TEAC CD-H750 Le manuel du propriétaire
- Catégorie
- Lecteur CD
- Taper
- Le manuel du propriétaire
ENGLISH
Z
FRANÇAIS
ESPAÑOL
OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DEL USUARIO
Compact Disc Player
CD-H750
CQX1A1710Z
2
CAUTION
o
DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO
EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS
ARE INSIDE.
o
IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE
PRODUCT UNTIL IT HAS BEEN REPAIRED.
o
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
IN NORTH AMERICA USE ONLY ON 120 V SUPPLY.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
For Canada
Industry Canada’s Compliance Statement:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
For U.S.A.
This equipment complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions: 1) This device may not
cause interference and 2) This device must accept any interference,
including interference that may cause undesired operation of the
device.
Information to the user:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the equipment and/or the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
CAUTION
Changes or modifications to this equipment not expressly approved
by TEAC CORPORATION for compliance will void the user’s warranty.
IMPORTANT SAFETY PRECAUTIONS
Supply of this product does not convey a license nor imply any right to distribute MPEG Layer-3 compliant content created with this product
in revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), streaming applications (via Internet, in-
tranets and/or other networks), other content distribution systems (pay-audio or audio-on-demand applications and the like) or on physical me-
dia (compact discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like).
An independent license for such use is required. For details, please visit http://mp3licensing.com.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is pro-
hibited without a license from Microsoft.
"Made for iPod" and "Made for iPhone" mean that an electronic accessory has been designed to connect specically to iPod or iPhone, respec-
tively, and has been certied by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone may aect wireless performance.
Apple and iPod are trademarks of Apple Inc., registered in the U.S. and other countries.
Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.
3
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8)
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
o
The apparatus draws nominal non-operating power from the AC
outlet with its POWER or STANDBY/ON switch not in the ON position.
o
The mains plug is used as the disconnect device, the disconnect
device shall remain readily operable.
o
Caution should be taken when using earphones or headphones
with the product because excessive sound pressure (volume) from
earphones or headphones can cause hearing loss.
o
Do not expose this apparatus to drips or splashes.
o
Do not place any objects filled with liquids, such as vases, on
the apparatus.
o
Do not install this apparatus in a confined space such as a book
case or similar unit.
o
The apparatus should be located close enough to the AC outlet
so that you can easily reach the power cord plug at any time.
o
If the product uses batteries (including a battery pack or
installed batteries), they should not be exposed to sunshine, fire
or excessive heat.
o
CAUTION for products that use replaceable lithium batteries: there
is danger of explosion if a battery is replaced with an incorrect
type of battery. Replace only with the same or equivalent type.
Products with Class construction are equipped with a power
supply cord that has a grounding plug. The cord of such a product
must be plugged into an AC outlet that has a protective
grounding connection.
CAUTION
WARNING
Q Precautions concerning batteries
Misuse of batteries could cause them to rupture or leak leading
to fire, injury or the staining of nearby things. Please read and
observe the following precautions carefully.
o Be sure to insert the batteries with correct positive (+) and
negative (_) orientations.
o Use batteries of the same type. Never use different types of bat-
teries together.
o If the remote control is not used for a long time (more than a
month), remove the batteries to prevent them from leaking.
o If the batteries leak, wipe away the leakage inside the battery
compartment and replace the batteries with new ones.
o Do not use batteries of types other than those specified. Do not
mix new batteries with old ones or use different types of batter-
ies together.
o Do not heat or disassemble batteries. Never throw batteries into
fire or water.
o Do not carry or store batteries with other metallic objects. The
batteries could short circuit, leak or explode.
o Never recharge a battery unless it is confirmed to be a recharge-
able type.
IMPORTANT SAFETY INSTRUCTIONS
Optical pickup
Type : EP-C101
Manufacturer : Ever Bright Technology and Science
Electronical Co.,Ltd
Laser output : Less than 1mW on the objective lens
Wavelength : 790±25 nm
4
For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed
of separately from the municipal waste stream via collection
facilities designated by the government or local authorities.
