Luxpro PSD011Ba Manuel utilisateur

Marque: Luxpro

Modèle: PSD011Ba

Catégorie: Thermostats

Taper: Manuel utilisateur

Thank you for your confidence in our product. You should become fully

acquainted with this thermostat before installing it for usage. Follow the

installation procedures carefully, and one step at a time. This will save you

time and minimize the chance of damaging either the thermostat or the

systems that it controls. These instructions may contain information

beyond that required for your particular installation. Please save these

instructions for future reference.

• The single-stage PSD011Ba thermostat can be used with most 24 volt,

1 stage heat and/or 1 stage cool: gas, oil, or electric heating and air

conditioning systems, Millivolt systems, or single-stage heat pumps.

• The multi-stage PSD022Ba thermostat can be used with most 24 volt,

2 stage heat and/or 2 stage cool: gas, oil, or electric heating and air

conditioning systems, Millivolt systems, or single-stage heat pumps.

• These thermostats cannot be used to control 3-wire zone valves, multi-

stage heat pumps, or 120/240 volt (line voltage) heating or cooling

systems. Ask your dealer for other LUXPRO thermostats to control those

systems.

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING

INSTALLATION.

TOOLS REQUIRED:

• #1 Phillips screwdriver (small - medium)

• Drill with 3/16-in. (4.8mm) drill bit

• Wire stripper/cutter

THERMOSTAT LOCATION:

On replacement installations, mount the new thermostat in place of the old

one unless the conditions listed below suggest otherwise. On new instal-

lations, follow the guidelines listed below.

1. Locate the thermostat on an inside wall, at about 5 ft. (1.5m) above the

floor, and in a room that is used often.

2. Do not install it where there are unusual heating conditions, such as:

direct sunlight, near a lamp, television, radiator, register, fireplace, on a

wall opposite a stove, or that carries hot water pipes.

3. Do not locate in unusual cooling conditions, such as: on a wall

separating an unheated room, or in a draft from a stairwell, door, or

window.

4. Do not locate where air circulation is poor, such as: in a corner or

alcove, or behind an open door.

5. Do not locate in a damp area. This can lead to corrosion that may

shorten thermostat life.

6. Do not install the unit until all construction work and painting has been

completed.

REMOVING THE OLD THERMOSTAT:

1. Switch OFF the electricity to both the furnace and air conditioner; then

proceed with the following:

2. Remove cover from old thermostat. Most are snap-on types and simply

pull off, some have screws on the sides, and these must be loosened

first.

3. Take note of the letters printed near the wire terminals. Attach labels

(enclosed) to each wire for identification by terminal letter, not color.

4. Make sure the wires do not fall back inside the wall. Remove and label

one wire at a time, and do not allow the wires to touch each other or any

parts of the thermostat.

5. Loosen all screws on the old thermostat and/or base, and remove it from

the wall.

MOUNTING THE NEW THERMOSTAT:

1. Strip insulation leaving 3/8 in. (9.5mm) of bare wire on the ends and

clean off any corrosion present.

2. Fill the wall opening with non-combustible insulation to prevent drafts

from affecting the thermostat while in use.

3. Pull your new thermostat apart by applying pressure to the thumb tab on

the bottom edge of the unit. While pressure is being applied to this

release latch, pull the two halves of the thermostat apart near the bottom

edge.

4. Hold the base against the wall. Route the wires through the larger hole

adjacent to the terminal block. Position the base for best appearance (to

hide any marks from an old thermostat). Attach the base to the wall

with the two screws provided.

CONNECTING THE WIRES:

5. Clean bare wire ends must be inserted between the black

clamp plate and the brass terminal as shown here.

6. Securely tighten all electrical terminal screws

(even unused ones).

** Complete heating or cooling system wiring can be found in the WIRE

IDENTIFICATION AND WIRING SCHEMATICS section of this instruction

sheet. The schematics show system components for brand new instal-

lations or for un-referenced wires.

If batteries are presently installed, remove them from the thermostat before

proceeding with changing any of the options listed below.

A table similar to this one shown below is printed on the thermostat's

circuit board. There may be minor differences present in some of the

wording of your specific model, but the function of each option will be the

same.

