Genie ALADDIN CONNECT Mode d'emploi

Marque: Genie

Modèle: ALADDIN CONNECT

Catégorie: Porte de garage

Taper: Mode d'emploi

Wall Button Wire

Photocell wire

Power Pack

Aladdin Connect®

Control Wire

Quick Set-up Guide

®WARNING

TO REDUCE THE RISK OF SEVERE INJURY

OR DEATH, READ AND FOLLOW ALL

INSTRUCTIONS.

1. NEVER let children operate or play with the

door controls.

2. Keep remote away from children.

3. Locate the wall control button: A) Within sight

of door. B) At a minimum height of 5 feet, so

small children cannot reach it.

4. Install the entrapment WARNING label next

to the wall button or console, in a prominent

location.

5. NO ONE SHOULD CROSS THE PATH OF THE

MOVING DOOR.

6. NEVER GO UNDER A STOPPED, PARTIALLY

OPEN DOOR.

7. The Aladdin Connect® operating system is

designed for unattended operation. The door

could move unexpectedly.

8. DO NOT install Aladdin Connect® on garage

door openers manufactured prior to 1993

without photocell non-contact safety sensors.

9. DO NOT install on one-piece doors

10. 10. Install DCM in a location where it can be seen Install DCM in a location where it can be seen

and heard while standing in the door opening and heard while standing in the door opening

with the door in the open position.with the door in the open position.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY

INSTRUCTIONS AVERTISSEMENT

POUR RÉDUIRE LE RISQUE DE BLESSURES

GRAVES VOIRE MORTELLES, LIRE ET

COMPRENDRE TOUTES LES INSTRUCTIONS.

1. NE JAMAIS laisser les enfants utiliser ou jouer avec les

commandes de l’ouvre-porte.

2. Tenir les télécommandes hors de la portée des

enfants.

3. Localiser le bouton de la console murale: A) En vue

de la porte. B) À une hauteur minimale de 1,5m an

que les jeunes enfants ne puissent pas l’atteindre.

4. Placer l’étiquette d’AVERTISSEMENT en cas de

coinçage à proximité du bouton mural ou de la

console murale de manière à ce qu’elle soit bien en

évidence.

5. NE JAMAIS PASSER SOUS LA PORTE EN MOUVEMENT.

6. NE JAMAIS PASSER SOUS UNE PORTE À L’ARRÊT

PARTIELLEMENT OUVERTE.

7. Le système d’exploitation Aladdin Connect® a été

conçu pour fonctionner sans surveillance. La porte

peut se déplacer de façon inattendue.

8. NE PAS installer Aladdin Connect® sur les ouvre-

portes de garage fabriqués avant 1993, sans capteurs

de sécurité photoélectrique sans contact.

9. NE PAS installer sur les portes d’une seule pièce.

10. Installez DCM dans un endroit où il peut être vu et

entendu tout en se tenant dans l’ouverture de la porte

avec la porte en position ouverte.

CONSERVER CES INSTRUCTIONS

CONSIGNES DE SÉCURITÉ

IMPORTANTES

DCM

(Door Control Module) DPS

(Door Position Sensor)

Hardware Bag Power Pack

Wire Spool

Insulated

Staple x30

Included Components

Recommended Tools

Drill & 3/32 Bit

Small Common

Screwdriver

Phillips Head

Screwdriver

Wire Cutters/

Strippers

Hammer

5/16 Wrench or

Nut Driver

For a video of this installation, visit www.GenieCompany.com/AladdinConnect/InstallationVideo

39386.01577, 03/2023

Need help or have questions? Contact Aladdin Connect® Customer Service at 1-866-599-4995

Mon-Fri 9am -8pm EST, Sat 10am - 6pm EST.

Typical Installation shown.

Installations may vary

Scan for the

Aladdin Connect®

installation video

Scan here for additional

Aladdin Connect®

information

WARNING

UNPLUG GARAGE DOOR OPENER PRIOR TO

INSTALLING Aladdin Connect®

Door may operate unexpectedly.

AVERTISSEMENT

DÉBRANCHER L’OUVRE-PORTE DE GARAGE AVANT

D’INSTALLER Aladdin Connect®

La porte peut fonctionner de façon inattendue.

Apple and the Apple logo are trademarks

of Apple Inc., registered in the U.S. and

other countries. App Store is a service

mark of Apple Inc.

Scan for

iOS app

Scan for

Android app

STEP 3 - Download the app.

1. Scan the QR code below or visit the devices app store to start the setup of the Aladdin Connect® device.

Search the app store for Aladdin Connect

2. Follow the instructions in the app to create an account and set up the device and Wi-Fi.

STEP 1 - Determine Mounting Location for DCM

Select a location that meets the following criteria:

• Where the DCM can be seen and heard when door is opening

• Within 5ft of a standard 110v AC power outlet

• Within 25ft from either the garage door opener or a wired wall control button.

The DCM is commonly mounted in the following locations:

• Mount above an outlet in the garage - if near the personnel door, the DCM can

be used as a second wall control button or in place of the existing wall button.

• Mount next to opener near ceiling - you can plug it into the same outlet as the

opener and easily wire the DCM to the opener itself.

