C-LITE C-LITE C-CP-C-SQ Square LED Canopy Light Manuel utilisateur

Marque: C-LITE

Modèle: C-LITE C-CP-C-SQ Square LED Canopy Light

Taper: Manuel utilisateur

Ce manuel convient également à

C-CP-C-SQ Square LED Canopy Light

Document: LPN00473X0001A2_B Date: 4-25-2022

Created By: TMT

INSTALLATION INSTRUCTIONS

C-CP-C-SQ Series

http://lighting.cree.com/warranty | 1-800-236-6800

CAUTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety

precautions should always be followed including the

following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before

installation.

DANGER – Risque de choc – Couper l’alimentation

avant l’installation.

2. This luminaire must be installed in accordance with the

NEC or your local electrical code. If you are not familiar

with these codes and requirements, consult a qualied

electrician.

Ce produit doit être installé conformément à NEC ou votre

code électrique local. Si vous n’êtes pas familier avec ces

codes et ces exigences, veuillez contacter un électricien

qualié.

3. Suitable for wet locations.

Convient aux emplacements mouilles.

4. Covered ceiling mount only.

Installation sur plafond couvert seulement.

5. MIN. 75C SUPPLY CONDUCTORS.

LES FILS D’ALIMENTATION 75C MIN.

6. Make certain power is OFF before starting installation or

attempting any maintenance.

7. Do not recess the xture.

8. For supply wire temperature rating, refer to xture label.

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

1. Remove the four screws attaching the lens diuser to the xture

and set the screws and lens aside.

2. Remove the screws attaching the reector to the housing and set

aside.

3. Remove ¾” plug from back for wiring access.

4. Fixture is best mounted by drilling holes in the four corners of the

housing. Holes should be drilled from the outside of the casting

through the centers of each of the (4) circular ribbed mounting

supports in the corners of the housing. Make sure metal chips are

cleaned from inside housing after drilling. Fixture is to be secured

to the mounting surface using mounting hardware (supplied

by others) appropriate for the mounting surface. A high grade

caulking material, such as silicone rubber, should be used around

all the holes to ensure a watertight enclosure.

NOTE: Fixture can also be pendant mounted by threading the

customer supplied pendant into the ¾” mounting hole on the top

of the xture. If using center conduit hole for pendant the wireway

MUST be lled with a high grade of silicone supplied by customer

to prevent water from entering xture through the pendant. In

addition, Teon tape should be used on conduit threads.

5. Route the incoming power and ground leads through the hole

located in the center of the back of the xture and through the

opening on the side of the LED mounting pad.

6. Complete the wiring to the incoming power and ground (refer to

“Fixture Wiring” section).

7. Replace the reector and lens diuser. Note: Make sure no wires

are pinched when replacing parts. Do not overtighten lens screws

to prevent damage to lens.

DO NOT TOUCH THE LEDs OR WIRES COMING

FROM CIRCUIT BOARD DURING THE INSTALLATION

PROCESS. DAMAGE MAY OCCUR.

1. Remove the four screws attaching the lens diuser to the xture

and set the screws and lens aside.

2. Remove the screws attaching the reector to the housing and set

aside.

3. Remove 1/2” plug from direction you intend to feed conduit. Teon

tape should be used on conduit threads to prevent water entry.

NOTE: The (2) screws on either side of the 1/2" plug should not

be removed during installation. See Figure 1.

4. Fixture is best mounted by drilling holes in the four corners of the

housing. Holes should be drilled from the outside of the casting

through the centers of each of the (4) circular ribbed mounting

supports in the corners of the housing. Make sure metal chips are

cleaned from inside housing after drilling. Fixture is to be secured

to the mounting surface using mounting hardware (supplied

by others) appropriate for the mounting surface. A high grade

caulking material, such as silicone rubber, should be used around

all the holes to ensure a watertight enclosure.

5. Complete the wiring to the incoming power and ground (refer to

“Fixture Wiring” section).

6. Replace the reector and lens diuser. Note: Make sure no wires

are pinched when replacing parts. Do not overtighten lens screws

to prevent damage to lens.

MOUNTING USING ½” PLUGS ON THE SIDE

FIGURE 1 Do NOT Remove These Screws During

Installation

MOUNTING USING ¾" PLUG IN THE BACK

Document: LPN00473X0001A2_B Date: 4-25-2022

Created By: TMT

INSTALLATION INSTRUCTIONS

C-CP-C-SQ Series

http://lighting.cree.com/warranty | 1-800-236-6800

CAUTION: Changes or modifications not expressly approved could

void your authority to use this equipment.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

CAN ICES-005 (A)/NMB-005 (A)

FCC NOTICE

Fixture is equipped with universal volt driver 120-277V

(ie. 120V, 208V, 240V or 277V)

PHASE TO NEUTRAL WIRING 120/277V

1. Connect supply ground to fixture ground (green) lead.

2. Connect supply common to fixture neutral (white) lead.

3. Connect supply Vin to fixture hot (black) lead.

Tuck all wires carefully into wiring chamber ensuring that no wires

are pinched.