(b) By disposing of electrical and electronic equipment
correctly, you will help save valuable resources and prevent
any potential negative effects on human health and the
environment.
(c)
Improper disposal of waste electrical and electronic equipment
can have serious effects on the environment and human health
because of the presence of hazardous substances in the
equipment.
(d)
The Waste Electrical and Electronic Equipment (WEEE)
symbol, which shows a wheeled bin that has been
crossed out, indicates that electrical and electronic
equipment must be collected and disposed of separately
from household waste.
(e)
Return and collection systems are available to end users. For
more detailed information about the disposal of old electrical
and electronic equipment, please contact your city office,
waste disposal service or the shop where you purchased the
equipment.
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be disposed of
separately from the municipal waste stream via collection
facilities designated by the government or local authorities.
(b) By disposing of waste batteries and/or accumulators
correctly, you will help save valuable resources and prevent
any potential negative effects on human health and the
environment.
(c)
Improper disposal of waste batteries and/or accumulators can
have serious effects on the environment and human health
because of the presence of hazardous substances in them.
(d) The WEEE symbol, which shows a wheeled bin that
has been crossed out, indicates that batteries and/
or accumulators must be collected and disposed of
separately from household waste.
If a battery or accumulator contains more than the specified
values of lead (Pb), mercury (Hg), and/or cadmium (Cd)
as defined in the Battery Directive (2006/66/EC), then the
chemical symbols for those elements will be indicated
beneath the WEEE symbol.
(e) Return and collection systems are available to end users.
For more detailed information about the disposal of waste
batteries and/or accumulators, please contact your city office,
waste disposal service or the shop where you purchased
them.
Pb, Hg, Cd
5
ENGLISH
Before use
Read this before operation
< Avoid placing the unit in direct sunlight or close to any source of
heat, such as radiators, heaters, open fireplaces, amplifiers, etc.
Also avoid locations that are subject to vibrations or exposed to
excessive dust, cold or moisture.
< Place the unit in a stable location near the audio system that you
will use.
< Do not move the unit during playback.
< During playback, the disc rotates at high speed. Do not lift or move
the unit during playback. Doing so may damage the disc or the
unit.
< Be careful to avoid injury when moving the unit due to its weight.
Get someone to help you if necessary.
< The voltage supplied to the unit should match the voltage as
printed on the rear panel. If you are in any doubt regarding this
matter, consult an electrician.
< As the unit could become warm during operation, always leave
sufficient space around it for ventilation. When placing this unit,
position it so that it is at least 30 cm (12") from walls and other
devices in order to allow good heat dissipation. When installing
it in a rack, leave at least 30 cm (12") open above and behind the
unit.
< Do not open the cabinet as this might result in damage to the
circuitry or cause electric shock. If a foreign object should get into
the unit, contact your dealer or service company.
< When removing the power plug from the wall outlet, always pull
directly on the plug, never yank on the cord.
< Always remove the disc before relocating or moving this unit.
Moving the unit with a disc inside could cause a malfunction.
< Depending on the electromagnetic waves of television broadcasts,
interference might appear on television screens when this unit’s
power is on. This does not indicate that this unit or the TV is
malfunctioning. If this occurs, put the unit in standby.
DO NOT MOVE THE UNIT DURING PLAYBACK
During playback, the disc rotates at a high speed. Do NOT lift or move
the unit during playback. Doing so may damage the disc.
WHEN MOVING THIS UNIT
When changing the place of installation or packing the unit for
moving, be sure to remove the disc and return the disc table to its
original position in the player. Then, press the STANDBY/ON button to
put the unit in standby, and disconnect the power cord. Moving this
unit with a disc loaded may result in damage to this unit.
Maintenance
If the surface of the unit gets dirty, wipe it with a soft cloth or
use diluted mild liquid soap. Allow the surface of the unit to dry
completely before using.
Q For safety, disconnect the power cord from the socket before
cleaning.
p Never spray liquid directly on this unit.
p Do not use thinner or alcohol as they could damage the surface of
the unit.
p Avoid allowing rubber or plastic materials to touch this product for
long periods of time, because they could damage the cabinet.
