Pioneer MVH-270DAB Manuel utilisateur

English Français Italiano Español Deutsch Nederlands

DIGITAL MEDIA RECEIVER

AUTORADIO NUMÉRIQUE DE MÉDIA

RICEVITORE MULTIMEDIALE DIGITALE

RECEPTOR DIGITAL DE MEDIOS

DIGITALER MEDIA RECEIVER

DIGITAL MEDIA RECEIVER

MVH-270DAB

Operation Manual

Mode d’emploi

Manuale d’istruzioni

Manual de instrucciones

Bedienungsanleitung

Handleiding

2En

Before You Start....................................................................................... 3

Getting Started........................................................................................ 3

Digital Audio Broadcasting (DAB)........................................................ 5

Radio.......................................................................................................... 6

USB/iPod/AUX.......................................................................................... 7

App Mode................................................................................................. 8

Settings ..................................................................................................... 9

FUNCTION settings ................................................................................. 9

AUDIO settings...................................................................................... 10

SYSTEM settings ................................................................................... 10

ILLUMINATION settings....................................................................... 11

Connections/Installation..................................................................... 12

Additional Information........................................................................ 14

Table of Contents

About this manual:

• In the following instructions, a USB memory or USB audio player are referred to as

“USB device”.

• In this manual, iPod and iPhone are referred to as “iPod”.

3En

English

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is especially

important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the

manual in a safe and accessible place for future reference.

Private households in the member states of the EU, in Switzerland and Norway may return their used

electronic products free of charge to designated collection facilities or to a retailer (if you purchase a

similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of

disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery

and recycling and thus prevent potential negative effects on the environment and human health.

WARNING

•Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without training and experience in electronic equipment and automotive

accessories may be dangerous and could expose you to the risk of electric shock, injury or other

hazards.

•Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle

in a safe location before attempting to use the controls on the device.

CAUTION

•Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result.

Also, damage to this unit, smoke, and overheating could result from contact with liquids.

•Always keep the volume low enough to hear outside sounds.

•The Pioneer CarStereo-Pass is for use only in Germany.

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service

Station.

MVH-270DAB

* This button is referred to as DISP in this manual.

Frequently used operations

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal,

the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the

source off.

Before You Start

If you want to dispose this product, do not mix it with general household waste. There is a separate

collection system for used electronic products in accordance with legislation that requires proper

treatment, recovery and recycling.

Getting Started

Basic operation

Purpose Operation

Turn on the power* Press SRC/OFF to turn on the power.

Press and hold SRC/OFF to turn off the

power.

Adjust the volume Turn the M.C. dial.

Select a source Press SRC/OFF repeatedly.

Change the display information Press DISP repeatedly.

Return to the previous display/list Press /DIMMER.

Return to the normal display from the

menu.

Press BAND/.

SRC (source)/OFF

Detach button

Display window

M.C. (multi-control) dial

BAND/

/DIMMER Display button*

4En

Display indication

Detach the front panel to prevent theft. Remove any cables and devices attached to the

front panel and turn off the unit before detaching it.

Important

• Avoid subjecting the front panel to excessive shock.

• Keep the front panel out of direct sunlight and high temperatures.

• Always store the detached front panel in a protective case or bag.

When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the

display.

1 Press the M.C. dial.

The setup menu disappears after 30 seconds of no operation. If you prefer not to set

at this time, turn the M.C. dial to select [NO], then press to confirm.

2 Turn the M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

3 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.C. dial to select [QUIT :NO],

then press to confirm.

4 Press the M.C. dial to confirm the settings.

When [DAB ANT PW] is set to [ON], [UPDATING LIST] appears in the display and the

service list will be updated.

NOTES

• You can cancel the menu setting by pressing SRC/OFF.

• These settings can be made at any time from the SYSTEM settings (page 10) and INITIAL settings

(page 5).

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when the button is pressed.

Appears when the local seek tuning function is set (page 9).

Appears when a traffic program is received.

Appears when traffic announcements are received (page 9).

Appears when the sound retriever function is set (page 9).

Appears when random/shuffle play is set.

Appears when repeat play is set.

Appears when the iPod control function is set (page 8).

Detaching the front panel

Detach Attach

Setup menu

Menu Item Description

LANGUAGE Select the language to display the text information from a

compressed audio file.

[ENG](English),

[РУС](Russian),

[TUR](Turkish)

CLOCK SET Set the clock.

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

DAB ANT PW Supply power to a DAB antenna. Select this when using the

optional DAB antenna (AN-DAB1, sold separately) with the unit.

[ON]

[OFF] No power is supplied to a DAB antenna. Select this when using a

passive antenna with no booster.

5En

English

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [SYSTEM], then press to confirm.

3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.

4 Turn the M.C. dial to select [YES], then press to confirm.

1 Press and hold SRC/OFF until the unit turns off.

2 Press and hold SRC/OFF to display the main menu.

3 Turn the M.C. dial to select [INITIAL], then press to confirm.

4 Turn the M.C. dial to select an option, then press to confirm.

To receive DAB signals, connect a DAB antenna (AN-DAB1) (sold separately) to the unit.

1 Press SRC/OFF to select [DIGITAL RADIO].

2 Press BAND/ to select the band from [D1], [D2] or [D3].

3 Press / to select a service component.

NOTE

Press and hold / then release to seek an available service. Scanning stops when the unit

receives a service.

To select service component from service lists

1

During DAB reception, press .

