Ryobi RY141802 Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire

Ce manuel convient également à

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
ELECTRIC PRESSURE WASHER
LAVEUSE À PRESSION À ÉLECTRIQUE
LAVADORA DE PRESIÓN A ELÉCTRICA
RY141802
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
TABLE OF CONTENTS
Important Safety Instructions ............. 2
Specific Safety Rules ......................3-4
Symbols ...........................................5-6
Electrical ............................................. 7
Features ..............................................8
Assembly .........................................8-9
Operation .....................................10-13
Maintenance ................................13-14
Troubleshooting ...............................15
Parts Ordering and Service ...Back Page
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
TABLE DES MATIÈRES
Instructions importantes
concernant la sécurité........................2
Règles de sécurité particulières ......3-4
Symboles .........................................5-6
Caractéristiques électriques ............6-7
Caractéristiques ..............................7-8
Assemblage .....................................8-9
Utilisation .....................................10-13
Entretien ......................................13-14
Dépannage .......................................15
Commande de pièces et
réparation ......................... Páge arrière
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
ÍNDICE DE CONTENIDO
Instrucciones de seguridad
importantes ........................................ 2
Reglas de seguridad específicas ....3-4
Símbolos .........................................5-6
Aspectos eléctricos .........................6-7
Características ................................7-8
Armado ............................................8-9
Funcionamiento ...........................10-13
Mantenimiento .............................13-14
Solución de problemas ....................15
Pedidos de piezas y
servicio .......................... Pág. posterior
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner
toutes les figures mentionnées dans le manuel
d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el
manual del operador.
iii
Fig. 1 Fig. 2
A - Test button (bouton de test, botón de prueba)
B - Reset button (bouton de réinitialisation,
botón de reajuste)
AB
Fig. 3
A - Trigger handle (poignée de gâchete, mango del gatillo)
B - Trigger with lock-out (gâchette avec verouillage, gatillo con seguro)
C - Spray wand (lance de pulvérisation, tubo rociado)
D - On/off switch (commutateur marche / arrêt, interruptor de encendido)
E - High pressure hose outlet (prise tuyau haute pression, tomacorriente
manguera de alta presión)
F - Water intake (rise d’eau, entrada de agua)
G - Power cord (cordon d’alimentation, cable de alimentación)
H - Nozzle storage (rangement de buses, almacenamiento para boquilla)
I - High pressure hose and power cord storage strap (boyau haute pression
et courroie de rangement pour le cordon d’alimentation, manguera de
alta presión y correa de almacenamiento del cable de alimentación)
J - High pressure hose (tuyau haute pression, manguera de alta presión)
K - Turbo nozzle (buse de turbo, boquilla de turbo)
L - Nozzle (buse, boquilla)
M- Soap applicator (applicateur de savon, aplicador de jabón)
A - Pressure washer power cord (cordon d’alimentation de la laveuse à pression, cordón de corriente de
la lavadora de presión)
B - Drip loop (boucle d’égouttement, vuelta de goteo)
C - Extension cord (cordon prolongateurs, cordón de extensión)
A
A
B
C
D
F
E
G
H
I
J
K
M
L
B
C
iv
A - Threaded outlet (raccord fileté, conexión
roscada)
B - Collar (collier, casquillo)
C - High pressure hose (tuyau haute pression,
manguera de alta presión)
Fig. 5
Fig. 4
Fig. 7
Fig. 8
Fig. 9
A - Trigger handle (poignée à gâchette, mango
del gatillo)
B - Spray wand (lance de pulvérisation, tubo
rociado)
A - Screw (vis, tornillo)
B - Carrying handle (poignée de transport,
mango de transporte)
C - Screw hole (trou de vis, agujero de tornillo)
A
A
B
C
B
Fig. 6
A - Collar (collier, casquillo)
