Ryobi CS26 Manuel utilisateur

Marque: Ryobi

Modèle: CS26

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

CS26

RY28021

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

26CC STRING TRIMMERS

TAILLE-BORDURES À LIGNE DE 26 CC

RECORTADORAS DE HILO 26 CC

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

Ce taille-bordures a été conçu et fabriqué conformément à

nos strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, cet outil vous donnera des

années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su recortadora ha sido diseñado y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de uso

y seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and opera-

tor safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

SS26

RY28041

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées

dans le manuel d’utilisation.

Consulte esta sección desplegable

para ver todas las figuras a las que se

hace referencia en el manual del operador.

iii

CS26

DEFG

Fig. 1

A - Reel-Easy™ tap advance string head

(avance de la ligne de coupe à tapant

Reel-Easy™, sistema de avance de hilo por

golpe Reel-Easy™)

B - Drive shaft housing (tube de l’arbre moteur,

alojamiento del eje de impulsión)

C - Coupler (coupleur, acoplador)

D - Front handle (poignée avant, mango

delantero)

E - Strap hanger (dispositif d’accrochage,

colgador para la correa)

Fig. 2

A - Button (bouton, botón)

B - Guide recess (logement guide, hueco guía)

C - Coupler (coupleur, acoplador)

D - Power head shaft (arbre du bloc moteur, eje

del cabezal motor)

E - Knob (bouton, perilla)

F - Positioning hole (trou de positionnement,

orificio de posicionamiento)

G - Trimmer attachment (accessoire taille-

bordures, aditamento para recortar)

BCD

Fig.3

A - Button (bouton, botón)

B - Secondary hole (trou secondaire, orificio

secundario)

C - Hole (trou, orificio)

D - Hanger cap (capuchon de suspension, tapa

de suspensión)

DFig. 4

A - Bolt (boulon, perno)

B - Front handle (poignée avant, mango

delantero)

C - Washer (rondelle, arandela)

D - Wing nut (écrou papillon, tuerca de

mariposa)

SS26

F - Stop switch (l’interrupteur d’arrêt, interruptor

de parada)

G - Trigger lock-out (verrouillage de gâchette,

seguro del gatillo)

H - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

I - Primer bulb (poire d’amorçage, bomba de

cebado)

J - Fuel cap (bouchon de carburant, tapa del

tanque)

K - Rear handle (poignée arrière, mango trasero)

L - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

- Knob (bouton, perilla)

N - Curved shaft grass deflector (déflecteur

d’herbe d’arbre courbe, deflector de pasto del

eje curvo)

O - Straight shaft grass deflector (déflecteur

d’herbe d’arbre droit, deflector de pasto para

eje recto)

P - Muffler (silencieux, silenciador)

Fig. 6

A - Straight shaft grass deflector (déflecteur

d’herbe d’arbre droit, deflector de pasto para

eje recto)

B - Slot (fente, ranura)

C - Tab (languette, orejeta)

D - Wing screw (vis à oreilles, tornillo de

mariposa)

A - Stop switch (l’interrupteur d’arrêt, interruptor

de parada)

B - Trigger lock-out (verrouillage de gâchette,

seguro del gatillo)

C - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

D - Starter handle and rope (poignée du lanceur

et corde, mango del arrancador y cuerda)

Fig. 7

A - Stop switch (l’interrupteur d’arrêt, interruptor

de parada)

B - Trigger lock-out (verrouillage de gâchette,

seguro del gatillo)

C - Primer bulb (poire d’amorçage, bomba de

cebado)

D - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

Fig. 8

Fig. 9

A - Full choke (volet de départ ouvert, anegación

máxima)

B - Choke lever (levier de volet de départ,

palanca del anegador)

C - Run position (position de marche, posición

de marcha)

Fig. 5

A - Bolt (boulon, perno)

B - Bracket (support, placa)

C - Washer (rondelle, arandela)

D - Wing nut (écrou à oreilles, tuerca de

mariposa)

E - Curved shaft grass deflector (déflecteur

d’herbe, deflector de pasto)

PROPER OPERATING POSITION

BONNE POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO

DE LA HERRAMIENTA

Fig. 10

A - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

B - Curved shaft trimmer (taille-bordures à

arbre courbe, recortadora de eje curvo)

C - Direction of rotation (sens de rotation,

sentido de rotación)

D - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

Fig. 11 B

Fig. 15

A - Pull strings (tirer vers l’extérieur, tira del

hilo)

B - Rotate the spool clockwise (tourner le

bobine dans le sens horaire, gire a la derecha

el carrete)

Fig. 20

A - Latch (loquet, pestillo)

B - Pull cover to open (tirer sur le couvercle

pour l’ouvrir, tire de la tapa para abrirla)

C - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

Fig. 21

A - Latch (loquet, pestillo)

B - Filter screen (filtre écran, filtro pantalla)

C - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

Fig. 14

Fig. 17

A - Spool retainer (retenue de bobine, retén del

carrete)

Fig. 16

A - Eyelet (oeillet, ojillo)

B - Arrow on spool (flèche sur la bobine, flecha

en el carrete)

A - Spool retainer (retenue de bobine, retén del

carrete)

B - Spool (bobine, carrete)

A - Pull strings (tirer vers l’extérieur, tira del

hilo)

