Genie ALADDIN CONNECT Mode d'emploi

Catégorie
Porte de garage
Taper
Mode d'emploi
Wall Button Wire
Photocell wire
Power Pack
Aladdin Connect®
Control Wire
Quick Set-up Guide
®WARNING
TO REDUCE THE RISK OF SEVERE INJURY
OR DEATH, READ AND FOLLOW ALL
INSTRUCTIONS.
1. NEVER let children operate or play with the
door controls.
2. Keep remote away from children.
3. Locate the wall control button: A) Within sight
of door. B) At a minimum height of 5 feet, so
small children cannot reach it.
4. Install the entrapment WARNING label next
to the wall button or console, in a prominent
location.
5. NO ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.
6. NEVER GO UNDER A STOPPED, PARTIALLY
OPEN DOOR.
7. The Aladdin Connect® operating system is
designed for unattended operation. The door
could move unexpectedly.
8. DO NOT install Aladdin Connect® on garage
door openers manufactured prior to 1993
without photocell non-contact safety sensors.
9. DO NOT install on one-piece doors
10. 10. Install DCM in a location where it can be seen Install DCM in a location where it can be seen
and heard while standing in the door opening and heard while standing in the door opening
with the door in the open position.with the door in the open position.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS AVERTISSEMENT
POUR RÉDUIRE LE RISQUE DE BLESSURES
GRAVES VOIRE MORTELLES, LIRE ET
COMPRENDRE TOUTES LES INSTRUCTIONS.
1. NE JAMAIS laisser les enfants utiliser ou jouer avec les
commandes de l’ouvre-porte.
2. Tenir les télécommandes hors de la portée des
enfants.
3. Localiser le bouton de la console murale: A) En vue
de la porte. B) À une hauteur minimale de 1,5m an
que les jeunes enfants ne puissent pas l’atteindre.
4. Placer l’étiquette d’AVERTISSEMENT en cas de
coinçage à proximité du bouton mural ou de la
console murale de manière à ce qu’elle soit bien en
évidence.
5. NE JAMAIS PASSER SOUS LA PORTE EN MOUVEMENT.
6. NE JAMAIS PASSER SOUS UNE PORTE À LARRÊT
PARTIELLEMENT OUVERTE.
7. Le système d’exploitation Aladdin Connect® a été
conçu pour fonctionner sans surveillance. La porte
peut se déplacer de façon inattendue.
8. NE PAS installer Aladdin Connect® sur les ouvre-
portes de garage fabriqués avant 1993, sans capteurs
de sécurité photoélectrique sans contact.
9. NE PAS installer sur les portes d’une seule pièce.
10. Installez DCM dans un endroit où il peut être vu et
entendu tout en se tenant dans louverture de la porte
avec la porte en position ouverte.
CONSERVER CES INSTRUCTIONS
CONSIGNES DE SÉCURITÉ
IMPORTANTES
DCM
(Door Control Module) DPS
(Door Position Sensor)
Hardware Bag Power Pack
Wire Spool
Insulated
Staple x30
Included Components
Recommended Tools
Drill & 3/32 Bit
Small Common
Screwdriver
Phillips Head
Screwdriver
Wire Cutters/
Strippers
Hammer
5/16 Wrench or
Nut Driver
For a video of this installation, visit www.GenieCompany.com/AladdinConnect/InstallationVideo
39386.01577, 03/2023
Need help or have questions? Contact Aladdin Connect® Customer Service at 1-866-599-4995
Mon-Fri 9am -8pm EST, Sat 10am - 6pm EST.
Typical Installation shown.
Installations may vary
Scan for the
Aladdin Connect®
installation video
Scan here for additional
Aladdin Connect®
information
WARNING
UNPLUG GARAGE DOOR OPENER PRIOR TO
INSTALLING Aladdin Connect®
Door may operate unexpectedly.