JUMPER SETTINGS:

There are four (4) headers (or jumpers) located inside the thermostat at the

rear of the circuit board. These settings can be changed from their default

values by removing its corresponding black jumper cap and reinstalling the

cap so that it is positioned on the adjacent pair of metal pins. A change to

ANY of the option jumper settings will not be recognized unless the

thermostat has been without battery power for at least 2 minutes, and then

power is restored again. Each of these jumpers changes a different setup

option. The choices for these options are listed in a table printed on the

circuit board, and are also printed adjacent to each individual setting

jumper.

JP1 - FURNACE / HEAT PUMP SYSTEM TYPE:

This setting tells the thermostat about the type of

heating and cooling equipment that it is controlling, so

that the system is operated properly. There are two

operating modes based on your system type, “Furnace

(FURN)” or “Heat Pump (HP)”. If you have a Furnace,

ensure this is set to “Fn”. If you have a Heat Pump,

ensure this is set to “HP”.

JP2 - FAHRENHEIT OR CELSIUS DISPLAY FORMAT:

This setting controls whether the temperature is shown

in degrees °F or °C on the LCD display screen.

JP3 - GAS / ELECTRIC FAN OPERATION:

This setting defines the fan operation while in Heat

mode, and when the fan is in Auto.

GAS: Use this setting if you have a Gas or Oil heating

system. In the GAS setting, the heating system itself

controls the operation of the blower fan (if equipped).

ELECTRIC: Use this setting if you have a Heat Pump

or Electric heating system. In the ELEC setting, the

heating system requires the thermostat to control the

operation of the blower fan.

JP4 - [B] OR [O] TERMINAL USAGE OPTION:

This setting determines how the thermostat will use the

shared B/O terminal connection on the back plate. Choose

the UP (B) position to have the B/O terminal powered

while in heat mode, and un-powered while in cool and off

modes. Choose the DOWN (O) position to have the B/O

terminal powered while in cool mode, and un-powered

while in heat and off modes.

Once all optional jumper settings have been performed as described in the

previous section, please ensure that the thermostat has been without

battery power for at least 2 minutes. Now install new batteries into the

thermostat. When installing batteries, use two new Energizer®or

DURACELL®“AA” size alkaline batteries only. Ensure that the batteries are

installed in the proper direction as per the markings shown in the battery

tray.

Install your new thermostat onto its base. To do this, start with the bottom

tilted out towards you at first, and line up the two holes in the top of the

thermostat with the two hooks on the top of the back plate. Slowly pivot

the bottom of the thermostat towards the back plate and push firmly on the

bottom half of the thermostat until it is securely latched to the back plate.

If the two thermostat halves do not latch easily, remove and try again. Do

not attempt to force them together.

Turn the electrical power back ON to both your heating and/or air

conditioning systems. Verify that both systems (and the blower fan if

used) are operating properly. When set to a high temperature, the heating

system should provide warm air after a short time in Heat Mode. Likewise,

a cooling system should provide cool air after a short time when set to a

low temperature in Cool Mode. Usually, sound from the furnace and/or air

conditioning units can be heard while either is running. If your system

uses a blower fan, the rush of moving air should be heard within a short

time after either has been started. Your installation is now complete.

SYSTEM MODE SWITCH:

The MODE switch has three positions: HEAT, OFF, and COOL. In the winter,

set the mode switch to HEAT to control your heating system; in the

summer, set the switch to COOL to control your air conditioning. In the

spring and fall, or when the windows are open, you can set the switch OFF.

FAN MODE SWITCH:

The FAN switch has two positions: AUTO and ON.

• In the AUTO position, the operation of the blower fan is determined only

by the on/off cycling of the heating and cooling systems.

• When the FAN switch is in the ON position, the system's blower fan will

be commanded ON, and remain ON while the FAN switch is in the ON

position (this also includes when the System Mode Switch is in the OFF

position).

PUSH BUTTONS:

There are two push buttons to the right of the unit's display screen. These

are used to adjust the set point temperature.

TEMPERATURE ADJUSTMENT:

While in HEAT or COOL mode, a single press on either the UP or DOWN

button causes the word “SET” to appear on the screen. Once “SET” is

present, the set temperature value starts flashing and the set point

temperature can be altered by pressing either the UP or DOWN button once

per degree of change, or by holding either button for at least two seconds

to automatically increment the set point quickly in the associated direction.

Based upon the relationship of the set temperature to the displayed

ambient room temperature, the thermostat will engage either the W1

terminal in heat mode or the Y1 terminal in cool mode, if a temperature

demand is present.