B - Inlet coupler (raccord d’entrée, acoplador de
entrada)
C - High pressure hose (tuyau haute pression,
manguera de alta presión)
A - Water intake (rise d’eau, entrada de agua)
B - Garden hose (tuyau d’arrosage, manguera de
jardín)
C - Screen (tamis, cedazo)
A - On/off switch (commutateur marche / arrêt,
interruptor de encendido)
A - Trigger (gâchette, gatillo)
B - Lock-out (verrouillage, seguro)
A - Spray wand (lance de pulvérisation, tubo
rociador)
B - Nozzle (buse, boquilla)
C - Turbo nozzle (buse de turbo, boquilla de
turbo)
D - Pull back the quick-connect collar (tirer la
bague à connexion rapide, tire del collar de
conexión rápida)
E - Push the nozzle into place (insérer en place la
buse, introduzca la boquilla en su lugar)
F - Push the collar forward (poussez en avant la
bague, empuje del collar adelante)
A
A
B
C
Fig. 11
A
B
C
B
A
A
CB
B
C
E
E
F
D
D
A
A
F
Fig. 10
v
A - Threaded top (bouchon vissé, parte superior roscada)
B - Rubber seal (joint de caoutchouc, sello de goma)
C - Paper seal (sceaux de papier, sello de papel)
D - Water intake (rise d’eau, entrada de agua)
E - Pump outlet (sortie de la pompe, orificio de descarga de la bomba)
F - Pump protector (protecteur de pompe, protector de bomba)
Fig. 12
Fig. 15
Fig. 16
Fig. 17
A - Straightened paper clip (trombone droit, clip
para papel abierto)
B - Nozzle (embout, boquilla)
A
B
A
B
A - Soap applicator (applicateur de savon,
aplicador de jabón)
B - Trigger handle (poignée de gâchete, mango
del gatillo)
Fig. 13
Fig. 14
C
B
A
D
A
F
E
2 — English
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire, and/or serious personal injury.
WARNING:
When using this product basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
THIS PRODUCT
To reduce the risk of injury, close supervision is
necessary when a product is used near children.
Be thoroughly familiar with controls. Know how to stop
the product and release pressure quickly.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate product
when you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Don’t overreach or stand on a ladder, rooftop, or other
unstable support. Keep proper footing and balance at
all times.
Follow the maintenance instructions specified in this
manual.
This product is provided with a ground fault
circuit interrupter built into the power cord plug. If
replacement of the plug or cord is needed, use only
identical replacement parts.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
SAVE THESE INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER
PROTECTION
This pressure washer is provided with a ground fault circuit
interrupter (GFCI) built into the plug of the power supply
cord. This device provides additional protection from the risk
of electric shock. Should replacement of the plug or cord
become necessary, use only identical replacement parts that
include GFCI protection.
EXTENSION CORDS
See Figure 1.
Use only extension cords that are intended for outdoor use.
These extension cords are identified by a marking “Acceptable
for use with outdoor appliances; store indoors while not in
use.” Use only extension cords having an electrical rating
not less than the rating of the product. Do not use damaged
extension cords. Examine extension cord before using and
replace if damaged. Do not abuse extension cord and do
not yank on any cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect the extension cord
from the receptacle before disconnecting the product from
the extension cord. Always plug the extension cord into a
GFCI protected outlet.
To avoid the possibility of the tool plug getting wet when
using an extension cord, arrange a “drip loop” in the cord
connecting the pressure washer to the extension cord. The
“drip loop” is that part of the cord below the level of the
connector which prevents water travelling along the cord
and coming in contact with the connection. If the plug does
get wet, DO NOT unplug the cord. Disconnect the fuse or
circuit breaker that supplies power to the tool, then unplug
and examine for presence of water in the connection.
WARNING: To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch plug with
wet hands.