2 Turn the M.C. dial to select the list type, then press to confirm.

[SERVICE]: Displays the list of all service components. Press again to search for a

service component alphabetically.

[PROGRAM TYPE]: Displays the program type information ([NEWS/INFO],

[POPULAR], [CLASSICS] and [OTHERS]).

[ENSEMBLE]: Displays the list of relevant ensembles.

3 Select a service component from the list you selected, then press the M.C. dial to

confirm.

NOTE

You can update the service list by pressing and holding . To cancel updating, press again.

To store service components

1

While receiving the service component you want to store, press and hold one of

the number buttons (1/ to 6/ ) until it stops flashing.

To receive stored service components

1

Select the band, then press a number button (1/ to 6/).

Canceling the demonstration display (DEMO OFF)

INITIAL settings

Menu Item Description

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

SP-P/O MODE Select when there is a full-range speaker connected to the rear

speaker output leads and there is a subwoofer connected to the

RCA output.

[REAR/SUB.W]

[SUB.W/SUB.W] Select when there is a passive subwoofer connected directly to

the rear speaker output leads and there is a subwoofer

connected to the RCA output.

[REAR/REAR] Select when there are full-range speakers connected to the rear

speaker output leads and RCA output. If there is a full-range

speaker connected to the rear speaker output leads, and the

RCA output is not used, you may select either [REAR/SUB.W] or

[REAR/REAR].

DAB ANT PW Supply power to a DAB antenna. Select this when using the

optional DAB antenna (AN-DAB1, sold separately) with the unit.

[ON]

[OFF] No power is supplied to a DAB antenna. Select this when using a

passive antenna with no booster.

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

restarted automatically. (Some of the settings may be retained

even after resetting the unit.)

[YES], [CANCEL]

Digital Audio Broadcasting (DAB)

Seeking a service component

Presetting service component

6En

The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the

Middle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS

(radio data system) function only works in areas that broadcast RDS signals for FM

stations.

1 Press SRC/OFF to select [RADIO].

2 Press BAND/ to select the band from [FM1], [FM2], [FM3], [MW] or [LW].

3 Press a number button (1/ to 6/).

TIP

The / buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the

FUNCTION settings (page 9).

The six strongest stations are stored on the number buttons (1/ to 6/).

1 After selecting the band, press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [FUNCTION], then press to confirm.

3 Turn the M.C. dial to select [BSM], then press to confirm.

To seek a station manually

1

After selecting the band, press / to select a station.

Press and hold / then release to seek an available station. Scanning stops

when the unit receives a station. To cancel seek tuning, press / .

NOTE

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 9).

To store stations manually

1

While receiving the station you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

The unit searches for a station by PTY (program type) information.

1 Press during FM reception.

2 Turn the M.C. dial to select a program type from [NEWS/INFO], [POPULAR],

[CLASSICS] or [OTHERS].

3 Press the M.C. dial.

The unit begins to search for a station. When it is found, its program service name is

displayed.

NOTES

• To cancel the search, press the M.C. dial.

• The program of some stations may differ from that indicated by the transmitted PTY.

• If no station is broadcasting the type of program you searched for, [NOT FOUND] is displayed for

about two seconds and then the tuner returns to the original station.

PTY list

For more details about PTY list, visit the following site:

http://www.pioneer.eu/eur/products/25/121/tech/CarAudio/PTY.html

Radio

Receiving preset stations

Best stations memory (BSM)

Using PTY functions

7En

English

Disconnect headphones from the device before connecting it to the unit.

USB device/iPod

1

Open the USB port cover.

2 Plug in the USB device/iPod using an appropriate cable.

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB storage device as any device

connected directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

MTP connection

A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable

supplied with the device. However, depending on the connected device and the numbers of the files in

the device, audio files/songs may not be able to be played back via MTP. Note that MTP connection is

not compatible with WAV file formats, and cannot be used with the MIXTRAX function.

AUX

1

Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX] as the source.

NOTE

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source.

You can make various adjustments in the FUNCTION settings (page 9).

Note that the following operations do not work for an AUX device. To operate an AUX

device, use the device itself.

USB/iPod/AUX

Playing back

AUX input jack (3.5 mm stereo jack)

USB port

SRC (source)/OFF

M.C. (multi-control) dial

Operations

Purpose Operation

Select a folder/album* Press 1/ or 2/.

Select a track/song (chapter) Press or .

Fast forward or reverse Press and hold or .

Search for a file from a list 1 Press to display the list.

2 Turn the M.C. dial to select the desired

file (folder) name or category, then press

to confirm.

3 Turn the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

View a list of the files in the selected folder/

category*

Press the M.C. dial when a folder/category

is selected.

Play a song in the selected folder/category* Press and hold the M.C. dial when a folder/

category is selected.

Alphabetical search (iPod only) 1 Press to display the list.

2 Turn the M.C. dial to select the desired

category list, then press to enter the

alphabetical search mode.

(Turning the M.C. dial twice also enters

the alphabetical search mode.)

3 Turn the M.C. dial to select a letter, then

press to display the alphabetical list.

To cancel alphabetical search, press /

DIMMER.

Repeat play Press 6/.

Random/shuffle play Press 5/.

Shuffle all play (iPod only) Press and hold 5/.

Pause/resume playback Press 4/PAU SE.

Return to root folder (USB only)* Press and hold BAND/.

8En

* Compressed audio files only

Link play mode

You can access songs based on the artist, album, or genre currently playing.

