very heavy.

* without water and ice dispenser

The appliance should be installed in a dry, well ventilated

space.

The location should not be exposed to the direct sunlight

and should not lie next to a source of heat such as a

cooker or a radiator etc. If installation next to a source of

heat cannot be avoided, either a suitable insulating plate

should be used or you should keep to the following

minimum distances:

–1

1

/

4

" (3 cm) to electric or gas cookers.

–11

13

/

16

" (30 cm) to an oil-fired or solid-fuel cooker.

The floor of the installation location must not give way; if

required, reinforce floor. To ensure that the ice maker

functions correctly, the appliance must be upright.

Climatic classes

The climate class can be found on the rating plate.

The climate class indicates within which ambient

temperatures the appliance can be operated.

Stable installation

The appliance is very heavy and has a tendency to tilt

forwards when the appliance door is opened.

The appliance must not be switched on until there

is no possibility of the appliance tilting over.

The safest method of installing the appliance in a stable

position is to use the supplied anti-tip brackets.

If the installation niche is adequately stable and the

appliance can be attached securely to the upper and side

walls of the niche, it may be possible to dispense with the

anti-tip brackets. A prerequisite for this is always a firm

connection between the niche and back wall!

In the case of doubt, the help of architect or specialist

builder should be enlisted.

Installation niche

It is important to keep to the stated dimensions of the

installation niche with a view to trouble-free fitting, and the

subsequent appearance of the kitchen furniture frontage.

Special care should be taken that the niche has right

angles. The side walls should not exhibit areas that stick

out, projections or unevenness.

You should determine the right angles of the installation

niche with appropriate means, e.g. by measuring

diagonally and by using a spirit level.

The side walls and the upper end of the installation niche

must be at least

5

/

8

" (16 mm) thick.

Neighbouring kitchen furniture

The new appliance is screwed down tightly using parts of

the cabinet and the upper cabinet.

Care should therefore be taken, that all upper cabinets to

which something has been fastened are securely

connected to the subsurface or wall by appropriate

means.

The minimum thickness of the base should be

a minimum of 19 mm.

Floor

The subsurface must be level and even in order to ensure

that the appliance is securely installed and works

correctly.

The subsurface must be made from a hard, non-flexible

material.

The floor of the installation space must have the same

height as the rest of the space.

On account of the weight of a fully-laden appliance, it is

necessary to have a bearing subsurface. In the case of

doubt, the help of architect or specialist builder should be

enlisted.

Appliance width Weight (laden)

approx.

Refrigerator 24" (60.3 cm) 890 lbs (400 kg)

Refrigerator 30" (75.6 cm) 1111 lbs (500 kg)

Freezer 18" (45.1 cm) * 555 lbs (250 kg)

Freezer 24" (60.3 cm) * 778 lbs (350 kg)

Freezer 30" (75.6 cm) * 944 lbs (425 kg)

Wine storage cabinet 18" (45.1 cm) 544 lbs (245 kg)

Wine storage cabinet 24" (60.3 cm) 689 lbs (310 kg)

Climatic class Permitted ambient temperature

SN

50 °F to 90 °F (+10 °C to 32 °C)

N

61 °F to 90 °F (+16 °C to 32 °C)

ST

61 °F to 100 °F (+16 °C to 38 °C)

T

61 °F to 110 °F (+16 °C to 43 °C)

8

Aligning the appliance

To ensure that the appliance functions correctly, it must

be set level with a spirit level.

If the appliance is not level, water may flow out of the ice

maker, ice cubes may be irregular or the doors may not

close properly.

Electrical connection

ã WARNING

– Avoid the risk of an electric shock!

– Insert into a grounded 3-phase socket.

Never remove grounding phase. Do not use any

adapters. Do not use any extension cables.

– Non-compliance with these instructions may

result in death, fire or an electric shock. Improper

connection of the protective conductor may

result in an electric shock. If you are in doubt

whether the appliance has been grounded

properly, have the appliance tested by a

qualified electrician or service technician.

