Whirlpool AKR 902 IX Program Chart
- Catégorie
- Hottes
- Taper
- Program Chart
AKR 902
5019 100 75085/A
INSTALLATIONSANGABEN
Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl-,
Kohlekochplatten)
INSTALLATION SHEET
Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil
or coal cookers)
FICHE D'INSTALLATION
Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique),
75 cm (cuisinière à gaz, mazout ou charbon)
INSTALLATIESCHEMA
Min. afstand van het kooktoestel: 65 cm (elektrische kooktoestellen),
75 cm (kooktoestellen op gas, olie of kolen)
FICHA DE INSTALACIÓN
Distancia mínima desde los quemadores: 65 cm (quemadores eléctricos),
75 cm (quemadores a gas, gasóleo o carbón)
FICHA DE INSTALAÇÃO
Distância mínima do fogão: 65 cm. (fogões eléctricos), 75 cm. (fogões a gás,
óleo ou carbono)
SCHEDA INSTALLAZIONE
Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas,
gasolio o carbone)
ù(ù ü+ù$ùþ
ü$12.)12.1.)2"0120" FP02!"0120" FP0120"
.0! #02!0. #0! #.
D
GB
F
NL
E
P
I
*5
5019 100 75085/A
AKR 902
16
17
18
F
Vorderseite-Rückseite
Front-rear side
Côté avant-arrière
Voorkant-achterkant
Lado anterior-posterior
Lado dianteiro-traseiro
Lato anteriore-posteriore
ü!)"1&0#!
5019 100 75085/A
AKR 902
1
5
4
3
a
2
3
2
Fig. 1
1.
Control panel.
2.
Grease filters (supplied ready for installation).
3.
Grease filter handles.
4.
Lighting unit.
5.
Telescopic flue.
REPLACING BULBS - Fig. 1
1.
Unplug the appliance or switch off the mains
power supply.
2.
Remove screw (
a
) and detach the lighting unit.
3.
Remove the burnt-out bulb. Use only PL max
9W bulbs.
4.
Remount the lighting unit and secure with
screw (
a
).
WASHING THE GREASE FILTER
Wash the grease filter once a month, or whenever
the grease filter saturation indicator flashes
(Extraction speed indicator
2
).
1.
Unplug the appliance or switch off the mains
power supply.
2.
Removing the grease filters.
- pull the grease filter handles downwards and
disengage from the rear slot (
b, c - Fig. 2
).
3.
After cleaning the grease filters refit in reverse
order, making sure the entire extraction
surface is covered.
FITTING OR RENEWING THE CARBON
FILTER
1.
Unplug the appliance or switch off the mains
power supply.
2.
Remove the grease filters.
3.
Fit the carbon filter, fixing it with the two screws
supplied (
d - Fig. 3
).
4.
If the filter needs renewing, remove the old filter
and fit a new one.
Renew the carbon filter once a year and also
whenever the carbon filter saturation indicator
flashes (Extractor speed indicator
3
).
5.
Remount the grease filters.
CONTROL PANEL
1.
Extraction OFF indicator.
2.
Extractor speed increase ON indicator -
1
Ö
2
Ö
3
Ö
1...
3.
Extraction speed indicator
1
.
4.
Extraction speed indicator
2
and grease filter
saturation indicator (when flashing).
Reset grease filter saturation indicator:
press the extraction OFF button and the light OFF
button simultaneously until the beeper sounds.
The grease filter saturation indicator will stop
flashing.
5.
Extraction speed indicator
3
and carbon filter
saturation indicator (when flashing).
Reset carbon filter saturation indicator:
pressing the extraction OFF and ON buttons
simultaneously until the beeper sounds.
The carbon filter saturation indicator will stop
flashing.
6.
Intensive extraction speed.
7.
Timer
intensive
speed button: the hood
operates at this speed for 5 minutes and then
returns to the previous settings.
This function can be cancelled by pressing
button
1
or
2
.
8.
Light OFF button.
9.
Light ON button.
1234567 89
b
c
d
d
Fig. 3
Fig. 2
PRODUCT DESCRIPTION SHEET
F NL E PGBD GRI
-
1
-
2
-
3
Whirlpool AKR 902 IX Program Chart
- Catégorie
- Hottes
- Taper
- Program Chart
dans d''autres langues
- English: Whirlpool AKR 902 IX