1 While listening to a song, press and hold to enter the link play mode.

2 Turn the M.C. dial to select the mode ([ARTIST], [ALBUM], [GENRE]), then press to

confirm.

The selected song/album will be played after the currently playing song.

NOTE

The selected song/album may be canceled if you use functions other than those from the link play

mode (e.g. fast forward and reverse).

iPod control

You can control the unit via a connected iPod.

The following iPod models are not compatible with this function.

– iPod nano 1st generation, iPod with video

1 Press BAND/ during playback, then select the control mode.

[CONTROL iPod/CTRL iPod]: The unit’s iPod function can be operated from the

connected iPod.

[CONTROL AUDIO/CTRL AUDIO]: The unit’s iPod function can only be operated by

the buttons on the unit. In this mode, the connected iPod cannot be turned on or off.

NOTES

• Switching the control mode to [CONTROL iPod/CTRL iPod] pauses song playback. Use the connected

iPod to resume playback.

• The following operations are still accessible from the unit, even if the control mode is set to

[CONTROL iPod/CTRL iPod].

– Pause, fast forward/reverse, song/chapter selection

• The volume can only be adjusted from the unit.

You can enjoy listening to an application on an iPhone via the unit. In some cases, you

can control an application by using the unit.

For details on compatible devices, visit our website.

Important

Use of third party apps may involve or require the provision of personally identifiable information,

whether through the creation of a user account or otherwise, and for certain applications, the provision

of geolocation data.

ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT

LIMITATION COLLECTION AND SECURITY OF USER DATA AND PRIVACY PRACTICES. BY ACCESSING

THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE

PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT

CONSENT TO THE USE OF GEOLOCATION DATA WHERE APPLICABLE, DO NOT USE THAT THIRD PARTY

APP.

For iPhone users

This function is compatible with iPhones and iPod touches installed with iOS 5.0 or later.

NOTE

PIONEER IS NOT LIABLE FOR ANY THIRD PARTY APPS OR CONTENT, INCLUDING WITHOUT LIMITATION

THEIR ACCURACY OR COMPLETENESS. THE CONTENT AND FUNCTIONALITY OF SUCH APPS ARE THE

SOLE RESPONSIBILITY OF THE APP PROVIDER.

1 Connect this unit with the mobile device.

• iPhone via USB (page 7)

2 Press SRC/OFF to select [APP].

3 Operate the mobile device to start up the application.

Basic operations

You can make various adjustments in the FUNCTION settings (page 9).

Change drives in USB device

(Devices that support the USB mass storage

device class protocol only)

Press BAND/.

Useful functions for iPod

Purpose Operation

App Mode

Playback of an application via the unit

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press BAND/.

9En

English

You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select one of the categories below, then press to confirm.

• FUNCTION settings (page 9)

• AUDIO settings (page 10)

• SYSTEM settings (page 10)

• ILLUMINATION settings (page 11)

3 Turn the M.C. dial to select the options, then press to confirm.

The menu items vary according to the source.

Settings

FUNCTION settings

Menu Item Description

S.FOLLOW

[ON], [OFF] Search for another ensemble that supports the

same service component with better reception.

If no alternative service component can be found

or reception remains poor, the unit will

automatically switch to an identical FM

broadcast.

FM SETTING

[TALK], [STANDARD], [MUSIC] Match the sound quality level with the broadcast

signal conditions of the FM band signal.

(Available only when FM band is selected.)

BSM

Store the six strongest stations on the number

buttons (1/ to 6/ ) automatically.

REGIONAL

[ON], [OFF] Limit the reception to the specific regional

programs when AF (alternative frequencies

search) is selected. (Available only when FM

band is selected.)

LOCAL

FM: [OFF], [LV1], [LV2], [LV3], [LV4]

MW/LW: [OFF], [LV1], [LV2]

Restrict the tuning station according to the

signal strength.

TA

[ON], [OFF] Receive current traffic information if available.

(Available only when FM band is selected.)

AF

[ON], [OFF] Allow the unit to retune to a different frequency

providing the same station. (Available only when

FM band is selected.)

NEWS

[ON], [OFF] Interrupt the currently selected source with

news programs. (Available only when FM band is

selected.)

SEEK

[MAN], [PCH] Assign / buttons to seek the stations

one by one (manual tuning) or select a station

from the preset channels.

S.RTRV

[1] (effective for low compression

rates),

[2] (effective for high

compression rates),

[OFF]

Enhance compressed audio and restore rich

sound. (Not available when USB is selected as a

source and the MIXTRAX function is set to on.)

AUDIO BOOK

[FASTER], [NORMAL], [SLOWER] Change the playback speed. (Not available when

[CONTROL iPod/CTRL iPod] is selected in the

control mode.)

PAU SE

Pause or resume playback.

Menu Item Description

USB

iPod

10En

*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*3 Not available when [OFF] is selected in [SUB.W].

You can also access to these menus when the unit is turned off.

AUDIO settings

Menu Item Description

FADER*1

Adjust the front and rear speaker balance.

BALANCE

Adjust the left and right speaker balance.

EQ SETTING

[SUPER BASS], [POWERFUL],

[NATURAL], [VOCAL], [CUSTOM1],

[CUSTOM2], [FLAT]

Select an equalizer band and

level for further customizing.