SERVICING OF A DOUBLE-INSULATED
APPLIANCE
In a double-insulated product, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated product, nor should a means
for grounding be added to the product. Servicing a double-
insulated product requires extreme care and knowledge of
the system, and should be done only by qualified service
personnel. Replacement parts for a double insulated product
must be identical to the parts they replace. A double-insulated
product is marked with the words “DOUBLE INSULATION”
or “DOUBLE INSULATED.” The symbol may also be
marked on the product.
IMPORTANT SAFETY INSTRUCTIONS
3 — English
Use caution when positioning the pressure washer
for use. Warm air from the motor could cause discolored
spots on grass.
Know your product. Read the operator’s manual care-
fully. Learn the machine’s applications and limitations
as well as the specific potential hazards related to this
product.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Use right product. Don’t force product or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
Dress properly. Wear long pants and long sleeves. Do
not wear loose clothing, neckties, or jewelry. They can get
caught and draw you into moving parts. Rubber gloves
and nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
 Alwaysweareyeprotectionwithsideshieldsmarked
to comply with ANSI Z87.1. Following this rule will
reduce the risk of serious personal injury.
Use only recommended accessories. The use of
improper accessories may cause risk of injury.
Check damaged parts. Before further use of the product,
a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
Never leave product running unattended. Turn power
off. Don’t leave product until it comes to a complete stop.
Keep the motor free of grass, leaves, or grease to
reduce the chance of a fire hazard.
Follow manufacturer’s recommendations for safe
loading, unloading, transport, and storage of machine.
Keep product dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products, or any
solvents to clean product.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string
which can be thrown or become entangled in the
machine.
Do not use tool if switch does not turn it off. Have
switch replaced by an authorized service center.
Avoid dangerous environment. Don’t expose to rain.
Keep work area well lit.
Do not abuse the cord. Never use the cord to carry the
product or to disconnect the plug from an outlet. Keep
cord away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for the product. Receptacles are available having
built-in GFCI protection and may be used for this measure
of safety.
To reduce the risk of electric shock, this product has a
polarized plug (one blade is wider than the other) and
will require the use of a polarized extension cord. The
plug will fit into a polarized extension cord only one way. If
the plug does not fit fully into the extension cord, reverse
the plug. If the plug still does not fit, obtain a correct
polarized extension cord. A polarized extension cord will
require the use of a polarized wall outlet. This plug will
fit into the polarized wall outlet only one way. If the plug
does not fit fully into the wall outlet, reverse the plug. If
the plug still does not fit, contact a qualified electrician to
install the proper wall outlet. Do not change the equipment
plug, extension cord receptacle, or extension cord plug
in any way.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. A wire
gauge size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating.
WARNING: Use outdoor extension cords marked SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.
These cords are rated for outdoor use and reduce the risk
of electric shock.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil or
grease.
Never direct a water stream toward people or pets,
or any electrical device.
Before starting any cleaning operation, close doors
and windows. Clear the area to be cleaned of debris,
toys, outdoor furniture, or other objects that could create
a hazard.
SPECIFIC SAFETY RULES
4 — English
Make sure minimum clearance of 3 feet is maintained
from combustible materials.
Never spray close to the surface to be cleaned, as you
can damage the surface.
After stopping the motor, always pull the trigger on the
trigger handle to relieve stored pressure in the high
pressure hose. Failure to do so could result in serious
personal injury.
Ensure the high pressure hose is properly connected
before using the product.
Connect pressure washer only to an individual branch
circuit.
Hold the trigger handle securely with both hands.
Expect the trigger handle to move when the trigger is
pulled due to reaction forces. Failure to do so could cause
loss of control and injury to yourself and others.
For outdoor use only.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
product, loan them these instructions also.
Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions in this
product. These products can cause physical injuries to
the operator and irreversible damage to the machine.
WARNING: High pressure jets can be dangerous
if subject to misuse. The jet must not be directed at
persons, animals, electrical devices, or the machine itself.
Keep the motor away from flammables and other
hazardous materials.
Check bolts and nuts for looseness before each use. A
loose bolt or nut may cause serious motor problems.
