Dell PowerVault DP500 Guide de démarrage rapide

Dell™ PowerVault™ 500 Systems

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Dell™ PowerVault™ 500 Systems

Getting Started

With Your System

Model EMS01

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your system.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Inc.;

Intel and Xeon are registered trademarks of Intel Corporation in the U. S. and other countries;

Microsoft, Windows, and Windows Server are either trademarks or registered trademarks of

Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks

and trade names other than its own.

Model EMS01

November 2007 P/N YX154 Rev. A00

Contents 3

Contents

System Features . . . . . . . . . . . . . . . . . . . . . . 5

Supported Operating Systems

. . . . . . . . . . . . . . . 7

Other Information You May Need

. . . . . . . . . . . . . 7

Obtaining Technical Assistance . . . . . . . . . . . . . 7

Installation and Configuration

. . . . . . . . . . . . . . 8

Install the Rails and System in a Rack

. . . . . . . . 8

Connect the Keyboard, Mouse, and Monitor

. . . . 9

Connect the Power

. . . . . . . . . . . . . . . . . 10

Install the Power Cord Retention Bracket

. . . . . 11

Turn on the System

. . . . . . . . . . . . . . . . . 12

Install the Bezel

. . . . . . . . . . . . . . . . . . 12

Complete the 0perating System Setup

. . . . . . . . . 13

Technical Specifications

. . . . . . . . . . . . . . . . 13

4 Contents

Getting Started With Your System 5

System Features

The major hardware and software features of your system include:

• One or two Dual-Core Intel

®

Xeon

®

Processors 5000 Sequence.

• Support for symmetric multiprocessing (SMP), which is available on

systems with two Intel Xeon processors. SMP greatly improves overall

system performance by dividing processor operations between

independent processors. To take advantage of this feature, you must use

an operating system that supports multiprocessing.

NOTE: If you decide to upgrade your system by installing a second processor,

you must order the processor upgrade kits from Dell™. Not all versions of

the Intel Xeon processor will work properly as additional processors. The

upgrade kit from Dell contains the correct version of the processor, heat sink,

and fan as well as the instructions for performing the upgrade.

• A minimum of 512 MB of 533- or 667- MHz (when available), Fully

Buffered DIMMs (FBD), upgradable to a maximum of 32 GB by installing

combinations of 256-MB, 512-MB, 1-GB, 2-GB, or 4-GB memory modules

in the eight memory module sockets on the system board.

The system also features redundant memory, which provides memory

sparing or memory mirroring. Either feature is available if eight identical

memory modules are installed.

• Support for up to six 3.5-inch, internal hot-pluggable Serial Attached SCSI

(SAS) or SATA hard drives without optional media bay, or up to four 3.5-inch

internal hot-pluggable SAS or SATA hard drives with optional media bay.

• The optional media bay (available only with the 3.5-inch x4 backplane

configurations) provides support for an optional half-height tape backup

unit (TBU) and an optional single, 1.44-MB, 3.5-inch diskette drive.

• An optional slim-line IDE CD, DVD, or combination CD-RW/DVD drive.

NOTE: DVD devices are data only.

• A chassis intrusion switch that signals the appropriate systems

management software if the top cover is opened.

• Up to two hot-pluggable, 750-W power supplies in an optional 1 + 1

redundant configuration.

• Four hot-pluggable system cooling fans.

6 Getting Started With Your System

The system board includes the following features:

• One of the following left riser card options:

– A left riser card that has one full-length PCIe x8 lane slot

and one full-length PCIe x4 lane slot.

OR

– A left riser card that has two full-length PCI-X 3.3-V, 64-bit,133-MHz

slots on separate PCI-X buses (capable of throttling back to support

legacy PCI add-in cards).

• A center riser card that has one half-length PCIe x8 lane slot.

• Dedicated slot for an integrated SAS host bus adapter or an optional RAID

controller card with 256 MB of cache memory and a RAID battery.

The internal channel supports up to six 3.5-inch SATA hard drives.

NOTE: System boot is not supported from an external device attached

to a SAS or SCSI adapter, including SAS 5/E, PERC 5/E, or PERC 4e/DC.

See support.dell.com for the latest support information about booting

from external devices.

• Two integrated Gigabit Ethernet NICs, capable of supporting 10-Mbps,

100-Mbps, and 1000-Mbps data rates.

• Four USB 2.0-compliant connectors (two on the front and two on the back)

capable of supporting a diskette drive, a CD-ROM drive, a keyboard,

a mouse, or a USB flash drive.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem with an ATI ES1000, 33-MHz

PCI video controller. This video subsystem contains 16 MB of DDR SDRAM

video memory (nonupgradable). Maximum resolution is 1600 x 1200 with

64 K colors; true-color graphics are supported in the following resolutions:

640 x 480, 800 x 600, 1024 x 768, 1152 x 864, and 1280 x 1024. When

the optional RAC is installed, the video resolution is 1280 X 1024.

• Systems management circuitry that monitors operation of the system fans as

well as critical system voltages and temperatures. The systems management

circuitry works in conjunction with the systems management software.

• Standard baseboard management controller with serial access.

• Back-panel connectors include one serial, one video, two USB,

and two NIC connectors.

Getting Started With Your System 7

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see "Technical Specifications"

on page 13.

Supported Operating Systems

• Microsoft

®

Windows

®

Storage Server 2003 R2 Workgroup, Standard,

and Enterprise x64 Editions with SP2

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

• The

Rack Installation Instructions

or

Rack Installation Guide

included

with your rack solution describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. This document may be found on the CDs

that came with your system, or on

support.dell.com

.

• CDs included with your system provide documentation and tools

for configuring and managing your system.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system

does not perform as expected, see your Hardware Owner’s Manual.