(For the PSD022Ba model only):

If there is a large thermal demand present which is greater than the first

stage of heating (W1) or cooling (Y1) can accommodate for, then a second

stage of heating (W2) or cooling (Y2) will be activated. When the second

stage of either heating or cooling becomes active, the word “AUX” will be

shown on the display screen. There is approximately a 4 minute delay that

is enforced between the activation of the first stage and the second stage

of heating or cooling.

DISPLAY ILLUMINATION:

Pressing either set temperature button will illuminate the display for easier

viewing in dim light conditions. The light will remain on for approximately

12 seconds. While the light is illuminated, pressing any of the three push

buttons will continue the lighting and remain on for approximately 12 more

seconds.

MINIMUM RUN/OFF TIME:

This is determined by the thermostat, and controls the minimum length of

time that the thermostat must remain with Heat or Cool either On or Off,

before it will automatically switch to the alternate On or Off state. This

feature prevents rapid or short cycling, and provides compressor

protection for cooling equipment. The time amount for this delay is fixed at

5 minutes between on or off load changes.

TEMPERATURE LIMIT STOPS:

There are two independent set temperature stops: a Maximum Heat Set

Temperature, and a Minimum Cool Set Temperature. Each of these

temperature stops is user adjustable in one-degree increments. The heat

limit stop prevents the set temperature from being adjusted higher than the

heat limit setting. The cool limit stop prevents the set temperature from

being adjusted lower than the cool limit setting.

To set the heat and cool set temperature limit stops, always start with the

system mode switch in the OFF position. Press and hold the UP key while

sliding the mode switch from either OFF to HEAT (to adjust the maximum

heat set temperature), or from OFF to COOL (to adjust the minimum cool

set temperature). “Ht Lim” or “Cl Lim” will be displayed on the LCD screen

while you are setting the heat or cool limits respectively. While in the

adjustment mode for each of the temperature stops, use the UP and DOWN

buttons to adjust the limit value, just as you would for adjusting the set

temperature under normal operation. NOTE: If no buttons are pressed for

4 seconds, the thermostat will accept the limit value that was on the

screen, and return to normal operating mode, for the current mode switch

position. Once, complete, you should return to the adjustment mode again

for both heat and cool to confirm your desired settings for both

temperature modes.

The batteries in the thermostat should be replaced AT LEAST once per year,

or sooner if the “LO BAT” battery symbol appears in the lower right portion

of the display screen.

To replace the batteries in the thermostat, remove the thermostat’s body

from the wiring base plate attached to the wall by pressing the thumb latch

at the bottom center of the unit and swinging the front body out towards

you, up and away from the base. Remove the used batteries from the

battery tray and discard appropriately.

Install two new Energizer®or DURACELL®, “AA” size Alkaline batteries into

the battery tray. Observe the polarity markings shown in the battery

compartment to ensure proper installation. When finished, hang the top of

the unit by the tabs at the top corners of the base, and then snap the

bottom of the unit into place. Do not use unnecessary force. If the body

does not snap into place easily, remove the body, re-hang it from the tabs

at the top and try again.

If you have any problems installing or using this thermostat, please

carefully and thoroughly review the instruction manual. If you require

assistance, please contact our Technical Assistance Department at

856-234-8803 during regular business hours between 8:00AM and 4:30PM

Eastern Standard Time, Monday through Friday. You can also receive

technical assistance online anytime day or night at

http://www.luxproproducts.com. Our web site offers you answers to the

most common technical questions, and also permits you to email your

questions to our technical support staff at your convenience.

Limited Warranty: If this unit fails because of defects in materials or

workmanship within three years of the date of original purchase, LUX will,

at its option, repair or replace it. This warranty does not cover damage by

accident, misuse, or failure to follow installation instructions. Implied

warranties are limited in duration to three years from the date of original

purchase. Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you. Please return

malfunctioning or defective units to the location from which the purchase

was made, along with proof of purchase. Please refer to “Technical

ASSISTANCE” before returning thermostat. Purchaser assumes all risks

and liability for incidental and consequential damage resulting from instal-

lation and use of this unit. Some states do not allow the exclusion of

incidental or consequential damages, so the above exclusion may not apply

to you. This warranty gives you specific legal rights and you may also

have other rights which vary from state to state. Applicable in the U.S.A.

and Canada only.

