Tripp Lite TRIPP-LITE PDUMH15HVAT Metered Rack-Mount PDU Le manuel du propriétaire

Marque: Tripp Lite

Modèle: TRIPP-LITE PDUMH15HVAT Metered Rack-Mount PDU

Taper: Le manuel du propriétaire

Owner’s Manual

Metered Rack-Mount PDU

with Automatic Transfer Switch

Models: PDUMH15HVAT, PDUMH15HVATNET, PDUMH20HVAT,

PDUMH20HVAT1, PDUMH20HVATNET, PDUMH20HVATS,

PDUMNH20HVAT1

Series Number: AGAC7625

1. Important Safety Instructions 2

2. Installation 4

2.1 Mounting the PDU 4

2.2 Connecting the PDU 4

2.3 Networking the PDU 6

3. Features 7

4. Conﬁguration and Operation 10

4.1 Automatic Transfer Switch 10

5. Warranty and Product Registration 12

Español 13

Français 25

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

WARRANTY REGISTRATION

automatically entered to win an ISOBAR®

surge protector in our monthly drawing!

tripplite.com/warranty

SAVE THESE INSTRUCTIONS

• This manual contains instructions and warnings that should be followed

during the installation, operation and storage of this product. Failure to

heed these instructions and warnings may affect the product warranty.

• Warning: This equipment is compliant with Class A of CISPR 32. In a

residential environment, this equipment may cause radio interference.

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 0°C and 50°C (32°F and 122°F).

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards ANSI/NFPA 70 and Canadian

Electrical Code, Part I, C22.1. Be sure to use the proper overcurrent protection for the

installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended.

• The AC Mains tolerance of this equipment is +6/-10%

• Short-circuit backup protection and overcurrent protection is provided by the building installation.

• To reduce the risk of fire, connect only to a circuit provided branch circuit overcurrent protection

in accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical

Code, Part I, C22.1. Be sure to use maximum 20A overcurrent protection in accordance with

the plug/equipment rating, for the installation.

• The plugs on the power supply cords and appliance inlet serve as the disconnect devices. Make

sure the socket-outlets providing power to the PDU are easily accessible.

• This equipment is not suitable for use in locations where children are likely to be present.

1. Important Safety Instructions

• Only those who are properly trained or qualified to use this device should do so. Anyone who is

not trained or qualified should not use this device unless it is under the supervision of someone

who is properly trained or qualified to do so.

• Children must be supervised to ensure that they do not use the device as a toy.

• Never use the device if the cord and plug are damaged. If the device is not working properly or if

it has been dropped or damaged, take it to an authorized service center for inspection and

repair.

• If the power cord is damaged, it must be replaced by the manufacturer, its authorized service

agent or qualified personnel in order to avoid danger.

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVAT1,

PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET

Primary InputSecondary Input

Primary Input

Secondary Input

Unswitched

Outlets

PDUMH15HVAT

PDUMH15HVATNET

Primary Input

PDUMH20HVAT,

PDUMH20HVAT1,

PDUMH20HVATS,

PDUMNH20HVAT1,

PDUMH20HVATNET

Primary Input (208-240V Models)

2.1 Mounting the PDU

The PDU supports 1U Rack configurations.

Note: The user must determine the fitness of

hardware and procedures before mounting. The PDU

and included hardware are designed for common

rack and rack enclosure types and may not be

appropriate for all applications. Exact mounting

configurations may vary.

1U Rack Mounting: Attach the PDU to the

rack by inserting four user-supplied screws A

through the PDU mounting brackets B and

into the mounting holes of the rack rail as

shown.

2. Installation

2.2 Connecting the PDU

All PDU models include a primary and secondary AC power input (see diagram). The reference

table below lists each model’s primary and secondary inputs:

Model Primary Input Secondary Input

PDUMH15HVAT* IEC C14 inlet (detachable cord) IEC C14 inlet

PDUMH15HVATNET* IEC C14 inlet (detachable cord) IEC C14 inlet

PDUMH20HVAT1* IEC C20 inlet (detachable cord) IEC C20 inlet

PDUMH20HVATS* IEC C20 inlet (detachable cord) IEC C20 inlet

PDUMNH20HVAT1* IEC C20 inlet (detachable cord) IEC C20 inlet

PDUMN20HVAT* IEC C20 inlet (detachable cord) IEC C20 inlet

PDUMH20HVATNET* IEC C20 inlet (detachable cord) IEC C20 inlet

*PDU includes one C13 to C14 (PDUMH15HVAT/NET) or two C19 to C20 (PDUMH20HVAT, PDUMH20HVAT1,

PDUMH20HVATS, PDUMNH20HVAT1, PDUMH20HVATNET) interconnection cables for the two primary and

secondary inlets, which may be used to connect to upstream UPS sources. Alternately, the user can supply IEC

cables fitted with country-specific plugs.