Dell™ Enterprise Training and Certification is available; see

www.dell.com/training for more information. This service may not be offered

in all locations.

8 Getting Started With Your System

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety

instructions and important regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Install the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack installation

documentation for your system, install the rails and the system in the rack.

See your rack installation documentation for instructions on installing

your system in a rack.

Getting Started With Your System 9

Connect the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating

which cable to plug into each connector. Be sure to tighten the screws

(if any) on the monitor's cable connector.

10 Getting Started With Your System

Connect the Power

Connect the monitor (optional) and system power, and connect the system’s

power cable(s) to the system. If your system has an expansion card with a

video output connector, do not connect the monitor to system’s integrated

video connector. Instead, connect the monitor cable to the connector on

the expansion card.

Plug the other end of the cable into a grounded electrical outlet or a separate

power source such as an uninterrupted power supply (UPS) or a power

distribution unit (PDU).

Getting Started With Your System 11

Install the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power

supply handle. Bend the system power cable into a loop as shown in the

illustration and attach to the bracket’s cable clasp. Repeat the procedure

for the second power supply.

Plug the other end of the power cables into a grounded electrical outlet

or a separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

12 Getting Started With Your System

Turn on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power indicators

should light. Adjust the monitor's controls until the displayed image is

satisfactory.

Install the Bezel

Install the bezel (optional).

Getting Started With Your System 13

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the Quick Installation Guide. Be sure the operating system

is installed before installing hardware or software not purchased with the system.

Technical Specifications

Processor

Processor type One or two Dual-Core Intel Xeon

Processors 5000 Sequence.

Expansion Bus

Bus type PCI-X, PCIe

Expansion slots

Center riser:

PCIe

one half-height x8 lane 3.3-V (slot 1)

Left riser

PCI-X option:

PCIe option:

two full-height, full-length 3.3-V, 64-bit,

133-MHz (slots 2 and 3)

OR

one full-height x8 lane 3.3-V (slot 2)

and one full-height x4 lane 3.3-V (slot 3)

Memory

Architecture 533 or 667 (when available) MHz Fully

Buffered DIMMs (FBD)

Memory module sockets eight 240-pin

Memory module capacities 256 MB, 512 MB, 1 GB, 2 GB, or 4 GB

Minimum RAM 512 MB (two 256-MB modules)

Maximum RAM 32 GB

14 Getting Started With Your System

Drives

Hard drives up to six 3.5-inch, internal hot-

pluggable SAS or SATA hard drives

without optional media bay,

OR

up to four 3.5-inch internal hot-

pluggable SAS or SATA hard drives

with optional media bay

Diskette drive one optional 3.5-inch, 1.44-MB

external optional USB 3.5-inch, 1.44-MB

Optical drive one optional slimline IDE

CD, DVD,

or combination CD-RW/DVD

NOTE:

DVD devices are data only.

external optional USB CD

Tape drive one optional internal half height tape

backup device

Flash drive external optional USB

Connectors

Back

NIC

Two RJ-45 (for integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Video

Video type ATI ES1000 video controller; VGA

connectors

Video memory 16 MB of DDR SDRAM

Getting Started With Your System 15

Power

AC power supply (per power supply)

Wattage

750 W

Voltage

85–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2697 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over

the entire system ambient operating

range, the inrush current may reach 55 A

per power supply for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Physical

Rack

Height

8.656 cm (3.40 in)

Width

44.7 cm (17.6 in)

Depth

75.68 cm (29.79 in)

Weight (maximum configuration)

26.76 kg (59 lb)

16 Getting Started With Your System

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a

maximum temperature gradation

of 10°C per hour

Storage

–40° to 65°C (–40° to 149°F) with

a maximum temperature gradation

of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a

maximum humidity gradation of 10%

per hour

Storage

5% to 95% (noncondensing) with a

maximum humidity gradation of 10%

per hour

Maximum vibration

Operating

0.25 G at 3–200 Hz for 15 min

Storage

0.5 G at 3–200 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system)

of 41 G for up to 2 ms

Storage

Six consecutively executed shock pulses

in the positive and negative x, y, and z

axes (one pulse on each side of the

system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Systèmes Dell™ PowerVault™ 500

Guide de mise en route

Modèle EMS01

Remarques, avis et précautions

REMARQUE : Une REMARQUE indique des informations importantes qui peuvent

vous aider à mieux utiliser votre système.

AVIS : un AVIS vous avertit d'un risque de dommage matériel ou de perte

de données et vous indique comment éviter le problème.

PRÉCAUTION : le message ATTENTION indique une situation potentiellement

dangereuse qui, si elle n'est pas évitée, peut provoquer une détérioration

du matériel ou des blessures pouvant entraîner la mort.

____________________

Les informations contenues dans ce document peuvent être modifiées sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.

est strictement interdite.

Marques utilisées dans ce document : Dell, le logo DELL et PowerVault sont des marques de Dell

Inc. ; Intel et Xeon sont des marques déposées de Intel Corporation aux États-Unis et/ou dans d'autres

pays ; Microsoft, Windows et Windows Server sont des marques déposées déposées ou non de

Microsoft Corporation aux États-Unis et/ou dans d'autres pays.

Tous les autres noms de marques et marques commerciales utilisés dans ce document se rapportent

aux sociétés propriétaires des marques et des noms de ces produits. Dell Inc. décline tout intérêt dans

l'utilisation des marques déposées et des noms de marques ne lui appartenant pas.

Modèle EMS01

Novembre 2007 N/P YX154 Rév. A00

La page charge ...

Dell PowerVault DP500 Guide de démarrage rapide

Dell PowerVault DP500 Guide de démarrage rapide

dans d''autres langues

Documents connexes