Contents
Thank you for choosing TEAC. Read this manual carefully to
get the best performance from this unit.
Before use ........................................................5
Discs .............................................................6
MP3 and WMA ...................................................7
Using an iPod/iPhone ............................................7
USB flash drives ..................................................7
Connections .....................................................8
Part names (main unit) ...........................................9
Part names (remote control) .................................... 10
Remote control unit ............................................11
About the ErP ..................................................12
Basic operation ................................................. 13
Listening to a CD ...............................................14
Listening to files on a USB flash drive ...........................15
Listening to an iPod/iPhone .................................... 16
Playback (1) ....................................................16
Programmed playback (1) ......................................19
Shuffle playback ................................................ 21
Repeat playback ................................................22
Time ........................................................... 23
Display (1) ...................................................... 23
Before recording ............................................... 24
Setting the Recoding Mode ....................................25
Recording to a USB flash drive ..................................26
Deleting a file from a USB flash drive ............................ 27
Restoring factory settings .......................................27
Troubleshooting ...............................................28
Specifications ..................................................29
6
Discs
Discs that can be played by this unit
CDs that bear the “COMPACT disc DIGITAL AUDIO”
logo.
< 12cm (4.7") or 8cm (3.15") discs
< Linear PCM digital audio
Audio CDs are divided into tracks.
CD-R and CD-RW discs that have been correctly
recorded in the audio CD format (CD-DA) and
finalized.
This unit can play these types of discs without an adapter. It cannot
play any other type of disc.
Q Playback of any other disc type could result in an unpleasant loud
noise, damage to the speakers as well as potential harm to your
hearing. Never play back any other type of disc.
< The logo should be on the disc label or the CD jacket.
< DVDs, Video CDs, DVD-ROMs, CD-ROMs and similar types of discs
cannot be played on this unit.
< Copy-protected discs and other discs that do not conform to
the CD standard might not play correctly in this player. If you
use such discs in this unit, TEAC and its subsidiaries will not
be responsible for any consequences or guarantee the quality
of reproduction. If you experience problems with such non-
standard discs, you should contact their issuers.
< Discs created by a CD recorder must be finalized before use with
this unit. If you are uncertain about the handling of a CD-R or
CD-RW disc, please contact the seller of the disc directly.
Depending on disc quality and recording conditions, playback of some
discs might not be possible. Please see the manual for the device that
you used to create the disc.
Handling precautions
< Always insert the disc into the disc tray with the label side up. Only
one side of a Compact Disc can be played or used for recording.
< To remove a disc from its storage case, press down on the center
of the case and lift the disc out, holding it carefully by the edges.
How to remove the disc How to hold the disc
CAUTION
< Do not play any disc that is warped, deformed or damaged.
Playing such discs could cause irreparable harm to the playing
mechanisms.
< While printable CD-R and CD-RW discs utilizing modern printing
technologies are generally acceptable, older systems that use
adhesives to attach paper type labels to the disc surface are not
recommended.
< Do not stick papers or protective sheets on the discs and do not
use any protective coating sprays.
< Never use a stabilizer. Using commercially available CD stabilizers
with this unit will damage the mechanisms and cause them to
malfunction.
< Do not use irregularly-shaped discs (octagonal, heart-shaped,
business-card-size, etc.) CDs with these shapes could damage the
unit.
Storage precautions
< Discs should be returned to their cases after use to avoid dust and
scratches that could cause the laser pickup to “skip”.
< Do not expose discs to direct sunlight or high temperature
and humidity for extended periods. Long exposure to high
temperatures will warp discs.
< CD-R and CD-RW discs are more sensitive to the effects of heat
and ultraviolet rays than ordinary CDs. It is important that they
are not stored in locations where they will be exposed to direct
sunlight. They should also be kept away from sources of heat, such
as radiators and heat-generating electrical devices.
Maintenance
< If a disc becomes dirty, wipe its surface radially from the center
hole outward towards the outer edge with a soft, dry cloth.