Equalizer band: [80HZ], [250HZ],

[800HZ], [2.5KHZ], [8KHZ]

Equalizer level: [+6] to [–6]

Select or customize the equalizer curve.

[CUSTOM1] can be set separately for each source.

However, each of the below combinations are set

to the same setting automatically.

• USB, iPod, and APP (iPhone)

[CUSTOM2] is a shared setting used for all

sources.

LOUDNESS

[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.

SUB.W*2

[NOR], [REV], [OFF] Select the subwoofer phase.

SUB.W CTRL*2*3

Cut-off frequency: [50HZ],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Output level: [–24] to [+6]

Slope level: [–12], [–24]

Only frequencies lower than those in the

selected range are output from the subwoofer.

BASS BOOST

[0] to [+6] Select the bass boost level.

HPF SETTING

Cut-off frequency: [OFF], [50HZ],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Slope level: [–12], [–24]

Only frequencies higher than the high-pass filter

(HPF) cutoff are output from the speakers.

SLA

[+4] to [–4] Adjust the volume level for each source except

FM.

Each of the below combinations are set to the

same setting automatically.

• USB, iPod, and APP (iPhone)

SYSTEM settings

Menu Item Description

LANGUAGE

[ENG](English), [РУС](Russian),

[TUR](Turkish)

Select the language to display the text

information from a compressed audio file.

CLOCK SET

Set the clock (page 4).

12H/24H

[12H], [24H] Select the time notation.

AUTO PI

[ON], [OFF] Search for a different station with the same

programming, even if using a preset station.

AUX

[ON], [OFF] Set to [ON] when using an auxiliary device

connected to the unit.

MUTE MODE

[MUTE], [20dB ATT], [10dB ATT] Mute or attenuate sound automatically when a

signal from equipment with a mute function is

received.

PW SAVE*

[ON], [OFF] Reduce the battery power consumption.

Turning on the source is the only operation

allowed when this function is on.

Menu Item Description

11En

English

* [PW SAVE] is canceled if the vehicle battery is disconnected and will need to be turned back on once

the battery is reconnected. When [PW SAVE] is off, depending on connection methods, the unit may

continue to draw power from the battery if your vehicle’s ignition does not have an ACC (accessory)

position.

ILLUMINATION settings

Menu Item Description

DIM SETTING

[SYNC CLOCK], [MANUAL] Change the display brightness.

BRIGHTNESS

[1] to [10] Change the display brightness.

The available setting ranges differ depending on

[DIM SETTING].

12En

Important

• When installing this unit in a vehicle

without an ACC (accessory) position on

the ignition switch, failure to connect the

red cable to the terminal that detects

operation of the ignition key may result

in battery drain.

• Use of this unit in conditions other than

the following could result in fire or

malfunction.

–Vehicles with a 12-volt battery and

negative grounding.

–Speakers with 50 W (output value) and

4 Ω to 8 Ω (impedance value).

• To prevent a short-circuit, overheating or

malfunction, be sure to follow the

directions below.

–Disconnect the negative terminal of the

battery before installation.

–Secure the wiring with cable clamps or

adhesive tape. Wrap adhesive tape

around wiring that comes into contact

with metal parts to protect the wiring.

– Place all cables away from moving parts,

such as the shift lever and seat rails.

–Place all cables away from hot places,

such as near the heater outlet.

–Do not connect the yellow cable to the

battery by passing it through the hole

to the engine compartment.

–Cover any disconnected cable

connectors with insulating tape.

–Do not shorten any cables.

–Never cut the insulation of the power

cable of this unit in order to share the

power with other devices. The current

capacity of the cable is limited.

–Use a fuse of the rating prescribed.

–Never wire the negative speaker cable

directly to ground.

–Never band together negative cables of

multiple speakers.

• When this unit is on, control signals are

sent through the blue/white cable.

Connect this cable to the system remote

control of an external power amp or the

vehicle’s auto-antenna relay control

terminal (max. 300mA 12 V DC). If the

vehicle is equipped with a glass antenna,

connect it to the antenna booster power

supply terminal.

• Never connect the blue/white cable to

the power terminal of an external power

amp. Also, never connect it to the power

terminal of the auto antenna. Doing so

may result in battery drain or a

malfunction.

• The black cable is ground. Ground cables

for this unit and other equipment

(especially, high-current products such as

power amps) must be wired separately. If

they are not, an accidental detachment

may result in a fire or malfunction.

This unit

DAB antenna input

To receive DAB signals, connect a DAB

antenna (AN-DAB1) sold separately to

the unit.

Connections/Installation

Connections

ACC position No ACC position

Power cord input

Rear output or subwoofer output

Front output

Antenna input

Fuse (10 A)

Wired remote input

Hard-wired remote control adapter can

be connected (sold separately).

Power cord

Perform these connections when not

connecting a rear speaker lead to a

subwoofer.

To power cord input

Depending on the kind of vehicle, the

function of and may be different.

In this case, be sure to connect to

and to .

Yel low

Back-up (or accessory)

Yel low

Connect to the constant 12 V supply

terminal.

Red

Accessory (or back-up)

Red

Connect to terminal controlled by the

ignition switch (12 V DC).

Connect leads of the same color to each

other.

Black (chassis ground)

Blue/white

The pin position of the ISO connector

will differ depending on the type of

vehicle. Connect and when Pin 5

is an antenna control type. In another

type of vehicle, never connect and

.

Blue/white

Connect to the system control terminal

of the power amp (max. 300 mA 12 V

DC).