Before storing, allow the motor to cool.
When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
ONLY use cold water.
Never pick up or carry a machine while the motor is
running.
Never start the machine if ice has formed in any part
of the equipment.
Keep guards in place and in working order. Never
operate the tool with any guard or cover removed. Make
sure all guards are operating properly before each use.
SPECIFIC SAFETY RULES
5 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations, and never direct
a water stream toward any electrical device.
Risk of Injection
To reduce the risk of injection or injury, never direct a water stream
towards people or pets or place any body part in the stream. Leak-
ing hoses and fittings are also capable of causing injection injury.
Do not hold hoses or fittings.
Risk of Explosion Do not spray flammable liquids. Flammable liquids and their vapors
are explosive and can cause severe burns or death.
Kickback To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock Do not use near electric power lines or receptacle outlets.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
6 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
7 — English
USE ONLY THIS SIZE EXTENSION CORD WHEN USING
THIS PRODUCT:
Cord Length Wire Size (A.W.G.)
25 ft. 14
50 ft. 12
100 ft. Not Allowed
NOTE: A.W.G. = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools, or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.
GROUND FAULT CIRCUIT INTERRUPTER
See Figure 2.
This unit is equipped with a Ground Fault Circuit Interrupter
(GFCI), which guards against the hazards of ground fault
currents. An example of ground fault current is the current
that would flow through a person who is using an appliance
with faulty insulation and, at the same time, is in contact
with an electrical ground such as a plumbing fixture, wet
floor, or earth.
GFCI plugs do not protect against short circuits, overloads,
or shocks.
NOTE: To ensure readiness for use, press the reset button
each time you connect the pressure washer to the power
supply.
The GFCI plug can be tested with the TEST and RESET
buttons.
To test:
Press the TEST button. You will hear a “click” sound and
the LED light will go out.
To restore power, press the RESET button. The LED light
will illuminate to indicate power has been restored.
Perform this test monthly to ensure proper operation of the
GFCI.
To reduce the risk of electric shock the supervisory
circuit must be operated before an appliance is
plugged into any receptacle on the device.
DOUBLE INSULATION
Double insulation is a concept in safety in electric power tools,
which eliminates the need for the usual three-wire grounded
power cord. All exposed metal parts are isolated from the
internal metal motor components with protecting insulation.
Double insulated products do not need to be grounded.
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the product’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should
be performed only by a qualified service technician. For
service, we suggest you return the product to your nearest
authorized service center for repair. Always use original
factory replacement parts when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be
connected to a power supply that is nominal 120V/60Hz
AC (typical U.S. household circuit). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, possibly
resulting in overheating, loss of power, and/or circuit
breaker or GFCI tripping. Use the chart to determine the
minimum wire size required in an extension cord. Only round
jacketed cords listed by Underwriter’s Laboratories (UL)
should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during
use. Make a knot, then connect the plug end of the power
cord into the receptacle end of the extension cord. This
method can also be used to tie two extension cords together.
ELECTRICAL
8 — English
PRODUCT SPECIFICATIONS
Maximum Pounds Per Square Inch* ........................................................................................................................1,800 psi
Maximum Gallons Per Minute ...................................................................................................................................1.2 GPM
Input ...........................................................................................................................nominal 120V/60Hz AC only, 13 Amps
*Maximum rating when tested to PWMA standard PW101.
KNOW YOUR PRESSURE WASHER
See Figure 3.
The safe use of this product requires an understanding of the
information on the product and in this operators manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
CARRYING HANDLE
The pressure washer has a carrying handle for easy transport.
SOAP APPLICATOR
The pressure washer comes with a soap applicator which
connects directly to the trigger handle and applies detergent
quickly and easily to your cleaning project.
GFCI PLUG
The pressure washer is equipped with a GFCI plug to guard
against the hazards of ground fault currents. This plug does
not protect against short circuits, overloads, or shocks.