The socket must be near the appliance and also freely

accessible following installation of the appliance.

The appliance complies with protection class I.

Connect the appliance to 115 V/60 Hz alternating current

via a correctly installed socket with protective conductor.

The socket must be fused with a 10 to 16 A fuse.

The appliance comes with a UL registered 3-wire power

cord. The appliance requires a 3-pole socket. Please

observe the following table with regard to this:

Check on the rating plate whether the indicated voltage

and current type correspond with the values of your

power supply. The location of the rating plate can be

found in the chapter entitled Customer service.

ã WARNING

Never connect the appliance to electronic energy

saver plugs. Our appliances can be used with

mains and sine-controlled inverters. Mains-

controlled inverters are used for photovoltaic

systems which are connected directly to the

national grid. Sine-controlled inverters must be

used for isolated applications (e.g. on ships or in

mountain lodges) which are not connected directly

to the national grid.

Water connection

ã CAUTION

Connect the appliance to a drinking water line.

The water may be connected only by a competent fitter

according to the local regulations of the appropriate

water supply company.

A cold water connection is necessary for operating the

automatic ice maker. The water pressure must be

between 25 and 120 p.s.i. (1,72 and 8,25 bar).

The installation must correspond to the local plumbing

regulations.

A separate shut-off valve should be installed in the cold-

water inflow. The shut-off valve should not be located

behind the appliance. It is recommended that you mount

the shut-off valve directly next to the appliance or at

another place which is easily accessible. When installing

the water connection, pay attention to the permissible

installation area for the water mains.

For connection to the drinking water mains use only water

pipes which are suitable for drinking water. Observe

national regulations and the connection conditions of the

local water supply companies.

When installing the water connection, observe the

permitted installation areas for the pipe. For the permitted

installation areas and dimensions see “Dimensions of the

installation niche”.

The maximum outside diameter of the water mains

(without connecting pieces) is

3

/

8

" (9.5 mm).

Appliance Maximum

simultaneous

load

Refrigerator 24" (60.3 cm) 2.0 amps

Refrigerator 30" (75.6 cm) 2.0 amps

Freezer 18" (45.1 cm) * 3.5 amps

Freezer 24" (60.3 cm) * 4.0 amps

Freezer 30" (75.6 cm) * 4.5 amps

Wine storage cabinet 18" (45.1 cm) 2.0 amps

Wine storage cabinet 24" (60.3 cm) 2.0 amps

9

Dimensions of the installation niche

Legend:

A Area for installation of the water connection

It is recommended the water-box be placed adjacent to the installation niche, so that it can be accessed for service

without uninstalling the appliance. If this is not possible, place the recessed water box within the shaded area.

B Area for installation of the power connection

C Opening depth of niche, depending on kitchen design

C = 24" (610 mm) minimum

Important:

The lateral niche walls must be

completely even and free from bumps.

If the niche is formed as a separate part,

the side walls must be completely even

up to a depth of at least 4“ (100 mm) and

free from bumps.

Appliance X Y

17¾“ 18“ 9“

(451 mm) (457 mm) (229 mm)

23

¾“ 24“ 12“

(603 mm) (610 mm) (305 mm)

29

¾“ 30“ 15“

(756 mm) (762 mm)

(381 mm)

10

Required accessories and tools

Supplied accessories

– Installation instructions

– Operating instructions

– Installation kit

Optional accessories

Installation accessories for Side-by-Side installation

For permanent connection of two individual appliances,

e.g. Freezer next to Refrigerator.

Lateral additional heating

If the gap between the appliances is less

than 6" (160 mm).

Connecting element for furniture doors

For connection of two door panels (see explanation in

Section “4. Preparing the furniture doors”). Can be used

for standard height door panels without further

preliminary work.

Miscellaneous

– Stepladder

– Dolly, hand truck

– Hammer drill for drilling holes in wall or floor

– Bits according suitable for material and in different

sizes

– Wooden beam (cross section min. 3" x 4") as an

alternative tip protection, length according to the

width of the installation niche

– Wooden screws in different sizes

– Thin plywood sheet, particle board or cardboard to

protect the floor from damage

– Suitable material for covering and protecting furniture

(e.g. protective sheets)

– Adhesive tape

Note:

Before using, check whether the removed adhesive

tape leaves adhesive residue on the work surfaces!

Otherwise do not use on high-quality work surfaces.

Tools

Cordless screwdriver

T20 Torx-bit magnetic

holder

T20 Torx screwdriver

5

/

16

" (8 mm) socket

wrench

Various size drills

Open end wrench

1

/

2

"

(SW 13 mm)

Multigrip pliers

Adjustable wrench

Cutter with adjustable

blade

Metal tape measure,

folding ruler

Square

2' (60 cm) and 4' (1 ,2 m)

spirit levels

Level, min. 4' (1 ,2 m) long

11

Installation instructions

The following installation instructions describe the

installation steps for various appliance types.

Therefore the diagrams may be a general representation

of your appliance.

Particular reference is made to special installation steps

for individual appliance types..

1. Check the installation niche

CAUTION

Use the following check list for a safe and trouble

free installation.

1. Check the floor.

See section on “Installing the appliance/Floor”.

2. Check the dimensions of the installation niche, see

“Dimensions of the installation niche”.

3. Check that the installation niche is square.

4. Check location of the soc

ket.

See section on “Electrical connection” and in the

section on “Dimensions of the installation niche”.

5. Check location of the water connection

(only for appliances with ice maker).

See section on “Water connection” and in the section

on “Dimensions of the installation niche”.

6. Check attachment of the adjacent cabinet/fixtures.

All cabinet parts in the vicinity of the appliance must

be connected securely to the wall.

7. Check that adjacent cabinet/fixtures have adequate

clearance (door opening angle).

2. Removing the packaging

WARNING

Risk of personal injury and damage to the

appliance!

– The a

ppliance could tilt over when unpacking.

– The appliance could tilt over when the appliance

door is opened.

– The appliance is very heavy.

Data relating to the weight when empty is found

in the following table:

* without water and ice dispenser

Note:

Check appliance for damage in transit.

Do not install the appliance if it is visibly damaged.

If in doubt, contact your dealer.

To avoid floor damage:

1. Remove the packaging carton and be careful not to

damage the surface of appliance.

2. Place packaging cardboard or plywood under the

appliance.

3. Remove accessories from the

outside

of the appliance.

Save adhesive tape which was used to attach

the supplied accessories to the appliance.

It can be used subsequently for attaching an edge

protection to the installation niche walls (see section

on “A / 3. Attaching the edge protectors”).

4. Remove transportation protection devices (a) and lift

appliance off the pallet – appliance is very heavy!

5. Carefully open the appliance – risk of tipping over –

and remove accessories and installation materials

from inside the appliance. Close the door again.

Note:

Do not remove transportation safety devices wh

ich

protect the shelves and storage compartments inside

the appliance until the installation is complete,

otherwise the parts may be damaged.

Appliance width Weight (empty)

approx.

Refrigerator 24" (60.3 cm) 291 lbs (131 kg)

Refrigerator 30" (75.6 cm) 322 lbs (145 kg)

Freezer 18" (45.1 cm) * 242 lbs (109 kg)

Freezer 24" (60.3 cm) * 291 lbs (131 kg)

Freezer 30" (75.6 cm) * 322 lbs (145 kg)

Wine storage cabinet 18" (45.1 cm) 242 lbs (109 kg)

Wine storage cabinet 24" (60.3 cm) 291 lbs (131 kg)

Appliance width Weight (empty)

approx.

a

12

3. Transport of the appliance

ã WARNING

Be careful, otherwise people who are helping may

be injured or the appliance may be damaged.

The appliance is very heavy.