Blue/white

Connect to the auto-antenna relay

control terminal (max. 300 mA 12 V DC).

Yel low /bl ack

If you use equipment with a Mute

function, wire this lead to the Audio

Mute lead on that equipment. If not,

keep the Audio Mute lead free of any

connections.

Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left or subwoofer

Green/black: Rear left or subwoofer

Violet: Rear right or subwoofer

Violet/black: Rear right or subwoofer

ISO connector

In some vehicles, the ISO connector

may be divided into two. In this case, be

sure to connect to both connectors.

NOTES

• Change the initial menu of this unit. Refer

to [SP-P/O MODE] (page 5). The

subwoofer output of this unit is

monaural.

13En

English

• When using a subwoofer of 70 W (2 Ω), be

sure to connect the subwoofer to the

violet and violet/black leads of this unit.

Do not connect anything to the green

and green/black leads.

Power amp (sold separately)

Perform these connections when using the

optional amplifier.

System remote control

Power amp (sold separately)

Connect with RCA cables (sold

separately)

To front output

Front speaker

To rear output or subwoofer output

Rear speaker or subwoofer

Important

• Check all connections and systems before

final installation.

• Do not use unauthorized parts as this

may cause malfunctions.

• Consult your dealer if installation requires

drilling of holes or other modifications to

the vehicle.

• Do not install this unit where:

–it may interfere with operation of the

vehicle.

–it may cause injury to a passenger as a

result of a sudden stop.

• The semiconductor laser will be damaged

if it overheats. Install this unit away from

hot places such as near the heater outlet.

• Optimum performance is

obtained when the unit is

installed at an angle of less

than 60°.

• When installing, to ensure proper heat

dispersal when using this unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

DIN front/rear mount

This unit can be properly installed using

either front-mount or rear-mount

installation.

Use commercially available parts when

installing.

DIN Front-mount

1 Insert the mounting sleeve into the

dashboard.

For installation in shallow spaces, use

the supplied mounting sleeve. If there is

enough space, use the mounting sleeve

that came with the vehicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs

(90°) into place.

Dashboard

Installation

Leave ample

space

5 cm

Mounting sleeve

Make sure that the unit is installed

securely in place. An unstable

installation may cause skipping or other

malfunctions.

DIN Rear-mount

1 Line up the holes on the mounting

bracket with the holes on the sides of

the unit to attach the bracket.

2 Screw in one screw on each side to

hold the unit in place.

Tapping screw (5 mm × 8 mm)

Mounting bracket

Dashboard or console

Removing the unit

1 Remove the trim ring.

Trim ring

Notched tab

• Releasing the front panel allows easier

access to the trim ring.

• When reattaching the trim ring, point

the side with the notched tab down.

2 Insert the supplied extraction keys

into both sides of the unit until they

click into place.

3 Pull the unit out of the dashboard.

14En

The display automatically returns to the

normal display.

→ No operations have been made for

about 30 seconds.

– Perform an operation.

The repeat play range changes

unexpectedly.

→ Depending on the repeat play range,

the selected range may change when

another folder or track is being selected

or during fast forwarding/reversing.

– Select the repeat play range again.

A subfolder is not played back.

→ Subfolders cannot be played when

[FLD] (folder repeat) is selected.

– Select another repeat play range.

The sound is intermittent.

→ You are using a device, such as a cellular

phone, that may cause audible

interference.

– Move electrical devices that may be

causing the interference away from

the unit.

Common

AMP ERROR

→ This unit fails to operate or the speaker

connection is incorrect.

→ The protective circuit is activated.

– Check the speaker connection.

– Turn the ignition switch OFF and back

to ON again. If the message remains,

contact your dealer or an authorized

Pioneer Service Station for assistance.

NO XXXX (NO TITLE, for example)

→ There is no embedded text information.

– Switch the display or play another

track/file.

DAB tuner

ANTENNA ERROR

→ The antenna connection is incorrect.

– Check the antenna connection.

– Turn the ignition switch OFF and back

to ON again. If the message remains,

contact your dealer or an authorized

Pioneer Service Station for assistance.

USB device/iPod

FORMAT READ

→ Sometimes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappears and

you hear sound.

NO AUDIO

→ There are no songs.

– Transfer the audio files to the USB

device and connect.

→ The connected USB device has security

enabled.

– Follow the USB device instructions to

disable the security.

SKIPPED

→ The connected USB device contains

DRM protected files.

– The protected files are skipped.

PROTECT

→ All the files on the connected USB

device are embedded with DRM.

– Replace the USB device.

Additional Information

Troubleshooting

Error messages

N/A USB

→ The connected USB device is not

supported by this unit.

– Disconnect your device and replace it

with a compatible USB device.

CHECK USB

→ The USB connector or USB cable has

short-circuited.

– Check that the USB connector or USB

cable is not caught in something or

damaged.

→ The connected USB device consumes

more than maximum allowable current.

– Disconnect the USB device and do not

use it. Turn the ignition switch OFF

and back to ACC or ON. Connect only

compliant USB devices.

→ The iPod operates correctly but does

not charge.

– Make sure the connection cable for

the iPod has not shorted out (e.g., not

caught in metal objects). After

checking, turn the ignition switch OFF

and back to ON, or disconnect the

iPod and reconnect.

ERROR-19

→ Communication failed.

– Perform one of the following

operations, then return to the USB

source.

• Turn the ignition switch OFF and

back to ON.