Feature Set Overviews

Part Description

Outlet

Types Outlet Control

Outlet

LED

Indicator

Shipped

with SNMP

Slot

Shipped with

SNMP Card

Installed

PDUMH15HVAT C13 YES YES YES NO

PDUMH15HVATNET C13 YES YES YES YES

PDUMH20HVAT C13, C19 YES (C13 Only) YES YES NO

PDUMH20HVAT1 C13, C19 YES (C13 Only) YES YES NO

PDUMH20HVATNET C13, C19 YES (C13 Only) YES YES YES

PDUMNH20HVAT1 C13, C19 NO NO YES YES

PDUMH20HVATS C13, C19 NO NO NO NO

2.2.1 Connect Secondary Input

Cord to PDU:

Although the PDU will operate without connecting

the Secondary input cord, the Secondary input is

required for the PDU's Automatic Transfer Switch

function.

2. Installation

Primary InputSecondary Input

Primary Input

Secondary Input

Unswitched

Outlets

2.2.1

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVAT1,

PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET

Primary Input

Secondary Input

Unswitched

Outlets

Primary InputSecondary Input

PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS,

PDUMNH20HVAT1, PDUMH20HVATNET PDUMH15HVAT, PDUMH15HVATNET

2.2.4

Primary Input

Secondary Input

Unswitched

Outlets

PDUMH20HVAT,

PDUMH20HVAT1,

PDUMH20HVATS,

PDUMNH20HVAT1,

PDUMH20HVATNET

PDUMH15HVAT,

PDUMH15HVATNET

2.2.2

2. Installation

2.2.3 Selecting Input Voltage Range:

These models have two selectable nominal input voltage ranges: 200V-208V (“LO”) and

220V-240V (“HI”). Press the button next to the display to toggle the nominal voltage setting to the

desired “HI” or “LO” range. This setting adjusts the voltage ranges for the primary and secondary

inputs. The display will indicate “HI” or “LO” for five seconds.

2.2.4 Connect Equipment to PDU:

Do not exceed the load rating of the PDU. The total electrical current used by the PDU will be

displayed on the digital meter in amperes. Each outlet includes a green LED that illuminates when

the outlet is receiving AC power. (Select models only. See Feature Set Overviews chart above for

model-specific configurations.)

2.3 Networking the PDU (Models with SNMP Card

Installed only):

For network configuration instructions, please refer to the WEBCARDLX Owner’s Manual

included with this product.

2.2.2 Connect PDU Input Plugs:

(See the Configuration and Operation section for more information.) Connect the Primary input

plug A to a preferred source of grounded 230V AC power, such as a SmartOnline® UPS System.

The UPS system must not share a circuit with a heavy electrical load (such as an air conditioner or

refrigerator). Under normal operating conditions, the PDU will distribute AC power from the Primary

input source. Connect the Secondary input plug B to an alternative source of grounded 230V AC

power, such as a redundant SmartOnline UPS System. Do not plug the Secondary input into the

same power source as the Primary input. The PDU will distribute AC power from the Secondary

input only if the Primary input becomes unavailable.

Note: Immediately after the PDU is connected to live AC power, you may notice a series of soft clicking sounds

emitted by electrical relays within the PDU. The relays may also click occasionally during the operation of the

PDU. This is normal.

3 4 2 1

6 8

*Models with SNMP card installed only.

3. Features

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVATNET, PDUMH20HVAT1

PDUMH20HVATS, PDUMNH20HVAT1

5 6

2 14

6 8

4 2 1

3. Features

1 Primary Input

Models PDUMH15HVAT/NET: The C13-C14 cord is detachable.

Models PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET: The C19-C20 cord is detachable.