Fig. 18

A - Straight shaft trimmer (taille-bordures à

arbre droit, recortadora de eje recto)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Best cutting area (zone d’efficacité maximum,

mejor área de corte)

D - Direction of rotation (sens de rotation,

sentido de rotación)

Fig. 12

A - Straight shaft trimmer cut-off blade (lame

de sectionnement de ligne du taille-bordures

à arbre droit, cuchilla de corte de hilo de la

recortadora de eje recto)

B - Curved shaft trimmer cut-off blade (lame de

sectionnement de ligne du taille-bordures à

arbre courbe, cuchilla de corte de hilo de la

recortadora de eje recto)

Fig. 13

Fig. 19

A - Idle speed screw (vis de ralenti, tornillo de

ajuste de la velocidad en vacío)

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 General Safety Rules .....................................................................................................................................................3-4

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules ........................................................................................................................................................ 4

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ............................................................................................................................................................................ 5

Symboles / Símbolos

 Features ............................................................................................................................................................................6

Caractéristiques / Características

 Assembly .......................................................................................................................................................................6-8

Assemblage / Armado

 Operation ..................................................................................................................................................................... 8-10

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................10-12

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 13

Dépannage / Solución de problemas

 Warranty ....................................................................................................................................................................14-15

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

3 — English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

 Never start or run the engine in a closed or poorly venti-

lated area; breathing exhaust fumes can kill.

 Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or loose string

which can be thrown or become entangled in the cutting

line or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

 Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

 Heavy protective clothing may increase operator fatigue,

which could lead to heat stroke. During weather that is

hot and humid, heavy work should be scheduled for early

morning or late afternoon hours when temperatures are

cooler.

 Product users on United States Forest Service land, and in

some states, must comply with fire prevention regulations.

This product is equipped with a spark arrestor; however,

other user requirements may apply. Check with your

federal, state, or local authorities.

 Never operate this unit on the operator’s left side.

 Secure long hair above shoulder level to prevent

entanglement in moving parts.

 Keep all bystanders, children, and pets at least

50 ft. away. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the engine

and cutting attachment. In the case of bladed units, there

is the added risk of injury to bystanders from being struck

with the moving blade in the event of a blade thrust or

other unexpected reaction of the saw.

 Do not operate this unit when you are tired, ill, or under

the influence of alcohol, drugs, or medication.

 Do not operate in poor lighting.

 Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure

to hot surfaces.

 Keep all parts of your body away from any moving part.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

 Do not touch area around the muffler or cylinder of the

unit, these parts get hot from operation. Contact with hot

surfaces could result in possible serious personal injury.

 Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 The cutting attachment should never rotate at idle during

normal use. The cutting attachment may rotate at idle

during carburetor adjustments.

 It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness, and blanching of the fingers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking, and work practices

are all thought to contribute to the development of these

symptoms. It is presently unknown what, if any, vibrations

or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to

possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operating

the unit wear gloves to keep hands and wrists warm.

It is reported that cold weather is a major factor con-

tributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to increase

blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the tool well maintained, fasteners tightened,

and worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician about

these symptoms.

 Mix and store fuel in a container approved for gasoline.

 Mix fuel outdoors where there are no sparks or flames.

Wipe up any fuel spillage. Move 30 ft. away from refueling

site before starting engine. Slowly remove the fuel cap

after stopping engine. Do not smoke when refueling.

4 — English

SPECIFIC SAFETY RULES

SPECIFIC SAFETY RULES FOR TRIMMER

USE

 Inspect before use. Replace damaged parts. Make sure

fasteners are in place and secure. Check for fuel leaks.

 Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head or blade is properly

installed and securely fastened. Failure to do so can cause

serious injury.

 Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

 Never use blades, flailing devices, wire, or rope. Use only

the manufacturer’s replacement line in the cutting head.

Do not use any other cutting attachment. To install any

other brand of cutting head to this string trimmer can

result in serious personal injury.

 Never operate unit without the grass deflector in place

and in good condition.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

 This product is intended for infrequent use by homeown-

ers and other occasional users for such general applica-

tions as trimming light and heavy vegetation, etc. It is not

intended for prolonged use. Prolonged periods of opera-

tion can cause circulatory problems in the user’s hands

due to vibration. For such use, it may be appropriate to

use a product having an anti-vibration feature.

GENERAL SAFETY RULES

 Stop the engine and allow to cool before refueling or

storing the unit.

 Allow the engine to cool; empty the fuel tank and secure

the unit from moving before transporting in a vehicle.

 Wear your protective equipment and observe all safety

instructions. For units equipped with a clutch, be sure

the cutting attachment stops turning when the engine

idles. When the unit is turned off make sure the cutting

attachment has stopped before the unit is set down.

5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and under-

stand operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet Thrown objects can ricochet and result in personal injury

or property damage.

No Blade Do not install or use any type of blade on a product dis-

playing this symbol.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use

with an octane rating of 87 [(R + M) / 2] or higher. This

product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

6 — English

FEATURES

PRODUCT SPECIFICATIONS

Weight - (without fuel)

CS26 ...................................................................................................................................................................10.3 lbs.

SS26 ...................................................................................................................................................................11.8 lbs.

Line cutting width

CS26 ........................................................................................................................................................................17 in.

SS26 ........................................................................................................................................................................18 in.