The appliance is 83

1

/

8

" (2126 mm) tall. If the appliance

cannot be transported in an upright position,

the appliance can be transported horizontally.

Note:

Do not raise up the appliance via the side panels. Risk of

damage to the appliance!

When raising up the appliance, observe the required

minimum height at the installation location according to

the following table:

Note:

Always use the appliance dolly from the rear side of the

appliance. Never push it in from the front under the

appliance. Risk of damage to the appliance.

!

1. Transport the appliance to a suitable installation

location with suitable means of transportation (trolley,

lifting truck or hand).

2. Secure the appliance during transportation to

prevent it from tipping.

4. Installation preparation

Unpack installation materials and accessories.

To simplify installation, the packages are identified with

labels A, B, C and D corresponding with the manual

sections.

5. Special installation

The following symbol indicates that additional steps need

to be taken before proceeding to the next chapter.

Special installation steps are described after section D.

– Change over door hinge, see

“Changing over the door hinges”.

– Sealing mat, see “Removing/changing

over the sealing mat”

– Side-by-Side installation, see “Side-by-

Side installation”.

– Connecting the water, see “Preparing

to connect the water” and “Connecting

the water to the appliance”.

– Ice-water dispenser, see “Aligning the

ice-water dispenser“.

– Cover strips for a wine unit, see

“Attaching the cover strips”

– Door limitation pin, see “Adjusting the

door opening angle”.

Raise up via

appliance rear

Do not raise up from

appliance side

Minimum height

86"/2185 mm

Do not raise up the

appliance via the side

panels!

13

1. Attaching the anti-tip brackets

ã WARNING

Risk of injury and damage!

Assure that there are no electrical wires or

plumbing in the area which the screws could

penetrate.

ã WARNING

Risk of injury! Always wear safety glasses and

other necessary protective devices or apparel

when installing or working with dowels.

Important note:

If a Side-by-Side set up of two appliances is envisaged,

the anti-tip brackets are needed as installation aid.

Connect the appliances before the anti-tip brackets are

fixed to the wall, see “Side-by-Side installation”.

Notes:

– Each appliance requires 2 anti-tip brackets.

– The set supplied, contains fastening screws for

various subsurfaces. Select the fastening screws

corresponding to the local conditions.

– If the anti-tip brackets, and therefore the appliance,

cannot be securely attached with the supplied

fastening screws, another suitable method must be

used to attach the appliance securely.

The anti-tip-brackets (a) must overlap a minimum of

2

1

/

8

” (54 mm) over the appliance to secure the

appliance.

If this minimum length cannot be observed for structural

conditions it is possible to do this by fastening

a spacer (b) behind the anti-tip angle, e.g. a sufficiently

dimensioned wood board.

The length of the plank should correspond to the width of

the installation niche!

1. Specify the attachment points of the anti-tip-brackets

according to the section on “Dimensions of the

installation niche”.

2. Attach the anti-tip-brackets completely.

Be sure screws hold tight.

Important notes for fastening with dowels and screws:

– Not recommended for use in light-weight masonry

material such as cinder block.

– Not recommended for use in new concrete which

has not had time to cure.

– Do not use spiral-flute counterbores (countersinking

tool) to drill the holes.

14

2. Attaching an alternative anti-tip

device

Important note:

If the anti-tip brackets cannot be attached securely,

an alternative anti-tip-device can be attached. However,

ensure that there is no play between the appliance and

the anti-tip-device. If possible, always screw the wooden

beam to existing studs on the rear panel of the installation

niche.

1. Saw the wooden beam (cross section min. 3" x 4")

to the required length. Length is equal to the width of

the installation niche!

Notes:

– If the installation niche is deeper than the

appliance, select a beam which has a larger

cross section or attach 2 beams.

– The beam must cover the appliance by

at least 2" (50.8 mm).

2. Mark the installation height (lower edge of the beam)

on the rear panel of the installation niche.

3. Select screws according to the thickness of the

wooden beam: length = min. 2.5 x beam thickness,

diameter #12 or #14.

