Honeywell 0061520 Le manuel du propriétaire

Marque: Honeywell

Modèle: 0061520

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

Owner's Manual

Portable Generator

1-855-GEN-INFO or www.honeywellgenerators.com



DEADLY EXHAUST FUMES! ONLY use OUTSIDE

far away from windows, doors and vents!



NOT INTENDED FOR USE IN CRITICAL LIFE

SUPPORT APPLICATIONS.



SAVE this Manual. Provide this manual to any

operator of the generator.

Introduction ............................................................. 1

Read this Manual Thoroughly ................................. 1

Safety Rules ...........................................................1

Standards Index .............................................................3

General Information ................................................ 4

1.1 Unpacking ......................................................................4

1.2 Assembly .......................................................................4

1.3 Emissions Information ....................................................5

Operation ................................................................ 6

2.1 Know the Generator .......................................................6

2.2 Connection Plugs ...........................................................7

2.3 How to Use the Generator ..............................................8

2.4 Don’t Overload the Generator ..........................................9

2.5 Wattage Reference Guide ...............................................9

2.6 Before Starting the Generator .......................................10

2.7 Starting Pull Start Engines ............................................11

2.8 Starting Electric Start Engines ......................................11

2.9 Stopping the Engine .....................................................12

2.10 Low Oil Level Shutdown System ..................................12

2.11 Charging the Battery (Electric Start Units Only) .............12

Maintenance ......................................................... 12

3.1 Performing Scheduled Maintenance .............................12

3.2 Maintenance Schedule .................................................13

3.3 Product Specifications ..................................................13

3.4 General Recommendations ...........................................13

3.5 Service Air Filter ...........................................................15

3.6 Valve Clearance ............................................................15

3.7 General ........................................................................16

3.8 Long Term Storage .......................................................16

3.9 Other Storage Tips .......................................................16

Troubleshooting .................................................... 17

4.1 Troubleshooting Guide ..................................................17

MANUAL DEL USUARIO .................................... 19

MANUEL DE L'UTILISATEUR ............................. 39

Table of Contents

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

INTRODUCTION

Thank you for purchasing this Honeywell model portable generator

by Generac Power Systems, Inc. This model is a compact, high

performance, air-cooled, engine driven generator designed to

supply electrical power to operate electrical loads where no utility

power is available or in place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Authorized Dealer for starting, operating and servicing

procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using the

equipment. We also strongly recommend instructing other users to

properly start and operate the unit. This prepares them if they need

to operate the equipment in an emergency.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

• Become familiar with and strictly adhere to all local, state and

national codes and regulations.

• Study all safety warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.





This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

Introduction

GENERAL HAZARDS

• NEVER operate in an enclosed area, in a vehicle, or indoors

EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends that the

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

• Operate generator only on level surfaces and where it will not be

exposed to excessive moisture, dirt, dust or corrosive vapors.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving parts. Never remove any fan guard or shield

while the unit is operating.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

• Do NOT operate the generator in the rain.

• Do not alter the construction of the generator or change controls

which might create an unsafe operating condition.

• Never start or stop the unit with electrical loads connected

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

• Do not insert objects through the unit’s cooling slots.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

• On electric start models, disconnect the POSITIVE (+) battery

cable from the engine starter OR the NEGATIVE (-) battery

cable from the battery terminal, whichever is easier, before

transporting the generator.

NOTE:

This generator may be equipped with a spark arrestor muffler.

The spark arrestor must be maintained in effective working

order by the owner/ operator. In the State of California, a spark

arrestor is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands.

EXHAUST & LOCATION HAZARDS

• Never operate in an enclosed area or indoors! NEVER use in

the home, in a vehicle, or in partly enclosed areas such as

garages, EVEN IF doors and windows are open! ONLY use

outdoors and far from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide, which

you cannot see or smell. This poisonous gas, if breathed in

sufficient concentrations, can cause unconsciousness or even

death.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

• This exhaust system must be properly maintained. Do nothing

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

• Always use a battery operated carbon monoxide alarm indoors,

installed according to the manufacturers instructions.

• If you start to feel sick, dizzy, or weak after the generator has

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

• Never handle any kind of electrical cord or device while

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or highly

conductive area (such as metal decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged electrical

cord sets with the generator.

• Before performing any maintenance on the generator, disconnect

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

Safety Rules

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

• Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.

Do not permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

• Never add fuel while unit is running or hot. Allow engine to cool

completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws regulating

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

• Do not insert objects through the unit’s cooling slots.

• Do not operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

• Keep a fire extinguisher near the generator at all times.