< Never clean discs using chemicals such as record sprays, antistatic
sprays and fluids, and thinner. Such chemicals will do irreparable
damage to the disc’s plastic surface.
If you are in any doubt as to the care and handling of a disc, read the
precautions supplied with the disc or contact the disc manufacturer.
7
ENGLISH
This unit has two modes. In Direct Mode, the iPod/iPhone menu
is shown on the iPod/iPhone screen. In Extended Mode, the iPod/
iPhone menu is shown on this unit’s screen. By default, this unit is set
to Direct Mode.
For instructions about how to change this mode, see “Changing the
display mode” on page 24.
Compatible iPod/iPhone models
iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G
iPod touch (1st, 2nd, 3rd and 4th generation)
iPod nano (3rd, 4th, 5th and 6th generation)
< See page 24 for information about the Display mode.
< This unit cannot output video from a connected iPod/iPhone.
< To connect an iPod/iPhone, use the USB cable supplied with the
iPod/iPhone.
< An iPod shuffle connected to this port cannot be played.
Compatible iPod/iPhone Software
In case your iPod/iPhone will not work with CD-H750 or with the
remote control unit, a software update may solve the problem.
Visit the Apple website and download the latest iPod/iPhone
software.
Using an iPod/iPhone
< This unit can play audio files that are on external USB flash drives.*
USB flash drives must be formatted as FAT 16 or FAT 32, but not
NTFS.
* The USB port on this unit only supports USB flash drives (also known
as “thumb drives” and “jump drives”). It does not support standard
USB hard drives.
< When more than 2000 files are recorded on the USB flash drive, the
unit might not be able to play them correctly.
< File names of MP3 or WMA files should be in alphanumeric
characters. This unit cannot display symbols or full-size or double-
byte characters (such as Japanese, Chinese, etc.) correctly. Also, be
sure to use the file extension. (“.mp3” for MP3 files, “.wma” for WMA
files.)
< MP3 files are mono or stereo MPEG-1 Audio Layer 3 format. This
unit can play MP3 files with a sampling frequency of 16 kHz to 48
kHz, and a bit-rate of 8 kbps to 320 kbps.
< This unit can play WMA files with a sampling frequency of 32 kHz,
44.1 kHz or 48 kHz and a bit-rate of 48 kbps to 192 kbps.
WMA stands for Windows Media Audio.
< Audio encoded at 128 kbps should sound close to regular audio
CD quality. Although this player will play lower bit-rate MP3 files,
the sound quality becomes noticeably worse at lower bit-rates.
MP3 and WMA
V
CAUTION
Never put the unit in standby or disconnect a USB flash
drive when it is being accessed, for example, during writing,
playback, recording or the erasure of files.
Doing so could damage the CD-H750 and the connected USB
flash drive.
USB devices that can be used with this unit
This unit can play audio files that are on external USB flash drives*.
* The USB port on this unit only supports USB flash drives (also known
as “thumb drives” and “jump drives”). It does not support standard
USB hard drives.
Compatibility
< Use a USB flash drive with power consumption of less than 500mA.
(When an iPhone is connected, it will be charged at 1A.)
< Some flash memory players that charge from a USB terminal
cannot be used for playback.
< Playable formats: FAT16, FAT32
< NTFS, HFS and HFS+ formats cannot be used.
< Max number of playable folders: 99
< Max number of playable/recordable files: 2000
< Depending on the conditions of a USB flash drive, this unit might
not be able to play the files on it or skipping might occur.
< Do not use devices that have a maximum current consumption of
more than 500 mA.
< Do not use devices that have security functions or other special
functions.
< Do not use devices that have been divided into two or more
partitions.
< Do not use a USB hub between this unit and the USB flash drive.
< Proper operation might not be possible depending on the
characteristics of the device.
< This unit cannot copy or move files that are stored on the USB flash
drive.
Recording
This unit can record sound from CDs to USB flash drives in MP3 format.
See page26 for details.
USB flash drives
8
Connections
A B C
LR
Stereo amplifier or
powered speakers, etc.