Complete, Easy To Read

INSTALLATION AND OPERATING INSTRUCTIONS

PSD011Ba and PSD022Ba

IMPORTANT!

Please read all instructions carefully before beginning installation

and save for future reference. Before removing any wiring from

your existing thermostat, the wires must be labeled with their

terminal designations. Ignore the color of the wires since they

may not comply with any standard.

LUX PRODUCTS CORPORATION

Mt. Laurel, New Jersey 08054, USA

BATTERY POWERED, NON-PROGRAMMABLE

DIGITAL HEAT & COOL THERMOSTATS

WARNING: Use Energizer®or DURACELL®Alkaline Batteries Only.

Energizer®is a registered trademark of Eveready Battery Company, Inc.

DURACELL®is a registered trademark of The Gillette Company, Inc.

52066

COMPATIBILITY

WIRING INFORMATION

FEATURES

HEAT

OFF

COOL

FAN

AUTO

LUXPRO

• Digital, Non-Programmable

• Gas / Electric Blower Fan Option

• Battery Powered Only

• Set Temperature Range 45°F to 90°F

• Clean, Attractive Design

• Large, Easy To Read Display with

LED Backlight

• Easy To Install

• F / C Selectable Temperature Display

• Fixed 5 Minute Minimum Run /

Off Time For Compressor Protection

• User Adjustable Set Temperature

Limit Stops

INSTALLATION

SETUP OPTIONS

FRONT PANEL ITEMS

COMPLETING THE INSTALLATION

OPERATING INSTRUCTIONS

TECHNICAL ASSISTANCE

BATTERIES AND MAINTENANCE

WARRANTY

CAUTION:

This thermostat is protected against normal static electric discharges.

However, in extremely dry weather you should touch a grounded metal

object before touching the thermostat to minimize the risk of causing

damage to the unit.

CAUTION:

Be careful not to drop the body or disturb any

of the electronic parts.

NOTE: If you are mounting the base to a soft material like

plasterboard, or if you are using the old mounting holes, the

screws may not hold. Drill a 3/16-in (4.8mm) hole at each screw

location, and insert the plastic anchors provided. Then mount the

base as described below.

NOTE: The FAN switch only works if your system provides a wire

for the thermostat’s “G” terminal.

NOTE: Before use, remove the plastic film (if present) that is

protecting the LCD display screen.

NOTE: When the system mode switch is in the OFF position, it is

normal for the system's blower fan (“G” terminal if used) to still

become activated depending upon the position of the FAN mode

switch (see below).

CAUTION:

Turn off electricity to the appliance before

installing or servicing the thermostat or any part

of the system. Do not turn the electricity back on until

the work is completed.

• Your thermostat is a precision instrument. Please handle it with care.

• Do not short (jumper) across the electric terminals on either the furnace or

air conditioner to test the system. This may damage the thermostat and

void your warranty.

• All wiring must conform to all applicable local codes and ordinances.

• This thermostat should be limited to a maximum of 1.5 amps; higher

current may cause damage to the thermostat.

FURN

ELECT

GAS

JP1 (SYS)

JP2 (SCALE)

JP3 (FAN)

JP4 (B / O)

UP DOWN

Fan

Slide

Switch

Large Easy to

Read Backlit

Display

Quick & Easy

Temperature

Change

Buttons

Mode

Slide

Switch

NOTE: If you have an Electric Heat system and the blower does

not operate after installation, locate the “Gas/Electric” option

jumper and ensure that it is in the “Electric” position.

JP1

FURN

JP2

JP3

GAS

ELECT

JP4

(PSD011Ba, PSD022Ba) ENGLISH - WIRE IDENTIFICATION AND WIRING SCHEMATICS

(PSD011Ba, PSD022Ba) ESPAÑOL – IDENTIFICACION DE CABLES Y DIAGRAMAS DE CABLEADO

(PSD011Ba, PSD022Ba) FRANÇAIS – IDENTIFICATION DES FILS ET SCHÉMAS DE CÂBLAGE

RH R5

RRC V 5

G F

Y1 C* 6

V 5

G F

Y1 YC*

RRCRH 5

G F

Y1 YC*

RRHRC 5

YC* 6

HEATING ONLY SYSTEMS COOLING ONLY SYSTEMS

WITH ONE TRANSFORMER WITH TWO TRANSFORMERS

HEATING / COOLING SYSTEMS HEATING / COOLING SYSTEMS

B/O

GOPTIONAL

JUMPER

INSTALLED

TYPICAL SINGLE STAGE HEAT PUMP WIRING

B/O

JUMPER

INSTALLED

B/O

JUMPER

INSTALLED

B/O

PROVIDED

JUMPER

REMOVED

B/O

OPTIONAL

JUMPER

INSTALLED

“CUSTOMER SUPPLIED”