Engine displacement ....................................................................................................................................................26cc

Line diameter ...........................................................................................................................................................0.095 in.

KNOW YOUR PRODUCT

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

GRASS DEFLECTOR

The product includes a grass deflector that helps protect

you from flying debris.

REEL-EASY™ TAP ADVANCE SYSTEM

The Reel-Easy™ Tap Advance System allows easy line

advance during trimmer operation.

TOP-MOUNTED MOTOR

The top-mounted motor improves balance and is located

away from the dust and debris of the cutting area.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the items from the box. Make sure that

all items listed in the packing list are included.

WARNING:

Do not use this product if any parts on the packing list are

already assembled to your product when you unpack it.

Parts on this list are not assembled to the product by the

manufacturer and require customer installation. Use of a

product that may have been improperly assembled could

result in serious personal injury.

 Inspect the unit carefully to make sure no damage occurred

during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

CS26

Trimmer Assembly

Front Handle

Curved Shaft Grass Deflector

Bottle of 2-Cycle Lubricant

Operator’s Manual

SS26

Trimmer Assembly

Front Handle

Straight Shaft Grass Deflector

Bottle of 2-Cycle Lubricant

Operator’s Manual

7 — English

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

INSTALLING THE POWER HEAD TO THE

ATTACHMENT

See Figure 2.

WARNING:

Never install, remove, or adjust any attachment while

power head is running. Failure to stop the engine can

cause serious personal injury.

The attachment connects to the power head by means of

a coupler device.

 Loosen the knob on the coupler of the power head shaft

and remove the hanger cap from the attachment.

 Push in the button located on the trimmer attachment.

Align the button with the guide recess on the power

head coupler and slide the two shafts together. Rotate

the trimmer attachment until the button locks into the

positioning hole.

NOTE: If the button does not release completely in the

positioning hole, the shafts are not locked into place.

Slightly rotate from side to side until the button is locked

into place.

 Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating

equipment; check it periodically for tightness during use

to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE

POWER HEAD

For removing or changing the attachment:

 Loosen the knob.

 Push in the button and twist the shafts to remove and

separate ends.

ATTACHING THE STORAGE HANGER

See Figure 3.

There are two ways to hang your attachment for storage:

To use the hanger cap, push in the button and place

the hanger cap over end of trimmer attachment. Slightly

rotate the cap from side to side until the button locks into

place.

 The secondary hole in the trimmer attachment can be

used for hanging purposes as well.

ATTACHING THE FRONT HANDLE

See Figure 4.

 Remove wing nut, washer, and bolt from the front handle.

 Install the front handle onto the top side of the drive shaft

housing in the area indicated by the label.

NOTE: The open side of the handle should face the

operator.

 Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess molded

into one side of the handle.

 Reinstall the washer and wing nut.

 Tighten wing nut securely.

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp.

Avoid contact with the blade. Failure to avoid contact

can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS

DEFLECTOR - CS26

See Figure 5.

 Remove hex screw, washer, and wing nut from grass

deflector.

 Press the grass deflector onto the bottom of the curved

shaft as shown.

 Insert the hex screw through the grass deflector and the

bracket on the curved shaft.

 Place the washer on the hex screw.

 Place the wing nut on the hex screw and tighten

securely.

8 — English

TO ATTACH THE STRAIGHT SHAFT GRASS

DEFLECTOR - SS26

See Figure 6.

 Remove the wing screw from the grass deflector.

 Insert the tab on the mounting bracket in the slot on the

grass deflector.

ASSEMBLY

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Never use blades, flailing devices, wire, or rope on this

product. Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

WARNING:

Operation of this equipment may create sparks that

can start fires around dry vegetation. A spark arrestor

may be required. The operator should contact local fire

agencies for laws or regulations relating to fire prevention

requirements.

FUELING AND REFUELING THE TRIMMER

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

Recommended fuel: This engine is certified to operate on

unleaded gasoline intended for automotive use.

NOTE: We recommend you use Homelite premium 2-cycle

lubricant, PowerCare 2-cycle lubricant (6.4 oz. or 16 oz.), or

an equivalent high-quality synthetic 2-cycle lubricant in this

product. Mix at 2.6 oz. per gallon (US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)

FILLING TANK

 Clean surface around fuel cap to prevent contamination.

 Loosen fuel cap slowly. Rest the cap on a clean surface.

 Carefully pour fuel into the tank. Avoid spillage.

 Prior to replacing the fuel cap, clean and inspect the

gasket.

 Immediately replace fuel cap and hand tighten. Wipe up

any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new

engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to

a machine with a running or hot engine. Move at least

30 ft. from refueling site before starting engine. Do not

smoke! Failure to heed this warning could result in seri-

ous personal injury.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR

WARRANTY.

NOTE: Fuel system damage or performance problems re-

sulting from the use of an oxygenated fuel containing more

than the percentages of oxygenates stated below are not

covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E85 is not.

STARTING AND STOPPING

See Figures 7 - 9.

Trimmer should be on a flat, bare surface for starting.

To start a cold engine:

Slowly press the primer bulb 10 times.

 Align the screw hole in the mounting bracket with the

screw hole in the grass deflector.

 Insert the wing screw through the mounting bracket and

into the grass deflector.

 Tighten the screw securely.