STANDARDS INDEX

1. National Fire Protection Association (NFPA) 70: The NATIONAL

ELECTRIC CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association (NFPA) 5000: BUILDING

CONSTRUCTION AND SAFETY CODE available from www.

nfpa.org

3. International Building Code available from www.iccsafe.org

4. Agricultural Wiring Handbook available from www.rerc.org ,

Rural Electricity Resource Council P.O. Box 309 Wilmington,

OH 45177-0309

5. ASAE EP-364.2 Installation and Maintenance of Farm Standby

Electric Power available from www.asabe.org, American

Society of Agricultural & Biological Engineers 2950 Niles

Road, St. Joseph, MI 49085

This list is not all inclusive. Check with the Authority Having Local

Jurisdiction (AHJ) for any local codes or standards which may be

applicable to your jurisdiction.

MODEL NO:

SERIAL NO:

Unit ID Location

Safety Rules

1.1 UNPACKING

• Remove all packaging material.

• Remove separate accessory box.

• Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged, locate an

authorized dealer at 1-855-GEN-INFO.

• 1-Owner’s manual

• 1-Bottle of Oil SAE 30

• 3-Product Registration Cards (English, Spanish, French)

• 1-Oil Funnel

• 4-Carriage Bolts (A)

• 4-Acorn Nuts (B)

• 2-Small Washers (C)

• 2-Rubber Feet (D)

• 2-Foot Brackets (E)

• 2-M8-1.25 x 25.4 (F)

• 8-M8-1.25 x 16 (G)

• 10-M8 Nuts (H)

• 1-Axle (J)

• 1-Axle Bracket (K)

• 2-Wheels (L)

• 2-Large Washers (M)

• 2-Hair Pins (N)

• 1-Battery Charger (Electric start models)

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If

problems arise when assembling the generator, please call the

Generator Helpline at 1-855-GEN-INFO.

1.2.1 ASSEMBLING THE ACCESSORY KIT

The wheels are designed to greatly improve the portability of the

generator. You will need the following tools to properly install the

accessory kit:

• Ratchet, a 10mm socket and a 13mm socket

• 10mm box wrench

Refer to the instructions below and figures 1A, 1B, and 1C to

install the handles, feet, and wheels. Note: the handle components

are already pre-assembled from the factory.

Handle (Figure 1A)

1. Install the handle assembly to the frame by using bolts (A) and

nuts (B).

2. Repeat step one for opposite handle.

Feet (Figure 1B)

3. Place washer (C) inside rubber foot (D). Secure parts to

bracket (E) with bolt (F) and nut (H).

4. Install foot assembly to the frame using the short bolts (G)

and nuts (H).

5. Repeat steps 3 & 4 for other foot.

Wheels (Figure 1C)

6. Use four short bolts (G) and four nuts (H) to secure the axle

(J) & bracket (K) to the frame.

7. Slide wheel (L) and washer (M) onto axle (J). Secure parts

with pin (N).

8. Repeat steps 6 & 7 for the opposite wheel.

Figure 1A – Handle Assembly

Figure 1B – Foot Assembly

General Information

Figure 1C – Wheel Assembly

1.2.2 BATTERY CABLE CONNECTION (ELECTRIC START

ONLY)

The unit has been deliberately shipped with the battery cables

disconnected. You will need two 8mm wrenches to secure the

battery cables.

To connect the battery (see Figure 14 for connection details):

1. Cut off cable ties securing battery cables.

2. First, connect the red cable to the positive (+) battery terminal

with the supplied bolt.

3. Connect the black cable to the negative (-) battery terminal

with the supplied bolt.

4. Make sure all connections are secure. Slide the rubber boots

over the terminals and connection hardware.

NOTE:

If the battery is unable to start the engine, charge it with the

12V charger included in the accessory box (see the "Charging a

Battery" section for details).

1.3 EMISSIONS INFORMATION

The Environmental Protection Agency (and California Air Resource

Board for generators certified to CA standards) requires that

this generator comply with exhaust and evaporative emission

standards. Locate the emissions compliance decal on the engine

to determine what standards the generator meets, and to determine

which warranty applies. This generator is certified to operate on

gasoline. The emission control system includes the following

components (if equipped):

• Air Induction System

– Intake Pipe / Manifold

– Air Cleaner

• Fuel System

– Carburetor

– Fuel Tank / Cap

– Fuel Lines

– Evaporative Vent Lines

– Carbon Canister

• Ignition System

– Spark Plug

– Ignition Module

• Exhaust System

– Exhaust Manifold

– Muffler

– Pulsed Air Valve

– Catalyst

General Information

2.1 KNOW THE GENERATOR

Read the Owner’s Manual and Safety Rules before operating

this generator.

Compare the generator to Figures 2 through 4 to become

familiarized with the locations of various controls and adjustments.

Save this manual for future reference.

1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies

electrical power for the operation of 120 Volt AC, 20 Amp,

single-phase, 60 Hz electrical lighting, appliance, tool and

motor loads (CARB models are equipped with GFCI outlets).

2. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 and/or 240 Volt AC,

30 Amp, single-phase, 60 Hz, electrical lighting, appliance,

tool and motor loads.

3. Circuit Breakers (AC) – Each receptacle is provided with

a circuit breaker to protect the generator against electrical

overload.

4. Oil Drain – Use to drain engine oil.

5. Air Filter – Filters intake air as it is drawn into the engine.

6. Choke Knob – Used when starting a cold engine.

7. Fuel Tank – See generator Specifications for tank capacity.

8. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

9. Run/Stop Switch – Controls the operation of the generator

(pull start models).

9A. Start Switch – Used to start engine from the starter motor

(electric start models only).

10. Muffler – Quiets the engine.

11. Handles – Pivot and retract for storage. Press the spring-

loaded button to move handles.

12. Gas Cap – Fuel fill location.

13. Fuel Gauge – Shows fuel level in tank.

14. Oil Fill – Add oil here.

15. Recoil Starter – Use to start engine manually.

16. Fuel Shut Off – Valve between fuel tank and carburetor.

Figure 2A - Control Panel (49 State CSA Models)

Figure 2B - Control Panel (CARB Models)

17. Battery Charger Input – This receptacle allows the capability

to recharge the 12 volt DC storage battery provided with

the 12 Volt Adaptor Plug Charger which is included in the

Accessory Box. Located behind the battery charger input is

a 1.50 Amp in-line fuse which is inside the control panel to

protect the battery (electric start models only).

18. Battery – Powers the electric starter (electric start models

only).

Figure 3 - Generator Controls

Operation

Figure 4 - Generator Controls

2.2 CONNECTION PLUGS

2.2.1 120 VAC, 20 AMP, DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 20 Amp

push-to-reset circuit breaker (Figure 5). Use each socket to power

120 Volt AC, single phase, 60 Hz electrical loads requiring up to a

combined 2400 watts (2.4 kW) or 20 Amps of current. Use only

high quality, well-insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

Keep extension cords as short as possible, preferably less than

15 feet long, to prevent voltage drop and possible overheating of

wires.

Figure 5 - 120 Volt AC, 20 Amp, Duplex Receptacle

2.2.2 120 VAC, 20 AMP, GFCI DUPLEX RECEPTACLE

(CARB ONLY)

This is a 120 Volt outlet protected against overload by a 20 Amp

push-to-reset circuit breaker (Figure 6). Use each socket to power

120 Volt AC, single phase, 60 Hz electrical loads requiring up to a

combined 2400 watts (2.4 kW) or 20 Amps of current. Use only

high quality, well-insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

Keep extension cords as short as possible to prevent voltage drop

and possible overheating of wires.

Figure 6 - 120 Volt AC, 20 Amp, GFCI Duplex Receptacle

2.2.3 120/240 VAC, 30 AMP RECEPTACLE

Use a NEMA L14-30 plug with this receptacle (rotate to lock/

unlock). Connect a suitable 4-wire grounded cord set to the plug

and to the desired load. The cord set should be rated for 250 Volts

AC at 30 Amps (or greater) (Figure 7).

Figure 7 - 120/240 VAC, 30 Amp Receptacle

Use this receptacle to operate 120 Volt AC, 60 Hz, single phase

loads requiring up to 3600 watts (3.6 kW) of power at 30 Amps or

240 Volt AC, 60 Hz, single phase loads requiring up to 7200 watts

(7.2 kW) of power at 30 Amps. The outlet is protected by a 2-pole

toggle switch circuit breaker.

Operation

2.3 HOW TO USE THE GENERATOR

See the "To Start the Engine" section for how to safely start and

stop the generator and how to connect and disconnect loads. If

there are any problems operating the generator, please call the

generator helpline at 1-888-436-3722.



Never operate in an enclosed area or indoors!

NEVER use in the home, in a vehicle, or in

partly enclosed areas such as garages, EVEN

IF doors and windows are open! ONLY use

outdoors and far from open windows, doors,

vents, and in an area that will not accumulate

deadly exhaust.



The engine exhaust fumes contain carbon

monoxide, which you cannot see or smell.

This poisonous gas, if breathed in sufficient

concentrations, can cause unconsciousness or

even death.



Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or permit

even partial blockage of ventilation provisions,

as this can seriously affect safe operation

of the generator. The generator MUST be

operated outdoors.



This exhaust system must be properly

maintained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.



Always use a battery operated carbon

monoxide alarm indoors, installed according to

the manufacturer's instructions.

2.3.1 GROUNDING THE GENERATOR WHEN USED AS A

PORTABLE

This generator has an equipment ground that connects the

generator frame components to the ground terminals on the AC

output receptacles (see NEC 250.34 (A) for explanation). This

allows the generator to be used as a portable without grounding

the frame of the generator as specified in NEC 250.34.