JUMPER

ADDED

OPTIONAL

022

*022

022

*022

022

TYPICAL 24 VOLT

HEATING ONLY SYSTEMS

RC RHB/O Y1 Y2 W2 W1 G

Jumper INSTALLED

System Common

STAGE-2 STAGE-1

HEATER

BLOWER

FAN

SYSTEM

XFMR

022

TYPICAL 24 VOLT, HEATING & COOLING SYSTEMS

WITH TWO TRANSFORMERS

RC RHB/O Y1 Y2 W2 W1 G

STAGE-1 STAGE-2

A/C COMPRESSOR

STAGE-2 STAGE-1

HEATER

BLOWER

FAN

COOL

XFMR HEAT

XFMR

Provided Jumper REMOVED

Common #1

Common #2

Chassis Ground

022

*022

TYPICAL 24 VOLT

COOLING ONLY SYSTEMS

RC RHB/O Y1 Y2 W2 W1 G

STAGE-1 STAGE-2

A/C COMPRESSOR

BLOWER

FAN

SYSTEM

XFMR

Jumper INSTALLED

System Common

022

TYPICAL 24 VOLT, SINGLE-STAGE

HEAT PUMP SYSTEMS

RC RHB/O Y1 Y2 W2 W1 G

SINGLE STAGE

HEAT PUMP

COMPRESSOR

REVERSING

VALVE

BLOWER

FAN

SYSTEM

XFMR

Jumper INSTALLED “Customer Supplied”

Jumper ADDED

System Common

022

TYPICAL 24 VOLT, HEATING & COOLING SYSTEMS

WITH ONE TRANSFORMER

RC RHB/O Y1 Y2 W2 W1 G

STAGE-1 STAGE-2

A/C COMPRESSOR

STAGE-2 STAGE-1

HEATER

BLOWER

FAN

SYSTEM

XFMR

Jumper INSTALLED

System Common

022

*022

022

WIRING DIAGRAM NOTES:

1. The BOLD lines are what you should be connecting to the terminals on this new

thermostat.

2. The DASHED lines are optional depending upon your system type.

3. In many cases, the thin lines shown as “SYSTEM COMMON” will not be visible at

the thermostat location, they are located with your heating and cooling equipment.

4. For Heat Pumps, use the “B” or “O” wire, NOT BOTH. Typically neither are used

in a conventional system.

5. If “Y” and “C” wires are both present, then “C” is a common wire.

6. If you have a “B” wire in your system which is used as a common wire,

connecting it to the “B/O” terminal on this thermostat may damage your system

and/or the thermostat.

RH R 5

RRC V 5

G F

Y1 C* 6

V 5

G F

Y1 YC*

R RCRH 5

G F

Y1 YC*

R RHRC 5

O B

YC* 6

SYSTÈMES DE

CHAUFFAGE SEULEMENT

SYSTÈMES DE

REFROIDISSEMENT SEULEMENT

AVEC UN SEUL TRANSFORMATEUR AVEC DEUX TRANSFORMATEURS

SYSTÈME DE CHAUFFAGE /

REFROIDISSEMENT SYSTÈME DE CHAUFFAGE /

REFROIDISSEMENT

B/O

GOPTIONNEL

CAVALIER

INSTALLÉ

FILS DE POMPE À CHALEUR À UN ÉTAGE TYPIQUE

B/O

CAVALIER

INSTALLÉ

B/O

CAVALIER

INSTALLÉ

B/O

CAVALIER

FOURNI

RETIRÉ

B/O

OPTIONNEL

CAVALIER

INSTALLÉ

CAVALIER AJOUTÉ

« FOURNI PAR LE CLIENT »