OPERATION

9 — English

OPERATION

NOTE: After the 7th press, fuel should be visible in the

primer bulb. If it is not, continue to press the primer until

you see fuel in the bulb.

Set the choke lever to the FULL CHOKE position.

Squeeze the throttle trigger fully and pull starter grip and

rope sharply until engine attempts to run. Do not pull the

starter grip and rope more than four (4) times.

NOTE: Keep throttle trigger squeezed fully.

Set the choke lever to the HALF CHOKE position.

Pull the starter grip and rope until the engine runs. Do not

pull the starter grip and rope more than six (6) times.

NOTE: If the engine does not start, return to the FULL

CHOKE position and repeat the steps that follow.

Allow the engine to run for 10 seconds, then set the choke

lever to the RUN position.

To restart a warm engine:

Slowly press the primer bulb 10 times.

Set the choke lever to the RUN position.

Squeeze the throttle trigger fully and pull the starter grip

and rope until the engine runs.

To stop the engine:

 To stop the engine, depress the STOP switch to the stop

position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

OPERATING THE TRIMMER

See Figure 10.

WARNING:

Engine housing may become hot during trimmer opera-

tion. Do not rest or place your arm, hand, or any body

part against the engine housing during trimmer operation.

Only hold the trimmer as shown in Figure 10 with all body

parts clear of engine housing. Extended contact with the

engine housing can result in burns or other injuries.

WARNING:

Always position the unit on the operator’s right side. The

use of the unit on the operator’s left side will expose the

user to hot surfaces and can result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with

the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Trimmer should be held at a

comfortable position with the rear handle about hip height.

Always operate trimmer in RUN position. Cut tall grass

from the top down. This will prevent grass from wrapping

around the shaft housing and string head which could cause

damage from overheating. If grass becomes wrapped around

the string head, STOP THE ENGINE, disconnect the spark

plug wire, and remove the grass. Prolonged cutting at partial

throttle will result in lubricant dripping from the muffler.

WARNING:

Always hold the string trimmer away from the body keep-

ing clearance between the body and the product. Any

contact with the housing or string trimmer cutting head

can result in burns and/or other serious personal injury.

CUTTING TIPS

See Figures 10 - 12.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 10.)

 Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

 The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in illustration.

 Use the tip of line to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra line wear, even

breakage. Stone and brick walls, curbs, and wood may

wear line rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the line.

ADVANCING STRING USING THE REEL-EASY™

TAP ADVANCE SYSTEM

String advance is controlled by tapping the string head’s

spool retainer on grass while running engine at full throttle.

 Run engine at full throttle.

 Tap string head on ground to advance string. String

advances each time the head is tapped.

 Several taps may be required until string strikes the cut

off blade.

 Resume trimming.

NOTE: If the string is worn too short you may not be able to

advance the string by tapping it on the ground. If so, STOP

THE ENGINE, disconnect the spark plug wire, and manually

advance the string.

10 — English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal injury.

You can often make adjustments and repairs described here.

For other repairs, have the trimmer serviced by an authorized

service dealer.

OPERATION

ADVANCING THE STRING MANUALLY

With the engine off and the spark plug wire disconnected,

push the spool retainer down while pulling on string(s) to

manually advance the string.

GRASS DEFLECTOR LINE TRIMMING CUT-OFF

BLADE

See Figure 13.

The trimmer is equipped with a line trimming cut-off blade on

the grass deflector. For best cutting, advance line until it is

trimmed to length by the cut-off blade. Advance the line when-

ever you hear the engine running faster than normal, or when

trimming efficiency diminishes. This will maintain best perfor-

mance and keep the line long enough to advance properly.

MAINTENANCE

SPOOL REPLACEMENT

REEL-EASY™ TAP ADVANCE SYSTEM

See Figures 14 - 16.

If replacing line only, refer to Line Replacement later in this

manual.

Use only .095 in. trimmer line.

 Stop the engine and disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for 26CS.

Turn the spool retainer clockwise for 26SS.

 Remove the empty spool from the string head.

NOTE: It is not necessary to remove the string head

housing from the drive shaft.

 Insert the new spool into the string head.

NOTE: Make sure the arrows on the spool are aligned

with the eyelets in the string head housing. Push down

and hold the spool and housing together while complet-

ing the installation.

 Reinstall the spool retainer to secure.

To install the spool retainer:

Turn the spool retainer clockwise for CS26.

Turn the spool retainer counterclockwise for SS26.

 Install line as described in LINE REPLACEMENT.

LINE REPLACEMENT

See Figures 16 - 18.

 Stop the engine and disconnect the spark plug wire.

 Rotate the spool clockwise as necessary to align the arrows

on the spool with the eyelets in the string head housing.

 Cut one piece of trimmer line 10 ft. long. Insert the line

into the eyelet on the string trimmer housing. Push until

the end of the line comes out the other side of the string

head. Pull the line from the other side until equal amounts

of line appear on both sides of the spool.

11 — English

MAINTENANCE

 Rotate the spool clockwise to wind the line on the spool

until approximately 6 in. of line is showing on each side.

 Push the spool retainer down while pulling on line(s) to

manually advance the line and to check for proper as-

sembly of the string head.