DIGITAL IN
(OPTICAL)
DIGITAL IN
(COAXIAL)
Digital audio
input device
RCA audio cable
RCA coaxial digital cable
Optical digital cable
Included power cord
Wall socket
Audio input
(LINE IN, etc.)
CD-H750
CAUTION
< Turn off the power of all the
equipment before making
connections.
< Read the instructions of each
component you intend to use with
this unit.
A
Analog audio output connectors
These RCA jacks output two channels of analog audio signals.
Connect these to an amplifier or other device with audio inputs.
Connect an audio cable's white pin plug to the white (L) jack and
connect its red pin plug to the red (R) jack.
White (L)
Red (R)
White (L)
Red (R)
< Be sure to insert each plug securely.
To prevent humming and interference, avoid bundling the signal
interconnection cables together with the AC power cord or
speaker cables.
B
DIGITAL OUT audio output connectors
Digital 2-channel audio signal is output from this terminal.
When playing back files on a CD, iPod, iPhone or USB flash drive,
these output 44.1kHz/16-bit PCM signals.
Use a commercially-available optical digital cable or RCA coaxial
digital cable to connect this unit with other equipment.
C
Power inlet (~IN)
Insert the included power cord here. After completing all other
connections, insert the power plug into a power outlet.
Unplug the cord from the outlet when not using the unit for a
long time.
Q Use only the included power cord. Use of a different cord
could cause fire or electric shock.
9
ENGLISH
A
Remote sensor
When operating the remote control unit, point it towards the
remote sensor.
B
LEVEL knob
Turn this knob to adjust the volume of the headphones.
C
Disc tray
D
Open/close (L)
Use this button to open and close the disc tray.
E
Skip/Search (.m/,/)
In CD/USB mode, use these buttons to skip tracks/files during
playback or in the stop mode of the CD or USB flash drive.
In iPod mode, use these buttons to skip songs during playback or
in pause mode.
During playback, hold down these buttons to search for a track/file.
F
STANDBY/ON indicator
This lights blue when the power is on.
This lights orange when the unit is in standby.
G
STANDBY/ON
Use this button to turn the unit on or put it in standby mode.
H
PHONES
Connect headphones with a standard 3.5 mm (1/8") stereo plug
here.
Part names (main unit)
BA C D E
G H
I J N OL
K MF
I
Display
J
Stop (H)
Use this button to stop playback and recording.
K
iPod/USB port
Connect an iPod/iPhone or USB flash drive here.
L
Play (G)
Use this button to start playback.
M
CD/USB
Use this button to select CD or USB mode.
Use to select playback of the CD or playback of the USB flash drive
or iPod/iPhone connected to the iPod/USB port.
N
RECORD
Press this button to start recording to a USB flash drive.
Hold down this button to enter the recording setting mode.
O
Pause (J)
Use this button to pause playback.
10
p When both the main unit and the remote control have
buttons with the same functions, this manual explains
how to use either of them. The corresponding buttons
can be used in the same manner.
i
b
a
c
d
e
f
g
h
j
k
l
n
o
p
q
r
s
m
Part names (remote control)
a
STANDBY/ON button
Press this button to turn the unit on or put it in standby mode.
b
CD/USB button
Use this button to select CD or USB mode.
Use to select playback of the CD or playback of the USB flash drive
or iPod/iPhone connected to the iPod/USB port.
c
Number buttons
Use these buttons to select a track/file number.
For example, to select track/file number 25, press “2” first then “5”.
To select numbers less than 10, press “0” and then the number. As
an example, to select number 5, press “0” then “5”. (Optionally, you
may press just the number “5” and wait for a few seconds.)
d
1/ALL button
Use this button to select the repeat mode. (page 22)
e
A-B button
Use this button to set the points for A-B repeat. (page 22)
f
FOLDER buttons (b/5)
Use these buttons to select a folder of MP3/WMA files. (page 17)
g
SEARCH buttons (m/,)
During playback, use these buttons to search for the part you want
to listen to. (page 18)
h
SHUFFLE button
Use this button for shuffle playback. (page 21)
i
Stop (H) button
Use this button to stop playback and recording.