• Disconnect the USB device.

• Change to a different source.

→ iPod failure.

– Disconnect the cable from the iPod.

Once the iPod’s main menu is

displayed, reconnect the iPod and

reset it.

ERROR-23

→ USB device was not formatted properly.

– Format the USB device with FAT12,

FAT16 or FAT32.

ERROR-16

→ The iPod firmware version is old.

– Update the iPod version.

→ iPod failure.

– Disconnect the cable from the iPod.

Once the iPod’s main menu is

displayed, reconnect the iPod and

reset it.

STOP

→ There are no songs in the current list.

– Select a list that contains songs.

NOT FOUND

→ No related songs.

– Transfer songs to the iPod.

Apps

START UP APP

→ The application has not started running

yet.

– Operate the mobile device to start up

the application.

USB storage device

• Connections via USB hubs are not

supported.

• Firmly secure the USB storage device

before driving. Do not let the USB storage

device fall onto the floor, where it may

become jammed under the brake or

accelerator pedal.

• Depending on the USB storage device,

the following problems may occur.

–Operations may vary.

–The storage device may not be

recognized.

–Files may not be played back properly.

–The device may cause audible

interference when you are listening to

the radio.

Handling guidelines

15En

English

iPod

• Do not leave the iPod in places with high

temperatures.

• Firmly secure the iPod when driving. Do

not let the iPod fall onto the floor, where

it may become jammed under the brake

or accelerator pedal.

• The settings of the iPod such as the

equalizer and repeat play are changed

automatically when the iPod is

connected to the unit. Once the iPod is

disconnected, those settings will return

to the original settings.

• Incompatible text saved on the iPod will

not be displayed by the unit.

• Only the first 32 characters can be

displayed as a file name (including the file

extension) or a folder name.

• The unit may not work properly

depending on the application used to

encode WMA files.

• There may be a slight delay at the start of

the playback of audio files embedded

with image data, or audio files stored on a

USB device with numerous folder

hierarchies.

CAUTION

• Pioneer cannot guarantee compatibility

with all USB mass storage devices, and

assumes no responsibility for any loss of

data on media players, smartphones, or

other devices while using this product.

• Do not leave discs or a USB storage

device in any place that is subject to high

temperatures.

WMA files

MP3 files

WAV files

• WAV file formats cannot be connected via

MTP.

AAC

Compressed audio

compatibility

File extension .wma

Bit rate 48 kbps to 320 kbps

(CBR), 48 kbps to 384

kbps (VBR)

Sampling frequency 32 kHz, 44.1 kHz, 48

kHz

Windows Media™

Audio Professional,

Lossless, Voice/DRM

Stream/Stream with

video

Not compatible

File extension .mp3

Bit rate 8 kbps to 320 kbps

(CBR), VBR

Sampling frequency 8 kHz to 48 kHz (32

kHz, 44.1 kHz, 48 kHz

for emphasis)

Compatible ID3 tag

version

1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is

given priority over

Version 1.x.)

M3u playlist Not compatible

MP3i (MP3

interactive), mp3 PRO

Not compatible

File extension .wav

Quantization bits 8 and 16 (LPCM), 4

(MSADPCM)

Sampling frequency 16 kHz to 48 kHz

(LPCM), 22.05 kHz and

44.1 kHz (MS ADPCM)

Compatible format AAC encoded by

iTunes

File extension .m4a

Sampling frequency 11.025 kHz to 48 kHz

Transmission rate 16 kbps to 320 kbps,

VBR

USB device

• There may be a slight delay when starting

playback of audio files on a USB storage

device with numerous folder hierarchies.

This unit supports only the following iPod

models. Supported iPod software versions are

shown below. Older versions may not be

supported.

Made for

–iPod touch (1st through 5th generation)

–iPodclassic

–iPod with video

–iPod nano (1st through 7th generation)

–iPhone5s

–iPhone5c

–iPhone5

–iPhone4S

–iPhone4

–iPhone3GS

–iPhone3G

–iPhone

• Operations may vary depending on the

generation and/or software version of

the iPod.

• Users of iPod with the Lightning

Connector should use the Lightning to

USB Cable (supplied with iPod).

• Users of iPod with the Dock Connector

should use the CD-IU51. For details,

consult your dealer.

• Refer to the iPod manuals for information

about the file/format compatibility.

• Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data

lost on the iPod, even if that data is lost

while this unit is used.

The user cannot assign folder numbers and

specify playback sequences with this unit.

Sequence of audio file depends on the

connected device.

Note that the hidden files in a USB device

cannot be played back.

Example of a hierarchy

Apple Lossless Not compatible

AAC file bought from

the iTunes Store (.m4p

file extension)

Not compatible

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy is

less than two tiers.)

Playable folders Up to 500

Playable files Up to 15 000

Playback of copyright-

protected files

Not compatible

Partitioned USB

device

Only the first partition

can be played.

iPod compatibility

Sequence of audio files

Folder

Compressed audio

file

to : Playback sequence

01 to 05: Folder number

16En

iTunes

Apple and iTunes are trademarks of Apple

Inc., registered in the U.S. and other

countries.

WMA

Windows Media is either a registered

trademark or trademark of Microsoft

Corporation in the United States and/or

other countries.

This product includes technology owned

by Microsoft Corporation and cannot be

used or distributed without a license from

Microsoft Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and

iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Lightning is a trademark of Apple Inc.