Special Requirements

There may be Federal or State Occupational Safety and Health

Administration (OSHA) regulations, local codes, or ordinances that

apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or the

local agency having jurisdiction:

• In some areas, generators are required to be registered with

local utility companies.

• If the generator is used at a construction site, there may be

additional regulations which must be observed.

2.3.2 CONNECTING THE GENERATOR TO A BUILDING’S

ELECTRICAL SYSTEM

When connecting directly to a building's electrical system, it is

recommended that a manual transfer switch is used. Connections

for a portable generator to a building's electrical system must be

made by a qualified electrician and in strict compliance with all

national and local electrical codes and laws.

Figure 8 - Grounding the Generator

Grounding

Operation

2.3.3 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles. DO NOT

connect 3-phase loads to the generator. DO NOT connect 50 Hz

loads to the generator.

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 or 240 Volt AC, single

phase, 60 Hz electrical loads.

• Add up the rated watts (or amps) of all loads to be connected

at one time. This total should not be greater than (a) the rated

wattage/amperage capacity of the generator or (b) circuit

breaker rating of the receptacle supplying the power. See "Don't

Overload the Generator".

2.4 DON’T OVERLOAD THE GENERATOR

Overloading a generator in excess of its rated wattage capacity

can result in damage to the generator and to connected electrical

devices. Observe the following to prevent overloading the unit:

• Add up the total wattage of all electrical devices to be connected

at one time. This total should NOT be greater than the

generator's wattage capacity.

• The rated wattage of lights can be taken from light bulbs. The

rated wattage of tools, appliances and motors can usually be

found on a data label or decal affixed to the device.

• If the appliance, tool or motor does not give wattage, multiply

volts times ampere rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction types, require about

three times more watts of power for starting than for running.

This surge of power lasts only a few seconds when starting

such motors. Make sure to allow for high starting wattage when

selecting electrical devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other connected

loads.

The Wattage Reference Guide is provided to assist in determining

how many items the generator can operate at one time.

NOTE:

All figures are approximate. See data label on appliance for

wattage requirements.

2.5 WATTAGE REFERENCE GUIDE

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

Electric Skillet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

*Freezer . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875

*Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 to 750

Hair Dryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 to 1100

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Lawn Mower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Light Bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Microwave Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700 to 1000

*Milk Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . 400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . 600

Paint Sprayer, Airless (handheld). . . . . . . . . . . . . . . . . . . . . . . . . 150

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 to 200

*Refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

Slow Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . 2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Submersible Pump (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1750 to 2000

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 to 500

Toaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 to 1650

Weed Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

* Allow 3 times the listed watts for starting these devices.

Operation

2.6 BEFORE STARTING THE GENERATOR

Prior to operating the generator, engine oil and gasoline will need

to be added, as follows:

2.6.1 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Use no special additives. Select

the oil's viscosity grade according to the expected operating

temperature (also see chart).

• Above 40° F, use SAE 30

• Below 40° F and down to 10° F, use 10W-30

• Below 10° F, use synthetic 5W-30

10W-30

10W-3 0

SAE 30

SAE 3 0

Synthetic 5W-30

Synthet i c 5 W-30



Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine

failure.

1. Place generator on a level surface (not to exceed 15° in any

direction).

2. Clean area around oil fill and remove oil fill cap.

3. Slowly fill engine with oil. Stop filling occasionally to check oil

level. Oil level is full when level is up to the threads of the oil

fill plug.

4. Install oil fill plug and finger tighten securely.

5. Check engine oil level before starting each time thereafter.

2.6.2 ADDING GASOLINE



 Never fill fuel tank indoors. Avoid spilling

gasoline on hot engine. Allow engine to cool

entirely before adding fuel. Never fill fuel tank

when engine is running or hot. DO NOT light

a cigarette or smoke when filling the fuel tank.

Gasoline is highly flammable and its vapors are

explosive.



 Do not overfill the fuel tank. Always leave room

for fuel expansion. If the fuel tank is overfilled,

fuel can over flow onto a hot engine and cause

fire or an explosion. Wipe up any spilled fuel

immediately.

1. Use regular UNLEADED gasoline with the generator engine. Do

not use premium gasoline. Do not mix oil with gasoline.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add unleaded regular gasoline to fuel tank. Be careful

not to overfill (Figure 9).

4. Install fuel cap and wipe up any spilled gasoline.

IMPORTANT: It is important to prevent gum deposits from forming

in fuel system parts such as the carburetor, fuel hose or tank

during storage. Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or

longer. See the "Storage" section. Never use engine or carburetor

cleaner products in the fuel tank as permanent damage may occur.

Figure 9 - Fuel Tank

DO NOT Fill Above Lip

Fuel

Fuel Tank

Operation

2.7 STARTING PULL START ENGINES



Never start or stop engine with electrical

devices plugged into the receptacles AND

devices turned on.