2 Secondary Input Inlet (detachable on all models)

Models PDUMH15HVAT/NET: The IEC-320-C14 inlet connects to the detachable Secondary

AC Input Power Cord.

Models PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET: The IEC-320-C20 inlet connects to the detachable Secondary AC Input

Power Cord.

3 Switched Outlets: During normal operation, the outlets distribute AC power to connected

equipment. These outlets may be switched On and Off via software control. When an outlet is

live, the associated LED illuminates.

4 Unswitched Outlets: These outlets receive power from either input source, but are not

individually switchable.

5 Factory Configuration Port: The port is reserved for configuration by factory authorized

personnel only. No user information is available. Connecting to this port may render the unit

inoperable and void its warranty.

6 Digital Load Meter (Ammeter): The total electrical current used by the connected equipment

is displayed on the digital meter in amperes.

Input Voltage Range Select Switch: The button to the lower left of the display may be used

to toggle between “HI” or “LO” voltage ranges. The display will indicate “HI” or “LO” for five

seconds. Press the switch once to display ranges. Press again within five seconds to change

setting. Setting can also be changed via PowerAlert (PDUMH15HVATNET and

PDUMH20HVATNET only).

IP Address Display (Models with SNMP card installed only): Press and hold the switch to

display the IP address of the SNMP card in the PDU.

7 Network Interface (Models with SNMP card installed only): Allows you to operate the PDU

as a managed network device, accessible via SNMP network management platform, web

browser, SSH or Telnet.

8 Input Source Indicator: When the PDU is connected to a live AC power source, the Primary or

Secondary input LED illuminates to indicate which source is supplying power to the outlets.

3. Features

Primary and Secondary AC Input Power Cord

(Models PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATNET,

PDUMH20HVATS, PDUMNH20HVAT1): Two C19-C20 cables are

included: one for Primary Input and one for Secondary Input.

Primary AC Input Power Cord

(Models PDUMH15HVAT, PDUMH15HVATNET): A C13-C14 cable

is included.

Plug Lock Inserts: Prevent accidental disconnection of C13-C14

or C19-C20 power cords.

Facility Circuit Facility Circuit

PDUMH15HVATNET

model shown. Outlets

may vary by model.

Critical Equipment

Loads

Secondary UPS Primary UPS

Primary Input Cord

Secondary Input Cord

Utility B Utility A

4. Configuration and Operation

4.1 Automatic Transfer Switch

When the Primary and Secondary inputs are both connected to Tripp Lite UPS Systems, the PDU

operates as an Automatic Transfer Switch, providing redundant input power for high availability

applications. Under normal operating conditions, the PDU will distribute power from the Primary

input source, switching to the Secondary input source under certain conditions. The PDU will switch

to the Primary source whenever it is “Good” according to the PDU input voltage definitions (see

section 4.1.2 for more information).

4.1.1 Preferred Configuration

The Automatic Transfer Switch function provides increased availability when the Primary and

Secondary inputs of the PDU are connected to separate Tripp Lite UPS Systems that are connected

to separate utility power sources. For maximum availability, Tripp Lite recommends using matching

SmartOnline UPS Systems with pure sine wave output for the Primary and Secondary input power

sources. The automatic transfer switch function will be compromised if the primary and secondary

inputs are connected to the same utility power source.

Warning: DO NOT connect the primary input to a line-interactive UPS, due to transfer time

issues, or to any source that does not supply a pure sine wave. Such sources may be used

to power the secondary input.

4. Configuration and Operation

4.1.2 Automatic Transfer Switch Source Selection

The PDU will power up if one of the input sources is greater than the minimum startup voltage. In

normal operation (after power-up), if the presently selected source (primary or secondary) degrades

to a lesser condition, the unit should switch to the alternate source, if that source is of better

quality. The unit prefers the primary source, and will always switch to it in the event that both

sources are of the same (fair or good) quality. If the present source is becoming bad and the

alternate source is at least fair, the unit will switch to the alternate source.