“Made for iPod” and “Made for iPhone”

mean that an electronic accessory has

been designed to connect specifically to

iPod or iPhone, respectively, and has been

certified by the developer to meet Apple

performance standards. Apple is not

responsible for the operation of this device

or its compliance with safety and

regulatory standards. Please note that the

use of this accessory with iPod or iPhone

may affect wireless performance.

General

Power source: 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system: Negative type

Maximum current consumption: 10.0 A

Dimensions (W × H × D):

DIN

Chassis: 178 mm × 50 mm × 165 mm

Nose: 188 mm × 58 mm × 17 mm

D

Chassis: 178 mm × 50 mm × 165 mm

Nose: 170 mm × 46 mm × 17 mm

Weight: 0.7 kg

Audio

Maximum power output:

50 W × 4

70 W × 1/2 Ω (for subwoofer)

Continuous power output:

22 W × 4 (50 Hz to 15 000 Hz, 5 %

THD, 4 Ω load, both channels driven)

Load impedance: 4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level: 2.0 V

Loudness contour: +10 dB (100 Hz),

+6.5 dB (10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency: 80 Hz/250 Hz/800 Hz/2.5

kHz/8 kHz

Equalization range: ±12 dB (2 dB step)

Subwoofer (mono):

Frequency: 50 Hz/63 Hz/80 Hz/100

Hz/125 Hz/160 Hz/200 Hz

Slope: –12 dB/oct, –24 dB/oct

Gain: +6 dB to –24 dB

Phase: Normal/Reverse

USB

USB standard specification: USB 2.0 full

speed

Maximum current supply: 1 A

USB Class: MSC (Mass Storage Class)

File system: FAT12, FAT16, FAT32

Copyright and trademark Specifications

MP3 decoding format: MPEG-1 & 2 Audio

Layer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11, 12 (2 ch audio) (Windows Media

Player)

AAC decoding format: MPEG-4 AAC (iTunes

encoded only) (Ver. 10.6 and earlier)

WAV signal format: Linear PCM & MS

ADPCM (Non-compressed)

FM tuner

Frequency range: 87.5 MHz to 108.0 MHz

Usable sensitivity: 11 dBf (1.0 μV/75 Ω,

mono, S/N: 30 dB)

Signal-to-noise ratio: 72 dB (IEC-A network)

MW tuner

Frequency range: 531 kHz to 1 602 kHz

Usable sensitivity: 25 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

LW tuner

Frequency range: 153 kHz to 281 kHz

Usable sensitivity: 28 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

DAB tuner

Frequency range (Band III): 174.928 MHz to

239.200 MHz (5 A to 13 F)

Frequency range (L Band): 1 452.960 MHz

to 1 490.624 MHz (LA to LW)

Usable sensitivity (Band III): –100 dBm

Usable sensitivity (L Band): –100 dBm

Signal-to-noise ratio: 85 dB

NOTE

Specifications and the design are subject

to modifications without notice.

17En

English

2Fr

Avant de commencer ............................................................................. 3

Mise en route ........................................................................................... 3

Radiodiffusion numérique (Digital Audio Broadcasting – DAB).... 5

Radio.......................................................................................................... 6

USB/iPod/AUX.......................................................................................... 7

Mode d’application................................................................................. 8

Réglages ................................................................................................... 9

Réglages FUNCTION ............................................................................... 9

Réglages AUDIO.................................................................................... 10

Réglages SYSTEM ................................................................................. 11

Réglages ILLUMINATION..................................................................... 11

Raccordements/Installation................................................................ 12

Informations complémentaires.......................................................... 15

Table des matières

À propos de ce mode d’emploi :

• Parmi les instructions suivantes, les clés USB ou les lecteurs audio USB sont

collectivement désignés sous le nom de « périphérique USB ».

• Dans ce mode d’emploi, les iPod et les iPhone sont collectivement désignés sous le

nom d’« iPod ».

3Fr

Français

Nous vous remercions d’avoir acheté cet appareil PIONEER

Pour garantir une utilisation correcte, lisez bien ce mode d’emploi avant d’utiliser cet appareil. Il est

particulièrement important que vous lisiez et respectiez les indications AVERTISSEMENT et

ATTENTION de ce mode d’emploi. Conservez-le dans un endroit sûr et facilement accessible pour

toute consultation ultérieure.

Dans les états membres de l’UE, en Suisse et en Norvège, les foyers domestiques peuvent rapporter

leurs produits électroniques usagés gratuitement à des points de collecte spécifiés ou à un revendeur

(sous réserve d’achat d’un produit similaire).

Dans les pays qui ne sont pas mentionnés ci-dessus, veuillez contacter les autorités locales pour vous

informer de la méthode correcte de mise au rebut.

En agissant ainsi vous assurerez que le produit que vous mettez au rebut est soumis au processus de

traitement, de récupération et de recyclage nécessaire et éviterez ainsi les effets négatifs potentiels sur

l’environnement et la santé publique.

ATTENTION

•N’essayez pas d’installer cet appareil ou d’en faire l’entretien vous-même. L’installation ou

l’entretien de cet appareil par des personnes sans formation et sans expérience en équipement

électronique et en accessoires automobiles peut être dangereux et vous exposer à des risques

d’électrocution ou à d’autres dangers.

•N’essayez pas de démonter ou de modifier cet appareil. Veillez à quitter la route et garer votre véhicule

en lieu sûr avant d’essayer d’utiliser les commandes de l’appareil.