CLEANING THE EXHAUST PORT, MUFFLER,

AND SPARK ARRESTOR

NOTE: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions, the

exhaust port, muffler, and/or spark arrestor screen may be-

come blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualified service technicians perform this

service.

The spark arrestor must be cleaned or replaced every 50

hours or yearly to ensure proper performance of your prod-

uct. Spark arrestors may be in different locations depending

on the model purchased. Please contact your nearest service

dealer for the location of the spark arrestor for your model.

IDLE SPEED ADJUSTMENT

See Figure 19.

WARNING:

The blade/cutting head will move when adjusting the

idle speed. Wear all protective clothing and keep all by-

standers, children, and pets at least 50 ft. away. Make

adjustments with the unit supported by hand so that the

blade/cutting head does not contact the ground or any

object. Keep all parts of your body away from the blade/

cutting head and muffler. Failure to follow these instruc-

tions could result in serious personal injury.

If the cutting attachment turns at idle, the idle speed screw

needs adjusting on the engine. Turn the idle speed screw

counterclockwise to reduce the idle RPM and stop the cut-

ting attachment movement. If the cutting attachment still

moves at idle speed, contact a service dealer for adjustment

and discontinue use until the repair is made.

WARNING:

The cutting attachment should never turn at idle. Turn

the idle speed screw counterclockwise to reduce the

idle RPM and stop the cutting attachment, or contact a

service dealer for adjustment and discontinue use until

the repair is made. Serious personal injury could result

from the cutting attachment turning at idle.

CLEANING AIR FILTER SCREEN

See Figures 20 - 21.

For proper performance and long life, keep air filter screen

clean.

 Remove the air filter cover by pushing down on the latch

with your thumb while gently pulling on the cover.

 Brush the air filter screen lightly to clean.

 Replace the air filter cover by inserting the tabs on the

bottom of the cover into the slots on the air filter base;

push the cover up until it latches securely in place.

FUEL CAP

WARNING:

Check for fuel leaks. A leaking fuel cap is a fire hazard

and must be replaced immediately. If you find any leaks,

correct the problem before using the product. Failure

to do so could result in a fire that could cause serious

personal injury.

The fuel cap contains a non-serviceable filter and a check

valve. A clogged fuel filter will cause poor engine perfor-

mance. If performance improves when the fuel cap is loos-

ened, check valve may be faulty or filter clogged. Replace

fuel cap if required.

SPARK PLUG REPLACEMENT

This engine uses a Champion RCJ-6Y, NGK BPMR7A, or

Ryobi AC00160 spark plug with .025 in. electrode gap. Use

an exact replacement and replace annually.

STORING THE PRODUCT

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.

 Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

HIGH ALTITUDE ENGINE OPERATION

Please have an authorized service center adjust this engine

if it is to be run above 2000 feet. Failure to do so may result

in poor engine performance and increased emissions. An

engine adjusted for high altitudes can not be run at 2000

feet or lower. In doing so, the engine will overheat and cause

serious engine damage. Please have an authorized service

center restore high altitude modified engines to the original

factory specification before operating below 2000 feet.

12 — English

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST

Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every

Each Use 5 Hours Every 25 Hours 25 Hours 125 Hours

or Yearly or Yearly

CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X

AIR FILTER ASSY

includes:

Filter Screen ..................................................... X

SPARK SCREEN ................................................................................................................................................X

CARBURETOR ASSY

includes:

Heat Dam ........................ X

Gaskets ........................... X

FUEL TANK ASSY

includes:

Fuel Lines ........................ X

Fuel Cap .......................... X

Fuel Filter

IGNITION ASSY

includes:

Spark Plug ........................................................................................ X

ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR THREE YEARS OR FOR THE PERIOD OF TIME PRIOR TO

THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

CALL US FIRST

For any questions about operating or maintaining your product,

call the Ryobi® Help Line!

Your product has been fully tested prior to shipment to ensure

your complete satisfaction.

MAINTENANCE

13 — English

PROBLEM POSSIBLE CAUSE SOLUTION

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

TROUBLESHOOTING

1. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

2. Push primer bulb until bulb is full of fuel. If bulb

does not fill, primary fuel delivery system is

blocked. Contact an authorized service dealer. If

primer bulb fills, engine may be flooded, proceed

to next item.

3. Set the CHOKE lever to the RUN position.

Squeeze the trigger and pull the rope repeatedly

until the engine starts and runs.

NOTE: Depending on the severity of the flooding,

this may require numerous pulls of the rope.

1. Use fresh fuel and the correct 2-cycle lubricant

mix. (50:1).

2. Clean air filter screen. Refer to Cleaning Air

Filter Screen earlier in this manual.

3. Contact an authorized servicing dealer.

4. Clean or replace spark plug. Reset spark plug

gap. Refer to Spark Plug Replacement earlier

in this manual.

1. Turn idle speed screw clockwise to increase idle

speed. See Figure 19.

1. Lubricate line with silicone spray.

2. Install more line. Refer to the applicable line

replacement section in this manual.

3. Pull lines while alternately pressing down on and

releasing spool retainer.

4. Remove line from spool and rewind. Refer to

the applicable line replacement section in this

manual.