AVERTISSEMENT
DÉBRANCHER LOUVRE-PORTE DE GARAGE AVANT
D’INSTALLER Aladdin Connect®
La porte peut fonctionner de façon inattendue.
Apple and the Apple logo are trademarks
of Apple Inc., registered in the U.S. and
other countries. App Store is a service
mark of Apple Inc.
Scan for
iOS app
Scan for
Android app
STEP 3 - Download the app.
1. Scan the QR code below or visit the devices app store to start the setup of the Aladdin Connect® device.
Search the app store for Aladdin Connect
2. Follow the instructions in the app to create an account and set up the device and Wi-Fi.
STEP 1 - Determine Mounting Location for DCM
Select a location that meets the following criteria:
Where the DCM can be seen and heard when door is opening
Within 5ft of a standard 110v AC power outlet
Within 25ft from either the garage door opener or a wired wall control button.
The DCM is commonly mounted in the following locations:
Mount above an outlet in the garage - if near the personnel door, the DCM can
be used as a second wall control button or in place of the existing wall button.
Mount next to opener near ceiling - you can plug it into the same outlet as the
opener and easily wire the DCM to the opener itself.
Once mounting location has been determined, remove the mounting bracket from
the back of DCM, plug in the powercord to the power outlet and connect the plug
to the DCM.
DCM
Device Wi-Fi signal strength indicator
STEP 2 - Check Wi-Fi coverage
Before beginning, please verify the Wi-Fi signal in the garage.
Connect smartphone to the home Wi-Fi and walk into the garage.
Place phone where the DCM will be mounted.
The Wi-Fi signal strength at that location must be at least two bars.
If there are not at least two bars, try these steps to improve signal strength:
Make sure that the Wi-Fi router is out in the open (not behind large electronics or
in a cabinet).
Move the Wi-Fi router closer to the garage.
Purchase a Wi-Fi extender, available at most electronics stores.
STEP 4 - Wiring the DCM (Single Door Install Shown with Genie Opener)
Before you begin, make sure the garage door opener is unplugged so the door does not move
unexpectedly.
1. Leaving the wire spool intact, split one end of the dual strand wire
approximately 2 in. then strip 1/2 in. of insulation (FIG. A)
2. On the terminal strip (back of the DCM), press down on the orange tabs and
insert 1 wire each into each of the two terminals for DOOR 1. Each DOOR number on
the terminal strip corresponds to a button on the front of the panel (FIG. B & C).
Wall Mount
Anchors (as needed)
Perforated Angle
Mount
1/2"
2"
Press tab down Press tab down
to install wire.to install wire.
STEP 6
Mount and Power Aladdin Connect®:
1. Using the DCM mounting bracket as a template at the optimal
Wi-Fi location. Mark and drill 2-3/32” pilot holes and mount
bracket to wall using supplied screws. If mounting to drywall,
use anchors provided in kit or if mounting to perforated angle
at opener location, use nuts, washers and screws provided.
2. Plug Power Pack into wall outlet. An extended screw is provided
to secure Power Pack to outlet if needed.
3. Plug Power Pack into back of DCM as shown in STEP 1.
NOTE: LEDs on DCM will ash momentarily as it reacquires signals.
4. Snap DCM onto mounting bracket.
5. Route wires and secure with supplied staples.
6. Ax the warning placard next to wall control or DCM in plain
sight to signify that the door will operate remotely.
7. Tacks or staples should be used if the placard does not adhere
to the mounting surface.
STEP 7
Mount DPS Module to Garage Door:
DO NOT remove the battery PULL TAB from DPS until
directed by the app.
The DPS should be mounted on the TOP door panel only.
Mount to steel reinforced end stile on the far left or right
under the top hinge. DO NOT mount to unreinforced door
panel.
1. Clean door where DPS will mount.
2. Install double sided tape to back of mounting bracket and ax to
door.
NOTE: Double sided tape is designed to hold bracket in place temporarily
only. Not to be used for permanent mounting.