1. Unplug all electrical loads from the unit's receptacles before

starting the engine.

2. Make sure the unit is in a level position (not to exceed 15° in

any direction).

3. OPEN the Fuel Shut-off Valve (Figure 10).

4. Turn engine RUN/STOP switch to ON position (Figure 2A).

5. Slide engine choke to the LEFT to FULL CHOKE position

(Figure 11).

6. To start engine, firmly grasp the recoil handle and pull slowly

until increased resistance is felt. Pull rapidly up and away.

7. When engine starts, move choke knob to 1/2-CHOKE position

until engine runs smoothly and then fully into RUN position.

If engine falters, move choke back out to 1/2-CHOKE position

until engine runs smoothly and then to RUN position.

NOTE:

If engine fires, but does not continue to run, move choke lever

to FULL CHOKE and repeat starting instructions.

Figure 10 - Fuel Shut-off Valve

Figure 11 - Choke Position

CHOKE LEVER

LEFT = CHOKE (START)

RIGHT = RUN

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with push-to-reset-type circuit breakers. If amperage

rating of any circuit breaker is exceeded, that breaker opens and

electrical output to that receptacle is lost. Read “Don’t Overload the

Generator” carefully.

2.8 STARTING ELECTRIC START ENGINES



Never start or stop engine with electrical

devices plugged into the receptacles AND

devices turned on.

1. Unplug all electrical loads from the unit's receptacles before

starting the engine.

2. Make sure the unit is in a level position (not to exceed 15° in

any direction).

3. Open the fuel shut-off valve (Figures 10).

4. Move engine CHOKE knob outward to FULL CHOKE position

(Figure 11).

5. To start engine, press and hold the Start/Run/Stop switch in

the “Start” position. The engine will crank and attempt to start.

When the engine starts, release the switch to the run position.

6. When the engine starts, move choke knob to “1/2 Choke”

position until the engine runs smoothly and then fully in to the

“Run” position. If engine falters, move choke knob back out to

“1/2 Choke” position until the engine runs smoothly and then

to “Run” position.

2.8.1 MANUAL START

This generator is also equipped with a manual recoil starter which

may be used if the battery is discharged.

NOTE:

The switch must be in the RUN position. Use one of the

generator’s receptacle outlets along with the included battery

charger to charge the battery while the generator is running.

• To start manually, firmly grasp the recoil handle and pull slowly

until increased resistance is felt. Pull rapidly up and away to

start engine. Then follow the same choke sequence.

NOTE:

If engine fires, but does not continue to run, move choke lever

to FULL CHOKE and repeat starting instructions.

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with push-to-reset-type circuit breakers. If amperage

rating of any circuit breaker is exceeded, that breaker opens and

electrical output to that receptacle is lost. Read “Don’t Overload the

Generator” carefully.

Maintenance

2.9 STOPPING THE ENGINE

1. Shut off all loads, then unplug the electrical loads from

generator panel receptacles. Never start or stop the engine

with electrical devices plugged in and turned on.

2. Let engine run at no-load for several minutes to stabilize the

internal temperatures of engine and generator.

3. Move Run/Stop switch to OFF position.

4. Close fuel valve.

2.10 LOW OIL LEVEL SHUTDOWN SYSTEM

The engine is equipped with a low oil level sensor that shuts down

the engine automatically when the oil level drops below a specified

level. If the engine shuts down by itself and the fuel tank has

enough gasoline, check engine oil level.

2.10.1 SENSING LOW OIL LEVEL

If the system senses a low oil level during operation, the engine

shuts down. The engine will not run until the oil has been refilled

to the proper level.

2.11 CHARGING THE BATTERY (ELECTRIC START

UNITS ONLY)



 Storage batteries give off explosive hydrogen

gas while recharging. An explosive mixture will

remain around the battery for a long time after

it has been charged. The slightest spark can

ignite the hydrogen and cause an explosion.

Such an explosion can shatter the battery and

cause blindness or other serious injury.





Do not permit smoking, open flame, sparks

or any other source of heat around a battery.

Wear protective goggles, rubber apron and

rubber gloves when working around a battery.

Battery electrolyte fluid is an extremely

corrosive sulfuric acid solution that can cause

severe burns. If spill occurs flush area with

clear water immediately.

NOTE:

The battery shipped with the generator has been fully charged.

A battery may lose some of its charge when not in use for

prolonged periods of time. If the battery is unable to crank the

engine, plug in the 12V charger included in the accessory box

(see section "Charging the Battery"). RUNNING THE GENERATOR

DOES NOT CHARGE THE BATTERY.

Use battery charger plug to keep the battery charged and ready for

use. Battery charging should be done in a dry location.

1. Plug charger into “Battery Charger Input” jack, located on the

control panel. Plug wall receptacle end of the battery charger

into a 120 Volt AC wall outlet (Figure 12).