OPTIONNEL

022

*022

022

*022

022

SYSTÈMES DE CHAUFFAGE

TYPIQUE DE 24 VOLTS SEULEMENT

RC RHB/O Y1 Y2 W2 W1 G

Cavalier INSTALLÉ

Système commun

ÉTAGE-2 ÉTAGE-1

RADIATEUR

VENTILATEUR

SOUFFLANT

SYSTÈME

XFMR

022

SYSTÈMES DE CHAUFFAGE ET DE REFROIDISSEMENT

TYPIQUES DE 24 VOLTS AVEC DEUX TRANSFORMATEURS

RC RHB/O Y1 Y2 W2 W1 G

Cavalier fourni RETIRÉ

Châssis mis à la terre

Commun n° 1

Commun n° 2

REFROIDISSEMENT

XFMR

CHAUFFAGE

XFMR

ÉTAGE-1 ÉTAGE-2

COMPRESSEUR

DE CLIMATISATION

VENTILATEUR

SOUFFLANT

ÉTAGE-2 ÉTAGE-1

RADIATEUR

022

*022

SYSTÈMES DE REFROIDISSEMENT

TYPIQUE DE 24 VOLTS SEULEMENT

RC RHB/O Y1 Y2 W2 W1 G

ÉTAGE-1 ÉTAGE-2

COMPRESSEUR

DE CLIMATISATION

Cavalier INSTALLÉ

Système commun

SYSTÈME

XFMR

VENTILATEUR

SOUFFLANT

022

SYSTÈMES DE POMPE À CHALEUR

TYPIQUES À UN ÉTAGE, 24 VOLTS

RC RHB/O Y1 Y2 W2 W1 G

Cavalier INSTALLÉ

Système commun

COMPRESSEUR

DE POMPE À CHALEUR

À UN ÉTAGE

ROBINET

INVERSEUR

VENTILATEUR

SOUFFLANT

SYSTÈME

XFMR

022

SYSTÈMES DE CHAUFFAGE ET DE REFROIDISSEMENT

TYPIQUES DE 24 VOLTS AVEC UN TRANSFORMATEUR

RC RHB/O Y1 Y2 W2 W1 G

Système commun

Cavalier INSTALLÉ

ÉTAGE-1 ÉTAGE-2

COMPRESSEUR

DE CLIMATISATION

SYSTÈME

XFMR

VENTILATEUR

SOUFFLANT

ÉTAGE-2 ÉTAGE-1

RADIATEUR

022

*022

REMARQUES AU SUJET DES SCHÉMAS DE BRANCHEMENT :

1. Les lignes en GRAS représentent les fils que vous devriez connecter aux bornes de

ce nouveau thermostat.

2. Les traits TIRÉS sont optionnels d’après le type de votre système.

3. Dans de nombreux cas, les lignes minces marquées « SYSTÈME COMMUN » ne

seront pas visibles où le thermostat se trouve, car elles se trouvent avec les

appareils de chauffage et de climatisation.

4. Pour les pompes à chaleur, utilisez le fil « B » ou le fil « O », MAIS PAS LES DEUX.

Ceux-ci ne sont habituellement pas utilisés pour les systèmes traditionnels.

5. Si « Y » et « C » sont tous les deux présents, alors « C » est un fil commun.

6. Si un fil « B » de votre système est un fil commun, le connecter à la borne

« B/O » du thermostat pourrait endommager votre système et/ou le thermostat.

RH R5

RRC V 5

G F

Y1 C* 6

V 5

G F

Y1 YC*

RRCRH 5

G F

Y1 YC*

RRHRC 5

YC* 6

SISTEMAS EXCLUSIVOS

DE CALEFACCIÓN

SISTEMAS EXCLUSIVOS

DE ENFRIAMIENTO

CON UN TRANSFORMADOR CON DOS TRANSFORMADORES

SISTEMAS DE CALEFACCIÓN/ENFRIAMIENTO SISTEMAS DE CALEFACCIÓN/ENFRIAMIENTO

B/O

GOPCIONAL

PUENTE

INSTALADO

CABLES DE UNA BOMBA DE CALOR DE UNA SOLA FASE TÍPICA

B/O

PUENTE

INSTALADO

B/O

PUENTE

INSTALADO

B/O

PUENTE

PROPORCIONADO

RETIRADO

B/O

OPCIONAL

PUENTE

INSTALADO

PUENTE

"PROVISTO POR EL CLIENTE"