HOSE STORAGE
Once the high pressure hose is rolled, hang it on the side
of the machine along with the power cord using the hook-
and-loop strap to secure in place.
ON/OFF SWITCH
This switch turns the pressure washer on and off.
POWER CORD STORAGE
Once the power cord is rolled, hang it on the right side of
the machine along with the high pressure hose using the
hook-and-loop strap to secure in place.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides
added control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK-OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock-out provides protection against
unauthorized use.
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the Packing
List are included.
WARNING:
Do not use this product if any parts in the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Electric Pressure Washer
Carrying Handle
20 ft. Ultra Thin High Pressure Hose
Trigger Handle
Spray Wand
Nozzles (15º, Turbo)
Soap Applicator
Screws
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
FEATURES
ASSEMBLY
9 — English
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
INSTALLING THE CARRYING HANDLE
See Figure 4.
CAUTION:
Be careful to avoid pinching your fingers or hands when
installing the handle onto the housing.
Position the carrying handle over the pressure washer
with the holes aligned as shown.
Install screws and tighten securely.
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 5.
 Push the end of the spray wand into the trigger handle
and rotate clockwise to secure.
Pull on the spray wand to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE TO
THE TRIGGER HANDLE
See Figure 6.
Screw the collar on the high pressure hose into the trigger
handle inlet coupler by turning the hose collar clockwise.
Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE TO
THE PUMP
See Figure 7.
Completely uncoil and straighten the high pressure hose
to prevent kinks.
NOTE: See Using the High Pressure Hose in Operation
for more information about using the high pressure hose.
Align the collar to the threaded outlet on the pump.
Install the high pressure hose collar onto the threaded
outlet.
Turn the collar clockwise to tighten the hose securely to
the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 8.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water
supply to prevent the feedback of chemicals into the
drinking water supply. Direct connection through a
receiver tank or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet of unrestricted
hose between the pressure washer intake and the hose
faucet or shut off valve (such as a “Y” shut off connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
ASSEMBLY
10 — English
WARNING:
Do not allow familiarity with the product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to follow these instructions
could result in serious injury, electric shock, or death.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or an
authorized service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills,
playground equipment, etc.
*Always test in an inconspicuous area first.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 9.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the motor:
Connect the garden hose.
NOTE: Make sure the pressure washer’s water intake
screen is in place and unclogged before connecting
garden hose.
Turn on the garden hose then pull the trigger to relieve air
pressure; hold the trigger until a steady stream of water
appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the motor:
With the on/off switch in the OFF position, connect the
pressure washer to the power supply.
NOTE: If using an extension cord, make sure to arrange
a drip loop as described on page 2.
WARNING:
To reduce the risk of electrocution, keep all connections
dry and off the ground. Do not touch plug with wet hands.
Press the reset button on the pressure washer’s plug to
make sure the unit is ready for operation.
Press switch ON to start the motor.
To stop the motor:
Press switch OFF to stop the motor
Pull trigger to release water pressure.
NOTE: The pressure washer may be on and the system
may have pressure even when the pump and/or motor
cannot be heard running. Always use caution around the
pressure washer.
OPERATION
11 — English
USING THE TRIGGER HANDLE
See Figure 10.
WARNING:
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
Push up on the lock out until it clicks into the slot.
To disengage the lock out:
Push the lock out down and into its original position.
Start with the nozzle 1–2 ft. away from the cleaning surface
and carefully approach the surface just until the desired
level of cleaning is achieved. If the spray is too close it can
damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 11.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more information
about which nozzle to choose.
WARNING:
NEVER remove nozzles without first turning off the motor,
disconnecting the power supply, relieving the water
pressure in the trigger handle, and locking the lock out
on the trigger handle. NEVER point the nozzle at your
face or at others. The quick-connect feature contains
small springs that could eject the nozzle with some force.
Failure to follow these instructions could result in an eye
injury or other serious personal injury.