Nominal Voltage of PDU

High-Voltage Models

200-208V 220-240V

Minimum Startup Voltage 163V 163V

Good Voltage Range 172-241V 190-266V

Fair Voltage Range 144-171V 144-189V

Bad Voltage Range 0-143V 0-143V

4.1.3 Quick Test

Primary Input Active Secondary Input Active

After installing the PDU and connecting

equipment, you may test the Automatic

Transfer Switch function by temporarily shutting

down the UPS system connected to the

Primary AC input. When the Primary input UPS

is no longer supplying AC power, the PDU will

switch from the Primary input to the Secondary

input, and the Secondary input LED will

illuminate. When the Primary input UPS has

been restarted and resumes supplying AC

power, the PDU will switch back to the Primary

input.

Note: The primary and secondary inputs must be connected to separate sources of utility power. The automatic

transfer switch function will be compromised if the primary and secondary inputs are connected to the same

utility power source. Do not perform a test with equipment that must remain in productive operation. Any test

procedure must prepare for the contingency that the equipment may lose power. Do not test the PDU by

detaching power cords which are connected to live power sources, as this eliminates the connection to ground

and places your equipment at risk.

2-Year Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in

material and workmanship for a period of two (2) years from the date of initial purchase. If the product should prove

defective in material or workmanship within that period, Seller will repair or replace the product, at its sole discretion.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR

NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF

MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS

WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow

limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal

rights, and you may have other rights which vary from jurisdiction to jurisdiction.)

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe

for the use intended. Since individual applications are subject to great variation, the manufacturer makes no

representation or warranty as to the suitability or fitness of these devices for any specific application.

PRODUCT REGISTRATION

Visit tripplite.com/warranty today to register your new Tripp Lite product. You'll be automatically entered into a drawing for

a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense. The user must use shielded cables and

connectors with this product. Any changes or modifications to this product not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a

unique series number. The series number can be found on the product nameplate label, along with all required approval

markings and information. When requesting compliance information for this product, always refer to the series number.

The series number should not be confused with the marking name or model number of the product.

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and

illustrations may differ slightly from actual products.

5. Warranty and Product Registration

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

21-03-088 93-3E27_RevA

Manual del Propietario

PDU para Instalación en Rack

con Medidor Digital y Switch

de Transferencia Automática

Modelos: PDUMH15HVAT, PDUMH15HVATNET,

PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATNET,

PDUMH20HVATS, PDUMNH20HVAT1

Número de serie: AGAC7625

1. Instrucciones de Seguridad Importantes 14

2. Instalación 16

2.1 Instalación del PDU 16

2.2 Conexión del PDU 16

2.3 Conexión a Red del PDU 18

3. Características 19

4. Conﬁguración y Operación 22

4.1 Switch de Transferencia Automática 22

5. Garantía 24

English 1

Français 25

1111 W. 35th Street, Chicago, IL 60609 EE UU • tripplite.com/support

CONSERVE ESTAS INSTRUCCIONES

• Este manual contiene instrucciones y advertencias que deben seguirse

durante la instalación, operación y almacenamiento de este producto.

El incumplimiento de estas instrucciones y advertencias puede afectar

la garantía del producto.

• Advertencia: Este equipo cumple con lo exigido para la Clase A del

CISPR 32. En un entorno residencial, este equipo puede ocasionar una

interferencia de radio.

• El PDU proporciona la conveniencia de múltiples tomacorrientes, pero NO ofrece protección

contra sobretensión o ruido en la línea para los equipos conectados.

• El PDU está diseñado solo para uso en interiores en un entorno controlado lejos de humedad

excesiva, temperaturas extremas, contaminantes conductivos, polvo o luz del sol directa.

• Mantiene la temperatura ambiente interior entre 0 °C y 50 °C [32 °F y 122 °F].

• El PDU debe ser instalado solamente por un técnico calificado.

• No intente instalar el PDU en una superficie insegura o inestable.

• Instale de acuerdo con los estándares del Código Eléctrico Nacional ANSI / NFPA 70 y Código

Eléctrico Canadiense, Parte I, C22.1. Asegúrese de usar la protección adecuada contra sobre

corriente para la instalación, de conformidad con la especificación de la clavija y del equipo.

• Conecte el PDU a un tomacorriente que esté de acuerdo a los códigos locales de construcción y

que esté correctamente protegido contra corrientes excesivas, cortocircuitos y fallas de conexión

a tierra.

• Los tomacorrientes eléctricos que suministran energía al equipo deben instalarse próximos al

equipo y ser fácilmente accesibles.

• No conecte El PDU a un toma corriente que no esté a tierra o cables de extensión o

adaptadores que eliminen la conexión a tierra.