2. Unplug battery charger from wall outlet and control panel jack

when generator is going to be in use.

NOTE:

Do not use the battery charger for more than 48 hours at one

charge.

Figure 12 - Battery Charger Jack

BATTERY

CHARGER

INPUT

3.1 PERFORMING SCHEDULED MAINTENANCE

It is important to perform service as specified in the Maintenance

Schedule for proper generator operation, and to ensure that the

generator complies with the applicable emission standards for the

duration of its useful life. Service and repairs may be performed by

any capable person or repair shop. Additionally, emissions critical

maintenance must be performed as scheduled in order for the

Emissions Warranty to be valid. Emissions critical maintenance

consists of servicing the air filter and spark plugs in accordance

with the Maintenance Schedule.

Maintenance

3.2 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required

when operating in adverse conditions noted below.

Check Oil Level At Each Use

Change Oil ‡ *Every 100 hours or Every Season

Check Valve Clearance ***Every Season

Service Air Filter ** Every 200 hours or Every Season

Replace Spark Plug Every Season

‡ Change oil after first 30 hours of operation then every season.

* Change oil and oil filter every month when operating under heavy load or in high

temperatures.

** Clean more often under dirty or dusty operating conditions. Replace air filter

parts if they cannot be adequately cleaned.

*** Check valve clearance and adjust if necessary after first 50 hours of

operation and every 100 hours thereafter.

3.3 PRODUCT SPECIFICATIONS

3.3.1 GENERATOR SPECIFICATIONS

5.5 kW

Rated Power ........................................................................5.5 kW*/**

Surge Power ...........................................................................6.8 kW**

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V ........................................................... 22.9 Amps**

Current @120V ............................................................ 45.8 Amps**

Rated Frequency ..................................................... 60 Hz @3600 RPM

Phase ................................................................................Single Phase

6.5 kW

Rated Power ........................................................................6.5 kW*/**

Surge Power ...........................................................................8.1 kW**

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V ............................................................27.1 Amps**

Current @120V ............................................................ 54.2 Amps**

Rated Frequency ..................................................... 60 Hz @3600 RPM

Phase ................................................................................Single Phase

7.5 kW

Rated Power ........................................................................7.5 kW*/**

Surge Power .......................................................................... 9.4 kW**

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V ............................................................31.3 Amps**

Current @120V ............................................................ 62.5 Amps**

Rated Frequency ..................................................... 60 Hz @3600 RPM

Phase ................................................................................Single Phase

* Operating temperature range: 0 °F (-18 °C) to 110 °F (43 °C). When operating

above 77 °F (25 °C) there may be a decrease in power.

** Maximum wattage and current are subject to, and limited by, such factors

as fuel Btu content, ambient temperature, altitude, engine condition, etc..

Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each 6° C (10° F) above 16° C (60° F)

ambient temperature.

3.3.2 ENGINE SPECIFICATIONS

5.5 & 6.5 kW

Displacement ...............................................................................389cc

Spark Plug Type ................................ NHSP LDF7TC or Champion N9YC

Spark Plug Gap ............................. 0.028-0.031 inches (0.70-0.80 mm)

Spark Plug Part Number ..................................................... 0J00620106

Gasoline Capacity .........................................................5.8 U.S. Gallons

Oil Type....................................See Chart in “Adding Engine Oil” Section

Oil Capacity ....................................................................1 L (1.06 Qts.)

Run Time (50% Load) ...................................................................9 hrs.

7.5 kW

Displacement ...............................................................................420cc

Spark Plug Type ................................ NHSP LDF7TC or Champion N9YC

Spark Plug Gap ....................................................0.030 inch (0.76 mm)

Spark Plug Part Number ..................................................... 0J00620106

Gasoline Capacity .........................................................5.8 U.S. Gallons

Oil Type....................................See Chart in “Adding Engine Oil” Section

Oil Capacity ....................................................................1 L (1.06 Qts.)

Run Time (50% Load) ...................................................................8 hrs.

3.4 GENERAL RECOMMENDATIONS

The warranty of the generator does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly

maintain the generator.

All adjustments in the Maintenance section of this manual should

be made at least once each season. Follow the requirements in the

"Maintenance Schedule".

NOTE:

Once a year replace the spark plug and replace the air filter.

A new spark plug and clean air filter assure proper fuel-air

mixture and help the engine run better and last longer.

3.4.1 GENERATOR MAINTENANCE

Generator maintenance consists of keeping the unit clean and dry.

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors. Cooling air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.



Never insert any object or tool through the air

cooling slots, even if the engine is not running.

NOTE:

DO NOT use a garden hose to clean generator. Water can enter

the engine fuel system and cause problems. In addition, if water

enters the generator through cooling air slots, some water will

be retained in voids and crevices of the rotor and stator winding

insulation. Water and dirt buildup on the generator internal

windings will eventually decrease the insulation resistance of

these windings.