PHASE TO PHASE WIRING 208/240V

1. Connect supply ground to fixture ground (green) lead.

2. Connect supply L1 (Hot) to fixture neutral (white) lead.

3. Connect supply L2 (Hot) to fixture hot (black) lead.

Tuck all wires carefully into wiring chamber ensuring that no wires

are pinched.

DIMMING

1. Grey or pink (-) and violet (+) leads are for 0-10V dim-

ming systems. Cap off if not used.

2. For dimming connections, use Class 1 wiring methods.

ELECTRICAL CONNECTIONS

Documento: LPN00473X0001A2_B Fecha: 4-25-2022

Creado por: TMT

INSTRUCCIONES DE INSTALACIÓN

Serie C-CP-C-SQ

http://lighting.cree.com/warranty | 1-800-236-6800

PRECAUCIONES

MEDIDAS DE SEGURIDAD

IMPORTANTES

Al usar equipos eléctricos, siempre se deben seguir

medidas de seguridad básicas, incluidas las siguientes:

LEA Y SIGA TODAS LAS

INSTRUCCIONES DE SEGURIDAD

1. PELIGRO: Riesgo de descarga eléctrica. Desconecte la

alimentación eléctrica antes de la instalación.

DANGER – Risque de choc – Couper l’alimentation

avant l’installation.

2. Esta luminaria debe instalarse de acuerdo con el Código

Nacional Eléctrico (NEC, por sus siglas en inglés) o el

código eléctrico local. Si no está familiarizado con estos

códigos y requisitos, consulte a un electricista caliﬁ cado.

Ce produit doit être installé conformément à NEC ou

votre code électrique local. Si vous n’êtes pas familier

avec ces codes et ces exigences, veuillez contacter un

électricien qualiﬁ é.

3. Adecuada para ubicaciones húmedas.

Convient aux emplacements mouilles.

4. Montaje en techo cubierto únicamente.

Installation sur plafond couvert seulement.

5. CABLES DE ALIMENTACIÓN DE MÍNIMO 60 °C.

LES FILS D’ALIMENTATION 75C MIN.

6. Asegúrese de que la alimentación esté APAGADA

antes de comenzar la instalación o de intentar cualquier

mantenimiento.

7. No empotre la luminaria.

8. Para ver la clasiﬁ cación de temperatura de los cables de

alimentación, consulte la etiqueta de la luminaria.

CONSERVE ESTAS

INSTRUCCIONES PARA

CONSULTAS POSTERIORES

1. Retire los cuatro tornillos que sujetan el difusor del lente a la

luminaria y ponga a un lado los tornillos y el lente.

2. Retire los tornillos que sujetan el reﬂ ector a la carcasa y póngalos

a un lado.

3. Retire el tapón de 3/4” de la parte posterior para acceso del cableado.

4. La luminaria se monta mejor perforando agujeros en las cuatro

esquinas de la carcasa. Se deben taladrar oriﬁ cios desde el exterior

de la fundición a través de los centros de cada uno de los (4)

soportes de montaje con nervaduras circulares en las esquinas de

la carcasa. Asegúrese de limpiar las virutas de metal del interior de

la carcasa después de taladrar. La luminaria se debe asegurar a la

superﬁ cie de montaje utilizando hardware de montaje (suministrado

por otros) apropiado para la superﬁ cie de montaje. Se debe usar

un material de calafateo de alta calidad, como caucho de silicona,

alrededor de todos los oriﬁ cios para garantizar un recinto hermético.

NOTA: La luminaria también se montar en colgante, roscando el

colgante suministrado por el cliente entre el oriﬁ cio de montaje de 3/4”

en la parte superior de la luminaria. Si se usa el oriﬁ cio de conducto

central para el colgante, el conducto de los cables se DEBE llenar con

goma de silicón de alto grado suministrada por el cliente para evitar

que entre agua a la luminaria a través del colgante. Además, se debe

usar cinta de Teﬂ on en las roscas del conducto.

5. Guíe los cables de alimentación y de tierra a través del oriﬁ cio

ubicado en el centro de la parte posterior de la luminaria y a través

de la abertura en el costado de la almohadilla de montaje de LED.

6. Realice el cableado a la fuente de alimentación y la conexión

a tierra (consulte la sección “Cableado de la luminaria”).

7. Vuelva a instalar el reﬂ ector y el difusor del lente. Nota: Asegúrese

de no pellizcar ningún cable al volver a instalar las piezas.

No apriete excesivamente los tornillos del lente para evitar daños.

DURANTE EL PROCESO DE INSTALACIÓN, NO

TOQUE LOS LED NI LOS CABLES QUE SALEN DE LA

TARJETA DE CIRCUITOS. PUEDEN OCURRIR DAÑOS.

1. Retire los cuatro tornillos que sujetan el difusor del lente a la

luminaria y ponga a un lado los tornillos y el lente.

2. Retire los tornillos que sujetan el reﬂ ector a la carcasa y póngalos

a un lado.

3. Retire el tapón de 1/2” desde la dirección que desea alimentar el

conducto. Se debe usar cinta de Teﬂ on en las roscas del conducto

para evitar la entrada de agua.

NOTA: Durante la instalación, no se deben retirar los 2 tornillos en

los dos extremos del tapón de 1/2”. Ver Figura 1.