Note:

Choose the number of screws according to the

installation niche width, thereby ensuring that the

beam can be attached securely.

4. Depending to the subsurface:

Locate wall studs in the rear of the installation niche

and accordingly transfer their location to the wooden

beam

or

fasten suitable dowel into the rear wall.

5. Predrill the wooden beam.

6. Attach the wooden beam to the rear panel of the

installation niche.

3. Attaching the edge protectors

To protect the edges of the installation niche, it is

recommended to attach edge protection made of

asuitable material.

Attach the edge protection with the adhesive tape which

was used to attach the accessories to the appliance.

4. Attaching the fastening sheets

(lateral)

Attach the fastening sheets (lateral) to the appliance.

The following are special installation

steps. Instructions are provided after

section D.

– Change over door hinge, see

“Changing over the door hinges”.

– Sealing mat, see “Removing/changing

the sealing mat”.

– Side-by-Side installation, see “Side-by-

Side installation”.

– Connecting the water, see “Preparing

to connect the water”.

15

1. Pushing the appliance into the

installation niche

ã CAUTION

Caution when pushing the appliance into the

installation niche. Do not damage the water line or

power cord.

Note:

When the floor or the appliance is not leveled in

comparison to the installation niche adjust height

adjustable wheels before you move the appliance into the

installation niche.

1. Remove the base panel.

2. Raise the height-adjustable wheels at the back

by approx.

3

/

8

" (9.5 mm).

3. Put the electric plug into the socket.

4. Push the water line into the guard tube (a) at the rear

of the appliance.

ã WARNING

The appliance may tilt when the water connection

line is inserted into the protective pipe (a)!

5. Prevent the power cord from becoming caught.

Tie a piece of string to the middle of the power cord

and feed forwards over the top of the appliance.

When pushing in the appliance, pull the cable

upwards. Take care not to pinch the power cord.

or

Using adhesive tape, tape the power cord to the floor

centrally behind the appliance approx. 15" (380 mm)

away from the rear panel of the installation niche.

6. Carefully push the appliance into the installation

niche.

7. Remove edge protection (if attached).

16

2. Aligning the appliance in the niche

Note:

To ensure that the appliance functions correctly, it must

be set perfectly levelled.

Depth alignment

The positioning aid on the door have been designed for

the following total thickness of door panels:

–

3

/

4

" (19 mm)

–1

1

/

2

" (38 mm)

Always take account of the possible differing thickness of

the panel fronts which are to be fitted subsequently.

1. Align the appliance with the cabinet fronts using the

positioning aid.

Place level over the positioning aid on the door.

Height alignment

Notes:

– Do not twist or jam the appliance inside the

installation niche! When adjusting the height-

adjustable feet, proceed gradually: Always alternate

between left and right, etc.

– For easier adjustment of the rear feet take the weight

off by slightly tilting the appliance forward.

– When using a wooden beam as an alternative anti-tip

mechanism, turn the appliance as far as it will go

against the wooden beam. Do not bend against the

wooden beam.

The height-adjustable feet at the front and rear can all be

adjusted from the front.

Front: with open-ended wrench

1

/

2

"

(Width across flats 13 mm)

Rear: with

5

/

16

" (8 mm) hex nut driver via flexible

shaft.

The mark (a) attached at the appliance base is used as

a standard gage for height adjustment. When adjusting

the height, align this mark at a height of 1

1

/

2

" (32 mm)

above the floor.

It is very important to comply with this dimension for the

subsequent alignment of the furniture fronts.

The height adjustment gauge (b) is used

to set this height correctly. The upper

edge of the gauge must be in alignment

with the mark on the appliance.

2. Unscrew the feet at the front of the appliance until the

mark (a) on the appliance is in alignment with the

upper edge of the height adjustment gauge (b).

3. Align the appliance vertically using the feet

at the back. Use a level!

17

3. Attaching the appliance to the niche

ceiling

Note:

It is essential to attach the appliance to the top of the

installation niche.