11
ENGLISH
j
CLEAR button
Use this button to clear a program. (page 21)
k
PROGRAM button
Use this button to enter the program mode. (page 19)
l
MENU button
Use this button to go back to the previous menu of the iPod/
iPhone. This button is the equivalent to the MENU button on your
iPod/iPhone. (page 17)
m
ENTER button
Use this button to select the folder and file. (page 17)
n
DISPLAY button
During MP3/WMA file playback, use this button to change what
information is displayed. (page 23)
o
TIME button
During playback, use this button to change the time display. (page
23)
p
FILE buttons (b/5)
Use these buttons to select an MP3/WMA file. (page 17)
In iPod mode, use this buttons to select a MENU item.
q
SKIP buttons (.//)
Use these buttons to skip tracks/files. (page 18)
r
Play button (G)
Use this button to start playback.
s
Pause button (J)
Use this button to pause playback.
Precautions for use
V
Misuse of batteries could cause them to rupture or leak
leading to fire, injury or the staining of items nearby. Please
carefully read and observe the precautions on page 3.
p Point the remote control unit at the main unit’s remote sensor
from within 5 meters (16 feet) of it. Make sure that there are no
obstructions between the remote control and the main unit.
p If direct sunlight or strong artificial illumination shines on the
remote sensor, the remote control might not function. If that is the
case, move this unit to another location.
p If the remote control unit is operated near other devices that
generate infrared rays, or if other remote control devices using
infrared rays are used near the unit, it might operate incorrectly.
The other devices might also operate incorrectly.
Battery installation
1. Remove the battery compartment cover.
2. Insert two “AA” dry batteries. Make sure that the batteries are
inserted with their positive “+” and negative “_” poles positioned
correctly.
3. Close the cover.
Battery Replacement
If the distance required between the remote control unit and main
unit decreases, the batteries are exhausted. In this case replace the
batteries with new ones.
< For more information about collection of batteries, please contact
your local municipality, your waste disposal service or the point of
sale where you purchased the items.
Remote control unit
12
3
Use the Skip/Search (.m/,/) buttons to turn it
ON/OFF.
Each time you press a Skip/Search (.m/,/) button
the setting switches between ON and OFF.
4
Press the Stop (8) button to confirm the setting.
This product is compliant with the European ErP Standby Power
Regulation.
Under any of the following conditions, the unit will switch to standby
mode if no operation has occurred for 30 minutes or more.
Status CD USB flash drive iPod/iPhone
No disc or connection
Stopped/paused
-
Recording paused -
Automatic power saving function active
- Automatic power saving function not active
/ Not applicable
Changing the automatic power saving (ECO
Mode) setting
1
Put the unit into standby.
2
Press the STANDBY/ON and Stop (8) buttons at the same
time for at least three seconds.
The current ECO Mode setting is shown.
Example:
ECO Mode ON
Current setting
About the ErP
13
ENGLISH
A
How to turn the unit on or put it in standby
Press the STANDBY/ON button to turn the unit on or put it in
standby mode.
ST
ANDBY/ON indicator
The power indicator lights blue when the power is on.
The power indicator lights orange when the unit is in standby.
B
How to select CD or USB
Every time the CD/USB button is pressed, the mode is alternated
between CD and USB.
Select USB to play files on the USB flash drive or iPod/iPhone
connected to the iPod/USB port. (Use the USB cable included with
the iPod/iPhone to connect it to the USB port.)
Basic operation
C
Listening through headphones
When using headphones, first lower the volume before inserting
the headphones plug into the PHONES jack. Then, use the
headphones LEVEL knob to adjust the volume.
< Even when the headphones plug is inserted in the PHONES
jack, sound is output from the analog and digital audio output
connectors.
14
1
Press the CD/USB button to select “CD”.
2
Press the Open/close button (L).
3
Place a disc on the tray with the printed label facing up.
< The disc must be placed centrally into the disc tray. If the disc
is not placed correctly, it may not be possible to open the tray
again once it has closed.
< Never place more than one disc on the tray.
< Do not stick labels or tape on the disc.
< Do not use irregularly shaped discs.