3. Pre-drill 2 - 3/32 holes. DO NOT drill all the way through door.
4. Use included self tapping screws to mount DPS bracket to top door
panel end stile.
5. Slide DPS down onto mounting bracket. DPS should snap onto
bracket.
NOTE: The DPS included with this kit is already programmed to the DCM. See
the NOTE under STEP 8 regarding additional sensors (DPS).
STEP 8
Complete the Programming:
1. Restore power to the garage door opener.
2. Operate the door with the wall control. Open the Aladdin Connect app and verify that the door position in the app is accurate.
NOTE: This kit includes one DPS for use with one door only. The DPS included is already programmed to the DCM . Additional sensors can be purchased separately
from your local Genie retailer. To program additional sensors, rst complete STEP 8 initial setups and programming, then go to “Add a Door Sensor” under the “Doors”
tab inside the app or view the installation video at www.GenieCompany.com/AladdinConnect/InstallationVideo.
NOTE: A white light will ash and an audible beep will sound as an indication that the door is about to move when commanded by the Aladdin Connect® or other
compatible app(s).
END STILE
Garage Door Garage Door
Mounting DPS
Sensor
Door
1
Door
2
Door
3
FIG.A
Button & Connection Detail
FIG. B
Split 2” & Strip 1/2”
©2023 The Genie Company
One Door Drive, Mt. Hope, OH 44660, USA
1-year warranty,
visit www.geniecompany.com
for details.
Pat. www.geniecompany.com/patents
112612.0001
WARNING
AVERTISSEMENT
MOVING DOOR can cause serious
injury or death.
MOUVEMENT PORTE peut causer des
blessures graves ou la mort.
STAND CLEAR!
Door could close automatically.
Do Not stop or stand in doorway
SE TENIR À L'ÉCART DE LA PORTE!
La porte pourrait se refermer automatiquement.
Ne pas arrêter ou debout dans la porte.
OR
Use of this product, the software embedded within this product and the related application software is subject to the Terms and Conditions available at: www.GenieCompany.com/AladdinConnect
1
2-4
6
FIG.C
NOTE: This Wi-Fi retrot kit can control
up to 3 garage door openers.
STEP 5a - Option 1 - Wiring to Wired Wall Control
There are two ways to wire the DCM for power. Please review Options 1 and 2 for
Wiring steps.
1. Remove the wall control push button and locate screw terminals on the
back.
2. Cut the dual wire strand and split the end ~2 in. and then l strip 1/2 in. of
insulation (FIG. A)
3. Add the black/white wire from the DCM to the screw with the black/white
wire on the wall control.
4. Add the white/white wire from the DCM to the other screw on the wall control.
NOTE: Wires are polarity sensitive at the wall console terminals.
Check your opener manual to review proper terminal wiring as needed.
FIG. D
to DCM.
to opener
STEP 5b - Option 2 - Wiring to Garage Door Opener
1. Find the terminals for the push button wired wall console
a. If your garage door opener has screw terminals, connect one wire to the
push button terminal and the other to the common (comm) terminal.
b. If your garage door opener has colored terminals, wire to the red and
white terminals (or R and W).
NOTE: Garage door openers have terminal strips or screw terminals to connect to
safety beams (STB or Beam) AND to the wall control push button (PB or also called
a basic wall control - BWC). The wiring from the door control module connects with
existing wires going to the wall control push button terminals. You can review the
garage door opener manual to see which terminals are for the push button or just
trace the wire from the push button to the opener.
Scan for the
Aladdin Connect®
installation video
Scan here for additional
Aladdin Connect®
information
P.B. COM. BEAM
Need help? Call us at 1-866-599-4995 or
scan the QR codes for additional support.
  • Page 1 1
  • Page 2 2

Genie ALADDIN CONNECT Mode d'emploi

Catégorie
Porte de garage
Taper
Mode d'emploi

dans d''autres langues