5. Advance line at full throttle.

Engine will not start

Engine does not reach full

speed and emits excessive

smoke

Engine starts, runs, and ac-

celerates but will not idle

Line will not advance

1. No spark.

2. No fuel.

3. Engine is flooded.

1. Incorrect lubricant/fuel mixture.

2. Air filter screen is dirty.

3. Spark arrestor screen is dirty.

4. Spark plug fouled.

1. Idle speed screw on carburetor

needs adjustment.

1. Line is welded to itself.

2. Not enough line on spool.

3. Line is worn too short.

4. Line is tangled on spool.

5. Engine speed is too slow.

1. Clean threads and lubricate with grease - if no

improvement, replace the spool retainer.

1. Cut tall grass from the top down to prevent

wrapping.

2. Operate trimmer at full throttle.

Spool retainer hard to turn

Grass wraps around drive

shaft housing and string

head

1. Screw threads are dirty or

damaged.

1. Cutting tall grass at ground

level.

2. Operating trimmer at part

throttle.

14 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Techtronic Industries North America, Inc., warrants to the

original retail purchaser that this RYOBI® brand outdoor

product is free from defect in material and workmanship

and agrees to repair or replace, at Techtronic Industries

North America, Inc.’s, discretion, any defective product

free of charge within these time periods from the date of

purchase.

 Three years if the product is used for personal, family

or household use;

 30 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser only

and commences on the date of the original retail purchase.

Any part of this product found in the reasonable judgment

of Techtronic Industries North America, Inc. to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by an authorized service

center for RYOBI® brand outdoor products (Authorized

Ryobi Service Center).

The product, including any defective part, must be returned

to an authorized Ryobi service center within the warranty

period. The expense of delivering the product to the service

center for warranty work and the expense of returning it

back to the owner after repair or replacement will be paid

by the owner. Techtronic Industries North America, Inc.’s,

responsibility in respect to claims is limited to making the

required repairs or replacements and no claim of breach of

warranty shall be cause for cancellation or rescission of the

contract of sale of any RYOBI® brand outdoor product. Proof

of purchase will be required by the dealer to substantiate

any warranty claim. All warranty work must be performed

by an authorized service dealer.

This warranty is limited to thirty (30) days from the date

of original retail purchase for any RYOBI® brand outdoor

product that is used for rental or commercial purposes, or

any other income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in this operator’s manual. This

warranty does not apply to any damage to the product that

is the result of improper maintenance or to any product

that has been altered or modified. The warranty does not

extend to repairs made necessary by normal wear or by the

use of parts or accessories which are either incompatible

with the RYOBI® brand outdoor product or adversely affect

its operation, performance, or durability. In addition, this

warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bag

and Straps, Guide Bars, Saw Chains, Blades

Techtronic Industries North America, Inc., reserves the

right to change or improve the design of any RYOBI® brand

outdoor product without assuming any obligation to modify

any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED

IN THEIR ENTIRETY AFTER THE EXPIRATION OF

THE APPROPRIATE THREE-YEAR OR THIRTY-DAY

WARRANTY PERIOD. TECHTRONIC INDUSTRIES

NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO

THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS

AND TECHTRONIC INDUSTRIES NORTH AMERICA,

INC., DOES NOT ASSUME OR AUTHORIZE ANYONE

TO ASSUME FOR THEM ANY OTHER OBLIGATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC

INDUSTRIES NORTH AMERICA, INC., ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,

OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO, EXPENSE OF RETURNING THE PRODUCT TO AN

AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE

OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all RYOBI® brand outdoor products

manufactured by or for Techtronic Industries North America,

Inc., and sold in the United States and Canada.

To locate your nearest Authorized Ryobi Service Center,

dial 1-800-860-4050.

15 — English

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUMBERS

REQUIRED TO MEET THE CARB REQUIREMENTS.

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board

(CARB), and Techtronics Industries North America, Inc., are pleased to explain the

Emissions Control System Warranty on your non-road or small off-road engine. In

California, new equipment that uses small off-road engines must be designed, built,

and equipped to meet the state’s stringent anti-smog standards. In other states, new

2011 and later model year non-road engines must be designed, built, and equipped

at the time of sale to meet the U.S. EPA regulations for small non-road engines. The

non-road engine must be free from defects in materials and workmanship which cause

it to fail to conform with U.S. EPA standards for the first three years of engine use

from the date of sale to the ultimate purchaser. Techtronics Industries North America,

Inc., must warrant the emission control system on your non-road or small off-road

engine for the period of time listed above provided there has been no abuse, neglect,

or improper maintenance of your non-road or small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection

system, the ignition system, catalytic converters, fuel tanks, valves, filters, clamps,

connectors, and other associated components. Also included may be hoses, belts

and connectors, and other emission-related assemblies.

Where a warrantable condition exists, Techtronics Industries North America, Inc.,

will repair your non-road or small off-road engine at no cost to you, including diag-

nosis, parts, and labor performed at an authorized service center for RYOBI® brand

outdoor products.

MANUFACTURER’S WARRANTY COVERAGE:

This product’s emissions control system is warranted for three years. If any

emission-related part on your engine is defective, the part will be repaired or replaced

by Techtronics Industries North America, Inc., free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a) As the non-road or small off-road engine owner, you are responsible for the

performance of the required maintenance listed in your operator’s manual. Tech-

tronics Industries North America, Inc., recommends that you retain all receipts

covering maintenance on your non-road or small off-road engine, but Techtronics

Industries North America, Inc., cannot deny warranty solely for the lack of re-

ceipts or for your failure to ensure the performance of all scheduled maintenance.