• Asegúrese de proporcionar un dispositivo local de desconexión, que sea fácilmente accesible, en

cualquier modelo que esté instalado permanentemente sin una clavija.

• Nunca intente instalar equipos eléctricos durante una tormenta eléctrica.

• El equipo individual conectado al PDU no debe consumir más corriente que la de la

especificación de cada tomacorriente individual del PDU.

• La carga total conectada al PDU no debe exceder la capacidad de carga máxima del PDU.

• No intente modificar el PDU, las clavijas de entrada o los cables de alimentación.

• No perfore ni intente abrir ninguna parte del gabinete del PDU. No contiene partes a las que el

usuario pueda dar servicio.

• No intente usar el PDU si se daña cualquier parte.

• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde

razonablemente se pueda esperar que la falla de este equipo cause la falla del equipo de

soporte de vida o afectar significativamente su seguridad o efectividad.

• La tolerancia de la alimentación de CA de este equipo es +6% / -10%.

• La protección de respaldo por corto circuito y la protección contra sobrecorriente es

proporcionada por la instalación del edificio.

• Para reducir el riesgo de incendio, conecte solamente a un circuito provisto de una protección

contra sobrecorrientes del circuito derivado según el Código Eléctrico Nacional, ANSI/NFPA 70 y

el Código Eléctrico Canadiense, Parte I, C22.1. Asegúrese de usar la protección máxima de 20A

contra sobrecorriente para la instalación, de conformidad con la especificación de la clavija y del

equipo.

1. Instrucciones de Seguridad Importantes

• Las clavijas en los cables de alimentación y la entrada del aparato sirven como los dispositivos

de desconexión. Asegúrese de que los tomacorrientes que alimentan al PDU sean fácilmente

accesibles.

• Este equipo no es adecuado para uso en ubicaciones donde es probable que estén presentes

niños.

• Este aparato no se destina para utilizarse por personas (incluyendo niños), cuyas capacidades

fisicas, sensoriales o mentales sean diferentes o estén reducidas, o carezcan de experiencia o

conocimiento, a menos que dichas personas reciban una supervisión o capacitación para el

funcionamiento del aparato por una persona responsable de su seguridad.

• Los ninos deben de supervisarse para asegurar que no empleen el aparato como juguete.

• Nunca utilize el aparato si el cable y la clavija están dañados; si no funciona correctamente o si

se ha caido o dañado, llévelo a un centro de servicio autorizado para que lo examinen y lo

reparen.

• Si el cordon de alimentación es dañado, éste debe sustituirse por el fabricante, por su agente

de servicio autorizado o por personal calificado con el fin de evitar un peligro.

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVAT1,

PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET

Primary InputSecondary Input

Primary Input

Secondary Input

Unswitched

Outlets

PDUMH15HVAT

PDUMH15HVATNET

Entrada

Primaria

Entrada Primaria

PDUMH20HVAT,

PDUMH20HVAT1,

PDUMH20HVATS,

PDUMNH20HVAT1,

PDUMH20HVATNET

Entrada Primaria (Modelos de 208V ~ 240V)

2.1 Instalar el PDU

el PDU es compatible con configuraciones de

1U de rack.

Nota: Antes de la instalación, el usuario debe

determinar la conveniencia de los accesorios y

procedimientos. El PDU y los accesorios incluidos

están diseñados para tipos comunes de racks y

gabinetes y pueden no ser apropiados para todas las

aplicaciones. Las configuraciones exactas de

instalación pueden variar.

Instalación en Rack de 1U: Fije el PDU al

rack insertando cuatro tornillos A

suministrados por el usuario a través de los

soportes de instalación del PDU B y en los

orificios de instalación del riel del rack, como

se muestra.