Listening to a CD
4
Press the Open/close button (L) to close the tray.
< Be careful not to pinch your finger.
< It takes a few seconds for the unit to load a disc. No buttons will
work during loading. Wait until the total number of tracks/files
and the total play time of the disc are displayed.
Audio CD
The total number of tracks and total play time of the disc are
displayed.
CD/Stop
T016 72:00
MP3/WMA disc
The total number of files on the disc is displayed.
CD/Stop
Total file 010
15
ENGLISH
5
Press the Play button (y) to start playback.
Disc playback starts from the first track/file.
Audio CD
CD/Play
T003 00:42
current track
number
elapsed time of
the current track
MP3/WMA disc
CD/Play
T003 00:42 MP3
current le number
< MP3/WMA files not contained in folders are automatically put in
the “ROOT” folder, and playback starts from the first file of the
ROOT folder.
< If there are folders that have no MP3/WMA file, the unit skips
them.
< During playback of an MP3/WMA file, “title_artist_album” is
scrolled across the display.
< The unit stops automatically when playback of all the tracks/files
has finished.
< If you load a disc, and then press the Play button (y) (or the
SHUFFLE button on the remote control unit) without having first
closed the disc tray, the disc tray closes and playback starts.
Listening to files on a USB flash drive
You can play MP3/WMA files by connecting USB flash drive.
1
Press the CD/USB button to select “USB”.
“Not connected” will be displayed if no USB flash drive is
connected.
2
Connect an external USB flash drive to the unit.
3
Press the Play button (y).
Playback starts from the first file.
16
1
Press the CD/USB button to select “USB”.
2
Connect your iPod/iPhone using the USB cable supplied
with the iPod/iPhone.
The iPod/iPhone automatically turns on and starts playback from
the iPod/iPhone music list.
< If the display mode is set to “Extended mode” (see page 24),
playback don’t start automatically.
When the iPod/iPhone is connected while CD-H750 is set to another
source, the iPod/iPhone will turn on and enter the pause mode.
< If the source is set to CD when you connect an iPod/iPhone, the
iPod/iPhone turns ON and its playback is paused.
< If an
iPod/iPhone
is connected to this unit, it will only be
recharged when this unit is ON.
< Recharging will stop when the
iPod/iPhone
is fully recharged.
< Recharging is not possible when this unit is in standby.
Listening to an iPod/iPhone Playback (1)
CD
USB
Playing back from selected track/file
1
Press the Skip/search buttons (.m/,/) to select a
track/file, or use the numeric buttons to input the track/file
number.
For example, to select track/file number 25, press “2” first then “5”.
To select numbers less than 10, press “0” and then the number. As
an example, to select number 5, press “0” then “5”. (Optionally, you
may press just the number “5” and wait for a few seconds.)
2
Press the Play button (y) .
Playback starts from the selected track/file.
17
ENGLISH
iPod
Going back to the previous menu
Press the MENU button to go back to the previous menu.
This button is equivalent to the MENU button on your iPod/iPhone.
iPod
Selecting a menu item
1
Use the FILE buttons (¥/˙) to select a menu item.
2
Press the ENTER button.
iPod
Putting the iPod/iPhone in sleep mode (only in
Direct mode)
Hold down the Play button (
y
) for more than 5 seconds.
The iPod/iPhone enters sleep mode.
To cancel sleep mode, press the Play button
(
y
)
again.
CD
USB
Playing back files in a folder
You can select a folder that contains WMA/MP3 files.
1
Use the FOLDER buttons (¥/˙) to select a folder.
2
Press the ENTER button.
3
If you want to select a file, use the FILE buttons (¥/˙).
< Files in the selected folder can be selected.
4
Press the ENTER button.
Playback starts from the selected file.
18
Playback (2)
CD
USB
iPod
Skipping to the next or a previous track/file
During playback, press the Skip/search buttons (.m/
,/) repeatedly until the desired track/file is found.
The selected track/file will be played from the beginning.
On the remote control unit use the Skip buttons (.//).