(b) As the non-road or small off-road engine owner, you should be aware, however,

that Techtronics Industries North America, Inc., may deny you warranty coverage if

your non-road or small off-road engine or a part has failed due to abuse, neglect,

improper maintenance, or unapproved modifications.

authorized service dealer as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you

should contact a Techtronics Industries North America, Inc., Customer Representa-

tive at 1-800-860-4050.

DEFECT WARRANTY COVERAGE REQUIREMENTS:

(a) The warranty period begins on the date the engine or equipment is delivered to

an ultimate purchaser.

(b) General Emissions Warranty Coverage. Techtronics Industries North America,

Inc., warrants to the ultimate purchaser and each subsequent purchaser that your

non-road or small off-road engine is designed, built, and equipped at the time of sale

to conform with all applicable regulations adopted by the California Air Resources

Board or the United States Environmental Protection Agency; and that it is free from

defects in materials and workmanship which cause the engine to fail to conform

with applicable regulations for a period of three years from the date the non-road or

small off-road engine is purchased by the initial purchaser. Any replacement part or

service that is equivalent in performance and durability may be used in non-warranty

maintenance or repairs, and shall not reduce the warranty obligations of Techtronics

Industries North America, Inc.

Any warranted part that is not scheduled for replacement as required in the

Maintenance Schedule is warranted for three years. If any such part (including

any part that is scheduled only for regular inspection) fails during the period

of warranty coverage, it will be repaired or replaced at any RYOBI® Autho-

rized Service Center at no charge. Any such part repaired or replaced under

warranty will be warranted for the remaining warranty period. A statement

to the effect of “repair or replace as necessary” would not reduce the period

of warranty coverage. Any warranted part that is scheduled for replacement

as required maintenance in the Maintenance Schedule is warranted for the

period of time prior to the first scheduled replacement point for that part.

Any such part repaired or replaced under warranty is warranted for the

remainder of the period prior to the first scheduled replacement point, and

will be repaired or replaced at any RYOBI® Authorized Service Center for no

charge until that replacement point is reached.

Techtronics Industries North America, Inc., shall remedy warranty defects at any

authorized RYOBI® Authorized Service Center, including any distribution center

that may be franchised to service the subject engines. Any diagnostic work done

at a RYOBI® Authorized Service Center shall be free of charge to the owner if such

work determines that a warranted part is defective. Any manufacturer-approved or

equivalent replacement part may be used for any warranty maintenance or repairs

on emission-related parts, and must be provided free of charge to the owner if the

part is still under warranty. Techtronics Industries North America, Inc., is liable for

damages to other engine components caused by the failure of a warranted part still

under warranty.

Add-on or modified parts that are not exempted by the California Air Resource Board

may not be used. The use of any non-exempted add-on or modified parts will be

grounds for disallowing a warranty claim. Techtronics Industries North America,

Inc., will not be liable to warrant failures of warranted parts caused by the use of a

non-exempted add-on or modified part.

The Emission Parts List specifically defines the emission-related warranted

parts. Techtronics Industries North America, Inc., will provide any documents that

describe its warranty procedures or policies within five days upon request by the

California Air Resources Board.

EMISSIONS PARTS LIST

Emissions parts vary from product to product. Your emissions control system warranty

applies to any of the following components that may be included on your product:

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or fuel injection

system).

(ii) Air/fuel ratio feedback and control system.

(iii) Cold start enrichment system.

(iv) Fuel Tank.

(2) Air Induction System

(i) Controlled hot air intake system.

(ii) Intake manifold.

(iii) Air filter.

(3) Ignition System

(i) Spark plugs.

(ii) Magneto or electronic ignition system.

(iii) Spark advance/retard system.

(4) Exhaust Gas Recirculation (EGR) System

(i) EGR valve body and carburetor spacer, if applicable.

(ii) EGR rate feedback and control system.

(5) Air Injection System

(i) Air pump or pulse valve.

(ii) Valves affecting distribution of flow.

(iii) Distribution manifold.

(6) Catalyst or Thermal Reactor System

(i) Catalytic converter.

(ii) Thermal reactor.

(iii) Exhaust manifold.

(7) Particulate Controls

(i) Traps, filters, precipitators, and any other device used to capture particulate

emissions.

(8) Miscellaneous Items Used in Above Systems

(i) Electronic controls.

(ii) Vacuum, temperature, and time sensitive valves and switches.

(iii) Hoses, belts, connectors, and assemblies.

Techtronics Industries North America, Inc., will furnish with each new engine written

instructions for its maintenance and use by the owner.

TECHTRONICS INDUSTRIES NORTH AMERICA, INC., LIMITED WARRANTY STATEMENT FOR FEDERAL AND CALIFORNIA

EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES

YOUR WARRANTY RIGHTS AND OBLIGATIONS

3 — Français

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :

Lire et veiller à bien comprendre toutes les instructions. Le

non respect des instructions ci-dessous peut entraîner un

choc électrique, un incendie et / ou des blessures graves.

LIRE TOUTES LES INSTRUCTIONS

 Pour travailler en toute sécurité, lire et veiller à bien

comprendre toutes les instructions avant d’utiliser ce

produit. Respecter toutes les instructions de sécurité. Le

non respect des instructions de sécurité ci-dessous peut

entraîner des blessures graves.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cet outil.

 Ne jamais lancer ou faire tourner le moteur dans un endroit

clos ou mal aéré. Les gaz d’échappement peuvent être

mortels.

 Déblayer la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre

brisé, clous, fils métalliques, cordes, etc. risquant d’être

projetés ou de se prendre dans la ligne de coupe ou la

lame.

 Toujours porter une protection oculaire certifiée conforme

à la norme ANSI Z87.1 ainsi qu’un protection auditive lors

de l’utilisation de ce produit.

 Porter des pantalons longs, manches longues, des

chaussures de travail et des gants épais. Ne pas porter

de vêtements amples, bijoux, shorts, sandales et ne pas

travailler pieds nus. Ne porter aucun bijou.

 Le fait de porter des vêtements de protection lourds

peut augmenter la fatigue de l’utilisateur, ce qui pourrait

entraîner un coup de chaleur. Si le temps est chaud et

humide, effectuer les gros travaux le matin ou en fin

d’après-midi, alors qu’il fait plus frais.

Les produits utilisés sur les territoires des services

forestiers des États-Unis et de certains états doivent être

conformes aux réglementations de lutte contre l’incendie.

Cet outil est doté d’un pare-étincelles, toutefois, d’autres

dispositifs peuvent être requis. Consulter les autorités

locales et gouvernementales.

 Ne jamais utiliser cet outil en le tenant du côté gauche.

 Attacher les cheveux longs pour les maintenir au-dessus

des épaules, afin qu’ils ne se prennent pas dans les pièces

en mouvement.

 Garder les badauds, enfants et visiteurs à une distance de

15 m (50 pi). Recommander aux personnes présente de

porter une protection oculaire. Si quelqu’un s’approche

pendant l’utilisation de l’outil, arrêter le moteur et

l’accessoire de coupe. Le risque de blessure est accru

si on utilise un outil à lames. En effet, les personnes se

trouvant à proximité risquent d’être heurtés par une lame

en marche advenant qu’elle ricoche, ou à la suite de toute

autre réaction inattendue de la scie.

 Ne pas utiliser cet outil en état de fatigue, si l’on est

souffrant ou sous l’influence de l’alcool, de drogues ou

de médicaments.

 Ne pas travailler sous un éclairage insuffisant.

 Se tenir bien campé et en équilibre. Ne pas travailler hors

de portée. Le travail hors de portée risque de faire perdre

l’équilibre ou de causer un contact avec les pièces brûlantes.

 Garder toutes les parties du corps à l’écart des pièces

en mouvement.

 Pour éviter le contact avec les parties brûlantes, ne jamais

travailler avec le bas du moteur au-dessus du niveau de

la taille.

Ne pas toucher les alentours de l’échappement ou du

cylindre, qui deviennent brûlants pendant l’utilisation.

Contact avec les surfaces chaudes pourrait entraîner des

blessures graves.

 Toujours arrêter le moteur et débrancher le fil de la bougie

avant d’effectuer tout entretien ou réglage, à l’exception

des réglages du carburateur.

 Inspecter l’outil avant chaque utilisation pour s’assurer qu’il

n’y a pas de pièces desserrées, de fuites ce carburant,

etc. Remplacer les pièces endommagées avant utilisation.

 Lors d’une utilisation normale, l’accessoire de coupe ne

doit jamais tourner au ralenti. La rotation au ralenti est

toutefois permise lors du réglage du carburateur.

 Il a été rapporté que, chez certaines personnes, les

vibrations produites par les outils à main motorisés peuvent

contribuer au développement d’une affection appelée

syndrome de Raynaud. Les symptômes peuvent inclure

des picotements, l’insensibilisation et le blanchissement

des doigts et sont habituellement provoqués par

l’exposition au froid. L’hérédité, l’exposition au froid et à

l’humidité, le régime alimentaire, la fumée et les habitudes

de travail sont tous des facteurs considérés comme

contribuant au développement de ces symptômes. Il

n’existe actuellement aucune preuve qu’un certain type de

vibration ou le degré d’exposition contribue réellement au

développement de cette affectation. Certaines mesures,

susceptibles de réduire les effets des vibrations, peuvent

être prises par l’opérateur :

a) Garder le corps au chaud par temps froid. Pendant

l’utilisation, porter des gants afin de tenir les mains et

les poignets au chaud. Il a été établi que le froid est

l’une des principales causes du symptôme de Raynaud.

b) Après chaque période d’utilisation, faire des exercices

pour accroître la circulation.

c) Faire des pauses fréquentes. Limiter la durée

d’exposition quotidienne.

d) Garder l’outil bien entretenu, toutes les pièces de

boulonnerie serrées et remplacer les pièces usées.

En cas d’apparition de l’un ou plusieurs des symptômes

décrits ci-dessus, cesser d’utiliser l’outil et consulter un

médecin.

La page charge ...

Ryobi CS26 Manuel utilisateur

Marque: Ryobi

Modèle: CS26

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi CS26 User manual
español: Ryobi CS26 Manual de usuario

Ryobi CS26 Manuel utilisateur

Ce manuel convient également à

Ryobi CS26 Manuel utilisateur

dans d''autres langues

Documents connexes