2. Instalación

2.2 Conectar el PDU

Todos los modelos de PDU incluyen una entrada de CA primaria y una secundaria (consulte el

diagrama). La tabla de referencia que aparece a continuación describe cada entrada primaria y

secundaria del modelo:

Modelo Entrada Primaria Entrada Secundaria

PDUMH15HVAT* Entrada C14 IEC (cable desprendible) Entrada C14 IEC

PDUMH15HVATNET* Entrada C14 IEC (cable desprendible) Entrada C14 IEC

PDUMH20HVAT1* Entrada C20 IEC (cable desprendible) Entrada C20 IEC

PDUMH20HVATS* Entrada C20 IEC (cable desprendible) Entrada C20 IEC

PDUMNH20HVAT1* Entrada C20 IEC (cable desprendible) Entrada C20 IEC

PDUMN20HVAT* Entrada C20 IEC (cable desprendible) Entrada C20 IEC

PDUMH20HVATNET* Entrada C20 IEC (cable desprendible) Entrada C20 IEC

El PDU incluye un cable de interconexión C13 a C14 (PDUMH15HVAT/NET) o dos cables de interconexión C19 a

C20 (PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS, PDUMNH20HVAT1, PDUMH20HVATNET) para las dos

entradas primaria y secundaria, que pueden usarse para conectar a las fuentes de UPS contra corriente. De

forma alternativa, el usuario puede suministrar cables IEC con clavijas específicas según el país.

Descripción General del Conjunto de Características

Descripción de la

Parte

Tipos de

Tomacor-

riente

Control de

Tomacor-

rientes

Indicador

LED de

Salida

Se Embarca

con Ranura

SNMP

Se Embarca con

Tarjeta SNMP

Instalada

PDUMH15HVAT C13 SÍ SÍ SÍ NO

PDUMH15HVATNET C13 SÍ SÍ SÍ SÍ

PDUMH20HVAT C13, C19 SÍ (C13

Solamente) SÍ SÍ NO

PDUMH20HVAT1 C13, C19 SÍ (C13

Solamente) SÍ SÍ NO

PDUMH20HVATNET C13, C19 SÍ (C13

Solamente) SÍ SÍ SÍ

PDUMNH20HVAT1 C13, C19 NO NO SÍ SÍ

PDUMH20HVATS C13, C19 NO NO NO NO

2.2.1 Conecte el Cable de Entrada

Secundaria al PDU:

Aunque el PDU funcione sin conectar el cable de

entrada secundaria, dicha entrada es necesaria

para la función del Switch de Transferencia

Automática del PDU.

2. Instalación

Primary InputSecondary Input

Primary Input

Secondary Input

Unswitched

Outlets

2.2.1

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVAT1,

PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET

Primary Input

Secondary Input

Unswitched

Outlets

Primary InputSecondary Input

PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS,

PDUMNH20HVAT1, PDUMH20HVATNET PDUMH15HVAT, PDUMH15HVATNET

2.2.4

Primary Input

Secondary Input

Unswitched

Outlets

PDUMH20HVAT,

PDUMH20HVAT1,

PDUMH20HVATS,

PDUMNH20HVAT1,

PDUMH20HVATNET

PDUMH15HVAT,

PDUMH15HVATNET

2.2.2

2. Instalación

2.2.3 Selección del Rango de Voltaje de Entrada:

Estos modelos tienen dos rangos de voltaje de entrada nominales: 200V ~ 208V (“LO”) y 220V ~

240V (“HI”). Presione el botón junto a la pantalla para cambiar la configuración de voltaje nominal

al rango deseado “HI” o “LO”. Esta configuración ajusta los rangos de voltaje para las entradas

primaria y secundaria. La pantalla indicará “HI” o “LO” durante cinco segundos.

2.2.4 Conecte el Equipo al PDU:

No exceda el valor nominal de carga del PDU. La corriente eléctrica total utilizada por el PDU

aparecerá en el medidor digital en amperes. Cada tomacorriente incluye un LED verde que se

ilumina cuando el tomacorriente recibe alimentación de CA. (Modelos selectos solamente. Para

configuraciones específicas del modelo, consulte la tabla anterior de vista general del conjunto de

características).

2.3 Conexión en Red del PDU (solamente modelos con

tarjeta SNMP instalada):

Para obtener instrucciones de configuración de red, consulte el Manual del Propietario de

la tarjeta WEBCARDLX incluido con este producto.