To connect a nozzle to the spray wand:
Turn off the pressure washer, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back the quick-connect collar.
OPERATION
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
Turbo Nozzle 15º Soap Applicator
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
Recommended Nozzle Use With Caution for Certain Applications
12 — English
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
Turn off the pressure washer, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back and hold the quick-connect collar.
Remove the nozzle by pulling it from the quick-connect
collar. Place nozzle in the nozzle storage area on the top
of the machine.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high
pressure hose prior to and during each use and do
not allow it to become kinked. The high pressure hose
features an outer covering that provides strength to the
hose. If the outer covering becomes damaged, stop using
the hose and replace it immediately. A kinked or damaged
hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 12 - 13.
As sold, this unit is designed for use with “downstream”
pressure washer detergents. To convert for use with
“upstream” detergents, contact customer service or an
authorized customer service center for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
To connect the soap applicator to the trigger handle:
Turn off the pressure washer, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Rotate the spray wand counterclockwise to remove it
from the trigger handle.
Fill soap applicator with soap.
 Push the end of the soap applicator into the trigger handle
and rotate clockwise to secure.
Pull on the soap applicator to be certain it is properly
secured.
Connect unit to power supply and turn the pressure
washer on.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
To disconnect the soap applicator from the spray wand
once the cleaning job is complete:
Turn off the pressure washer, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Rotate the soap applicator counterclockwise to remove
it from the trigger handle.
Rinse soap applicator with clear water.
NOTE: Shutting off the motor will not relieve pressure in the
system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the soap applicator, if installed.
Reconnect the spray wand.
Select the right nozzle for the job. See the chart on the
previous page for selecting the appropriate nozzle.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USING PUMP PROTECTOR
See Figure 14.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should
OPERATION
13 — English
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off motor, wait for all moving parts to stop,
disconnect unit from power supply, and pull trigger to
release water pressure. Failure to follow these instructions
can result in serious personal injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or an
authorized service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which could result in serious personal
injury.
PUMP LUBRICATION
The pump on this unit is lubricated with a sufficient amount
of high grade lubricant for the life of the unit under normal
operating conditions. Therefore, no further lubrication is
required.
POWER SUPPLY CORD REPLACEMENT
If replacement of the power supply cord is necessary, this
must be done by an authorized service center in order to
avoid a safety hazard.
NOZZLE MAINTENANCE
See Figure 15.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
MAINTENANCE
OPERATION
be added to the unit after every use and before storage.
Pump protector can be purchased at the retailer where you
purchased your pressure washer, or by calling customer
service.
The instructions that follow are typical for adding pump
protector but you should always verify the specific
instructions provided by the manufacturer of the pump
protector used.
Turn off the pressure washer motor, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Disconnect garden hose and high pressure hose.
Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
Squeeze bottle to inject contents into pump.
Pump is protected when the protector fluid exits the pump
outlet.
MOVING THE PRESSURE WASHER
Turn the pressure washer off. Point nozzle in a safe
direction and pull trigger to release water pressure.
Disconnect pressure washer from power supply.
Using the carrying handle, get a firm grasp of the unit.
Lift the unit into a safe and comfortable carrying position.
Move machine to the desired location.
14 — English
MAINTENANCE
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Unplug the pressure washer.
Remove the nozzle from the spray wand.
WARNING:
NEVER remove nozzles without first turning off the motor,
relieving the water pressure in the trigger handle, and
locking the lock out on the trigger handle. NEVER point
the nozzle at your face or at others. The quick-connect
feature contains small springs that could eject the nozzle
with some force. Failure to follow these instructions could
result in an eye injury or other serious personal injury.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a straightened
paper clip or fine needle (not included).
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Reinstall the garden hose and connect the unit to the
power supply.
PUMP MAINTENANCE
Routinely make a visual inspection of the pump. If you notice
any leaking of lubricant around the pump seals, take the
pressure washer to an authorized service center for repair.