3.4.2 TO CLEAN THE GENERATOR

• Use a damp cloth to wipe exterior surfaces clean.

• A soft, bristle brush may be used to loosen caked on dirt,

oil, etc.

• A vacuum cleaner may be used to pick up loose dirt and debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and openings

on the generator. These openings must be kept clean and

unobstructed.

3.4.3 ENGINE MAINTENANCE



When working on the generator, always

disconnect negative cable from battery. Also

disconnect spark plug wire from spark plug and

keep wire away from spark plug.

3.4.4 CHECKING OIL LEVEL

See the “Before Starting the Generator” section for information on

checking the oil level. The oil level should be checked before each

use, or at least every eight hours of operation. Keep the oil level

maintained.

3.4.5 CHANGING THE OIL

Change the oil after the first 30 hours of operation. Change the

oil every 100 hours or every season thereafter. If running this

unit under dirty or dusty conditions, or in extremely hot weather,

change the oil more often.



Hot oil may cause burns. Allow engine to

cool before draining oil. Avoid prolonged

or repeated skin exposure with used oil.

Thoroughly wash exposed areas with soap.

Use the following instructions to change the oil after the engine

cools down:

1. Clean area around oil drain plug.

2. Remove oil drain plug from engine and oil fill plug to drain oil

completely into a suitable container.

3. When oil has completely drained, install oil drain plug and

tighten securely.

4. Fill engine with recommended oil. (See “Before Starting the

Generator” for oil recommendations).

5. Wipe up any spilled oil.

6. Dispose of used oil at a proper collection center.

3.4.6 REPLACING THE SPARK PLUG

See Engine Specifications for recommended spark plug. Replace

the plug once each year. This will help the engine start easier and

run better.

1. Stop the engine and pull the spark plug wire off of the spark

plug.

2. Clean the area around the spark plug and remove it from the

cylinder head.

3. Set the spark plug's gap to 0.70-0.80 mm (0.028-0.031 in.).

Install the correctly gapped spark plug into the cylinder head

(Figure 13).

Figure 13 - Spark Plug Gap

3.4.7 BATTERY REPLACEMENT

NOTE:

The battery shipped with the generator has been fully charged.

A battery may lose some of its charge when not in use for

prolonged periods of time. If the battery is unable to crank

the engine, plug in the 12V charger included in the accessory

box (see the Charging a Battery section). RUNNING THE

GENERATOR DOES NOT CHARGE THE BATTERY. Refer to the

Battery Cable Connection section.

Figure 14 - Battery Connections

Maintenance

3.5 SERVICE AIR FILTER

The engine will not run properly and may be damaged if using a

dirty air filter. Clean or replace the air filter paper filter once a year.

Clean or replace more often if operating under dusty conditions

(Figure 15).

To clean or replace paper air filter:

1. Remove air filter cover and remove paper filter.

2. Clean paper filter by tapping it gently on a solid surface. If the

filter is too dirty, replace it with a new one. Dispose of the old

filter properly. The air filter part number is 0G84420151.

3. Clean air filter cover, then insert new paper filter into the base

of the air filter. Re-install air filter cover.

NOTE:

To order a new air filter, please contact the nearest authorized

service center at 1-855-GEN-INFO.

Figure 15 - Air Filter

KNOB TO

OPEN AIR BOX

3.5.1 CLEAN SPARK ARRESTOR SCREEN (CARB

MODELS)

The engine exhaust muffler has a spark arrestor screen. Inspect

and clean the screen at least once each year (Figure 16). If unit is

used regularly, inspect and clean more often.



If using the generator on any forest-covered,

brush-covered or grass-covered unimproved

land, it must be equipped with a spark arrestor.

The spark arrestor must be maintained in good

condition by the owner/operator.

Clean and inspect the spark arrestor when the engine is at ambient

temperature as follows:

1. Remove the spark arrestor screen from the muffler by

loosening the clamp and removing the screw.

2. Inspect screen and replace if torn, perforated or otherwise

damaged. DO NOT USE a defective screen. If screen is not

damaged, clean it with commercial solvent.

3. Replace the spark arrestor and secure with the clamp and

screw.

NOTE:

To order a new air filter or spark arrestor screen, please contact

the nearest authorized service center at 1-800-333-1322.

Figure 16 – Spark Arrestor Screen

3.6 VALVE CLEARANCE

• Intake — 0.15 ± 0.02mm (cold), (0.006" ± 0.0008" inches)

• Exhaust — 0.20 ± 0.02mm (cold) (0.008" ± 0.0008" inches)

After the first 50 hours of operation, check the valve clearance

in the engine and adjust if necessary.

Important: If feeling uncomfortable about doing this procedure or

the proper tools are not available, please take the generator to the

nearest service center to have the valve clearance adjusted. This is

a very important step to ensure longest life for the engine.