PRÉCAUTION

•Ne laissez pas cet appareil entrer en contact avec de l’humidité et/ou des liquides. Cela pourrait

provoquer une décharge électrique. Tout contact avec des liquides pourrait également provoquer des

dommages, de la fumée et une surchauffe de l’appareil.

•Maintenez le niveau d’écoute à une valeur telle que vous puissiez entendre les sons provenant de

l’extérieur.

•Le Pioneer CarStereo-Pass est utilisable seulement en Allemagne.

Si vous rencontrez des problèmes

En cas d’anomalie, veuillez contacter votre revendeur ou le centre d’entretien agréé par PIONEER le plus

proche.

MVH-270DAB

* Cette touche est désignée sous le nom de DISP dans ce mode d’emploi.

Opérations fréquemment utilisées

* Si le fil bleu/blanc de l’appareil est relié à la borne de commande du relais d’antenne automatique du

véhicule, l’antenne se déploie lorsque la source de cet appareil est mise en service. Pour rétracter

l’antenne, mettez la source hors service.

Avant de commencer

Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures

ménagères. Il existe un système de collecte séparé pour les appareils électroniques usagés, qui

doivent être récupérés, traités et recyclés conformément à la législation.

Mise en route

Fonctionnement de base

Objectif Opération

Mettre l’appareil sous tension* Appuyez sur SRC/OFF pour mettre

l’appareil sous tension.

Appuyez longuement sur SRC/OFF pour

mettre l’appareil hors tension.

Régler le volume Tournez la molette M.C..

Sélectionner une source Appuyez plusieurs fois sur SRC/OFF.

Modifier les informations d’affichage Appuyez plusieurs fois sur DISP.

Revenir à l’affichage/la liste précédent(e) Appuyez sur /DIMMER.

Revenir à l’affichage normal depuis le

menu.

Appuyez sur BAND/.

SRC (source)/OFF

Touche de retrait

Fenêtre d’affichage

Molette M.C. (multi-contrôle)

BAND/

/DIMMER Touche d’affichage*

4Fr

Indication de l’affichage

Retirez la face avant pour empêcher tout vol. Débranchez tous les câbles et les

périphériques branchés à la face avant et mettez l’appareil hors tension avant de le

retirer.

Important

• Évitez de soumettre la face avant à des chocs excessifs.

• Tenez la face avant à l’abri du soleil et des températures élevées.

• Stockez toujours la face avant détachée, dans un étui de protection ou un sac.

Lorsque vous mettez le contact sur ON après avoir installé l’appareil, [SET UP :YES]

apparaît sur l’affichage.

1 Appuyez sur la molette M.C..

Si vous n’utilisez pas l’appareil dans les 30 secondes qui suivent, le menu de

configuration disparaît. Si vous préférez ne pas effectuer la configuration pour

l’instant, tournez la molette M.C. pour sélectionner [NO], puis appuyez pour valider.

2 Tournez la molette M.C. pour sélectionner les options, puis appuyez pour valider.

Pour passer à l’option de menu suivante, vous devez valider votre sélection.

3 [QUIT :YES] apparaît une fois tous les paramètres réglés.

Pour retourner dans le premier élément du menu de configuration, tournez la

molette M.C. afin de sélectionner [QUIT :NO],

puis appuyez pour valider.

4 Appuyez sur la molette M.C. pour valider les paramètres.

Lorsque [DAB ANT PW] est réglé sur [ON], [UPDATING LIST] apparaît dans l’affichage

et la liste de services est mise à jour.

REMARQUES

• Vous pouvez annuler le réglage du menu en appuyant sur SRC/OFF.

• Ces paramètres peuvent être ajustés à tout moment à partir des réglages SYSTEM (page 11) et des

réglages INITIAL (page 5).

Indication Description

Apparaît lorsqu’il existe un niveau inférieur de menu ou de dossier.

Apparaît lorsque la touche est appuyée.

Apparaît lorsque la fonction d’accord sur une station locale est en service

(page 9).

Apparaît lorsqu’un programme d’informations routières est capté.

Apparaît lorsqu’un bulletin d’informations routières est capté (page 9).

Apparaît lorsque le sound retriever (correcteur de son compressé) est en

service (page 10).

Apparaît lorsque la lecture aléatoire est en service.

Apparaît lorsque la lecture répétée est en service.

Apparaît lorsque la fonction de commande d’iPod est en service (page 8).

Retrait de la face avant

Retirer Fixer

Menu de configuration

Élément de menu Description

LANGUAGE Sélectionnez la langue d’affichage des informations textuelles à

partir d’un fichier audio compressé.

[ENG] (anglais),

[РУС] (russe),

[TUR] (turc)

CLOCK SET Réglez l’horloge.

FM STEP Sélectionnez l’incrément d’accord FM à partir de 100 kHz ou de

50 kHz.

[100], [50]

DAB ANT PW Alimentez une antenne DAB. Sélectionnez cette option lors de

l’utilisation d’une antenne optionnelle DAB (AN-DAB1, vendue

séparément) avec l’appareil.

[ON]

[OFF] Aucune puissance n’est fournie à une antenne DAB. Sélectionnez

cette option lors de l’utilisation d’une antenne passive sans

amplificateur.

La page charge ...

Pioneer MVH-270DAB Manuel utilisateur

Pioneer MVH-270DAB Manuel utilisateur

dans d''autres langues

Documents connexes