1. Screw the attachment plate lugs (top) to the

overhead furniture.

2. If there is a fairly large gap above the appliance,

fit a wooden beam above the appliance, ensuring

that the wooden beam fits the gap exactly.

3. If there is enough room on the top of the appliance,

fix the attachment plate side lugs (top) to the side of

the niche.

Note:

In the case of a side-by-side installation connect both

cover rails to the bolt included in the installation

accessories for side-by-sid

e installation.

4.

5.

6.

Shorten the fitting strip (a), to fill the gap.

Note: The appliance will be damaged if the fitting

strip is too long.

Press fitting strip (a) into the cover strip.

Attach the cover strip (b) to the attachment plate

(top).

18

4. Fastening the appliance to the side

wall of the installation niche

1. Screw on the bars of the fastening sheets (lateral)

with the cabinet parts located next to them.

2. Screw on the brackets (a) for holding the cover strip.

3. Attach the cover strips (c) to the fastening sheets (b)

and the brackets (a).

The following is a special installation

step. Instructions are provided after

section D.

– Connecting the water, see

“Connecting the water to the

appliance”.

19

1. Attaching the toe kick panel

Note:

Risk of damage to the appliance. Do not cover ventilation

openings in the base panel.

Nominal dimensions to be observed:

1. Where necessary, cut the base strip to the required

length.

2. Place base panel on the appliance

(do not screw on).

3. Take the protective film off from the adhesive pads

on the Velcro strip.

4. Put the base strip onto the base panel and push

firmly.

5. Base strip can be screwed to the base panel from

behind. There are holes in the base panel for this

purpose.

2. Aligning the base panel

1. Place base panel on the appliance (do not screw on).

2. Measure the difference in depth A between the base

panel and the base strip of the adjacent lower

cabinets.

3. Remove the base panel again.

4. Adjust the brackets (a) to the dimensions A and

tighten.

5. Fasten the base panel.

20

3. Switching the appliance on for the

first time

To guarantee the accuracy of the following working steps

and thus the appearance of the overall kitchen front later

on, the appliance should now be operated.

1. Open the appliance door.

2. Press the POWER button.

3. Press the POWER button again to shut off.

Only for appliances with a water connection:

In order to avoid the risk of damage caused by leaking

water from damage possibly caused to the water pipe

feeding the appliance, keep the shut-off valve closed.

4. Preparing the furniture doors

Important note:

When working on the furniture doors, care should be

taken to the following:

– Always carry out screwing jobs on the most stable

part of the furniture door. Never screw into fillings or

similar areas.

– Always selects screws with a length smaller than the

thickness of the cabinet front.

– Protect the surfaces of the furniture doors during

installation against damage.

The overall weight of the furniture door including the

handle should not exceed the following values:

* Wine storage compartment

Instead of one large door, two furniture doors can be

mounted next to each other in the case of appliances with

a width of 76 and 91 cm. These furniture doors are then

connected using a metal strip on the rear.

This metal strip is available from your dealer as an

installation accessory (Connection element for furniture

doors). For further information see section “Tools and

Accessories which are needed”.

Note:

The instructions for carrying out this work step can be

found in the separate installation instructions for this

accessory.

Important information for furniture doors with cutout

(appliances with ice and water dispenser, wine storage

cabinets):

The cut edges of the door cutout must be protected

before humidity penetrates. To do this, use the means

suitable for the material and the shape of the furniture

door (e. g. edge veneer, edge sealant).

Appliance width Overall width of the furniture door

18“ (45.1 cm) 44 lbs (20 kg)

19 lbs* (8.5 kg *)

24“ (60.3 cm) 55 lbs (25 kg)

32 lbs* (14.5 kg *)

30“ (75.6 cm) 64 lbs (29 kg)

La page charge ...

Gaggenau USA RW414761 Guide d'installation

Gaggenau USA RW414761 Guide d'installation

dans d''autres langues

Autres documents