Once mounting location has been determined, remove the mounting bracket from

the back of DCM, plug in the powercord to the power outlet and connect the plug

to the DCM.

DCM

Device Wi-Fi signal strength indicator

STEP 2 - Check Wi-Fi coverage

Before beginning, please verify the Wi-Fi signal in the garage.

• Connect smartphone to the home Wi-Fi and walk into the garage.

• Place phone where the DCM will be mounted.

• The Wi-Fi signal strength at that location must be at least two bars.

If there are not at least two bars, try these steps to improve signal strength:

• Make sure that the Wi-Fi router is out in the open (not behind large electronics or

in a cabinet).

• Move the Wi-Fi router closer to the garage.

• Purchase a Wi-Fi extender, available at most electronics stores.

STEP 4 - Wiring the DCM (Single Door Install Shown with Genie Opener)

Before you begin, make sure the garage door opener is unplugged so the door does not move

unexpectedly.

1. Leaving the wire spool intact, split one end of the dual strand wire

approximately 2 in. then strip 1/2 in. of insulation (FIG. A)

2. On the terminal strip (back of the DCM), press down on the orange tabs and

insert 1 wire each into each of the two terminals for DOOR 1. Each DOOR number on

the terminal strip corresponds to a button on the front of the panel (FIG. B & C).

Wall Mount

Anchors (as needed)

Perforated Angle

Mount

1/2"

Press tab down Press tab down

to install wire.to install wire.

STEP 6

Mount and Power Aladdin Connect®:

1. Using the DCM mounting bracket as a template at the optimal

Wi-Fi location. Mark and drill 2-3/32” pilot holes and mount

bracket to wall using supplied screws. If mounting to drywall,

use anchors provided in kit or if mounting to perforated angle

at opener location, use nuts, washers and screws provided.

2. Plug Power Pack into wall outlet. An extended screw is provided

to secure Power Pack to outlet if needed.

3. Plug Power Pack into back of DCM as shown in STEP 1.

NOTE: LEDs on DCM will ash momentarily as it reacquires signals.

4. Snap DCM onto mounting bracket.

5. Route wires and secure with supplied staples.

6. Ax the warning placard next to wall control or DCM in plain

sight to signify that the door will operate remotely.

7. Tacks or staples should be used if the placard does not adhere

to the mounting surface.

STEP 7

Mount DPS Module to Garage Door:

DO NOT remove the battery “PULL TAB” from DPS until

directed by the app.

The DPS should be mounted on the TOP door panel only.

Mount to steel reinforced end stile on the far left or right

under the top hinge. DO NOT mount to unreinforced door

panel.

1. Clean door where DPS will mount.

2. Install double sided tape to back of mounting bracket and ax to

door.

NOTE: Double sided tape is designed to hold bracket in place temporarily

only. Not to be used for permanent mounting.

3. Pre-drill 2 - 3/32 holes. DO NOT drill all the way through door.

4. Use included self tapping screws to mount DPS bracket to top door

panel end stile.

5. Slide DPS down onto mounting bracket. DPS should snap onto

bracket.

NOTE: The DPS included with this kit is already programmed to the DCM. See

the NOTE under STEP 8 regarding additional sensors (DPS).

STEP 8

Complete the Programming:

1. Restore power to the garage door opener.

2. Operate the door with the wall control. Open the Aladdin Connect app and verify that the door position in the app is accurate.

NOTE: This kit includes one DPS for use with one door only. The DPS included is already programmed to the DCM . Additional sensors can be purchased separately

from your local Genie retailer. To program additional sensors, rst complete STEP 8 initial setups and programming, then go to “Add a Door Sensor” under the “Doors”

tab inside the app or view the installation video at www.GenieCompany.com/AladdinConnect/InstallationVideo.

NOTE: A white light will ash and an audible beep will sound as an indication that the door is about to move when commanded by the Aladdin Connect® or other

compatible app(s).

END STILE

Garage Door Garage Door

Mounting DPS

Sensor

Door

FIG.A

Button & Connection Detail

FIG. B

Split 2” & Strip 1/2”

One Door Drive, Mt. Hope, OH 44660, USA

1-year warranty,

visit www.geniecompany.com

for details.

Pat. www.geniecompany.com/patents

112612.0001

WARNING

AVERTISSEMENT

MOVING DOOR can cause serious

injury or death.

MOUVEMENT PORTE peut causer des

blessures graves ou la mort.

STAND CLEAR!

Door could close automatically.

Do Not stop or stand in doorway

SE TENIR À L'ÉCART DE LA PORTE!

La porte pourrait se refermer automatiquement.

Ne pas arrêter ou debout dans la porte.

Use of this product, the software embedded within this product and the related application software is subject to the Terms and Conditions available at: www.GenieCompany.com/AladdinConnect

2-4

FIG.C

NOTE: This Wi-Fi retrot kit can control

up to 3 garage door openers.

STEP 5a - Option 1 - Wiring to Wired Wall Control

There are two ways to wire the DCM for power. Please review Options 1 and 2 for

Wiring steps.

1. Remove the wall control push button and locate screw terminals on the

back.

2. Cut the dual wire strand and split the end ~2 in. and then l strip 1/2 in. of

insulation (FIG. A)

3. Add the black/white wire from the DCM to the screw with the black/white