INCLUIDO

OPCIONAL

022

SISTEMAS TÍPICOS EXCLUSIVOS

DE CALEFACCIÓN DE 24 VOLTIOS

RC RHB/O Y1 Y2 W2 W1 G

Puente INSTALADO

Sistema Común

DOS FASES UNA FASE

CALENTADOR

VENTILADOR

SISTEMA

XFMR

022

SISTEMAS TÍPICOS DE CALEFACCIÓN Y ENFRIAMIENTO

DE 24 VOLTIOS CON DOS TRANSFORMADORES

RC RHB/O Y1 Y2 W2 W1 G

Puente Proporcionado RETIRADO

Tierra del chasis

Común #1

Común #2

ENFRIAMIENTO

XFMR

CALEFACCIÓN

XFMR

UNA FASE DOS FASES

COMPRESOR DE

AIRE ACONDICIONADO

DOS FASES UNA FASE

CALENTADOR

VENTILADOR

022

*022

SISTEMAS TÍPICOS EXCLUSIVOS

DE ENFRIAMIENTO DE 24 VOLTIOS

RC RHB/O Y1 Y2 W2 W1 G

UNA FASE DOS FASES

COMPRESOR DE

AIRE ACONDICIONADO

VENTILADOR

SISTEMA

XFMR

Puente INSTALADO

Sistema Común

022

SISTEMAS TÍPICOS DE BOMBAS DE CALOR

DE UNA SOLA FASE DE 24 VOLTIOS

RC RHB/O Y1 Y2 W2 W1 G

COMPRESOR DE

BOMBA DE CALOR

DE UNA SOLA FASE

VÁLVULA

DE INVERSIÓN

Puente INSTALADO

Sistema Común

VENTILADOR

SISTEMA

XFMR

022

SISTEMAS TÍPICOS DE CALEFACCIÓN Y ENFRIAMIENTO

DE 24 VOLTIOS CON UN TRANSFORMADOR

RC RHB/O Y1 Y2 W2 W1 G

Puente INSTALADO

Sistema Común

UNA FASE DOS FASES

COMPRESOR DE

AIRE ACONDICIONADO

DOS FASES UNA FASE

CALENTADOR

VENTILADOR

SISTEMA

XFMR

022

*022

COMENTARIOS SOBRE LOS DIAGRAMAS DE CABLEADO:

1. Las líneas RESALTADAS son las que debe conectar a los terminales de este

nuevo termostato.

2. Las líneas ENTRECORTADAS son opcionales de acuerdo con su tipo de sistema.

3. En muchos casos, las líneas delgadas, que se indican como “SISTEMA COMUN”,

no se pueden ver en el termostato porque se encuentran en su equipo de

calefacción y refrigeración.

4. Para las bombas de calor, use el alambre “B” u “O”, NO AMBOS. Generalmente

no se utiliza ninguno en un sistema convencional.

5. Si hay un alambre “Y” y un alambre “C”, el común será el alambre “C”.

6. Si un alambre “B” en su sistema se utiliza como alambre común, entonces

conectarlo al terminal "B/O" del terminal del termostato puede causar daños a su

sistema y/o al termostato.

022*

(PSD022Ba)

SEULEMENT

022*

(PSD022Ba)

SEULEMENT

022*

(PSD022Ba)

SEULEMENT

022*

(PSD022Ba)

SEULEMENT

022*

(PSD022Ba)

SEULEMENT

022*

(PSD022Ba)

SEULEMENT

022*

(PSD022Ba)

ONLY

022*

(PSD022Ba)

ONLY

022*

SÓLO

(PSD022Ba)

022*

SÓLO

(PSD022Ba)

022*

SÓLO

(PSD022Ba)

022*

SÓLO

(PSD022Ba)

022*

SÓLO

(PSD022Ba)

022*

SÓLO

(PSD022Ba)

52066

022*

(PSD022Ba)

ONLY

022*

(PSD022Ba)

ONLY

022*

(PSD022Ba)

ONLY

022*

(PSD022Ba)

ONLY

Luxpro PSD011Ba Manuel utilisateur

Marque: Luxpro

Modèle: PSD011Ba

Catégorie: Thermostats

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Luxpro PSD011Ba User manual

Luxpro PSD011Ba Manuel utilisateur

Luxpro PSD011Ba Manuel utilisateur

dans d''autres langues

Autres documents