2.2.2 Conecte las Clavijas de Entrada del PDU:

(Para más información, consulte la sección de Configuración y Operación.) Conecte la clavija de

entrada Primaria A a una fuente preferente de alimentación de 230V CA conectada a tierra, como

un Sistema UPS SmartOnline™. El sistema UPS no debe compartir un circuito con una carga

eléctrica pesada (como un aire acondicionado o refrigerador). Bajo condiciones de operación

normales, la PDU distribuirá la alimentación de CA desde la fuente de entrada Primaria. Conecte la

clavija de entrada Secundaria B a una fuente alternativa de alimentación de 230V CA conectada

a tierra, como un sistema UPS redundante SmartOnline. No enchufe la entrada secundaria en la

misma fuente de alimentación que la entrada primaria. El PDU distribuirá la alimentación de CA

desde la entrada Secundaria solo si la entrada Primaria no está disponible.

Nota: Inmediatamente después de conectar el PDU a una alimentación de CA viva, puede observar una serie de

sonidos suaves emitidos por los relevadores eléctricos dentro del PDU. Los relevadores pueden emitir sonidos

ocasionalmente durante la operación del PDU. Esto es normal.

3 4 2 1

6 8

*Solamente modelos con tarjeta SNMP instalada.

3. Características

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVATNET, PDUMH20HVAT1

PDUMH20HVATS, PDUMNH20HVAT1

5 6

2 14

6 8

4 2 1

3. Características

1 Modelos de Entrada Primaria PDUMH15HVAT/NET: El cable C13-C14 es desprendible.

Modelos PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET: El cable C19-C20 es desprendible.

2 Entrada Secundaria (desprendible en todos los modelos) Modelos PDUMH15HVAT/NET:

La entrada IEC-320-C14 se conecta al cable de alimentación de CA Secundario desprendible.

Modelos PDUMH20HVAT, PDUMH20HVAT1, PDUMH20HVATS, PDUMNH20HVAT1,

PDUMH20HVATNET: La entrada IEC-320-C20 se conecta al cable de alimentación de CA

Secundario desprendible.

3 Tomacorrientes Controlables: Durante la operación normal, los tomacorrientes distribuyen

energía de CA al equipo conectado. Estos tomacorrientes pueden encenderse y apagarse

mediante control de software. Cuando un tomacorriente está encendido, el LED asociado se

ilumina.

4 Tomacorrientes no Controlables: Estos tomacorrientes reciben energía de cualquier fuente

de alimentación, pero no son controlables individualmente.

5 Puerto de Configuración de Fábrica: El puerto está reservado para configuración solamente

por personal autorizado de fábrica. No hay disponible información para el usuario. La conexión

a este puerto puede hacer que la unidad se vuelva inoperable y anular su garantía.

6 Medidor Digital de Carga (Amperímetro): La corriente eléctrica total usada por el equipo

conectado se muestra en el medidor digital en amperes.

Switch de Selección de Rango de Voltaje de Entrada: El botón en la parte inferior izquierda

de la pantalla puede usarse para cambiar entre los rangos de voltaje “HI” o “LO”. La pantalla

indicará “HI” o “LO” durante cinco segundos. Presione el switch una vez para mostrar los

rangos. Presione nuevamente en un lapso de cinco segundos para cambiar la configuración.

Las configuraciones también pueden cambiarse mediante PowerAlert (solo PDUMH15HVATNET

y PDUMH20HVATNET).

Pantalla de Dirección IP (Únicamente modelos con tarjeta SNMP instalada): Presione y

sostenga el switch para mostrar la dirección IP de la tarjeta SNMP en el PDU.

7 Interfaz de red Únicamente modelos con tarjeta SNMP instalada): Le permite operar el

PDU como un dispositivo de red administrado, accesible mediante plataforma de

administración de red SNMP, navegador Web, SSH o Telnet.

8 Indicador de Fuente de Entrada: Cuando el PDU está conectado a una fuente de

alimentación de CA viva, el LED de entrada Primaria o Secundaria se ilumina para indicar qué

fuente está suministrando energía a los tomacorrientes.

La page charge ...

Tripp Lite TRIPP-LITE PDUMH15HVAT Metered Rack-Mount PDU Le manuel du propriétaire

Marque: Tripp Lite

Modèle: TRIPP-LITE PDUMH15HVAT Metered Rack-Mount PDU

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

Tripp Lite TRIPP-LITE PDUMH15HVAT Metered Rack-Mount PDU Le manuel du propriétaire

Tripp Lite TRIPP-LITE PDUMH15HVAT Metered Rack-Mount PDU Le manuel du propriétaire

dans d''autres langues

Documents connexes