In stop or pause mode, press the Skip/search buttons
(.m/,/) repeatedly until the track/file you want to listen
to is found. Press the Play button (y) to start playback of the selected
track/file.
< When the .m button is pressed during playback, the track/
file being played will be played from the beginning. To return
to the beginning of the previous track/file, press the .m
button twice.
< Press .m when the playback time is three seconds or less to
start playback of the previous track.
< During programmed playback, the next or previous track/file in
the program is played.
CD
USB
iPod
Searching for a part of a track/file
During playback, hold down one of the Skip/search buttons
(.m/,/) and release it when the part you want to
listen to is found.
On the remote control unit, use the SEARCH buttons (m/,).
< In USB mode, no sound is emitted while searching.
< The unit stops when the end of the last track/file is reached.
CD
USB
Stopping playback
Press the Stop button (
H
).
To start playback again, press the Play button (y).
Playback starts from the first track/file.
CD
USB
iPod
Pausing playback
Press the Pause button (
J
) during playback.
Playback stops at the current position.
To resume playback, press the Play button (y).
19
ENGLISH
CD
USB
Up to 32 tracks/files can be programmed in the desired order.
1
Press the PROGRAM button while in the stop mode.
When CD is selected
P-00 T000
T016 72:00
When USB is selected
P-00 T0000
Total File 0130
2
Use the SKIP buttons (.//) to select a track/file.
When CD is selected
P-01 T001
T016 72:00
When USB is selected
P-01 T0001
Total File 0130
You can also use the numeric buttons to select a track/file.
When you use the numeric buttons, just input the track/fiie
number.
After input, skip to step
4
Programmed playback (1)
For example, to select track/file number 25, press “2” first then “5”.
To select numbers less than 10, press “0” and then the number. As
an example, to select number 5, press “0” then “5”. (Optionally, you
may press just the number “5” and wait for a few seconds.)
3
Within 10 seconds, press the PROGRAM button.
When CD is selected
P-01 T012
T016 72:00
When USB is selected
P-01 T0012
Total File 0130
< Repeat steps
2
and
3
to program more tracks/files.
<
If you make a mistake, press the CLEAR button.
The last programmed number will be deleted.
<
Up to 32 tracks/files can be programmed. If you attempt to
program more than 32 tracks/files, “P-FULL (Program is full)” is
displayed and no more tracks/files can be programmed.
4
When you have finished programming, press the PLAY
button (y) to start programmed playback.
When playback of all the programmed tracks/files has finished, or
if the Stop button (H) or the STANDBY/ON button is pressed, the
program mode will be cancelled.
<
If the unit is disconnected from the power supply, the programmed
contents will be erased.
20
Programmed playback (2)
CD
USB
Checking the programmed order
In stop mode, press the PROGRAM button repeatedly. The track/file
number and program number will be shown on the display.
CD
USB
Changing or adding a track/file to the program
1
In stop mode, press the PROGRAM button repeatedly until
the program number for which you want to change the
track/file appears on the display.
2
Select a track/file using the SKIP buttons (.//).
The previous track/file is replaced with the newly selected one.
If you want to add a track/file to the end of the program, press the
PROGRAM button repeatedly until “P-END" briefly appears on the
display. Then select a track/file using the SKIP buttons (.//).
The track/file is added to the program.
You can also use the numeric buttons.
3
Press the PROGRAM button.
The program is overwritten.
CD
USB
Deleting a track/file from the program
1
In the stop mode, press the PROGRAM button repeatedly
until the program number of the track to be deleted
appears on the display.
2
Press the CLEAR button.
The selected track/file is deleted from the program.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
TEAC CD-H750 Le manuel du propriétaire
- Catégorie
- Lecteur CD
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: TEAC CD-H750 Owner's manual
Documents connexes
-
TEAC CD-RW890CD-RW890MKII Le manuel du propriétaire
-
TEAC CD-RW880 Manuel utilisateur
-
TEAC CD-H750 Manuel utilisateur
-
TEAC CD-RW890MK2-B Manuel utilisateur
-
-
-
-
-
TEAC CD-P1260 Le manuel du propriétaire
-