There are no user serviceable parts to the pressure washer
pump. Any attempt to service or alter the pump may dam-
age the pressure washer and void your product warranty.
STORING THE PRESSURE WASHER
See Figures 16 - 17.
NOTE: Regular use of pump protector will give you better
performance of the unit and increase the life of the pump.
Store in a dry, covered area where the weather can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses and the pump before storing.
Make sure the on/off switch is in the OFF position.
Unplug the pressure washer and store the power cord
using the hook-and-loop strap.
Disconnect both the high pressure hose and the garden
hose from the pump.
Neatly coil the high pressure hose and store with hook-
and-loop strap.
Tilt the unit as shown to allow any remaining water in the
pump to drain from the water outlet.
NOTICE:
If the location where your pressure washer is stored will
fall below 32°F, the use of a pump protector is required
before storing to prevent freeze damage. Freeze damage
will void your warranty.
Turn the spray wand counterclockwise to remove it from
the trigger handle. Store the unassembled spray wand
and trigger handle in their storage areas.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
This product has a Three-year Limited Warranty for personal,
family, or household use (90 days for business or commercial use).
For warranty details, visit www.ryobitools.com
or call (toll free) 1-800-525-2579.
15 — English
PROBLEM POSSIBLE CAUSE SOLUTION
Pressure washer does not start
when trigger is depressed
Power cord not connected to power
source
The on/off switch is in the OFF
position (O)
GFCI is tripped
House/shop circuit breaker is tripped
Water pressure in hose
Connect the power cord to a live
120V AC, 60 Hz AC receptacle.
Put the on/off switch in the ON
position (I).
Press reset button on the GFCI
plug.
Reset house/shop breaker. Make
sure pressure washer is connected
to an individual branch circuit only. If
using an extension cord, make sure it
is heavy enough to carry the current
of the pressure washer.
Squeeze trigger to relieve water
pressure.
Pump doesn’t produce pressure Inadequate water supply
Trigger handle leaks
Nozzle is clogged
Pump is faulty
Air in line
Water inlet filter is clogged or dirty
Provide adequate water flow.
Check connections and/or replace
trigger handle.
Clean nozzle.
Contact authorized service center.
Squeeze trigger on trigger handle to
remove air from line.
Remove the water inlet filter, rinse
with warm water, then replace in unit.
Machine doesn’t reach high
pressure
Diameter of garden hose is too small
Water supply is restricted
Not enough inlet water
Hose is leaking
Kink in hose
Replace with 3/4 in. garden hose.
Check garden hose for kinks, leaks,
and blockages.
Open water source full force.
Replace hose.
Eliminate kinks in hose.
No detergent Soap applicator is not properly installed
Water supply is inadequate or
clogged
Wrong nozzle is attached
Make sure soap applicator is installed
correctly.
Check garden hose for kinks, leaks
and blockages.
Attach soap applicator.
Wand leaks O-ring needs replacing Replace o-ring. If this does not
correct the problem, contact
your authorized service center to
purchase a new wand.
TROUBLESHOOTING
2 — Français
AVERTISSEMENT :
Lire attentivement toutes les instructions. Le non-
respect de toutes les instructions ci-dessous peut
entraîner un choc électrique, un incendie et/ou des
blessures graves.
AVERTISSEMENT :
Lors de l’utilisation de ce produit, toujours suivre les
consignes de base, notamment :
LIRE TOUTES LES INSTRUCTIONS AVANT
D’UTILISER CE PRODUIT
Pour réduire les risques de blessures, porter une
attention particulière lorsque le produit est utilisé en
présence d’enfants.
Se familiariser complètement avec les commandes.
Veiller à savoir arrêter la machine et relâcher la pression
rapidement.
Rester vigilant et garder le contrôle. Se montrer attentif
et faire preuve de bon sens. Ne pas utiliser le produit en
état de fatigue. Ne pas se presser.
Ne pas utiliser ce produit sous l’influence de l’alcool,
de drogues ou de médicaments.
Ne laisser personne approcher la zone de travail,
particulièrement les petits enfants et les animaux
domestiques.
Ne pas travailler hors de portée ou se tenir sur
une échelle, un échafaudage, un toit ou un surface
instable. Toujours se tenir bien campé et en équilibre.
Suivre les instructions d’entretien décrites dans le
présent manuel.
Ce produit est fourni avec un disjoncteur de fuite à la
terre intégré dans la fiche du cordon d’alimentation.
S’il est nécessaire de procéder au remplacement de la
fiche ou du cordon, utiliser exclusivement des pièces
identiques à celles d’origine.
AVERTISSEMENT : Risque d’injection ou de blessures –
ne pas diriger le jet directement vers quelqu’un.
CONSERVER CES INSTRUCTIONS
PROTECTION D’UN DISJONCTEUR DE FUITE
À LA TERRE
Cette laveuse à pression est fournie avec un disjoncteur de
fuite à la terre intégré dans la fiche du cordon d’alimentation.
Ce dispositif offre une protection supplémentaire contre les
décharges électriques. S’il est nécessaire de procéder au
remplacement de la fiche ou du cordon, utiliser exclusivement
des pièces identiques à celles d’origine qui incluent un
disjoncteur de fuite à la terre.
CORDONS PROLONGATEURS
Voir la figure 1.
Utiliser uniquement des cordons prolongateurs conçus
pour l’extérieur. Ces cordons prolongateurs sont
étiquetés « Compatibles avec les appareils extérieurs;
entreposer à l’intérieur lorsque le produit n’est pas utilisé ».
Utiliser uniquement des cordons prolongateurs dont
les caractéristiques électriques ne sont pas inférieures
à la puissance du produit. Ne pas utiliser des cordons
prolongateurs endommagés. Examiner le cordon prolongateur
avant de l’utiliser et le remplacer s’il est endommagé. Ne pas
malmener les cordons prolongateurs ni tirer d’un coup sec
dessus pour les débrancher. Garder le cordon à l’écart de
la chaleur et des rebords tranchants. Toujours débrancher
le cordon prolongateur de la prise de courant avant de
débrancher le produit du cordon prolongateur. Toujours
brancher le cordon prolongateur dans une prise protégée
par un disjoncteur de fuite de terre.
Pour éviter que la fiche de l’outil ne se mouille au moment
d’utiliser un cordon prolongateur, installer une « boucle
d’égouttement » sur le cordon qui relie la laveuse à pression
au cordon prolongateur. La « boucle d’égouttement » est la
partie du cordon située sous le connecteur qui empêche l’eau
de suivre le cordon et d’entrer en contact avec la prise. Si la
fiche est mouillée, NE PAS débrancher le cordon. Débrancher
le fusible ou le disjoncteur qui alimente l’outil, puis débrancher
ce dernier en vérifiant si de l’eau s’est infiltrée dans la prise.
AVERTISSEMENT : Pour réduire le risque d’électrocution,
garder toutes les connexions au sec et au-dessus du sol.
Ne pas manipuler la fiche avec les mains mouillées.
LA RÉPARATION D’UN APPAREIL À DOUBLE
ISOLATION
Le produit à double isolation comprend deux systèmes
d’isolation au lieu d’un système de mise à la terre. Aucun
appareil à double isolation ne comprend et ne requiert de
dispositif de mise à la terre. La réparation de ce produit
exige des précautions extrêmes et une bonne connaissance
du système; c’est pourquoi elle doit être confiée à un
technicien qualifié. Utiliser exclusivement des pièces de
remplacement identiques à celles d’origine. Les mots
« DOUBLE ISOLATION » sont indiqués sur les outils à double
isolation. Le symbole peut également être indiqué sur le
produit.
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Ryobi RY141802 Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
Ce manuel convient également à