Maintenance

3.7 GENERAL

The generator should be started at least once every thirty days and

be allowed to run at least 30 minutes. If this cannot be done and

the unit must be stored for more than 30 days, use the following

information as a guide to prepare it for storage.





NEVER store engine with fuel in tank indoors

or in enclosed, poorly ventilated areas where

fumes may reach an open flame, spark or pilot

light as on a furnace, water heater, clothes

dryer or other gas appliance.



Allow unit to cool entirely before storage.

3.8 LONG TERM STORAGE

It is important to prevent gum deposits from forming in essential

fuel system parts such as the carburetor, fuel hose or tank during

storage. Also, experience indicates that alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract moisture, which

leads to separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied

before storage of 30 days or longer, as follows:

• A quality fuel stabilizer should be added to the existing fuel per

the manufacturers specifications.



 Drain fuel into approved container outdoors,

away from open flame. Be sure engine is cool.

Do not smoke.

• Start and run the engine for 10 - 15 minutes, after that time and

while the unit is running, turn the fuel shut-off valve OFF and run

until the engine stops from lack of fuel.

• Allow the engine to cool, then remove all gasoline from the fuel

tank. Use a commercially available, non-conductive vacuum

siphon. Drain oil from crankcase. Refill the crankcase with

recommended grade oil.

• Remove spark plug and spray with a quality fogging agent, or

pour about 1/2 ounce (15 ml) of engine oil into the cylinder.

Cover spark plug hole with rag. Pull the recoil starter a couple

times to lubricate the piston rings and cylinder bore. A fogging

agent can also be used in the place of oil.



Avoid spray from spark plug hole when

cranking engine.

• Install and tighten spark plug. Do not connect spark plug wire.

• Clean the generator's outer surfaces. Check that cooling air

slots and openings on generator are open and unobstructed.

• Store the unit in a clean, dry place.

3.9 OTHER STORAGE TIPS

• Do not store gasoline from one season to another.

• Replace the gasoline can if it starts to rust. Rust and/or dirt in

the gasoline will cause problems with the carburetor and fuel

system.

• If possible, store the unit indoors and cover it to give protection

from dust and dirt. BE SURE TO EMPTY THE FUEL TANK.

• If it is not practical to empty the fuel tank and the unit is to

be stored for some time, use a commercially available fuel

stabilizer added to the gasoline to increase the life of the

gasoline. Start and run the engine for 10 - 15 minutes, after that

time and while the unit is running, turn the fuel shut-off valve

OFF and run until the engine stops from lack of fuel.

• Cover the unit with a suitable protective cover that does not

retain moisture.



NEVER cover the generator while engine and

exhaust areas are warm.

Maintenance

Troubleshooting

4.1 TROUBLESHOOTING GUIDE

PROBLEM CAUSE CORRECTION

Engine is running, but no AC output

is available.

1. Circuit breaker is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Fault in generator.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in good condition.

4. Contact Authorized Service Facility.

Engine runs well but bogs down

when loads are connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See “Don’t Overload the Generator” .

3. Contact Authorized Service Facility.

4. Contact Authorized Service Facility.

Engine will not start; or starts and

runs rough.

1. Fuel Shut-off is OFF.

2. Dirty air filter.

3. Out of gasoline.

4. Stale gasoline.

5. Spark plug wire not connected to spark plug.

6. Bad spark plug.

7. Water in gasoline.

8. Over-choking.

9. Low oil level.

10. Excessive rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Turn Fuel Shut-off to ON.

2. Clean or replace air filter.

3. Fill fuel tank.

4. Drain fuel tank and fill with fresh fuel.

5. Connect wire to spark plug.

6. Replace spark plug.

7. Drain fuel tank; fill with fresh fuel.

8. Put choke knob to No Choke position.

9. Fill crankcase to proper level.

10. Contact Authorized Service Facility.

11. Contact Authorized Service Facility.

12. Contact Authorized Service Facility.

Engine shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

3. Fault in engine.

1. Fill fuel tank.

2. Fill crankcase to proper level.

3. Contact Authorized Service Facility.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

1. Reduce load (see “Don’t Overload the Generator”).

2. Clean or replace air filter.

3. Contact Authorized Service Facility.

Engine “hunts” or falters. 1. Choke is opened too soon.

2. Carburetor is running too rich or too lean.

1. Move choke to halfway position until engine runs

smoothly.

2. Contact Authorized Service Facility.

Manual Part No. 0J3808 Rev. M (03/17/14)

La page charge ...

Honeywell 0061520 Le manuel du propriétaire

Marque: Honeywell

Modèle: 0061520

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell 0061520 Owner's manual
español: Honeywell 0061520 El manual del propietario

Honeywell 0061520 Le manuel du propriétaire

Honeywell 0061520 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents